Remove strings from s390 debugfeature entries that could lead to a
crash when the data is read from dbf because the strings do not exist
any more.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Most of the error conditions reported by a FICON storage server
indicate situations which can be recovered. Sometimes the host just
needs to retry an I/O request, but sometimes the recovery
is more complex and requires the device driver to wait, choose
a different path, etc.
The DASD device driver has a fully featured error recovery
for normal block layer I/O, but not for internal I/O request which
are for example used during the device bring up.
This can lead to situations where the IPL of a system fails because
DASD devices are not properly recognized.
This patch will extend the internal I/O handling to use the existing
error recovery procedures.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The DASD device driver needs to explicitly enable the prefix command
on the storage server, before it can be used. Originally we enabled
this command along with others only if we wanted to support PAV.
However, today we require this command for other features like
High Performance FICON as well, so we need to always enable prefix.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
the todclk.h header file is dead code. Remove it.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a DASD device is used with the DIAG discipline, the DIAG
initialization will indicate success or error with a respective
return code. So far we have interpreted a return code of 4 as error,
but it actually means that the initialization was successful, but
the device is read-only. To allow read-only devices to be used with
DIAG we need to accept a return code of 4 as success.
Re-initialization of the DIAG access is also part of the DIAG error
recovery. If we find that the access mode of a device has been
changed from writable to read-only while the device was in use,
we print an error message.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we detect a busy subchannel after the driver's set_offline
callback returned in ccw_device_set_offline, the current behavior
is to unregister the device, which may lead to undesired
consequences. Change this to just quiesce the subchannel and go on
with the offline processing.
Note: This is no excuse for not fixing these drivers -
after the set_offline callback they should have no running IO!
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve error recovery for internal I/Os by repeating each I/O
256 times per path to cope with long-running non-permanent error
conditions. Also retry each path twice to cope with link flapping,
i.e. single paths becoming unavailable in the order in which they
are tried.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
IO subchannels are always unregistered in process context, so use
spin_lock_irq in the corresponding remove callback.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure that there will be no more interrupts for an
unregistered device by using the same quiesce and disable loop
as in io_subchannel_shutdown.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Try to disable the old subchannel before we ask the driver core
to move the attached device to a new parent. This way we can use
the QUIESCE state during shutdown which prevents a possible use
after free situation in some error cases.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Handle a failing cio_disable_subchannel at the end of our device
recognition as if the recognition itself failed. This way
subsequent registration steps do not need to handle enabled
subchannels.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
DEV_STATE_QUIESCE is used to stop all IO on a busy subchannel.
This patch fixes the following problems related to the QUIESCE
state:
* Fix a potential race condition which could occur when the
resulting state was DEV_STATE_OFFLINE.
* Add missing locking around cio_disable_subchannel,
ccw_device_cancel_halt_clear and the cdev's handler.
* Loop until we know for sure that the subchannel is disabled.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The function ccw_device_unregister has to ensure to remove
all references obtained by device_add and device_initialize.
Unfortunately it gets called for devices which are
1) uninitialized, 2) initialized but unregistered, and
3) registered devices. To distinguish 1) and 2) this patch
introduces a new flag "initialized", which is 1 as long as we
hold the initial device reference.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We used to maintain a "registered" flag in our ccw_device_private
structure. This patch removes the "registered" flag and converts
all users of it to device_is_registered which has the exact same
meaning.
Note: The usage the atomic operation test_and_clear_bit is replaced
by the non-atomic if (device_is_registered()) device_del(). This
will not do harm, since we serialize calls to ccw_device_unregister
with a single-threaded workqueue.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
An Unconditional Reserve + Release operation (steal lock) for a
boxed device may fail when encountering special error cases
(e.g. unit checks or path errors). Fix this by using the more
robust ccw_request infrastructure for performing the steal lock
CCW program.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Set-pgid operations fail for some device types under z/VM for which
the hypervisor has already set the pgid. Also reserved devices or
changed pgids are not correctly recognized. Fix these problems by
using a combination of sense-pgid and set-pgid and by also accepting
pre-defined pgid settings.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split setting (driver wants feature enabled) and status (feature
setup was successful) for PGID related ccw device features so that
setup errors can be detected. Previously, incorrectly handled setup
errors could in rare cases lead to erratic I/O behavior and
permanently unusuable devices.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After changing all internal I/O functions to use the newly introduced
ccw request infrastructure, retries are handled automatically after a
clear operation. Therefore remove the internal retry flag and
associated code.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Accept a request for setting a not-operational device offline.
This way, users can remove devices from Linux which would otherwise
remain unusable until reboot.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the newly introduced ccw request infrastructure to implement
pgid related operations: sense pgid, set pgid and disband pg.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the newly introduced ccw request infrastructure to implement
the sense id operation.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reduce code duplication by introducing a central infrastructure to
perform an internal I/O operation on a CCW device.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the call to BUG() for situations which are unexpected
but do not cause actual problems.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Device recognition needs to be started with the ccw device lock
held to prevent race conditions between I/O starting and interrupt
reception.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Handle verification errors consistently through the existing
callback ccw_device_done to reduce cleanup code duplication.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the return code from ccw_device_recognition and handle
recognition errors through the existing callback
ccw_device_recog_done to reduce cleanup code duplication.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Print a warning message in case a ccw device enters boxed or
not operational state during online/offline processing.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a central mechanism for performing delayed ccw device work
to ensure that different types of work do not overwrite each other.
Prioritization ensures that the most important work is always
performed while less important tasks are either obsoleted or repeated
later.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure that current and future users of sch->work do not overwrite
each other by introducing a single mechanism for delayed subchannel
work.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the initiative to update subchannel-ccw device associations
to the subchannel: when there is an indication that the internal
association no longer reflects the current hardware state, mark
each affected subchannel as requiring attention. Once processing
reaches a subchannel, determine the correct association for that
subchannel at that time and perform the necessary device_move
operations.
This change fixes problems with the previous approach which would
leave devices in an inconsistent state when a new hardware change
occurred while a device_move was already scheduled.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sch_create_and_recog_new_device() associates a parent subchannel
with its ccw device child even though this is already done by
the subsequently called io_subchannel_recog(). Also make sure
io_subchannel_recog() sets the association under lock.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
io_subchannel_probe() frees memory for sch->private which is later
freed again when io_subchannel_remove() is called. Fix this problem
by removing the cleanup in io_subchannel_probe().
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
"Definition" is misspelled "defintion" in several comments; this
patch fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP is never set and hence can
be removed. This is a leftover from the time when zfcp had to decide
whether the target supports a "logical unit reset" or not. Nowadays,
the SCSI midlayer calls the eh_device_reset_handler or the
eh_target_reset_handler and zfcp simply maps this to a "logical unit
reset" or a "target reset".
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Enable the display of supported and active fc4s for zfcp in the FC
transport class. zfcp only supports FCP, so simply hard-code this
information. The zfcp hbaapi already has this information hardcoded,
but this would allow to switch from the coding in the zfcp hbaapi to
the common FC transport attributes in the future.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In case the SCSI error recovery starts because of a SCSI command
timeout, but then something else triggers the rport to be deleted, the
SCSI error recovery will run to the end and set the SCSI device
offline. To prevent this, call the FC transport function
fc_block_scsi_eh which waits until the rport leaves the BLOCKED state.
This guarantees that communication is possible if the rport is ONLINE,
or the SCSI devices will be removed if the rport state switches to
NOT_PRESENT.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The SCSI midlayer retries commands based on the remote port state and
the command status reported by the driver. Returning
DID_TRANSPORT_DISRUPTED is a better approach, use this for reporting
FSF errors back to the SCSI midlayer. See
http://marc.info/?l=linux-scsi&m=125668044215051&w=2 as reference.
There is also no need in special treatment of ABORTED commands, so
remove the ZFCP_STATUS_FSFREQ_ABORTED, the commands are then returned
with DID_TRANSPORT_DISRUPTED.
