u-boot partition size should be 0x80000 (512 KB), not 0x8000 (32 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes USB GPIOs numbers for MPC8569E-MDS boards, plus
according to the latest HW Getting Started Guide (rev 3.3, pilot
boards), USB "POWER" GPIO polarity has changed, it is no longer
inverted.
This patch makes USB Host somewhat work on pilot boards, though
there are still some problems with determining devices speed and
long bulk transfers.
Reported-by: Liu Yu <Yu.Liu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prevent NULL dereference if kmalloc() fails. Also clean up if
of_mdiobus_register() returns an error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI-e addressing was originally patterned of the MPC8548CDS
which has PCI1, PCI2, and PCI-e. Since this board only has
PCI1 and PCI-e, it makes more sense to be similar to the MPC8568MDS
board. This does that by cutting the PCI/PCI-e I/O sizes from
16MB to 8MB and pulling the PCI-e I/O range back to 0xe280_0000
(the hole where PCI2 I/O would have been).
This also fixes a typo where an extra zero made an 8MB range a 128MB
range, removes the hole left by PCI2 from the aliases, and sets the
clocks to match the oscillators that are actually on the board.
With accompanying u-boot updates, PCI-e has been validated with
both a sky2 card (1148:9e00) and an e1000 card (8086:108b).
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RealView PBX board has two 512MB blocks of memory - one at
0x70000000 (with 256MB mirror at 0) and another at 0x20000000. Only the
block at 0x70000000 (or the mirror at 0) may be used for DMA (e.g.
framebuffer). This patch adds the sparsemem definitions to allow the use
of all the memory split as follows:
256MB @ 0x00000000 (ZONE_DMA)
512MB @ 0x20000000 (ZONE_NORMAL)
256MB @ 0x80000000 (ZONE_NORMAL)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The platsmp.c file defines the REALVIEW_SYS_FLAGS* macros which are
already present in platform.h. Just use the latter.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds a realview_fixup() function called during booting to set
up the memory banks. This way there is no need to pass a "mem=" argument
on the kernel command line.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If Linux is running in non-secure mode, this register may have been
already initialised and writing to the control register not allowed.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Patch f598282f51 exposed a problem in
powerpc MSI-X functionality, making network interfaces such as ixgbe
and cxgb3 stop to work when MSI-X is enabled. RX interrupts were not
being generated.
The problem was caused because MSI irq was not being effectively
unmasked after device initialization.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Doing so causes xtime to be negative which crashes the timekeeping
code in funny ways when doing suspend/resume
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I inadvertently left that debug code enabled, causing the number of
contexts to be clamped to 31 which is going to slow things down on
4xx and just plain breaks 8xx
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If TSS we are switching to resides in high memory task switch will fail
since address will be truncated. Windows2k3 does this sometimes when
running with more then 4G
Cc: stable@kernel.org
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We only allocate memory for 32 MCE banks (KVM_MAX_MCE_BANKS) but we
allow user space to fill up to 255 on setup (mcg_cap & 0xff), corrupting
kernel memory. Catch these overflows.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch fixes two issues in the procfs stack information on
x86-64 linux.
The 32 bit loader compat_do_execve did not store stack
start. (this was figured out by Alexey Dobriyan).
The stack information on a x64_64 kernel always shows 0 kbyte
stack usage, because of a missing implementation of the KSTK_ESP
macro which always returned -1.
The new implementation now returns the right value.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1257240160.4889.24.camel@wall-e>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If running in non-secure mode, enabling this register will fault.
Signed-off-by: Tony Thompson <Anthony.Thompson@arm.com>
Acked-by: Srinidhi Kasagar <srinidhikasagar@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Index `ipi_num' is signed, test whether it is negative to
make sure we don't get a negative array element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
- Support bzip2 and lzma kernel compression for m32r.
- Clean up arch/m32r/boot/compressed/misc.c.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Building with --build-id option, .note.gnu.build-id section is added
to vmlinux.bin. But some old buggy binutils creates a huge vmlinux.bin,
and a bootloader fails to boot its zImage as well.
This patch adds a NOTES macro to a linker script vmlinux.ld.S to put
.note.gnu.build-id section into .note section.
