Currently the driver only exposes the raw counts. As we
have the regulator voltage and the maximum value (stored in
the data mask), we can trivially produce a scaling fraction
of voltage / max value.
This assumes that the regulator voltage is in fact the max
voltage, which appears to be the case for all mainline dts
and cross referenced with the public Exynos4412 and S5PV210
datasheets.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is clear that we transition to INDIO_DIRECT_MODE when disabling the
buffer(s) and it is also clear that we transition from INDIO_DIRECT_MODE
when enabling the buffer(s). So leaving the currentmode field
INDIO_DIRECT_MODE until after the preenable() callback and updating it to
INDIO_DIRECT_MODE before the postdisable() callback doesn't add additional
value. On the other hand some drivers will need to perform different
actions depending on which mode the device is going to operate in/was
operating in.
Moving the update of currentmode before preenable() and after postdisable()
enables us to have drivers which perform mode dependent actions in those
callbacks.
Note, was originally not intended as such, but fixes an issue introduced
in the at91-sama5d2 adc driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Fixes: 065056cb0d ("iio: at91-sama5d2_adc: split at91_adc_current_chan_is_touch() helper")
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
This also changes some internal functions to pass the pointer to the
state-struct vs a ref to indio_dev just to access the state-struct again.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As part of the general cleanup of indio_dev->mlock, this change replaces
it with a local lock on the device's state structure.
This also changes some internal functions to pass the pointer to the
state-struct vs a ref to indio_dev just to access the state-struct again.
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma150/smb380 are very similar to the bma023 but have a temperature
channel as well.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma180 driver is being extended to support the bma150.
Its temperature channel is unsigned so the center_temp naming
no longer makes.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma023 chip is similar enough to the bma180 and bma25x that the
same driver can support all of them. The biggest differences are
the lack of a temperature channel and no low power but still working
mode.
The bma150 is a close relative of the bma023, but it does have a
temperature channel so support is not added for it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma180 and related chips should have two regulators attached to
them. The IIO driver currently uses them, document them here as
well.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma023, bma150, and smb380 are in the same family as the bma180
and support is being added to the bma180 IIO driver for them.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma180 IIO driver is being extended for support for the chips
support by input's bma150 driver (bma023, bma150, smb380). Don't
allow both drivers to be enabled simultaneously as they're for the
same hardware.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some variants of the bma180 (eg bma023) have different reset
values. In preparation for adding support for them, factor
out the reset value into the chip specific data.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usual mixed back but with a few subsystem wide or device type
wide cleanups.
New device support
* adis16475
- New driver supporting adis16470, adis16475, adis16477, adis16465,
adis16467, adis16500, adis16505 and adis16507.
Includes some rework of the adis library to simplify using it
for this new driver.
* ak8974
- Add support for Alps hscdt008a. ID only. Related patches add support
for scale.
* atlas-sensor
- Add support for RTD-SM OEM temperature sensor.
* cm32181
- Add support for CM3218 including support for SMBUS alert via
ACPI resources.
* ltc2632
- Add support for ltc2634-12/10/8 DACS including handling per
device type numbers of channels.
Major Features
* cm32181
- ACPI bindings including parsing CPM0 and CPM1 custom ACPI tables.
Includes minor tidy ups and fixes.
* vcnl4000
- Add event support
- Add buffered data capture support
- Add control of sampling frequency
Cleanups and minor fixes.
* core
- Trivial rework of iio_device_alloc to use an early return and
improve readability.
- Precursors to addition of multiple buffer support. So far
minor refactoring.
* subsystem wide
- Use get_unaligned_be24 slightly improve readability over open
coding it.
* adis drivers
- Use iio_get_debugfs_dentry access function.
* bh1780, cm32181, cm3232, gp2ap02a00f, opt3001, st_uvis25, vl6180,
dmard06, kxsd9
- Drop use of of_match_ptr to allow ACPI based probing via PRP0001.
Part of clear out of this to avoid cut and paste into new drivers.
* ad5592r, ad5593r
- Fix typos
* ad5933
- Use managed interfaces to automate error handling and remove.
* ak8974
- Fix wrong number of 'real bits' for buffered data.
- Refactor to pull measurement code out as separate function.
bmp280
- Fix lack of clamp on range during data capture.
* at91-sama5d2_adc
- Handle unfinished conversions correctly.
- Allow use of triggers other than it's own.
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ccs811
- Add DT binding docs and match table.
- Support external reset and wakeup pins.
* hid-sensors
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ltr501
- Constify some structs.
* vcnl4000
- Fix an endian issue by using explicit byte swapped i2c accessors.
-----BEGIN PGP SIGNATURE-----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=mYqq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, cleanups and features for IIO in the 5.8 cycle
Usual mixed back but with a few subsystem wide or device type
wide cleanups.
New device support
* adis16475
- New driver supporting adis16470, adis16475, adis16477, adis16465,
adis16467, adis16500, adis16505 and adis16507.
