This patch implements the USB part of the Diolan USB-I2C/SPI/GPIO
Master Adapter DLN-2. Details about the device can be found here:
https://www.diolan.com/i2c/i2c_interface.html.
Information about the USB protocol can be found in the Programmer's
Reference Manual [1], see section 1.7.
Because the hardware has a single transmit endpoint and a single
receive endpoint the communication between the various DLN2 drivers
and the hardware will be muxed/demuxed by this driver.
Each DLN2 module will be identified by the handle field within the DLN2
message header. If a DLN2 module issues multiple commands in parallel
they will be identified by the echo counter field in the message header.
The DLN2 modules can use the dln2_transfer() function to issue a
command and wait for its response. They can also register a callback
that is going to be called when a specific event id is generated by
the device (e.g. GPIO interrupts). The device uses handle 0 for
sending events.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset
configuration") enabled configuring the PM features for twl4030.
This caused poweroff command to fail on devices that have the
BCI charger on twl4030 wired, or have power wired for VBUS.
Instead of powering off, the device reboots. This is because
voltage is detected on charger or VBUS with the default bits
enabled for the power transition registers.
To fix the issue, let's just clear VBUS and CHG bits as we want
poweroff command to keep the system powered off.
Fixes: e7cd1d1eb1 ("mfd: twl4030-power: Add generic reset configuration")
Cc: stable@vger.kernel.org # v3.16+
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All interrupts coming from MUIC were ignored because interrupt source
register was masked.
The Maxim 77693 has a "interrupt source" - a separate register and interrupts
which give information about PMIC block triggering the individual
interrupt (charger, topsys, MUIC, flash LED).
By default bootloader could initialize this register to "mask all"
value. In such case (observed on Trats2 board) MUIC interrupts won't be
generated regardless of their mask status. Regmap irq chip was unmasking
individual MUIC interrupts but the source was masked
Before introducing regmap irq chip this interrupt source was unmasked,
read and acked. Reading and acking is not necessary but unmasking is.
Fixes: 342d669c1e ("mfd: max77693: Handle IRQs using regmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Interrupts coming from Maxim77693 MUIC block (MicroUSB Interface
Controller) were not handled at all because wrong regmap was used for
MUIC's regmap_irq_chip.
The MUIC component of Maxim 77693 uses different I2C address thus second
regmap is created and used by max77693 extcon driver. The registers for
MUIC interrupts are also in that block and should be handled by that
second regmap.
However the regmap irq chip for MUIC was configured with default regmap
which could not read MUIC registers.
Fixes: 342d669c1e ("mfd: max77693: Handle IRQs using regmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow more than one viperboard to be connected by registering with
PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE.
The subdevices are currently registered with PLATFORM_DEVID_NONE, which
will cause a name collision on the platform bus when a second viperboard
is plugged in:
viperboard 1-2.4:1.0: version 0.00 found at bus 001 address 004
------------[ cut here ]------------
WARNING: CPU: 0 PID: 181 at /home/johan/work/omicron/src/linux/fs/sysfs/dir.c:31 sysfs_warn_dup+0x74/0x84()
sysfs: cannot create duplicate filename '/bus/platform/devices/viperboard-gpio'
Modules linked in: i2c_viperboard viperboard netconsole [last unloaded: viperboard]
CPU: 0 PID: 181 Comm: bash Tainted: G W 3.17.0-rc6 #1
[<c0016bf4>] (unwind_backtrace) from [<c0013860>] (show_stack+0x20/0x24)
[<c0013860>] (show_stack) from [<c04305f8>] (dump_stack+0x24/0x28)
[<c04305f8>] (dump_stack) from [<c0040fb4>] (warn_slowpath_common+0x80/0x98)
[<c0040fb4>] (warn_slowpath_common) from [<c004100c>] (warn_slowpath_fmt+0x40/0x48)
[<c004100c>] (warn_slowpath_fmt) from [<c016f1bc>] (sysfs_warn_dup+0x74/0x84)
[<c016f1bc>] (sysfs_warn_dup) from [<c016f548>] (sysfs_do_create_link_sd.isra.2+0xcc/0xd0)
[<c016f548>] (sysfs_do_create_link_sd.isra.2) from [<c016f588>] (sysfs_create_link+0x3c/0x48)
[<c016f588>] (sysfs_create_link) from [<c02867ec>] (bus_add_device+0x12c/0x1e0)
[<c02867ec>] (bus_add_device) from [<c0284820>] (device_add+0x410/0x584)
[<c0284820>] (device_add) from [<c0289440>] (platform_device_add+0xd8/0x26c)
[<c0289440>] (platform_device_add) from [<c02a5ae4>] (mfd_add_device+0x240/0x344)
[<c02a5ae4>] (mfd_add_device) from [<c02a5ce0>] (mfd_add_devices+0xb8/0x110)
[<c02a5ce0>] (mfd_add_devices) from [<bf00d1c8>] (vprbrd_probe+0x160/0x1b0 [viperboard])
[<bf00d1c8>] (vprbrd_probe [viperboard]) from [<c030c000>] (usb_probe_interface+0x1bc/0x2a8)
[<c030c000>] (usb_probe_interface) from [<c028768c>] (driver_probe_device+0x14c/0x3ac)
[<c028768c>] (driver_probe_device) from [<c02879e4>] (__driver_attach+0xa4/0xa8)
