According to gpio-samsung.c, this patch updates the name of
regarding Samsung GPIO. Basically the samsung_xxx prefix is
used in gpio-samsung.c instead of s3c_xxx, because unified
name can reduce its complexity.
Note: some s3c_xxx stil remains because it is used widely.
It will be updated next time.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for Samsung GPIOs with one gpio driver
and removes old GPIO drivers which are drivers/gpio-s3c24xx.c,
gpio-s3c64xx.c, gpio-s5p64x0.c, gpio-s5pc100.c, gpio-s5pv210.c,
gpio-exynos4.c, gpio-plat-samsung.c, plat-samsung/gpio-config.c
and gpio.c to support each Samsung SoCs before. Because the
gpio-samsung.c can replace old Samsung GPIO drivers.
Basically, the gpio-samsung.c has been made by their merging
and removing duplicated definitions.
Note: gpio-samsung.c includes some SoC dependent codes and it
will be replaced next time.
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: squash the removing and adding patches]
[kgene.kim@samsung.com: fixes bug during to register of gpio_chips]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Remove duplicate "return" statement
drm/nv04/crtc: Bail out if FB is not bound to crtc
drm/nouveau: fix nv04_sgdma_bind on non-"4kB pages" archs
drm/nouveau: properly handle allocation failure in nouveau_sgdma_populate
drm/nouveau: fix oops on pre-semaphore hardware
drm/nv50/crtc: Bail out if FB is not bound to crtc
drm/radeon/kms: fix DP detect and EDID fetch for DP bridges
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
ARM: CSR: add missing sentinels to of_device_id tables
ARM: cns3xxx: Fix newly introduced warnings in the PCIe code
ARM: cns3xxx: Fix compile error caused by hardware.h removed
ARM: davinci: fix cache flush build error
ARM: davinci: correct MDSTAT_STATE_MASK
ARM: davinci: da850 EVM: read mac address from SPI flash
OMAP: omap_device: fix !CONFIG_SUSPEND case in _noirq handlers
OMAP2430: hwmod: musb: add missing terminator to omap2430_usbhsotg_addrs[]
OMAP3: clock: indicate that gpt12_fck and wdt1_fck are in the WKUP clockdomain
OMAP4: clock: fix compile warning
OMAP4: clock: re-enable previous clockdomain enable/disable sequence
OMAP: clockdomain: Wait for powerdomain to be ON when using clockdomain force wakeup
OMAP: powerdomains: Make all powerdomain target states as ON at init
The LTTng 2.0 kernel tracer (stand-alone module package, available at
http://lttng.org) uses the 0xF6 ioctl range for tracer control and
transport operations.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://github.com/chrismason/linux:
Btrfs: add dummy extent if dst offset excceeds file end in
Btrfs: calc file extent num_bytes correctly in file clone
btrfs: xattr: fix attribute removal
Btrfs: fix wrong nbytes information of the inode
Btrfs: fix the file extent gap when doing direct IO
Btrfs: fix unclosed transaction handle in btrfs_cont_expand
Btrfs: fix misuse of trans block rsv
Btrfs: reset to appropriate block rsv after orphan operations
Btrfs: skip locking if searching the commit root in csum lookup
btrfs: fix warning in iput for bad-inode
Btrfs: fix an oops when deleting snapshots
Commit 37fb3a30b4 ("fuse: fix flock") added in 3.1-rc4 caused flock() to
fail with ENOSYS with the kernel ABI version 7.16 or earlier.
Fix by falling back to testing FUSE_POSIX_LOCKS for ABI versions 7.16
and earlier.
Reported-by: Martin Ziegler <ziegler@email.mathematik.uni-freiburg.de>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Martin Ziegler <ziegler@email.mathematik.uni-freiburg.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
You can see there's no file extent with range [0, 4096]. Check this by
btrfsck:
# btrfsck /dev/sda7
root 5 inode 258 errors 100
...