Also remove the ZFCP_STATUS_FSFREQ_RETRY: It is useless, no retry is
happening in the FSF layer and nobody checks the state of this flag.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Introduce kmem_cache for ELS ADISC data to guarantee the required
hardware alignment and free the allocated memory in case the send
failes.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove some redundancies in FC related code and trace:
- drop redundant data from SAN trace (local s_id that only changes
during link down, ls_code that is already part of payload, d_id in
ct response trace that is always the same as in ct request trace)
- use one common fsf struct to hold zfcp data for ct and els requests
- leverage common fsf struct for FC passthrough job data, allocate it
with dd_bsg_data for passthrough requests and unify common code for
ct and els passthrough request
- simplify callback handling in zfcp_fc
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Instead of assigning 4 bytes with the highest byte masked out, use a 3
byte array with the ntoh24 and h24ton helper functions, thus
eliminating the need for the ZFCP_DID_MASK.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The well-known-address (WKA) port handling code is part of the FC code
in zfcp. Move everything WKA related to the zfcp_fc files and use the
common zfcp_fc prefix for structs and functions. Drop the unused key
management service while renaming the struct, no request could ever
reach this service in zfcp and it is obsolete anyway.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use common code definitions for FC GPN_FT and GID_PN
instead of inventing private ones. Move the private structs still
required inside zfcp to zfcp_fc header file.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use common code definitions for FC plogi, logo, rscn and adisc structs
instead of inventing private ones. Move the private struct for issuing
ELS ADISC inside zfcp to zfcp_fc header file.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use common data structures for FCP CMND, FCP RSP and related
definitions and remove zfcp private definitions. Split the FCP CMND
setup and FCP RSP evaluation code in seperate functions. Use inline
functions to not negatively impact the I/O path.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If an error occurs that triggers the call to fc_remote_port_delete,
ideally this call would happen before any I/O is passed back to the
SCSI midlayer through scsi_done. The SCSI midlayer will retry the
commands and fc_remote_port_chkready will return the correct status
code. But with the delay between calling scsi_done in softirq context
and the call to fc_remote_port_delete from the workqueue, there is a
window where zfcp returns DID_ERROR. This leads to SCSI error recovery
which then leads to offline SCSI devices since all recovery actions
will fail with the rport now being blocked.
In this window, zfcp has to return DID_IMM_RETRY just as the FC
transport class would do in fc_remote_port_chkready for the blocked
fc_rport. As soon as the fc_rport is BLOCKED, fc_remote_port_chkready
will do the right thing.
Additionally, there are two more cases to catch in zfcp_scsi_queuecommand:
- After the port has been opened, the unit has to be opened. During
this period I/O has to be retried. This can also be handled with
DID_IMM_RETRY.
- If the access to the unit fails, but the port is good, then
this single unit cannot be accessed and I/O to this unit has to fail
without involving the FC transport class.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The port_scan work was scheduled to the work_queue provided by the
kernel. This resulted on SMP systems to a likely situation that more
than one scan_work were processed in parallel. This is not required
and openes the possibility of race conditions between the removal of
invalid ports and the enqueue of just scanned ports. This patch
synchronizes the scan_work tasks by scheduling them to adapter local
work_queue.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The flag ZFCP_STATUS_COMMON_REMOVE was used to indicate that a
resource is not ready to be used or about to be removed from the
system. This is now better done by an improved list handling
and therefore the additional indicator is not required anymore.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
With the reference counting for zfcp data structures, it is now
possible to implement module unloading again. Module unloading
requires to free all data structures in the module exit function. This
is done by unregistering zfcp from s390 cio and the SCSI midlayer
first in the module exit function.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The latencies traced per fsf request are traced for sysfs output and
for blktrace, each in one function. Simplify the tracing code by
merging both tracing functions into one.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When accessing port and unit attributes, use container_of instead of
dev_get_drvdata. This eliminates some code checker warnings about
aliased access of data structures.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The callback for suspend is not required because it contains exactly
the same functionality as the _set_offline routine does.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The global config_mutex was required for the serialization of a
configuration change within the zfcp driver. This global locking is
now obsolete and can be removed. The requirement of serializing the
access to a zfcp_adapter reference via a ccw_device is realized wth a
static spinlock.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace the local reference counting by already available mechanisms
offered by kref. Where possible existing device structures were used,
including the same functionality.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The global config_lock was used to protect the configuration organized
in independent lists. It is not necessary to have a lock on driver
level for this purpose. This patch replaces the global config_lock
with a set of local list locks.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adapt the change_queue_depth callback in zfcp for the new reason
parameter. Simply pass each call back to the SCSI midlayer, there are
no resource adjustments necessary for zfcp.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Removes check for (depth <= default_depth) in case of
SCSI_QDEPTH_RAMP_UP call back, not needed after added
max_queue_depth per sdev.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add missing 'const' attribute to avoid the following compile warnings:
drivers/s390/net/ctcm_main.c: In function 'ctcm_init':
drivers/s390/net/ctcm_main.c:1864: warning: assignment from incompatible pointer type
drivers/s390/net/lcs.c: In function 'lcs_init_module':
drivers/s390/net/lcs.c:2468: warning: assignment from incompatible pointer type
drivers/s390/net/claw.c: In function 'claw_init':
drivers/s390/net/claw.c:3408: warning: assignment from incompatible pointer type
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Technically there is no need to set the card offline to change
RX checksumming. Get rid of this stupid limitation.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum TSO size OSA can handle is 15 * PAGE_SIZE. This
patch reduces gso_max_size to this value and adds some sanity
checks and statistics to the TSO implementation.
Since only layer 3 is able to do TSO move all TSO related functions
to the qeth_l3 module.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a qeth device online requires to call function
ccw_device_set_online() for read-, write-, and data-subchannel.
Failures should be detected immediately without an attempt to
invoke follow-on activity qeth_qdio_clear_card().,
In addition, ccw_device_set_online calls are consolidated in
qeth_core_main.c only.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EDDP code has been removed from qeth in 2009. This patch removes two
useless remaining EDDP-references.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Isolate data connection to a shared OSA card against other data
connections to the same OSA card. Connectivity between isolated
data connections sharing the same OSA card is therefore possible only
through external network gear (e.g. a router).
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_bytes value must be updated by skb length before skb is freed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cu3088-driver used as common base for lcs- and ctcm-devices
makes it difficult to assign the appropriate driver to an lcs-device
or a ctcm-device. This patch eliminates the cu3088-driver and thus
the root device "cu3088". Path /sys/devices/cu3088 is replaced with
the pathes /sys/devices/lcs and /sys/devices/ctcm.
Patch is based on a proposal from Cornelia Huck.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State transition to DEV_STATE_STOPPED indicates all outstanding I/O has
finished. Add wait queue to wait for this state.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a system where the ctrl-alt-del init action initiated by signal
quiesce suspends the machine the quiesce handler override for
_machine_restart, _machine_halt and _machine_power_off needs to be
undone, otherwise the override is still present in the resumed
system. The next shutdown would then load the quiesce state psw
instead of performing the correct shutdown action.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The monreader device driver doesn't set dev->driver_data to NULL after
freeing the corresponding data structure. This leads to a use after
free bug in the freeze/thaw suspend/resume functions after the device
has been opened and closed once. Fix this by clearing dev->driver_data
in the close() function.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that sys_sysctl is a generic wrapper around /proc/sys .ctl_name
and .strategy members of sysctl tables are dead code. Remove them.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Allow the architecture to request a normal jiffy tick when the system
goes idle and tick_nohz_stop_sched_tick is called . On s390 the hook is
used to prevent the system going fully idle if there has been an
interrupt other than a clock comparator interrupt since the last wakeup.
On s390 the HiperSockets response time for 1 connection ping-pong goes
down from 42 to 34 microseconds. The CPU cost decreases by 27%.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
LKML-Reference: <20090929122533.402715150@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] zfcp: Flush SCSI registration work when adding unit
[SCSI] zfcp: Fix timer initialization for ct and els requests
[SCSI] zfcp: Warn about storage devices with broken PLOGI data
[SCSI] zfcp: Handle WWPN mismatch in PLOGI payload
[SCSI] zfcp: fix kfree handling in zfcp_init_device_setup
[SCSI] fix memory leak in initialization
After copying uts->nodename to the static nodename array the static
version isn't necessarily zero termininated, since the size of the
array is one byte too short.
Afterwards doing strncat(data, nodename, strlen(nodename)); may copy
an arbitrary large amount of bytes.
Fix this by getting rid of the static array and using strncat with
proper length limit.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix missing unregister_sysctl_table in case the SCLP doesn't provide
the requested feature. Also simplify the whole error handling while
at it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a suspended z/VM guest has been logged off before the resume the
'SET SMSG IUCV' CP command need to be repeated to reenable sending
message via SMSG. This fixes the following error:
HCPMFS057I H4214002 not receiving; SMSG off
Error: non-zero CP response for command 'SMSG H4214002 CMM SHRINK 5010': #57
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the size of the local buffer and use snprintf to prevent
further miscalculations. Also fix the usage of bitwise vs logic
operations.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch updates misc percpu related symbols such that percpu
symbols are unique and don't clash with local symbols. This serves
two purposes of decreasing the possibility of global percpu symbol
collision and allowing dropping per_cpu__ prefix from percpu symbols.