Includes some rework of the adis library to simplify using it
for this new driver.
* ak8974
- Add support for Alps hscdt008a. ID only. Related patches add support
for scale.
* atlas-sensor
- Add support for RTD-SM OEM temperature sensor.
* cm32181
- Add support for CM3218 including support for SMBUS alert via
ACPI resources.
* ltc2632
- Add support for ltc2634-12/10/8 DACS including handling per
device type numbers of channels.
Major Features
* cm32181
- ACPI bindings including parsing CPM0 and CPM1 custom ACPI tables.
Includes minor tidy ups and fixes.
* vcnl4000
- Add event support
- Add buffered data capture support
- Add control of sampling frequency
Cleanups and minor fixes.
* core
- Trivial rework of iio_device_alloc to use an early return and
improve readability.
- Precursors to addition of multiple buffer support. So far
minor refactoring.
* subsystem wide
- Use get_unaligned_be24 slightly improve readability over open
coding it.
* adis drivers
- Use iio_get_debugfs_dentry access function.
* bh1780, cm32181, cm3232, gp2ap02a00f, opt3001, st_uvis25, vl6180,
dmard06, kxsd9
- Drop use of of_match_ptr to allow ACPI based probing via PRP0001.
Part of clear out of this to avoid cut and paste into new drivers.
* ad5592r, ad5593r
- Fix typos
* ad5933
- Use managed interfaces to automate error handling and remove.
* ak8974
- Fix wrong number of 'real bits' for buffered data.
- Refactor to pull measurement code out as separate function.
bmp280
- Fix lack of clamp on range during data capture.
* at91-sama5d2_adc
- Handle unfinished conversions correctly.
- Allow use of triggers other than it's own.
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ccs811
- Add DT binding docs and match table.
- Support external reset and wakeup pins.
* hid-sensors
- Reorganize buffer setup and tear down as part of long running
subsystem wide rework.
* ltr501
- Constify some structs.
* vcnl4000
- Fix an endian issue by using explicit byte swapped i2c accessors.
* tag 'iio-for-5.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (74 commits)
iio: light: ltr501: Constify structs
staging: iio: ad5933: attach life-cycle of kfifo buffer to parent device and use managed calls throughout
iio: bmp280: fix compensation of humidity
iio: light: cm32181: Fix integartion time typo
iio: light: cm32181: Add support for parsing CPM0 and CPM1 ACPI tables
iio: light: cm32181: Make lux_per_bit and lux_per_bit_base_it runtime settings
iio: light: cm32181: Use units of 1/100000th for calibscale and lux_per_bit
iio: light: cm32181: Change reg_init to use a bitmap of which registers to init
iio: light: cm32181: Handle CM3218 ACPI devices with 2 I2C resources
iio: light: cm32181: Clean up the probe function a bit
iio: light: cm32181: Add support for the CM3218
iio: light: cm32181: Add some extra register defines
iio: light: cm32181: Add support for ACPI enumeration
iio: light: cm32181: Switch to new style i2c-driver probe function
iio: hid-sensors: move triggered buffer setup into hid_sensor_setup_trigger
iio: vcnl4000: Add buffer support for VCNL4010/20.
iio: vcnl4000: Add sampling frequency support for VCNL4010/20.
iio: vcnl4000: Add event support for VCNL4010/20.
iio: vcnl4000: Factorize data reading and writing.
iio: vcnl4000: Fix i2c swapped word reading.
...
When a station is removed, the driver check that all the Tx frames were
correctly sent. However, the station can be removed before all the Tx
frames were acknowledged and a false positive warning can be emitted.
The previous commit has added a trace when driver received an
acknowledge for a non-existent station. It appear that these events
are perfectly correlated and there is no leak.
Now, the subject is perfectly understood. Remove the warning. Just keep
a debug trace in case we have any doubt in the future.
In the past, the subject has already been discussed here:
https://lore.kernel.org/driverdev-devel/6287924.ghGFUMk3OD@pc-42/
Fixes: 4bbc6a3e7a ("staging: wfx: make warning about pending frame less scary")
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-20-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some resources are associated to the outgoing of the stations. To avoid
any resource leaks. It is important to understand why an acknowledge is
not associated to any station.
Add a trace for that purpose.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-19-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function wfx_tx_flush() wait for there is no more queued frames in
hardware queue. Then, for the sanity, it checks that there is no more
pending frame on any AC queue.
However, there is a race here. It may happens that hardware queues are
empty, but the counters of the AC queues are not yet updated. So, it may
produce false-positive warning.
The easiest way to solve the problem is just to remove the sanity check.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-18-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when mac80211 want to disable beacon filtering, the driver
reset the filter table and disable the beacon filtering. Only the latter
action is required.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-16-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple vif are in use (= one access point and one station), and
when the channels are different, it is necessary to enable power save on
station.