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
An attribute is not removed by 'setfattr -x attr file' and remains
visible in attr list. This makes xfstests/062 pass again.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
If we write some data into the data hole of the file(no preallocation for this
hole), Btrfs will allocate some disk space, and update nbytes of the inode, but
the other element--disk_i_size needn't be updated. At this condition, we must
update inode metadata though disk_i_size is not changed(btrfs_ordered_update_i_size()
return 1).
# mkfs.btrfs /dev/sdb1
# mount /dev/sdb1 /mnt
# touch /mnt/a
# truncate -s 856002 /mnt/a
# dd if=/dev/zero of=/mnt/a bs=4K count=1 conv=nocreat,notrunc
# umount /mnt
# btrfsck /dev/sdb1
root 5 inode 257 errors 400
found 32768 bytes used err is 1
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When we write some data to the place that is beyond the end of the file
in direct I/O mode, a data hole will be created. And Btrfs should insert
a file extent item that point to this hole into the fs tree. But unfortunately
Btrfs forgets doing it.
The following is a simple way to reproduce it:
# mkfs.btrfs /dev/sdc2
# mount /dev/sdc2 /test4
# touch /test4/a
# dd if=/dev/zero of=/test4/a seek=8 count=1 bs=4K oflag=direct conv=nocreat,notrunc
# umount /test4
# btrfsck /dev/sdc2
root 5 inode 257 errors 100
Reported-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Tested-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The function - btrfs_cont_expand() forgot to close the transaction handle before
it jump out the while loop. Fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
At the beginning of create_pending_snapshot, trans->block_rsv is set
to pending->block_rsv and is used for snapshot things, however, when
it is done, we do not recover it as will.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
While truncating free space cache, we forget to change trans->block_rsv
back to the original one, but leave it with the orphan_block_rsv, and
then with option inode_cache enable, it leads to countless warnings of
btrfs_alloc_free_block and btrfs_orphan_commit_root:
WARNING: at fs/btrfs/extent-tree.c:5711 btrfs_alloc_free_block+0x180/0x350 [btrfs]()
...
WARNING: at fs/btrfs/inode.c:2193 btrfs_orphan_commit_root+0xb0/0xc0 [btrfs]()
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
It's not enough to just search the commit root, since we could be cow'ing the
very block we need to search through, which would mean that its locked and we'll
still deadlock. So use path->skip_locking as well. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
iput() shouldn't be called for inodes in I_NEW state.
We need to mark inode as constructed first.
WARNING: at fs/inode.c:1309 iput+0x20b/0x210()
Call Trace:
[<ffffffff8103e7ba>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8103e805>] warn_slowpath_null+0x15/0x20
[<ffffffff810eaf0b>] iput+0x20b/0x210
[<ffffffff811b96fb>] btrfs_iget+0x1eb/0x4a0
[<ffffffff811c3ad6>] btrfs_run_defrag_inodes+0x136/0x210
[<ffffffff811ad55f>] cleaner_kthread+0x17f/0x1a0
[<ffffffff81035b7d>] ? sub_preempt_count+0x9d/0xd0
[<ffffffff811ad3e0>] ? transaction_kthread+0x280/0x280
[<ffffffff8105af86>] kthread+0x96/0xa0
[<ffffffff814336d4>] kernel_thread_helper+0x4/0x10
[<ffffffff8105aef0>] ? kthread_worker_fn+0x190/0x190
[<ffffffff814336d0>] ? gs_change+0xb/0xb
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
CC: Konstantin Khlebnikov <khlebnikov@openvz.org>
Tested-by: David Sterba <dsterba@suse.cz>
CC: Josef Bacik <josef@redhat.com>
CC: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We can reproduce this oops via the following steps:
$ mkfs.btrfs /dev/sdb7
$ mount /dev/sdb7 /mnt/btrfs
$ for ((i=0; i<3; i++)); do btrfs sub snap /mnt/btrfs /mnt/btrfs/s_$i; done
$ rm -fr /mnt/btrfs/*
$ rm -fr /mnt/btrfs/*
then we'll get
------------[ cut here ]------------
kernel BUG at fs/btrfs/inode.c:2264!
[...]