* drivers/crypto/padlock-aes.c: s/last_cword/paes_last_cword/
* drivers/lguest/x86/core.c: s/last_cpu/lg_last_cpu/
* drivers/s390/net/netiucv.c: rename the variable used in a macro to
avoid clashing with percpu symbol
* arch/mn10300/kernel/kprobes.c: replace current_ prefix with cur_ for
static variables. Please note that percpu symbol current_kprobe
can't be changed as it's used by generic code.
Partly based on Rusty Russell's "alloc_percpu: rename percpu vars
which cause name clashes" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
When configuring a LUN for use in zfcp, flush the SCSI work to ensure
the SCSI device has been created before returning. This means that a
configuration procedure can run these commands in a script and the
SCSI device is available immediately after the unit_add:
echo 1 > /sys/bus/ccw/drivers/zfcp/0.0.181d/online
echo 0x401040C300000000 > \
/sys/bus/ccw/drivers/zfcp/0.0.181d/0x500507630313c562/unit_add
lsscsi
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add HZ since the start_timer function expects jiffies, not seconds.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After opening a remote port zfcp checks if the WWPN returned in the
PLOGI maches the WWPN of the port that should have been opened. On a
mismatch zfcp assumes that the DID just changed, queries the FC
nameserver and tries again. If the situation persists the erp will
give up.
With this strategy, if the remote port always returns the wrong PLOGI
data, the remote port will not be opened. Introduce a warning, so that
the system administrator knows why the remote port is not being opened
and to have a pointer to investigate the problem on the storage
system.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For ports, zfcp gets the DID from the FC nameserver and tries to open
the port. If the open succeeds, zfcp compares the WWPN from the
nameserver with the WWPN in the PLOGI payload. In case of a mismatch,
zfcp assumes that the DID of the port just changed and we opened the
wrong port. This means that zfcp has to forget the DID, lookup the DID
again and retry.
This error case had a problem that zfcp forgets the DID, but never
looks up a new one, stalling the ERP in this case. Fix this by
triggering the DID lookup and properly exit from the ERP. The DID
lookup will trigger a new ERP action.
Also ensure when trying to open the port again with the new DID, first
close the open port, even in the NOESC case.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The pointer that is allocated with kmalloc() is passed to strsep()
which modifies it. Later on the modified pointer value will be passed
to kfree. Save the original pointer and pass that one to kfree
instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Group device now cleanly reacts to failures during channel start and
implements a clean rollback.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The creation of a new lcs device requires a call to the function
ccw_device_set_online() for the read and the write channel. Failure
of either call should terminate the lcs device creation immediately
with return code -ENODEV.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timer_list structure in lcs_send_lancmd() is allocated on stack.
Initialization with init_timer() leads to above ODEBUG message.
Instead use init_timer_on_stack() which prevents above msg.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this build error:
next-20091013 randconfig build on s390x build breaks with
drivers/s390/built-in.o:(.data+0x3354): undefined reference to `sclp_vt220_pm_event_fn'
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <michael.holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use cio_is_console() in io_subchannel_probe to indicate that the
special handling is console specific. As long as there is no other
subchannel for which this might be true, it is misleading to speak
of "early devices". Should more of these devices be introduced,
a cleanup of all console special handling is in order anyway.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
8d65af78 "sysctl: remove "struct file *" argument of ->proc_handler"
removed the struct file argument from all proc_handlers but didn't
change the call home proc handler (or call home was merged later).
So fix this now.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Hans-Joachim Picht <hans@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the rdc_buffer is above 2G we need indirect addresssing so we have
to use an idaw to give the rdc_buffer to the ccw.
If the rdc_buffer is under 2G nothing changes.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace spin_lock with spin_lock_irqsave in dasd_eckd_restore_device.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When setting a channel attached tape online under Linux 2.6.31, the
"vol_id" process from udev hangs in sync_page():
2 sync_page+144 [0x1dfaac]
3 __wait_on_bit_lock+194 [0x58c23e]
4 __lock_page+116 [0x1df9dc]
5 truncate_inode_pages_range+728 [0x1ed7cc]
6 __blkdev_put+244 [0x25f738]
7 __fput+300 [0x229c4c]
8 filp_close+122 [0x225a3a]
The reason for that is an error in the request queue handling. It can
happen that we fetch a request, but do not process it further because
the number of queued requests exceeds TAPEBLOCK_MIN_REQUEUE.
To fix this, we should call blk_peek_request() instead of
blk_fetch_request() in the while condition and fetch the request in
the loop body afterwards.
This bug was introduced with the patch "block: implement and enforce
request peek/start/fetch" (9934c8c045)
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (34 commits)
[SCSI] qla2xxx: Fix NULL ptr deref bug in fail path during queue create
[SCSI] st: fix possible memory use after free after MTSETBLK ioctl
[SCSI] be2iscsi: Moving to pci_pools v3
[SCSI] libiscsi: iscsi_session_setup to allow for private space
[SCSI] be2iscsi: add 10Gbps iSCSI - BladeEngine 2 driver
[SCSI] zfcp: Fix hang when offlining device with offline chpid
[SCSI] zfcp: Fix lockdep warning when offlining device with offline chpid
[SCSI] zfcp: Fix oops during shutdown of offline device
[SCSI] zfcp: Fix initial device and cfdc for delayed adapter allocation
[SCSI] zfcp: correctly initialize unchained requests
[SCSI] mpt2sas: Bump version 02.100.03.00
[SCSI] mpt2sas: Support dev remove when phy status is MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT
[SCSI] mpt2sas: Timeout occurred within the HANDSHAKE logic while waiting on firmware to ACK.
[SCSI] mpt2sas: Call init_completion on a per request basis.
[SCSI] mpt2sas: Target Reset will be issued from Interrupt context.
[SCSI] mpt2sas: Added SCSIIO, Internal and high priority memory pools to support multiple TM
[SCSI] mpt2sas: Copyright change to 2009.
[SCSI] mpt2sas: Added mpi2_history.txt for MPI2 headers.
[SCSI] mpt2sas: Update driver to MPI2 REV K headers.
[SCSI] bfa: Brocade BFA FC SCSI driver
...
There is a race while re-reading the device characteristics. After
cleaning the memory area a cqr is build which reads the device
characteristics. This may take a rather long time and the device
characteristics structure is zero during this. Now it could be
possible that the block tasklet starts working and a new cqr will be
build. The build_cp command refers to the device characteristics
structure and this may lead into a divide by zero exception.
Fix this by re-reading the device characteristics into a temporary
structur and copy the data to the original structure. Also take the
ccwdev_lock.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve the comments for switch cases without a break. This fixes
some warnings of a code checker tool.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow users to set boxed devices offline. After setting them
offline, the device state will still be boxed.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a ccw device appears not operational, inform the associated
device driver and act according to the response: if the driver
wants to keep the device, put it into the disconnected state.
If not, or if there is no driver or if the device is not online,
unregister it. This approach is consistent with no-path event
handling.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When there is no path left to a ccw device, inform the associated
device driver and act according to the response: if the driver
wants to keep the device, put it into the disconnected state.
If not, or if there is no driver or if the device is not online,
unregister it.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is a memory leak in /proc/cio_ignore. The iterator is allocated
in cio_ignore_proc_seq_start, but never freed in
cio_ignore_proc_seq_stop, because we cannot use the iterator
that was passed by seqfile. The seqfile interface passes the last
seen iterator to the stop function and not the first one. Since our
next function will return NULL at the end, the iter passed to
cio_ignore_proc_seq_stop is NULL. The original iter has leaked.
The solution is to use seq_open_private.