Then, the .note section will be removed, because "-R .note" option is
specified in OBJCOPYFLAGS to make a vmlinux.bin binary.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
* 'for-linus' of git://github.com/at91linux/linux-2.6-at91:
at91: at91sam9g45 family: identify several chip versions
avr32: add two new at91 to cpu.h definition
A Xen guest never needs to know about extended topology, and knowing
would just confuse it.
This patch just zeros ebx in leaf 0xb which indicates no topology info,
preventing a crash under Xen on cpus which support this leaf.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
cpu_is_xxx() macros are identifying generic at91sam9g45 chip. This patch adds
the capacity to differentiate Engineering Samples and final lots through the
inclusion of at91_cpu_fully_identify() and the related chip IDs with chip
version field preserved.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Somme common drivers will need those at91 cpu_is_xxx() definitions. As
at91sam9g10 and at91sam9g45 are on the way to linus' tree, here is the patch
that adds those chips to cpu.h in AVR32 architecture.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (38 commits)
MIPS: O32: Fix ppoll
MIPS: Oprofile: Rename cpu_type from godson2 to loongson2
MIPS: Alchemy: Fix hang with high-frequency edge interrupts
MIPS: TXx9: Fix spi-baseclk value
MIPS: bcm63xx: Set the correct BCM3302 CPU name
MIPS: Loongson 2: Set cpu_has_dc_aliases and cpu_icache_snoops_remote_store
MIPS: Avoid potential hazard on Context register
MIPS: Octeon: Use lockless interrupt controller operations when possible.
MIPS: Octeon: Use write_{un,}lock_irq{restore,save} to set irq affinity
MIPS: Set S-cache linesize to 64-bytes for MTI's S-cache
MIPS: SMTC: Avoid queing multiple reschedule IPIs
MIPS: GCMP: Avoid accessing registers when they are not present
MIPS: GIC: Random fixes and enhancements.
MIPS: CMP: Fix memory barriers for correct operation of amon_cpu_start
MIPS: Fix abs.[sd] and neg.[sd] emulation for NaN operands
MIPS: SPRAM: Clean up support code a little
MIPS: 1004K: Enable SPRAM support.
MIPS: Malta: Enable PCI 2.1 compatibility in PIIX4
MIPS: Kconfig: Fix duplicate default value for MIPS_L1_CACHE_SHIFT.
MIPS: MTI: Fix accesses to device registers on MIPS boards
...
* 'fixes-s3c-2632-rc5' of git://git.fluff.org/bjdooks/linux:
ARM: S3C2410: Fix sparse warnings in arch/arm/mach-s3c2410/gpio.c
ARM: S3C2440: mini2440: Fix spare warnings
ARM: S3C24XX: Fix warnings in arch/arm/plat-s3c24xx/gpio.c
ARM: S3C2440: mini2440: Fix missing CONFIG_S3C_DEV_USB_HOST
ARM: S3C24XX: arch/arm/plat-s3c24xx: Move dereference after NULL test
ARM: S3C: Fix adc function exports
ARM: S3C2410: Fix link if CONFIG_S3C2410_IOTIMING is not set
ARM: S3C24XX: Introduce S3C2442B CPU
ARM: S3C24XX: Define a macro to avoid compilation error
ARM: S3C: Add info for supporting circular DMA buffers
ARM: S3C64XX: Set rate of crystal mux
ARM: S3C64XX: Fix S3C64XX_CLKDIV0_ARM_MASK value
Yanmin Zhang reported that SD_PREFER_LOCAL induces an order of
magnitude increase in select_task_rq_fair() overhead while
running heavy wakeup benchmarks (tbench and vmark).
Since SD_BALANCE_WAKE is off at node level, turn SD_PREFER_LOCAL
off as well pending further investigation.
Reported-by: Zhang, Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since interrupt handler is changed to use interrupt priority, we also need
to save and restore these interrupt controller registers in suspend/resume
routine.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Palm Tungsten C keyboard structure has swapped
rows/cols gpio structures and does not work.
This patch fixes it.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Borzoi, Terrier and Akita use the same NAND Flash OOB layout, which
seems to be different from Spitz for some reason. Here is a fix.
When the code was ported to the platform data, the map was applied just
for Akita.
After this patch, Flash works again on Borzoi. Terrier still has a
problem with partition table different from Borzoi (unfixable without
reading of the system configuration in flash) and JFFS2 partitions can
be mounted (with some "Empty flash at ... ends at ..." in the syslog).