Call Trace:
[<ffffffffa05578c7>] btrfs_rmdir+0xf7/0x1b0 [btrfs]
[<ffffffff81150b95>] vfs_rmdir+0xa5/0xf0
[<ffffffff81153cc3>] do_rmdir+0x123/0x140
[<ffffffff81145ac7>] ? fput+0x197/0x260
[<ffffffff810aecff>] ? audit_syscall_entry+0x1bf/0x1f0
[<ffffffff81153d0d>] sys_unlinkat+0x2d/0x40
[<ffffffff8147896b>] system_call_fastpath+0x16/0x1b
RIP [<ffffffffa054f7b9>] btrfs_orphan_add+0x179/0x1a0 [btrfs]
When it comes to btrfs_lookup_dentry, we may set a snapshot's inode->i_ino
to BTRFS_EMPTY_SUBVOL_DIR_OBJECTID instead of BTRFS_FIRST_FREE_OBJECTID,
while the snapshot's location.objectid remains unchanged.
However, btrfs_ino() does not take this into account, and returns a wrong ino,
and causes the oops.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
dvb_usb_device_init calls the frontend_attach method of this driver which
uses vp7045_usb_ob. In order to have a buffer ready in vp7045_usb_op, it has to
be allocated before that happens.
Luckily we can use the whole private data as the buffer as it gets separately
allocated on the heap via kzalloc in dvb_usb_device_init and is thus apt for
use via usb_control_msg.
This fixes a
BUG: unable to handle kernel paging request at 0000000000001e78
reported by Tino Keitel and diagnosed by Dan Carpenter.
Cc: stable@kernel.org # For v3.0 and upper
Tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The nuvoton-cir driver was storing up consecutive pulse-pulse and
space-space samples internally, for no good reason, since
ir_raw_event_store_with_filter() already merges back to back like
samples types for us. This should also fix a regression introduced late
in 3.0 that related to a timeout change, which actually becomes correct
when coupled with this change. Tested with RC6 and RC5 on my own
nuvoton-cir hardware atop vanilla 3.0.0, after verifying quirky
behavior in 3.0 due to the timeout change.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the unlikely case that pci_find_bus() should return NULL
viacam_serial_is_enabled() is going to dereference a NULL pointer and
blow up. Better safe than sorry, so be defensive and check the
pointer.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed missing ids of the codec controls description in the controls.xml file.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The images are clearer with a lower bridge clock.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced by git commit 0e4d413af1, giving very dark images.
Signed-off-by: Luiz Carlos Ramos <lramos.prof@yahoo.com.br>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The list of the webcams which have LED inversion was rebuild scanning
ms-win .inf files.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'!' has higher precedence than '&' so we need parenthesis here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the initial architecture submission, not all of the DMA ops were
implemented. This patch adds the *map_page and *map_sg variants of the
DMA mapping ops.
This patch is currently of interest mainly to some drivers that haven't
been submitted upstream yet.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
The of_device_id tables used for matching should be terminated with
empty sentinel values.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Barry Song <baohua.song@csr.com>
When CONFIG_NET is disabled, SCSI_QLA_ISCSI selects SCSI_ISCSI_ATTRS,
which uses network interfaces, so the build fails with multiple errors:
warning: (ISCSI_TCP && SCSI_CXGB3_ISCSI && SCSI_CXGB4_ISCSI && SCSI_QLA_ISCSI && INFINIBAND_ISER) selects SCSI_ISCSI_ATTRS which has unmet direct dependencies (SCSI && NET)
ERROR: "skb_trim" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_create" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_release" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
...
so make SCSI_QLA_ISCSI also depend on NET to prevent the build errors.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: iscsi-driver@qlogic.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7088/1: entry: fix wrong parameter name used in do_thumb_abort
ARM: 7080/1: l2x0: make sure I&D are not locked down on init
ARM: 7081/1: mach-integrator: fix the clocksource
NET: am79c961: fix race in link status code
ARM: 7067/1: mm: keep significant bits in pfn_valid
Commit be020f8618, "ARM: entry: abort-macro: specify registers to be
used for macros", while replacing register numbers with macro parameter
names, mismatched the name used for r1. For me, this resulted in user
space built for EABI with -march=armv4t -mtune=arm920t -mthumb-interwork
-mthumb broken on my OMAP1510 based Amstrad Delta (old ABI and no thumb
still worked for me though).