Found with kmemleak:
unreferenced object 0x1c720580 (size 32):
comm "head", pid 973, jiffies 4294958302
hex dump (first 32 bytes):
00 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<0000000000203154>] kmem_cache_alloc+0x190/0x19c
[<00000000003fb462>] cio_ignore_proc_seq_start+0x5e/0x128
[<0000000000231018>] seq_read+0xc8/0x4bc
[<0000000000273954>] proc_reg_read+0xa8/0xf4
[<000000000020e3d8>] vfs_read+0xac/0x1a4
[<000000000020e5c6>] SyS_read+0x52/0xa8
[<000000000011836e>] sysc_noemu+0x10/0x16
[<0000004690b7936c>] 0x4690b7936c
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move dev_set_name to when we know that the device will actually be
registered in order to avoid a memory leak if the allocated memory
for the channel path has to be freed.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this build failure:
drivers/s390/built-in.o: In function `raw3270_pm_unfreeze':
(.text+0x3ac04): undefined reference to `ccw_device_force_console'
with:
CONFIG_TN3270=y
CONFIG_TN3270_CONSOLE=n
CONFIG_TN3215_CONSOLE=n
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This string query operation was supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert qeth's
implementation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running chchp --vary 0 and chccwdev -d on a FCP device with scsi
devices attached can lead to this thread hanging:
================================================================
STACK TRACE FOR TASK: 0x2fbfcc00 (kslowcrw)
STACK:
0 schedule+1136 [0x45f99c]
1 schedule_timeout+534 [0x46054e]
2 wait_for_common+374 [0x45f442]
3 blk_execute_rq+160 [0x217a2c]
4 scsi_execute+278 [0x26daf2]
5 scsi_execute_req+150 [0x26dc86]
6 sd_sync_cache+138 [0x28460a]
7 sd_shutdown+130 [0x28486a]
8 sd_remove+104 [0x284c84]
9 __device_release_driver+152 [0x257430]
10 device_release_driver+56 [0x2575c8]
11 bus_remove_device+214 [0x25672a]
12 device_del+352 [0x25456c]
13 __scsi_remove_device+108 [0x272630]
14 scsi_remove_device+66 [0x2726ba]
15 zfcp_ccw_remove+824 [0x335558]
16 ccw_device_remove+62 [0x2b3f2a]
17 __device_release_driver+152 [0x257430]
18 device_release_driver+56 [0x2575c8]
19 bus_remove_device+214 [0x25672a]
20 device_del+352 [0x25456c]
21 ccw_device_unregister+92 [0x2b48c4]
22 io_subchannel_remove+108 [0x2b4950]
23 css_remove+62 [0x2af7ee]
24 __device_release_driver+152 [0x257430]
25 device_release_driver+56 [0x2575c8]
26 bus_remove_device+214 [0x25672a]
27 device_del+352 [0x25456c]
28 device_unregister+38 [0x25464a]
29 css_sch_device_unregister+68 [0x2af97c]
30 ccw_device_call_sch_unregister+78 [0x2b581e]
31 worker_thread+604 [0x69eb0]
32 kthread+154 [0x6ff42]
33 kernel_thread_starter+6 [0x1c952]
================================================================
The problem is that the chchp --vary 0 leads to zfcp first calling
fc_remote_port_delete which blocks all scsi devices on the remote
port. Calling scsi_remove_device later lets the sd driver issue a
SYNCHRONIZE_CACHE command. This command stays on the "stopped" request
requeue because the SCSI device is blocked. Fix this by first removing
the scsi and fc hosts which removes all scsi devices and do not use
scsi_remove_device.
Reviewed-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-39.x.20090917-s390xdefault #1
-------------------------------------------------------
kslowcrw/83 is trying to acquire lock:
(&adapter->scan_work){+.+.+.}, at: [<0000000000169c5c>] __cancel_work_timer+0x64/0x3d4
but task is already holding lock:
(&zfcp_data.config_mutex){+.+.+.}, at: [<00000000004671ea>] zfcp_ccw_remove+0x66/0x384
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&zfcp_data.config_mutex){+.+.+.}:
[<0000000000189962>] __lock_acquire+0xe26/0x1834
[<000000000018a4b6>] lock_acquire+0x146/0x178
[<000000000058cb5a>] mutex_lock_nested+0x82/0x3ec
[<0000000000477170>] zfcp_fc_scan_ports+0x3ec/0x728
[<0000000000168e34>] worker_thread+0x278/0x3a8
[<000000000016ff08>] kthread+0x9c/0xa4
[<0000000000109ebe>] kernel_thread_starter+0x6/0xc
[<0000000000109eb8>] kernel_thread_starter+0x0/0xc
-> #0 (&adapter->scan_work){+.+.+.}:
[<0000000000189e60>] __lock_acquire+0x1324/0x1834
[<000000000018a4b6>] lock_acquire+0x146/0x178
[<0000000000169c9a>] __cancel_work_timer+0xa2/0x3d4
[<0000000000465cb2>] zfcp_adapter_dequeue+0x32/0x14c
[<00000000004673e4>] zfcp_ccw_remove+0x260/0x384
[<00000000004250f6>] ccw_device_remove+0x42/0x1ac
[<00000000003cb6be>] __device_release_driver+0x9a/0x10c
[<00000000003cb856>] device_release_driver+0x3a/0x4c
[<00000000003ca94c>] bus_remove_device+0xcc/0x114
[<00000000003c8506>] device_del+0x162/0x21c
[<0000000000425ff2>] ccw_device_unregister+0x5e/0x7c
[<000000000042607e>] io_subchannel_remove+0x6e/0x9c
[<000000000041ff9a>] css_remove+0x3e/0x7c
[<00000000003cb6be>] __device_release_driver+0x9a/0x10c
[<00000000003cb856>] device_release_driver+0x3a/0x4c
[<00000000003ca94c>] bus_remove_device+0xcc/0x114
[<00000000003c8506>] device_del+0x162/0x21c
[<00000000003c85e8>] device_unregister+0x28/0x38
[<0000000000420152>] css_sch_device_unregister+0x46/0x58
[<00000000004276a6>] io_subchannel_sch_event+0x28e/0x794
[<0000000000420442>] css_evaluate_known_subchannel+0x46/0xd0
[<0000000000420ebc>] slow_eval_known_fn+0x88/0xa0
[<00000000003caffa>] bus_for_each_dev+0x7e/0xd0
[<000000000042188c>] for_each_subchannel_staged+0x6c/0xd4
[<0000000000421a00>] css_slow_path_func+0x54/0xd8
[<0000000000168e34>] worker_thread+0x278/0x3a8
[<000000000016ff08>] kthread+0x9c/0xa4
[<0000000000109ebe>] kernel_thread_starter+0x6/0xc
[<0000000000109eb8>] kernel_thread_starter+0x0/0xc
cancel_work_sync is called while holding the config_mutex. But the
work that is being cancelled or flushed also uses the config_mutex.
Fix the resulting deadlock possibility by calling cancel_work_sync
earlier without holding the mutex. The best place to do is is after
offlining the device. No new port scan work will be scheduled for the
offline device, so this is a safe place to call cancel_work_sync.
Reviewed-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
With the change that the zfcp_adapter struct is only allocated when
the device is set online, the shutdown handler has to check for a
non-existing zfcp_adapter struct. On the other hand, this check is not
necessary in the offline callback, since an online device has the
zfcp_adapter allocated and we go through the offline callback before
removing the ccw device.
Reviewed-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
With the change for delaying the allocation of zfcp_adapter, the
initial device parameter function has to first call
ccw_device_set_online which allocates the zfcp_adapter structure.
Change this and adapt the cfdc part accordingly.
Reviewed-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The common initialization of ct/gs and els requests missed the
initialization of unchained requests. Fix this by moving the common
parts to a place that is called for all ct/gs and els requests.
Reviewed-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* remove asm/atomic.h inclusion from linux/utsname.h --
not needed after kref conversion
* remove linux/utsname.h inclusion from files which do not need it
NOTE: it looks like fs/binfmt_elf.c do not need utsname.h, however
due to some personality stuff it _is_ needed -- cowardly leave ELF-related
headers and files alone.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (22 commits)
[S390] Update default configuration.
[S390] hibernate: Do real CPU swap at resume time
[S390] dasd: tolerate devices that have no feature codes
[S390] zcrypt: Do not add/remove devices in s/r callbacks
[S390] hibernate: make sure pfn_is_nosave handles lowcore pages
[S390] smp: introduce LC_ORDER and simplify lowcore handling
[S390] ptrace: use common code for simple peek/poke operations
[S390] fix disabled_wait inline assembly clobber list
[S390] Change kernel_page_present coding style.
[S390] hibernation: reset system after resume
[S390] hibernation: fix guest page hinting related crash
[S390] Get rid of init_module/delete_module compat functions.
[S390] Convert sys_execve to function with parameters.
[S390] Convert sys_clone to function with parameters.
[S390] qdio: change state of all primed input buffers
[S390] qdio: reduce per device debug messages
[S390] cio: introduce consistent subchannel scanning
[S390] cio: idset use actual number of ssids
[S390] cio: dont kfree vmalloced memory
[S390] cio: introduce css_settle
...
The DASD device driver reads the feature codes of a device during
device initialization. These codes are later used to determine the
availability of advanced features like PAV or High Performance FICON.
Some very old devices do not support the command to read feature
codes and the initialization routine fails.
As the feature codes are not necessary for basic DASD operations, we
can support such devices by just ignoring missing feature codes.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Devices are no longer removed or added in the suspend and resume
callbacks. Instead they are marked unregistered in suspend. In the
resume callback the ap_scan_bus method is scheduled. The bus scan
function will remove the old device and add new ones. This way all
the device handling will be done in only one function. Additionaly
the case where the domain might change during suspend/resume is
caught. In that case the devices qid needs to re-calculated in
order of having it found by the scan method.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If input buffers stay in primed state qdio may not receive further interrupts
for the input queue depending on the firmware. That can cause a connection
hang on OSA cards.