Signed-off-by: Stanislav Brabec <utx@penguin.cz>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
Revert "[IA64] fix percpu warnings"
[IA64] fix percpu warnings
[IA64] SMT friendly version of spin_unlock_wait()
[IA64] use printk_once() unaligned.c/io_common.c
[IA64] Require SAL 3.2 in order to do extended config space ops
[IA64] unsigned cannot be less than 0 in sn_hwperf_ioctl()
[IA64] Restore registers in the stack on INIT
[IA64] Re-implement spinaphores using ticket lock concepts
[IA64] Squeeze ticket locks back into 4 bytes.
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: ensure initial page tables are setup for SMP systems
ARM: 5776/1: Check compiler version and EABI support when adding ARM unwind support.
ARM: 5774/1: Fix Realview ARM1176PB board reboot
ARM: Fix errata 411920 workarounds
ARM: Fix sparsemem with SPARSEMEM_EXTREME enabled
ARM: Use GFP_DMA only for masks _less_ than 32-bit
ARM: integrator: allow Integrator to be built with highmem
ARM: Fix signal restart issues with NX and OABI compat
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Make EFI RTC function depend on 32bit again
x86-64: Fix register leak in 32-bit syscall audting
x86: crash_dump: Fix non-pae kdump kernel memory accesses
x86: Side-step lguest problem by only building cmpxchg8b_emu for pre-Pentium
x86: Remove STACKPROTECTOR_ALL
This reverts commit b94b08081f.
genksyms currently cannot handle complicated types for exported
percpu variables. Drop this patch for now as it prevents a
module from being loaded on sn2 systems:
xpc: no symbol version for per_cpu____sn_cnodeid_to_nasid
xpc: Unknown symbol per_cpu____sn_cnodeid_to_nasid
Signed-off-by: Tony Luck <tony.luck@intel.com>
Mapping the same memory using two different attributes (memory
type, shareability, cacheability) is unpredictable. During boot,
we encounter a situation when we're updating the kernel's page
tables which can lead to dirty cache lines existing in the cache
which are subsequently missed. This causes stack corruption,
and therefore a crash.
Therefore, ensure that the shared and cacheability settings
matches the configuration that will be used later; this together
with the restriction in early_cachepolicy() ensures that we won't
create a mismatch during boot.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM unwind is known to compile only with EABI and not-buggy compilers.
The problem is not the unwinding information but the -fno-frame-pointer
option added as a result of !CONFIG_FRAME_POINTER. Now we check the
compiler and raise a #warning in case of wrong compiler.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reboot does not work out of the box on my "Early 2009" Mac mini
(3,1). Detect this machine via DMI as we do for recent MacBooks.
Signed-off-by: Gottfried Haider <gottfried.haider@gmail.com>
Cc: Ozan Çağlayan <ozan@pardus.org.tr>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
sys_ppoll syscall needs to use a compat handler on 64bit kernels with o32
user-space.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unify the naming method between kernel and the user-space oprofile tool.
Because loongson is used instead of godson in most of the places, we agreed
to use loongson instead, which will simplify future maintenance.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The handle_edge_irq() flowhandler disables edge int sources which occur
too fast (i.e. another edge comes in before the irq handler function
had a chance to finish). Currently, the mask_ack() callback does not
ack the edges in hardware, leading to an endless loop in the flowhandler
where it tries to shut up the irq source.
When I rewrote the alchemy IRQ code I wrongly assumed the mask_ack()
callback was only used by the level flowhandler, hence it omitted the
(at the time pointless) edge acks. Turned out I was wrong; so here
is a complete mask_ack implementation for Alchemy IC, which fixes
the above mentioned problem.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For consistency with other BCM63xx SoC set the CPU name to "Broadcom
BCM6338" when actually running on that system.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson 2 does not have dcache aliases when is using 16k pages. and the
And because Loongson 2 doesn't do SMP , cpu_icache_snoops_remote_store does
not matter here.
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
set_saved_sp reads Context register. Avoid reading stale value from
earlier incomplete write.