The firmware check that steps are done in the correct order:
- AP can't start if PS is not enable on the station
- PS can't set on the station before the association has finished
(= before the call set_bss_params)
Obviously, in add, when one of the interface disappears, it is necessary to
restore the power save status.
wfx_update_pm() is able to set the correct PS configuration. But it has
to be called at the right time:
1. before hif_start(), but after the channel configuration is known
2. after hif_set_bss_params()
3. after hif_reset()
Therefore, the call to wfx_update_pm() from wfx_add_interface() is too
early to address 1.
The call after hif_set_bss_params() already exists.
For the symmetry, the call from wfx_remove_interface() (that handle 3.)
is also relocated.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-15-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device disallows to start a scan request between hif_join() and
hif_set_bss_params(). The driver is not protected against that. The
worst case happens when association is aborted and hif_set_bss_params()
never happens.
mac80211 would never ask for scan during the association process. So,
this patch just aborts the association in progress when scan is
requested.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-14-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In fact, wfx_do_unjoin() resets the interface. This mechanism can be
used in more cases than just disassociating from a BSS. So, rename it to
reflect that fact.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-12-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wfx_tx_policy_put() use data from the skb. However, the call to
skb_pull() has just discarded them (even if the memory is in fact not
really discarded).
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-11-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function wfx_notify_buffered_tx() need to know if the frame was
associated to a station. This information is available in the Control
Buffer (CB) of the skb. However, when wfx_notify_buffered_tx() is
called, the CB is no more available. Thus, the caller has to take care
of this information.
wfx_notify_buffered_tx() is a specific case. All the other function are
called before the destruction of the CB. So, this patch align the API of
wfx_notify_buffered_tx() with the other functions. Call it before the CB
was destroyed and drop the extra argument 'has_sta'.
It is also the right time to rename it into wfx_tx_update_sta() (which
is closer to the behavior of the function).
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-10-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wfx_tx_confirm_cb() is a big function. A big part of its body aims to
fill the rates list. So, create a new function wfx_tx_fill_rates() and
make wfx_tx_confirm_cb() smaller.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-9-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When wfx_flush() is called, the status of pending frames are reported to
mac80211 with random status. mac80211 probably won't interpret this
status in this case, but it is cleaner to return a correctly initialized
status.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-8-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before to start the scan request, the firmware signals (with a null
frame) to the AP it won't be able to receive data. This frame can be
long to send: up to 512TU. The current calculus of the scan timeout does
not take into account this delay.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-5-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Strings are allowed to exceed 80 columns but, in this case, the format
arguments should be placed on a new line. Apply this rule to the whole
code of the driver.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-3-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device does not answer to the command hif_shutdown. Therefore,
hif_shutdown() is a bit special. It bypasses some of work normally made
by wfx_cmd_send(). In particularly, it unlock hif_cmd.lock and
hif_cmd.key_renew_lock.
However, if the driver notice that the device is frozen, wfx_cmd_send()
stops to send data and doesn't lock the mutexes. Then, it produced a
warning when hif_shutdown() tried to unlock these mutexes.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20200515083325.378539-2-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is removing definition of CFLAGS in Makefile of vt6656 and
vt6655, as those are defining macros that are not used. This will remove
undef of one macro from vt6655/device_main.c, as it is only undef and it is
not used anywhere else, so it is safe to remove it.
Macros are removed from vt665x/Makefile and vt6655/device_main.c.
Signed-off-by: Matej Dujava <mdujava@kocurkovo.cz>
Link: https://lore.kernel.org/r/1589397351-24655-2-git-send-email-mdujava@kocurkovo.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coding style issue reported by checkpatch.pl
This patch clears the checkpatch.pl "Block comments should align
the * on each line" warning.
Also cleared /****** and blank line.
Signed-off-by: John Oldman <john.oldman@polehill.co.uk>
Link: https://lore.kernel.org/r/20200513125405.28242-1-john.oldman@polehill.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the driver version of the line-coding request and use the protocol
definition directly as was originally intended instead.
This specifically avoids having the two versions of what is supposed to
be the same struct ever getting out of sync.
Note that this has in fact already happened once when the protocol
definition had its implicit padding removed while the driver struct
wasn't updated. The fact that we used the size of the then larger driver
struct when memcpying its content to the stack didn't exactly make
things better. A later addition of a flow-control field incidentally
made the structures match again.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200514070548.4423-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes use of the macro ATTRIBUTE_GROUPS to create the groups
instead of defining them manually.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1589534465-7423-7-git-send-email-christian.gromm@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the typo in the Kconfig file where it says
tranceiver instead of transceiver.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/1589534465-7423-6-git-send-email-christian.gromm@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the functions dev_notice with dev_dbg to silence
the driver during normal operation.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1589534465-7423-5-git-send-email-christian.gromm@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch checks the number of endpoints reported by the USB
interface descriptor and throws an error if the number exceeds
MAX_NUM_ENDPOINTS.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1589534465-7423-4-git-send-email-christian.gromm@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the reference to the driver API file for USB error
codes.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1589534465-7423-3-git-send-email-christian.gromm@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