Change the state of all primed input buffers that are not acknowledged to
not initialized.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Even if turned off the debug message overhead is measurable in the hot path.
Reduce the number of debug message calls in do_QDIO and qdio_kick_handler.
Also use hex numbers to save space in the debug entries.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Previously, there were multiple subchannel scanning mechanisms
which could potentially conflict with each other. Fix this problem
by moving blacklist and ccw driver triggered scanning to the
existing evaluation method.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The functions idset_sch_new and for_each_subchannel_staged
use different values for the number of subchannel sets. Make
it consistent by changing idset_sch_new to also use the actual
number of subchannel sets.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't use kfree to free memory allocated by vmalloc.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the css_driver callback settle which can be implemented
by a subchannel driver to wait for the subchannel type specific
asynchronous work to finish.
In channel_subsystem_init_sync we call that for each subchannel
driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use css_eval_scheduled to determine if all scheduled subchannel
evaluation is finished. Wait for this value to be 0 in the
channel subsystem init function.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define initialization sequence of css and ccw bus init calls by merging
them into a single init call. Also introduce channel_subsystem_init_sync
to wait for the initialization of devices to finish.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (209 commits)
[SCSI] fix oops during scsi scanning
[SCSI] libsrp: fix memory leak in srp_ring_free()
[SCSI] libiscsi, bnx2i: make bound ep check common
[SCSI] libiscsi: add completion function for drivers that do not need pdu processing
[SCSI] scsi_dh_rdac: changes for rdac debug logging
[SCSI] scsi_dh_rdac: changes to collect the rdac debug information during the initialization
[SCSI] scsi_dh_rdac: move the init code from rdac_activate to rdac_bus_attach
[SCSI] sg: fix oops in the error path in sg_build_indirect()
[SCSI] mptsas : Bump version to 3.04.12
[SCSI] mptsas : FW event thread and scsi mid layer deadlock in SYNCHRONIZE CACHE command
[SCSI] mptsas : Send DID_NO_CONNECT for pending IOs of removed device
[SCSI] mptsas : PAE Kernel more than 4 GB kernel panic
[SCSI] mptsas : NULL pointer on big endian systems causing Expander not to tear off
[SCSI] mptsas : Sanity check for phyinfo is added
[SCSI] scsi_dh_rdac: Add support for Sun StorageTek ST2500, ST2510 and ST2530
[SCSI] pmcraid: PMC-Sierra MaxRAID driver to support 6Gb/s SAS RAID controller
[SCSI] qla2xxx: Update version number to 8.03.01-k6.
[SCSI] qla2xxx: Properly delete rports attached to a vport.
[SCSI] qla2xxx: Correct various NPIV issues.
[SCSI] qla2xxx: Correct qla2x00_eh_wait_on_command() to wait correctly.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
For messages from the tape core that is shared between the 3590 and 34xx
tape disciplines, we want to have the "tape" prefix instead of "tape_3590"
or "tape_34xx". In order to fix this, we now use the pr_xxx printk macros.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge cpuid.h header file into cpu.h.
While at it convert from typedef to struct declaration and also
convert cio code to use proper lowcore structure instead of casts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently, when a tape device is set online and no cartridge is loaded, we
get the messages "The tape cartridge has been successfully unloaded" and
"Determining the size of the recorded area". These messages are not correct.
To fix this, we now print the "cartridge loaded/unloaded" messages only,
when the load/unload event really occurs. In addition to that, the message
"Determining the size of the recorded area" is only printed, if a cartridge
is loaded.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use a console_initcall() to initialize the s390 virtio console and
clean up s390 console initialization in setup.c.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If dev_set_name fails during scanning the AP bus, the reserved memory
has to be freed.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently in the suspend process checksums for the XPRAM partitions are
created and stored. During the resume process it is checked,
if the checksums are still the same. If this is not the case, a kernel panic
is triggered. Unfortunately this prevents XPRAM from beeing used as suspend
device, because in this case after the checksum has been created, the
memory image is written to XPRAM and therefore the contents of the suspend
partition is changed. In order to allow XPRAM to be used as suspend device,
this patch removes the checksum validation.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vmur class is allocated after the CCW driver is registered
and it is destroyed before the CCW driver is unregistered.
This is not the correct sequence, because the vmur class can be used
via driver core callbacks that are triggered during the CCW driver
deregistration. For Example:
1. vmur device is online
2. vmur module is unloaded
This leads to the following function call stack:
<4> [<0000000000387286>] device_destroy+0x36/0x5c
<4> [<000003e000209714>] ur_set_offline_force+0x9c/0x10c [vmur]
<4> [<000003e00020a928>] ur_remove+0x64/0xbc [vmur]
<4> [<00000000003e4d2e>] ccw_device_remove+0x42/0x1ac
<4> [<000000000038a1aa>] __device_release_driver+0x9a/0xe4
<4> [<000000000038a2da>] driver_detach+0xe6/0xec
<4> [<0000000000388ee4>] bus_remove_driver+0xc0/0x108
<4> [<000003e00020ad5a>] ur_exit+0x52/0x84 [vmur]
In device_destroy() the vmur class is used. Since it is already freed,
this can lead to a kernel panic.
To fix the problem, the vmur class has to be allocated before the CCW
driver is registered and destroyed after the CCW driver has ben unregistered.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With CONFIG_DEBUG_OBJECTS_TIMERS=y "chccwdev --online" for a tape device
will fail with message "ODEBUG: object is on stack, but not annotated".
We now use init_timer_on_stack.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Don't use kfree directly after device registration started.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch fixes message naming so that generic dasd messages do not
contain the device discipline. For this purpose the dev_ makros are
replaced by pr_ makros for generic dasd messages.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A DASD device that is not ready or online has no defined disk layout,
so all requests that arrive in such a state need to be returned as
failed.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We used the init_name to set the console ccw_device's name early
at the boot stage. This patch moves the name setting (for all ccw
devices) to the point where we actually register the device. At this
time we can do dynamic allocations and therefore use dev_set_name.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We use a test_and_clear_bit to prevent a device from being
unregistered twice. Unfortunately in this cases the "final"
put_device (from device_initialize) was issued more than once,
resulting in an use after free error. Fix this by moving this
put_device to ccw_device_unregister.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We used the init_name to set the console subchannels name early
at the boot stage. With the patch cio: fix memleak in subchannel validation
we moved the name setting to the point where we actually register the
console subchannel. At this time we can do dynamic allocations and therefore
use dev_set_name.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When scanning for new subchannels we have a code path where we allocate
memory for a struct subchannel, set the device name (which is dynamically
allocated now) and do a check if the underlying device is blacklisted - if
so we free the subchannel structure.
Since we have not set up refcounting at this stage, the device name's memory
is lost. Fix this by moving the dev_set_name after the blacklist test.
Note: With this patch the init_name for the console subchannel becomes
virtually obsolete.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When using s390dbf with "%s" in sprintf format strings the string itself
is not copied to the dbf buffer.
Since in this case only pointers are stored in the s390dbf, we should
not use dev_name - which is bound to the lifetime of the device.
Reading this entry from s390dbf after the device was released will cause
an use after free error.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The number of qdio debugfs entries was limited. Remove this limit
and group the queue files in a per device directory.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When unit checks trigger sensing the device state is set to W4SENSE
until sense completion; then the device state is set back to
ONLINE. If a unit check occurs while set online or set offline
requests are processed then it might happen that the device's
temporary W4SENSE state causes these functions to terminate,
leaving the device in an inconsistent state when the state is set
back to ONLINE later on so that the device cannot be set online or
offline any longer.
To solve this, set online/offline and related rollback or error
routines are processed only if the device is in a final or
DISCONNECTED state.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure to always hold an extra device reference for scheduling a
subchannel deregistration, by moving the get_device to
ccw_device_schedule_sch_unregister. This fixes an use after free
error in ccw_device_call_sch_unregister where put_device was called
on an already freed device structure.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With commit c38f960809 polling was
stopped for the queue even if new data is available.
Return immediately after scheduling the queue tasklet if the queue
is not done.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move debug traces for start I/O and interrupt events to exclusive
trace levels. Also change tracing in hot-path from sprintf (costly)
to hex.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If online/offline processing of a ccw device fails, resulting in not
operational state, notify the driver and unregister the device in case
the driver dosn't want to keep it.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure that the hardware interruption parameter for a subchannel is
reset when the associated subchannel data structure is freed.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All scsw helper functions are very short and usage of them shouldn't
result in function calls. Therefore we move them to a separate header
file.