Issue found and fixed for head.S by Chris Dearman <chris@mips.com>.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some newer Octeon chips have registers that allow lockless operation of
the interrupt controller. Take advantage of them.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the locks are used from interrupt context we need the
irqsave/irqrestore versions of the locking functions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch ensures that the sign bit is always updated for NaN operands.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes the remaining problems introduced by
f197465384 (incorrect access length &
byteswapping in bigendian mode)
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On an SMP system with cache aliases, the following sequence of events may
happen:
1) copy_user_highpage() runs on CPU0, invoking kmap_coherent() to create a
temporary mapping in the fixmap region
2) copy_page() starts on CPU0
3) CPU1 sends CPU0 an IPI asking CPU0 to run local_r4k_flush_cache_page()
4) CPU0 takes the interrupt, interrupting copy_page()
5) local_r4k_flush_cache_page() on CPU0 calls kmap_coherent() again
6) The second invocation of kmap_coherent() on CPU0 tries to use the
same fixmap virtual address that was being used by copy_user_highpage()
7) CPU0 throws a machine check exception for the TLB address conflict
Fixed by creating an extra set of fixmap entries for use in interrupt
handlers. This prevents fixmap VA conflicts between copy_user_highpage()
running in user context, and local_r4k_flush_cache_page() invoked from an
SMP IPI.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch checks if the watchdog enable bit is set in the DCL register
meaning that the hardware watchdog actually works and if so, register the
ar7_wdt platform_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch prepares the board code to register a bcm63xx_wdt
platform_device that we are going to use in a subsequent patch.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the calls to bcm63xx_uart_register in board_bcm963xx.c
and make bcm63xx_uart_register an initfunc. Allows us to remove
bcm63xx_dev_uart.h which was there to make checkpatch.pl happy.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following warning, which becomes an error due to
-Werror to be turned on:
CC arch/mips/alchemy/common/gpiolib-au1000.o
cc1: warnings being treated as errors
arch/mips/alchemy/common/gpiolib-au1000.c: In function 'au1100_gpio2_to_irq':
/home/florian/dev/kernel/linux-queue/arch/mips/include/asm/mach-au1x00/gpio-au1000.h:107: warning: control reaches end of non-void function
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes a lockup on BCM6345 where setting the PLL soft reset bit
will also lock the other blocks including UART. Instead of setting only
the PLL soft reset bit in the software reset register, set this bit but do
not touch the others.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As the commit 3ee4c147 shows, we need to "Add IRQF_TIMER flag for timer
interrupts", Atsushi Nemoto have reported that some other timer interrupts
should be considered, Here it is.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
An o32 aplication passes a 64-bit value in a pair of registers; a 64-bit
kernel expects a 64-bit argument in a single register.
Signed-off-by: Chen Jie <chenj@lemote.com>
Signed-off-by: Hu Hongbing <huhb@lemote.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Along the lines of d6c585a434, add IRQF_TIMER
flag for all timer interrupts This ensures that timer interrupts won't be
disabled on suspend and not threaded for PREEMPT_RT.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
That code is executed with irq disabled already, so, remove the redundant
local_irq_disable() here.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We've silently been relying on the hardware chopping off excess, reserved
ASID bits for no better reason that it saving an instruction. Because we
already have:
#define cpu_asid(cpu, mm) (cpu_context((cpu), (mm)) & ASID_MASK)
in <asm/mmu_context.h>.
We can use a cleanup to avoid writing non-zero bits into the reserved
entryhi bits. This avoid triggering some debugging assertion in the
Cavium simulator.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the fix for proper reboot of Realview ARM1176PB board
when issuing the reboot command. Setting the eighth bit of
control register SYS_RESETCTL to 1 to force a soft reset.
arch_reset() is modified for realview machines to call machine
specific reset function pointers.
Signed-off-by: Philby John <pjohn@in.mvista.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There isn't much else I can do with these. I can find no hardware for any
of them and no users. The code is broken.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Errata 411920 indicates that any "invalidate entire instruction cache"
operation can fail if the right conditions are present. This is not
limited just to those operations in flush.c, but elsewhere. Place the
workaround in the already existing __flush_icache_all() function
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When SPARSEMEM_EXTREME is enabled, memory_present() wants to use bootmem
to allocate data structures. However, we call memory_present() after
declaring memory to bootmem, but before we've reserved areas.