Fix this by using correct parameter name fsr instead of mismatched psr,
used by callers for another purpose.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since backlight_types[] isn't modified, let's declare it const. That
was probably the intention of the author of commit bb7ca747f8
("backlight: add backlight type"), via which the "const char const *"
construct was introduced. The duplicate const was detected by sparse.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://neil.brown.name/md:
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
md/raid1,10: Remove use-after-free bug in make_request.
md/raid10: unify handling of write completion.
Avoid dereferencing a 'request_queue' after last close.
0.90 metadata uses an unsigned 32bit number to count the number of
kilobytes used from each device.
This should allow up to 4TB per device.
However we multiply this by 2 (to get sectors) before casting to a
larger type, so sizes above 2TB get truncated.
Also we allow rdev->sectors to be larger than 4TB, so it is possible
for the array to be resized larger than the metadata can handle.
So make sure rdev->sectors never exceeds 4TB when 0.90 metadata is in
used.
Also the sanity check at the end of super_90_load should include level
1 as it used ->size too. (RAID0 and Linear don't use ->size at all).
Reported-by: Pim Zandbergen <P.Zandbergen@macroscoop.nl>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
A single request to RAID1 or RAID10 might result in multiple
requests if there are known bad blocks that need to be avoided.
To detect if we need to submit another write request we test:
if (sectors_handled < (bio->bi_size >> 9)) {
However this is after we call **_write_done() so the 'bio' no longer
belongs to us - the writes could have completed and the bio freed.
So move the **_write_done call until after the test against
bio->bi_size.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=41862
Reported-by: Bruno Wolff III <bruno@wolff.to>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: NeilBrown <neilb@suse.de>
A write can complete at two different places:
1/ when the last member-device write completes, through
raid10_end_write_request
2/ in make_request() when we remove the initial bias from ->remaining.
These two should do exactly the same thing and the comment says they
do, but they don't.
So factor the correct code out into a function and call it in both
places. This makes the code much more similar to RAID1.
The difference is only significant if there is an error, and they
usually take a while, so it is unlikely that there will be an error
already when make_request is completing, so this is unlikely to cause
real problems.
Signed-off-by: NeilBrown <neilb@suse.de>
On the last close of an 'md' device which as been stopped, the device
is destroyed and in particular the request_queue is freed. The free
is done in a separate thread so it might happen a short time later.
__blkdev_put calls bdev_inode_switch_bdi *after* ->release has been
called.
Since commit f758eeabeb
bdev_inode_switch_bdi will dereference the 'old' bdi, which lives
inside a request_queue, to get a spin lock. This causes the last
close on an md device to sometime take a spin_lock which lives in
freed memory - which results in an oops.
So move the called to bdev_inode_switch_bdi before the call to
->release.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has
massive negative ramifications on some devices. Without knowing which
devices have this issue, do not modify from the default value when
walking the PCI-E bus in pcie_bus_safe mode. Also, make pcie_bus_safe
the default procedure.
Tested-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Simon Kirby <sim@hostway.ca>
Tested-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-and-tested-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
References: https://bugzilla.kernel.org/show_bug.cgi?id=42162
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b03e7495a8 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.
To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://dev.laptop.org/users/cjb/mmc:
mmc: sdhci-s3c: Fix mmc card I/O problem
mmc: sd: UHS-I bus speed should be set last in UHS initialization
mmc: sdhi: initialise mmc_data->flags before use
mmc: core: use non-reentrant workqueue for clock gating
mmc: core: prevent aggressive clock gating racing with ios updates
mmc: rename mmc_host_clk_{ungate|gate} to mmc_host_clk_{hold|release}
mmc: sdhci-esdhc-imx: add missing inclusion of linux/module.h