Also saves a lot of EXPORT_SYMBOLs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Path verification events occurring for offline devices are currently
ignored. As a result, offline devices are not removed, even though
they might no longer be accessible (for example because the last path
to the device was varied offline). Fix this by scheduling a status
evaluation for the affected subchannel when a path verification event
occurs.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove expensive ktime_get()/ktime_us_delta() functions from the hot
path and use get_clock_monotonic() instead. This elimates seven
function calls and avoids a lot of unnecessary calculations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The timestamp calculation used for s390dbf output is the same in a
private zfcp function and in debug.c. Replace both with a common
inline function.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
dev_set_name tries to allocate memory, so check the return value for
allocation failures. After dev_set_name succeeds, call device_register
as next step to be able to use put_device during error handling.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Don't use kfree directly after device registration started.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The config semaphore is only used as a mutex, so replace it with a
simple mutex.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
So far, zfcp allocated all resources required for FCP
adapters/subchannels when the device was discovered in the ccw_probe
callback. If there are lots of unused FCP subchannels attached to a
system, this is a waste of resources. To alleviate this, defer the
resource allocation to the first call to ccw_set_online. To avoid
disruptions during possible following calls to ccw_set_offline and
then ccw_set_online, keep the adapter resources until the device is
finally being removed via ccw_remove. While doing this, also manage
the zfcp erp thread together with all other adapter resources in
zfcp_adapter_enqueue/dequeue.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The recommendation for a timeout of 2 * R_A_TOV is the same for ct/gs
and els requests, so set it in the common function used for
initializing both request types. Besides, the timer inside zfcp should
only run longer than the timeout set for the channel, so 10 seconds
more should be enough (instead of 60 seconds).
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Switch the creation of the zfcp erp thread from the deprecated
kernel_thread API to the kthread API. This allows also the removal of
some flags in zfcp since the kthread API handles thread creation and
shutdown internally. To allow the usage of the kthread_stop function,
replace the erp ready semaphore with a waitqueue for waiting until erp
actions arrive on the ready queue.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fc_rport structure reserves a reference where a LLD can put
information required in a situation where the fc transport class is
triggering LLD callbacks. The zfcp driver was using this variable
directly which is discouraged. This patch solves this issue by making
this reference unnecessary. In addition the dev_loss_tmo callback is
removed, it is not required: zfcp does not access the fc_rport after
calling fc_remote_port_delete.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update the Fibre Channel related code to use the zfcp_fc prefix.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Extract independent data structures and introduce common _setup and
_destroy routines for QDIO and Fibre Channel related data structures
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Change the dbf data and functions to use the zfcp_dbf prefix
throughout the code. Also change the calls to dbf to use zfcp_dbf
instead of zfcp_adapter.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Don't let the erp wait for gid_pn requests to complete. Instead, queue
the gid_pn work, exit erp and let the finished gid_pn work trigger a
new port reopen.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The zfcp_adapter structure was growing over time to a size of almost
one memory page. To reduce the size of the data structure and to
seperate different layers, put all qdio related data in the new
zfcp_qdio data structure.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Split all qdio related attributes out of zfcp_fsf_req and put it in
new structure.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove the global driver work queue and replace it with a workqueue
local to the adapter. The usage of this workqueue makes this the
correct place for the structure. In addition multiple adapters won't
block each other due to the serialization of the queued work.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The flag ZFCP_REQ_AUTO_CLEANUP was useless as the
ZFCP_STATUS_FSFREQ_CLEANUP flag is there for exactly the same purpose.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove the special case for NO_QTCB requests and optimize the
mempool and cache processing for fsfreqs. Especially use seperate
mempools for the zfcp_fsf_req and zfcp_qtcb structs.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The combination wait_queue/wakeup in conjunction with the flag
ZFCP_STATUS_FSFREQ_COMPLETED to signal the completion of an fsfreq
was not race-safe and can be better solved by a completion.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There is no need for the QDIO layer to have knowledge or do things
wich are done better by the FSF layer and vice versa. Straighten a
few things to improve vividness.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
An adapter shutdown implicitly closes all open ports. Make sure to
mark all WKA ports as offline, not only the directory server. Also
make sure that no pending wka port work is running when the adapter is
being removed.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the FCP channel returns a series of commands with the error
status "test link", zfcp will send a series of ELS ADISC commands.
This is technically no problem, but it is enough to only issue one
test command per remote port. So, track whether a ELS ADISC command is
already pending, and do not send a new one if there is already a
pending command.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Using a bitwise OR to not set anything at all is pointless so remove
the useless statement.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The default trace level is to only trace failed FSF commands. Thus it
is not necessary to collect trace data for most FSF commands, since
it will be thrown away later. Restructure the FSF/HBA trace
infrastructure to first check the trace level in a inline function and
only do the expensive data collection for matching trace levels.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The default trace level is to only trace failed SCSI commands. Thus it
is not necessary to collect trace data for most SCSI commands since it
will be thrown away later. Restructure the SCSI trace infrastructure
to first check the trace level in a inline function and only do the
expensive data collection for matching trace levels.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The struct zfcp_adapter includes everything related to the debug
traces. This introduces dependences between the definitions in
zfcp_def.h and zfcp_dbf.h. Move all debug related data structures to a
new data structure to break those dependencies and manage the debug
data in zfcp_dbf.[hc].
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In certain error scenarios ports, rports are getting attached,
validated and removed from the systems environment. Depending on the
layer this occurs asynchronously. This patch fixes the few races
which existed and ensures all references and cross references are
cleared at the time they're invalid. In addition fc transports
actions are only scheduled when required.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If nothing has been written into the qeth sysfs-attribute layer2,
its value is "-1" meaning "not yet defined". But the value is
displayed as "1" meaning "layer2 selected". The patch changes the
reading of this "-1"-value to "-1" to make clear the layer2-attribute
has not yet been defined.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth displayed an entry in /proc/service_level even when no valid
MCL-string was available (the MCL info is blank). The change is to
create an entry in /proc/service_level only when MCL-string is
non-zero.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear separation of cast-type determination (send path) for layer-2
resp. layer-3. Allowing to have inline functions for qeth layer-
discipline.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the IP address list contains entries (not removed when the device was set
offline) this entries should be registered next time the device is brought online.
In the past this was done implicitly with the device open call but since we wait
in the set IPv4 IPA and the device open common code holds various locks this
does not work any longer.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qeth HiperSockets support now retries sending of packets when the
IBM System z signals a temporary resource shortage (e.g. target
buffer full). The packet is enqueued into the device queue.
After 3 times of unsuccessful send the packet is dropped.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NULL test on block is needed, it should be before the dereference of
the base field.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression E1,E2;
identifier fld;
statement S1,S2;
@@
E1 = E2->fld;
(
if (E1 == NULL) S1 else S2
|
*if (E2 == NULL) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If io_subchannel_initialize_dev fails it will release the only
reference to the ccw device therefore the caller should not
kfree this device since this is done in the release function.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (23 commits)
[SCSI] sd: Avoid sending extended inquiry to legacy devices
[SCSI] libsas: fix wide port hotplug issues
[SCSI] libfc: fix a circular locking warning during sending RRQ
[SCSI] qla4xxx: Remove hiwat code so scsi eh does not get escalated when we can make progress
[SCSI] qla4xxx: Fix srb lookup in qla4xxx_eh_device_reset
[SCSI] qla4xxx: Fix Driver Fault Recovery Completion
[SCSI] qla4xxx: add timeout handler
[SCSI] qla4xxx: Correct Extended Sense Data Errors
[SCSI] libiscsi: disable bh in and abort handler.
[SCSI] zfcp: Fix tracing of request id for abort requests
[SCSI] zfcp: Fix wka port processing
[SCSI] zfcp: avoid double notify in lowmem scenario
[SCSI] zfcp: Add port only once to FC transport class
[SCSI] zfcp: Recover from stalled outbound queue
[SCSI] zfcp: Fix erp escalation procedure
[SCSI] zfcp: Fix logic for physical port close
[SCSI] zfcp: Use -EIO for SBAL allocation failures
[SCSI] zfcp: Use unchained mode for small ct and els requests
[SCSI] zfcp: Use correct flags for zfcp_erp_notify
[SCSI] zfcp: Return -ENOMEM for allocation failures in zfcp_fsf
...
The trace record for SCSI abort requests has a field for the request
id of the request to be aborted. Put the real request id instead of
zero.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Under certain conditions it is possible that a WKA port ist not opened
within the expected timeframe of half a second. In this situation
the WKA port remains in the state OPENING preventing any succeding
request to open the port. This led to unrecoverable remote ports.
Fixing this by always setting an appropriate WKA port status before
leaving the function and removing the timeout value here since it's
not needed here because the general timeout processing would deal
with it if required.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In a LOWMEM condition an ERP notification would have been sent twice
causing an unpredictable behaviour of the ERP.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When calling fc_remote_port_add make sure to not call it again before
fc_remote_port_delete has been called. In other words, ensure to
create a new fc_rport, then delete it, then create a new one again.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Depending on interruptions on some storage systems, the complete
channel can stall which looks like an outbound queue stall to Linux.