This leads to sparsemem data structures being overwritten later in the
kernel's initialization (when slab initializes.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/ppc64: Use preempt_schedule_irq instead of preempt_schedule
powerpc: Minor cleanup to lib/Kconfig.debug
powerpc: Minor cleanup to sound/ppc/Kconfig
powerpc: Minor cleanup to init/Kconfig
powerpc: Limit memory hotplug support to PPC64 Book-3S machines
powerpc: Limit hugetlbfs support to PPC64 Book-3S machines
powerpc: Fix compile errors found by new ppc64e_defconfig
powerpc: Add a Book-3E 64-bit defconfig
powerpc/booke: Fix xmon single step on PowerPC Book-E
powerpc: Align vDSO base address
powerpc: Fix segment mapping in vdso32
powerpc/iseries: Remove compiler version dependent hack
powerpc/perf_events: Fix priority of MSR HV vs PR bits
powerpc/5200: Update defconfigs
drivers/serial/mpc52xx_uart.c: Use UPIO_MEM rather than SERIAL_IO_MEM
powerpc/boot/dts: drop obsolete 'fsl5200-clocking'
of: Remove nested function
mpc5200: support for the MAN mpc5200 based board mucmc52
mpc5200: support for the MAN mpc5200 based board uc101
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap4: Fix UART4 platform data on omap4
omap4: Allow omap_serial_early_init() for OMAP4430 board
omap3: PM: enable UART3 module wakeups
omap2: Fix console serial port number for n8x0
omap2: Fix detection of n8x0
omap1: Fix DSP public peripherals support for ams-delta
omap1: Fix redundant UARTs pin muxing that can break other hardware support
omap: iommu: fix wrong condition check for SUPERSECTION
omap: SDMA: Fix omap_stop_dma() API for channel linking
omap: Fix omap-keypad by restoring old keypad.h without breaking omap2 boards that use matrix_keypad
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Do less agressive buddy clearing
sched: Disable SD_PREFER_LOCAL for MC/CPU domains
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Set DELIVERY_MODE=4 for vector=NMI_VECTOR in uv_hub_send_ipi()
x86, UV: Fix and clean up bau code to use uv_gpa_to_pnode()
x86: Don't print number of MCE banks for every CPU
x86, UV: Fix information in __uv_hub_info structure
x86: Document linker script ASSERT() quirk
sigp sense only returns the status of a cpu if it is non zero. If the
status of the sensed cpu is all zeros condition code 0 (accpeted) is
set and no status bits are returned.
The current code however assumes that a status was returned and tests
bits in it. This means uninitalized data is accessed with random
results.
Worst case is that the code that checks if cpu is offline on cpu
hotplug assumes that the target cpu is offline while it is still
running. This leads potentially to memory corruption since resources
that are still needed by the target cpu will be freed and could be
resused while still in use.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
According to the architecture a cpu must not necessarily enter stopped
state after completion of a sigp instruction with "stop" order code.
So remove the BUG() statement after self sending sigp stop to avoid
that it ever gets reached.
Also add a sigp busy check to make sure that the order gets delivered.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Offlined cpus still have valid prefix register contents. Dumpers
will store the register contents of a cpu to the location where its
prefix register points to.
For offlined cpus the area (lowcore) has been freed and the dumper
would write the uninteresting contents of the offline cpu to a memory
location which might be in use by some other component and destroy
valueable information.
To fix this set the prefix register of offline cpus to absolute
address zero again. This prevents the current dumpers to write to
random memory locations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix sparse warning in arch/arm/mach-s3c2410/gpio.c due to missing
include of <mach/gpio-fns.h>. Fixes the following warning:
warning: symbol 's3c2410_gpio_irqfilter' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warnings in arch/arm/mach-s3c2440/mach-mini2440.c
due to missing 'static'.
warning: symbol 'mini2440_lcd_cfg' was not declared. Should it be static?
warning: symbol 'mini2440_fb_info' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following warnings from sparse in arch/arm/plat-s3c24xx/gpio.
due to the missing include of <mach/gpio-fns.h>
gpio.c:36:6: warning: symbol 's3c2410_gpio_cfgpin' was not declared. Should it be static?
gpio.c:84:14: warning: symbol 's3c2410_gpio_getcfg' was not declared. Should it be static?
gpio.c:103:6: warning: symbol 's3c2410_gpio_pullup' was not declared. Should it be static?
gpio.c:125:5: warning: symbol 's3c2410_gpio_getpull' was not declared. Should it be static?
gpio.c:138:6: warning: symbol 's3c2410_gpio_setpin' was not declared. Should it be static?
gpio.c:157:14: warning: symbol 's3c2410_gpio_getpin' was not declared. Should it be static?
gpio.c:184:5: warning: symbol 's3c2410_gpio_getirq' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix missing select of S3C_DEV_USB_HOST when building for mini2440
only. Fixes the following error:
built-in.o: undefined reference to `s3c_device_usb`
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the NULL test on buf is needed, then the dereference should be after the
NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the export of s3c_adc_read.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
[ben-linux@fluff.org: remove unexport of s3c_adc_start, needed for ts]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the link errors if cpu-frequency support is enabled on s3c2410 systems
but there is no CONFIG_S3C2410_IOTIMING set. Fix this by ensuring the
relevant symbols are defined NULL if the code is not being built in.
Fixes the following error:
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_get'
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_set'
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_calc'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the S3C2442B CPU ID to aid support the Openmoko GTA02 / Freerunner.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: edit description for clarity and S3C2442B as uppercase]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define a macro to avoid the following error during kernel build process
for platforms other than s3c2410:
arch/arm/plat-s3c24xx/cpu.c:84: error: ‘s3c2410a_init’ undeclared here (not in a function)
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C64XX DMA implementation will work a lot better with the ability
to enqueue circular buffers as the hardware can do it's own linked-list
management.
Add a function s3c_dma_has_circular() to show that the system can do this
and a flag for the channel.
Update the s3c24xx/s3c64xx I2S DMA code to deal with this.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Mark Brown <broonie@@opensource.wolfsonmicro.com>
The function iommu_feature_disable is required on system
shutdown to disable the IOMMU but it is marked as __init.
This may result in a panic if the memory is reused. This
patch fixes this bug.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
xen_setup_stackprotector() ends up trying to set page protections,
so we need to have vm_mmu_ops set up before trying to do so.
Failing to do so causes an early boot crash.
[ Impact: Fix early crash under Xen. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The EFI RTC functions are only available on 32 bit. commit 7bd867df
(x86: Move get/set_wallclock to x86_platform_ops) removed the 32bit
dependency which leads to boot crashes on 64bit EFI systems.
Add the dependency back.
Solves: http://bugzilla.kernel.org/show_bug.cgi?id=14466
Tested-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Feng Tang <feng.tang@intel.com>
LKML-Reference: <20091020125402.028d66d5@feng-desktop>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Based on an original patch by Valentine Barshak <vbarshak@ru.mvista.com>
Use preempt_schedule_irq to prevent infinite irq-entry and
eventual stack overflow problems with fast-paced IRQ sources.
This kind of problems has been observed on the PASemi Electra IDE
controller. We have to make sure we are soft-disabled before calling
preempt_schedule_irq and hard disable interrupts after that
to avoid unrecoverable exceptions.
This patch also moves the "clrrdi r9,r1,THREAD_SHIFT" out of
the #ifdef CONFIG_PPC_BOOK3E scope, since r9 is clobbered
and has to be restored in both cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the following 3 issues:
arch/powerpc/kernel/process.c: In function 'arch_randomize_brk':
arch/powerpc/kernel/process.c:1183: error: 'mmu_highuser_ssize' undeclared (first use in this function)
arch/powerpc/kernel/process.c:1183: error: (Each undeclared identifier is reported only once
arch/powerpc/kernel/process.c:1183: error: for each function it appears in.)
arch/powerpc/kernel/process.c:1183: error: 'MMU_SEGSIZE_1T' undeclared (first use in this function)
In file included from arch/powerpc/kernel/setup_64.c:60:
arch/powerpc/include/asm/mmu-hash64.h:132: error: redefinition of 'struct mmu_psize_def'
arch/powerpc/include/asm/mmu-hash64.h:159: error: expected identifier or '(' before numeric constant
arch/powerpc/include/asm/mmu-hash64.h:396: error: conflicting types for 'mm_context_t'
arch/powerpc/include/asm/mmu-book3e.h:184: error: previous declaration of 'mm_context_t' was here
cc1: warnings being treated as errors
arch/powerpc/kernel/pci_64.c: In function 'pcibios_unmap_io_space':
arch/powerpc/kernel/pci_64.c💯 error: unused variable 'res'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This defconfig's purpose at this time is to help catch compile errors
between Book-3S and Book-3E support in ppc64. It is based on the
ppc64_defconfig with some things disabled that we dont support on
Book-3E right now (hugetlbfs, slices, etc.)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Prior to the arch/ppc -> arch/powerpc transition, xmon had support for single
stepping on 4xx boards. The functionality was lost when arch/ppc was removed.