When trying to acquire a free SBAL for a non-SCSI command, zfcp waits
for 5 seconds for a free slot to appear. This is the right place to
detect a queue stall: If the wait times out, we assume a stalled queue
and try to recover this.
The overall strategy should be to trigger the erp from specific
events, and not try an overall escalation from one failed port to a
full-blown queue recovery. If we manage to send a command, the status
codes for this command or a timeout will trigger the right follow-on
actions.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If an action fails, retry it until the erp count exceeds the
threshold. If there is something fundamentally wrong, the FSF layer
will trigger a more appropriate action depending on the FSF status
codes.
The followup for successful actions is a different followup than
retrying failed actions, so split the code two functions to make this
clear.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
After closing the port, we want it to be "not open" to consider the
action to be successful.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The ELS ADISC and the GID_PN requests sent from zfcp fit into
unchained FSF requests. Change the FSF allocation logic to use
unchained requests whenever possible where everything fits in one
SBAL. This avoids acquiring more SBALs than necessary, especially
during zfcp recovery when things might be stalled.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
zfcp_erp_notify uses the ZFCP_ERP_STATUS_* flags, so it is
ZFCP_STATUS_ERP_LOWMEM instead of ZFCP_ERP_NOMEM. Signalling
ZFCP_ERP_FAILED is not necessary, the missing d_id will show that the
nameserver did not return the d_id.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When a fsf_req or a qtcb cannot be allocated return -ENOMEM instead of
-EIO.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
req_q_util is not atomic, so the qdio_stat_lock must be held when
reading this variable.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We should not modify the port status after triggering an ERP action
for the port. It is not guaranteed which status is finally active
when the ERP action is performed. This can lead to situations which
are unwanted and hard to debug in case of a failure.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Every time a request is enqueued or there is some work outstanding
from the ap_tasklet, the ap_poll_timer is scheduled again.
Unfortunately it was permanently called. It looked as if it was
started in the past and thus imediately expired.
This has been changed. First it is checked if the hrtimer is already
expired. Then the expiring time is forwarded and the timer restarted.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
remove loop, add some debug data and use get_sense function
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix this:
drivers/s390/char/monreader.c: In function 'mon_open':
drivers/s390/char/monreader.c:323: warning: passing argument 1 of 'dev_set_drvdata' from incompatible pointer type
include/linux/device.h:457: note: expected 'struct device *' but argument is of type 'struct device **'
drivers/s390/char/monreader.c: In function 'monreader_freeze':
drivers/s390/char/monreader.c:466: warning: passing argument 1 of 'dev_get_drvdata' from incompatible pointer type
include/linux/device.h:452: note: expected 'const struct device *' but argument is of type 'struct device **'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define an empty static inline version of sclp_console_pm_event()
to fix the build error below for !SCLP_CONSOLE.
drivers/s390/built-in.o: In function `sclp_rw_pm_event':
sclp_rw.c:(.text+0x12f68): undefined reference to `sclp_console_pm_event'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.
Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To set a dasd online dasd_change_state is called twice. The first
cycle will schedule initial analysis of the device, set the rc to
-EAGAIN and will not touch the device state any more.
The initial analysis will in turn call dasd_change_state to increase
the state to the final DASD_STATE_ONLINE.
If the dasd_change_state on the second thread outruns the other one
both finish with the state set to DASD_STATE_ONLINE and the device
refcount will be decreased by 2.
Fix this by leaving dasd_change_state on rc == -EAGAIN so that the
refcount will always be decreased by 1.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace the remaining direct accesses to the driver_data pointer
with calls to the dev_get_drvdata() and dev_set_drvdata() functions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The stop flags are handled in the generic restore function so the
stop flag is removed also for FBA and DIAG devices.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add Suspend/Resume support to ap bus and zcrypt. All enhancements are
done in the ap bus. No changes in the crypto card specific part are
necessary.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove unneeded sanity checks from do_QDIO since this is the hot path.
Change the type of bufnr and count to unsigned int so the check for the
maximum value works.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is not required to change the state of primed SBALs. Leaving them
primed saves a SQBS instruction under z/VM.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since the adapter interrupt tasklet only schedules the queue tasklets
and contains no code that requires serialization in can be merged
with the adapter interrupt handler. That possibly safes some CPU
cycles.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For devices without QIOASSIST primed SBALS were extracted in a loop.
Remove the loop since get_buf_states can already return more than
one primed SBAL.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The check whether qdio runs under z/VM was incorrect since SIGA-Sync is not
set if the device runs with QIOASSIST. Use MACHINE_IS_VM instead to prevent
polling under z/VM.
Merge qdio_inbound_q_done and tiqdio_is_inbound_q_done.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the adapter interrupt tasklet function to the qdio main code
since all the functions used by the tasklet are located there.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When syncing the sclp console queue, we call del_timer_sync() while holding
the "sclp_con_lock" spinlock. This lock is also taken in the timer function
"sclp_console_timeout". Therefore the sync version of del_timer() cannot be
used here. Because the synchronous deletion of the timer is only needed
in the suspend callback and in that case only one CPU is remaining and
therefore it is not possible that the timer function is running in parallel,
we can safely use del_timer() instead of del_timer_sync().
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic79xx: make driver respect nvram for IU and QAS settings
[SCSI] don't attach ULD to Dell Universal Xport
[SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
[SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
[SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
[SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
[SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
[SCSI] qla2xxx: Resolve a performance issue in interrupt
[SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
[SCSI] nsp_cs: time_out reaches -1
[SCSI] qla2xxx: fix printk format warnings
[SCSI] ncr53c8xx: div reaches -1
[SCSI] compat: don't perform unneeded copy in sg_io code
[SCSI] zfcp: Update FC pass-through support
[SCSI] zfcp: Add FC pass-through support
[SCSI] FC Pass Thru support
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (64 commits)
debugfs: use specified mode to possibly mark files read/write only
debugfs: Fix terminology inconsistency of dir name to mount debugfs filesystem.
xen: remove driver_data direct access of struct device from more drivers
usb: gadget: at91_udc: remove driver_data direct access of struct device
uml: remove driver_data direct access of struct device
block/ps3: remove driver_data direct access of struct device
s390: remove driver_data direct access of struct device
parport: remove driver_data direct access of struct device
parisc: remove driver_data direct access of struct device
of_serial: remove driver_data direct access of struct device
mips: remove driver_data direct access of struct device
ipmi: remove driver_data direct access of struct device
infiniband: ehca: remove driver_data direct access of struct device
ibmvscsi: gadget: at91_udc: remove driver_data direct access of struct device
hvcs: remove driver_data direct access of struct device
xen block: remove driver_data direct access of struct device
thermal: remove driver_data direct access of struct device
scsi: remove driver_data direct access of struct device
pcmcia: remove driver_data direct access of struct device
PCIE: remove driver_data direct access of struct device
...
Manually fix up trivial conflicts due to different direct driver_data
direct access fixups in drivers/block/{ps3disk.c,ps3vram.c}
Introduce the power management callbacks to the 3270 driver. On suspend
the current 3270 view is deactivated and for non-console 3270 device
the release callback is done. This disconnects the current tty /
fullscreen application from the 3270 device. On resume the current
view is reactivated, on the tty you get a fresh login.
If the system panics before the 3270 device has been resumed, the ccw
device for the 3270 console is reactivated with ccw_device_force_console.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Create dummy iucv-device to get control when the system is suspended
and resumed. Server the smsg iucv path on suspend, reestablish the
path on resume.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Patch establishes a dummy netiucv device to make sure iucv is notified
about suspend/resume even if netiucv is the only loaded iucv-exploting
module without any real net_device defined.
The PM freeze callback closes all open netiucv connections. Thus the
corresponding iucv path is removed.
The PM thaw/restore callback re-opens previously closed netiucv
connections.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The SCLP base driver defines a new notifier call back for all upper level SCLP
drivers, like the SCLP console, etc. This guarantees that in suspend first the
upper level drivers are suspended and afterwards the SCLP base driver. For
resume it is the other way round. The SCLP base driver itself registers a
new platform device at the platform bus and gets PM notifications via
the dev_pm_ops.
In suspend, the SCLP base driver switches off the receiver and sender mask
This is done in sclp_deactivate(). After suspend all new requests will be
rejected with -EIO and no more interrupts will be received, because the masks
are switched off. For resume the sender and receiver masks are reset in
the sclp_reactivate() function.