This patch restores single step support for 44x boards, and Book-E in general.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ABI specifies a 64K alignment, we need to map the vDSO accordingly
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Due to missing segment assignments the .text section was put in the NOTES
segment (and marked as NOTE section), and the .got was put in the DYNAMIC
segment.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The creation of the flattened device tree depended on the compiler
putting the constant strings for an object in a section with a
particular name. This was changed with recent compilers. Do this
explicitly instead.
Without this patch, iseries kernels may silently not boot when built with
some compilers.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The architecture defines that if MSR PR is set we are in problem state
irrespective of the HV bit. This fixes perf events to reflect this.
Also, on bare metal systems, samples taken in Linux will now be reported
as kernel rather than hypervisor.
Signed-off-by: Michael Neuling <mikey@neuling.org>
CC: paulus@samba.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The hugetlb dependencies presently depend on SUPERH && MMU while the
hugetlb page size definitions depend on CPU_SH4 or CPU_SH5. This
unfortunately allows SH-3 + MMU configurations to enable hugetlbfs
without a corresponding HPAGE_SHIFT definition, resulting in the build
blowing up.
As SH-3 doesn't support variable page sizes, we tighten up the
dependenies a bit to prevent hugetlbfs from being enabled. These days
we also have a shiny new SYS_SUPPORTS_HUGETLBFS, so switch to using
that rather than adding to the list of corner cases in fs/Kconfig.
Reported-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current code assumes that the external clock mux will be set to
the crystal. Set this up explicitly within the clock API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the values of S3C6400_CLKDIV0_ARM_MASK and S3C6410_CLKDIV0_ARM_MASK.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Restoring %ebp after the call to audit_syscall_exit() is not
only unnecessary (because the register didn't get clobbered),
but in the sysenter case wasn't even doing the right thing: It
loaded %ebp from a location below the top of stack (RBP <
ARGOFFSET), i.e. arbitrary kernel data got passed back to user
mode in the register.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: <stable@kernel.org>
LKML-Reference: <4AE5CC4D020000780001BD13@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Non-PAE 32-bit dump kernels may wrap an address around 4G and
poke unwanted space. ptes there are 32-bit long, and since
pfn << PAGE_SIZE may exceed this limit, high pfn bits are
cropped and wrong address mapped by kmap_atomic_pfn in
copy_oldmem_page.
Don't allow this behavior in non-PAE kdump kernels by checking
pfns passed into copy_oldmem_page. In the case of failure,
userspace process gets EFAULT.
[v2]
- fix comments
- move ifdefs inside the function
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Paul Mundt <lethal@linux-sh.org>
LKML-Reference: <1256551903-30567-1-git-send-email-jirislaby@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 79e1dd05d1 "x86: Provide an alternative() based
cmpxchg64()" broke lguest, even on systems which have cmpxchg8b
support. The emulation code gets used until alternatives get
run, but it contains native instructions, not their paravirt
alternatives.
The simplest fix is to turn this code off except for 386 and 486
builds.
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: lguest@ozlabs.org
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <200910261426.05769.rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add an uImage.bin target to allow uncompressed uImages.
Useful for boards with busted u-boot decompression like
the rsk7203 on my desk.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When CONFIG_FUNCTION_GRAPH_TRACER is enabled the function graph tracer
may patch return addresses on the stack with the address of
return_to_handler(). This really confuses the DWARF unwinder because it
will try find the caller of return_to_handler(), not the caller of the
real return address.
So teach the DWARF unwinder how to find the real return address whenever
it encounters return_to_handler().
This patch does not cope very well when multiple return addresses on the
stack have been patched. To make it work properly it would require state
to track how many return_to_handler()'s have been seen so that we'd know
where to look in current->curr_ret_stack[]. So for now, instead of
trying to handle this, just moan if more than one return address on the
stack has been patched.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds an __irq_entry annotation for do_IRQ() so that the IRQ
annotation in the function graph tracer works as advertized. We already
have the IRQENTRY section wired up, so this is just a trivial addition
to actually make use of it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We were using GFP_DMA for masks other than 0xffffffff, which is
wrong when some masks are initialized to 0xffffffffffffffff.
This caused such masks to obtain memory from the precious DMA
pool.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes Integrator builds with highmem enabled; we need to
translate from 'struct page' to a DMA address, and this is not
possible without __pfn_to_bus().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The signal restarting code was placed on the user stack when OABI
compatibility is enabled. Unfortunately, with an EABI NX executable,
this results in an attempt to run code from the non-executable stack,
which segfaults the application.
Fix this by placing the code in the vectors page, along side the
signal return code, and directing the application to that code.
Reported-by: saeed bishara <saeed.bishara@gmail.com>
Tested-by: saeed bishara <saeed.bishara@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
STACKPROTECTOR_ALL has a really high overhead (runtime and stack
footprint) and is not really worth it protection wise (the
normal STACKPROTECTOR is in effect for all functions with
buffers already), so lets just remove the option entirely.
Reported-by: Dave Jones <davej@redhat.com>
Reported-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Eric Sandeen <sandeen@redhat.com>
LKML-Reference: <20091023073101.3dce4ebb@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch removes the unnecessary UART4 platform which is under
data is wrong because of this
There is a separate platform structure for UART4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-By: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables omap_serial_early_init() function for OMAP4430
SDP. Without this the bootup would throw oops in omap_serial_init().
Note that the ifndef CONFIG_ARCH_OMAP4 is split into two sections
to enable omap_serial_early_init(). This ifndef cannot be removed
until omap4 clock framework is implemented.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-By: Tony Lindgren <tony@atomide.com>
Reviewed-By: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART3 is in the PER powerdomain. If PER goes idle/inactive
independently of CORE, for UART3 to wakeup it must have its wakeup
enable bits setup in PM_WKEN_PER. This patch enables these bits.
The reason it works when PER and CORE work together is because when
CORE goes inactive/retention, the IOPAD wakeups are enabled and
trigger UART3 wakeup.
Without this patch, when the UART inactivity timer fires for UART3,
its clocks are disabled and it's unable to wakeup so will be unusable
until PER is awoken by another source.
Another way of testing is by keeping CORE on during suspend but
allowing PER to hit retention
# echo 3 > /debug/pm_debug/core_pwrdm/suspend
then enter suspend
# echo mem > /sys/power/state
Without this patch, UART3 will be unable to wakeup the system.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the recent changes omap serial ports match the physical
numbering like they should. Fix the kernel CMDLINE accordingly
so console works.
Signed-off-by: Tony Lindgren <tony@atomide.com>
DSP public peripherals used to work on OMAP1510 based (or all OMAP1 class?)
machines as long as old dspgateway code were present in the l-o tree. For
several months it is no longer included, breaking support for McBSP1 based
audio on Amstrad Delta, for example.
This patch, derived from the old dspgateway code, corrects the problem for the
board by simply taking the DSP out of reset state, I guess. That way, things
should not break when a new dsp code is added to the tree, and the change can
be reverted then.
If there are any reports on McBSP1 or other DSP public peripherals not working
for other OMAP1 machines (I've not heard of any for now), I can prepare a more
general patch providing an extra include file with a helper function defined.
Created and tested against linux-2.6.32-rc5
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 15ac408ee5 removed enabled_uart
and OMAP_TAG_UART. This works for mach-omap2, but causes issues on
mach-omap1 for some boards as the mach-omap1 serial.c was muxing
pins based on the enabled_uart flag for 15xx.
Fix this by muxing pins in board-*.c files for the 15xx boards for
the uart ports that had enabled_uart flag set before the commit
above.
Tested on Amsdtrad Delta only.
Note that in the future we should add support for powering down
the uarts with a timer like mach-omap2/serial.c does. Otherwise
the enabled uarts will be blocking retention-while-idle.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A bit (2 << 0) is set both on SECTION and SUPERSECTION. To identify
SUPERSECTION correctly, other bits should be compared too.
Reported-by: "Srinivas Pulukuru" <srinivas.pulukuru@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