When the SCLP console is suspended, all new messages are cached in the
sclp console buffers. In resume, all the cached messages are written to the
console. In addition to that we have an early resume function that removes
the cached messages from the suspend image.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch implements suspend/hibernation for the vmwatchdog driver. The
pm_notifier_callchain is used to get control on PM events. Since watchdog
operation and suspend cannot work together in a reliable fashion, the open
flag is also used to prevent suspend and open from happening at the same
time.
The watchdog can also be active with no open file descriptor. This patch
adds another flag which is only changed in vmwdt_keep_alive and
vmwdt_disable.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the power management callbacks to the 3215 console. On suspend
the console buffer is flushed to the 3215 device to have an empty console
buffer. Printks done while the 3215 device is suspended are buffered in
the 64K buffer of the 3215 device. If the buffer is full new messages will
push out the oldest messages to make room for the most recent message.
On resume the buffered messages are printed. If the system panics before
the 3215 device is resumed ccw_device_force_console is used to get the
console working again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If something goes wrong in a suspend / resume cycle a ccw based console
if very likely in the suspended state and cannot print anything.
Introduce ccw_device_force_console to force the wake up of the console
device to be able to print the oops message. The console device drivers
should use this function only if the system paniced.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the power management callbacks to the dasd driver. On suspend
the dasd devices are stopped and removed from the focus of alias
management.
On resume they are reinitialized by rereading the device characteristics
and adding the device to the alias management.
In case the device has gone away during suspend it will caught in the
suspend state with stopped flag set to UNRESUMED. After it appears again
the restore function is called again.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Thanks to Sebastian Ott <sebott@linux.vnet.ibm.com> for fixing a few
typos in my original version of this patch.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: linux390@de.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up s390 drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- claw: impossible condition, simply remove it
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (30 commits)
[S390] wire up sys_perf_counter_open
[S390] wire up sys_rt_tgsigqueueinfo
[S390] ftrace: add system call tracer support
[S390] ftrace: add function graph tracer support
[S390] ftrace: add function trace mcount test support
[S390] ftrace: add dynamic ftrace support
[S390] kprobes: use probe_kernel_write
[S390] maccess: arch specific probe_kernel_write() implementation
[S390] maccess: add weak attribute to probe_kernel_write
[S390] profile_tick called twice
[S390] dasd: forward internal errors to dasd_sleep_on caller
[S390] dasd: sync after async probe
[S390] dasd: check_characteristics cleanup
[S390] dasd: no High Performance FICON in 31-bit mode
[S390] dcssblk: revert devt conversion
[S390] qdio: fix access beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
[S390] vmalloc: add vmalloc kernel parameter support
[S390] uaccess: use might_fault() instead of might_sleep()
[S390] 3270: lock dependency fixes
[S390] 3270: do not register with tty_register_device
...
Don't access the block layer request, get the payload length instead
from the FC job. Simplify access to the zfcp_port, only the d_id is
required, if the port is no longer accessed later. This is possible
when the els_handler does not access the port pointer from the ELS
request.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Provide the ability to do fibre channel requests from the userspace to
our zfcp driver. Patch builds upon extension to the fibre channel
tranport class by James Smart and Seokmann Ju. See here
http://marc.info/?l=linux-scsi&m=123808882309133&w=2
Signed-off-by: Sven Schuetz <sven@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (154 commits)
[SCSI] osd: Remove out-of-tree left overs
[SCSI] libosd: Use REQ_QUIET requests.
[SCSI] osduld: use filp_open() when looking up an osd-device
[SCSI] libosd: Define an osd_dev wrapper to retrieve the request_queue
[SCSI] libosd: osd_req_{read,write} takes a length parameter
[SCSI] libosd: Let _osd_req_finalize_data_integrity receive number of out_bytes
[SCSI] libosd: osd_req_{read,write}_kern new API
[SCSI] libosd: Better printout of OSD target system information
[SCSI] libosd: OSD2r05: Attribute definitions
[SCSI] libosd: OSD2r05: Additional command enums
[SCSI] mpt fusion: fix up doc book comments
[SCSI] mpt fusion: Added support for Broadcast primitives Event handling
[SCSI] mpt fusion: Queue full event handling
[SCSI] mpt fusion: RAID device handling and Dual port Raid support is added
[SCSI] mpt fusion: Put IOC into ready state if it not already in ready state
[SCSI] mpt fusion: Code Cleanup patch
[SCSI] mpt fusion: Rescan SAS topology added
[SCSI] mpt fusion: SAS topology scan changes, expander events
[SCSI] mpt fusion: Firmware event implementation using seperate WorkQueue
[SCSI] mpt fusion: rewrite of ioctl_cmds internal generated function
...
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces find_vq/del_vq with find_vqs/del_vqs virtio operations,
and updates all drivers. This is needed for MSI support, because MSI
needs to know the total number of vectors upfront.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ lguest/9p compile fixes)
Add a linked list of all virtqueues for a virtio device: this helps for
debugging and is also needed for upcoming interface change.
Also, add a "name" field for clearer debug messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Function graph tracer support for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a DASD requests is started with dasd_sleep_on and fails, then the
calling function may need to know the reason for the failure.
In cases of hardware errors it can inspect the sense data in the irb,
but when the reason is internal (e.g. start_IO failed) then it needs
a meaningfull return code.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some functions called as a late_initcall depend on completely
initialized devices. Since commit
f3445a1a65 the dasd driver uses the
new async framework and relies on the fact that synchronization is
done in prepare_namespace which is called after the late_initcalls.
Fix this by calling async_synchronize_full at the end of the related
init functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix a broken memset (sizeof pointer vs sizeof the underlying
structure) by cleaning up the involved functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The High Performance FICON feature is not supported in 31-bit mode,
no matter what the various flags say. So we need to check for the
CONFIG_64BIT option as well.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
git commit f331c0296f changed users of
->first_minor to devt. This broke device handling in dcssblk, so that
no additional devices could be added after the first one.
This patch reverts the devt conversion to the previous ->first_minor
handling.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not go beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lockdep found a problem with the lock order of the view lock and the
ccw device lock. raw3270_activate_view/raw3270_deactivate_view first
take the ccw device lock then call the activate/deactivate functions
of the view which take view lock. The update functions of the
con3270/tty3270 view will first take the view lock, then take the
ccw device lock. To fix this the activate/deactivate functions are
changed to avoid taking the view lock by moving the functions calls
that modify the 3270 output buffer to the update function which is
called by a timer.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The tty3270_notifier that calls tty_register_device / tty_unregister_device
is harmful in two ways:
1) the device node that is create is wrong because the minor numbers for
3270 tty start with 1 and tty_notifier passes the minor as index.
2) If 1) is corrected you'll get a warning:
WARNING: at fs/sysfs/dir.c:462 sysfs_add_one+0x4c/0x60()
sysfs: duplicate filename '227:1' can not be created
The 227:1 link is already created by raw3270_create_attributes to refer
to ../../class/tty/tty<devno>. There cannot be two links.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move qdio_perf_stat_inc to the header file so it can be inlined.
Remove unused qdio_perf_stat_dec.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The check for the device status in qdio_establish_handle_irq()
had dead code. Remove the unused code and simplify the error
handling.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some sanity checks in device_ops.c test the output of container_of
macros to be !NULL. Test the input parameters instead.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All definition in cpu.h have to do with cputime accounting. Move
them to cputime.h and remove the header file.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the information about the device and model id in zfcp_ccw. This
requires an additional helper function to check for the privileged
cfdc subchannel, but it allows the removal of the redundant defines
from the zfcp_def header file.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If the destination ID (D_ID) of a remote storage port changed, e.g.
re-plugged cable on the switch in a different switch port, the port
was never (re-)attached within Linux. This patch fixes the broken
mapping between the WWPN and the D_ID.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In rare cases, open port request might timeout, erp calls
zfcp_port_put, port gets dequeued. Now, the late returning (or
dismissed) fsf-port-open calls the fsf_port_open_handler that tries to
reference the port data structure leading to a kernel oops.
Signed-off-by: Martin Petermann <martin.petermann@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add comments where there is a deliberate fall through in switch/case
statements. This makes some code checkers happy and makes it clear
that there is no missing break statement.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
enum dma_data_direction only has the 4 values DMA_BIDIRECTIONAL,
DMA_TO_DEVICE, DMA_FROM_DEVICE and DMA_NONE. No need to have the
default case. While changing this, setup sbtype in one place to make
sparse happy.
The default value of retval is already -EIO, so remove the
additional assignment for these two cases.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
zfcp did always set the queue_depth for SCSI devices to 32, not
allowing to change this. Introduce a kernel parameter zfcp.queue_depth
and the change_queue_depth callback to allow changing the queue_depth
when it is required.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update the newly introduced message for the boxed status to conform to
match the style of s390 and zfcp messages.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The zfcp traces used the fsf_req address in place of the req_id.
Change this to save the correct req_id.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