[<c02879e4>] (__driver_attach) from [<c0285698>] (bus_for_each_dev+0x70/0xa4)
[<c0285698>] (bus_for_each_dev) from [<c0287030>] (driver_attach+0x2c/0x30)
[<c0287030>] (driver_attach) from [<c030a288>] (usb_store_new_id+0x170/0x1ac)
[<c030a288>] (usb_store_new_id) from [<c030a2f8>] (new_id_store+0x34/0x3c)
[<c030a2f8>] (new_id_store) from [<c02853ec>] (drv_attr_store+0x30/0x3c)
[<c02853ec>] (drv_attr_store) from [<c016eaa8>] (sysfs_kf_write+0x5c/0x60)
[<c016eaa8>] (sysfs_kf_write) from [<c016dc68>] (kernfs_fop_write+0xd4/0x194)
[<c016dc68>] (kernfs_fop_write) from [<c010fe40>] (vfs_write+0xb4/0x1c0)
[<c010fe40>] (vfs_write) from [<c01104a8>] (SyS_write+0x4c/0xa0)
[<c01104a8>] (SyS_write) from [<c000f900>] (ret_fast_syscall+0x0/0x48)
---[ end trace 98e8603c22d65817 ]---
viperboard 1-2.4:1.0: Failed to add mfd devices to core.
viperboard: probe of 1-2.4:1.0 failed with error -17
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rtsx_pci_power_off() is called only from rtsx_pci_suspend(), which isn't
built when PM is disabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The least significat byte of the GPIO value read register
on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct
against datasheet and tested on the STMPE2401 hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The device tree structure is composed of two lists; the 'allnodes' list
which is a singly linked list containing every node in the tree, and the
child->parent structure where each parent node has a singly linked list
of children. All of the data in the allnodes list can be easily
reproduced with the parent-child lists, so of_allnodes is actually
unnecessary. Remove it entirely which saves a bit of memory and
simplifies the data structure quite a lot.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: Pantelis Antoniou <pantelis@pantelis.antoniou@konsulko.com>
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xxsZ
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch"
[ Delayed to after the poweer/reset pull due to Kconfig problems with
recursive Kconfig select/depends-on chains. - Linus ]
* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
i2c: i2c-cros-ec-tunnel: Set retries to 3
mfd: cros_ec: move locking into cros_ec_cmd_xfer
mfd: cros_ec: stop calling ->cmd_xfer() directly
mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
mfd: arizona: Correct mask to allow setting micbias external cap
mfd: Add ACPI support
Revert "mfd: wm5102: Manually apply register patch"
mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
mfd: Inherit coherent_dma_mask from parent device
mfd: Document DT bindings for Qualcomm SPMI PMICs
mfd: Add support for Qualcomm SPMI PMICs
mfd: dt-bindings: pm8xxx: Add new compatible string
mfd: axp209x: Drop the parent supplies field
mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
mfd: syscon: Add Atmel GPBR DT bindings documention
...
Convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
Register ntc_thermistor driver with thermal subsystem.
Add support for F15h M60h to k10temp driver.
Add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vI5p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for menf21bmc.
- convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
- register ntc_thermistor driver with thermal subsystem.
- add support for F15h M60h to k10temp driver.
- add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18
* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
MAINTAINERS: add entry for the PWM fan driver
hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (k10temp) Add support for F15h M60h
hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
hwmon: (ads1015) Use of_property_read_u32 at appropriate places
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
X-Powers AXP288 is a customized PMIC for Intel Baytrail-CR platforms. Similar
to AXP202/209, AXP288 comes with USB charger, more LDO and BUCK channels, and
AD converters. It also provides extended status and interrupt reporting
capabilities than the devices currently supported in axp20x.c.
In addition to feature extension, this patch also adds ACPI binding for
enumeration.
This consolidated driver should support more X-Powers' PMICs in both device
tree and ACPI enumerated platforms.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When an EC command returns EC_RES_IN_PROGRESS, we need to query
the state of the EC until it indicates that it is no longer busy.
Do this in cros_ec_cmd_xfer() under the EC's mutex so that other
commands (e.g. keyboard, I2C passtru) aren't issued to the EC while
it is working on the in-progress command.
The 10 milliseconds delay and the number of retries are the values
that were used by the flashrom tool when retrying commands.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that there's a central cros_ec_cmd_xfer(), move the locking
out of the SPI driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of having users of the ChromeOS EC call the interface-specific
cmd_xfer() callback directly, introduce a central cros_ec_cmd_xfer()
to use instead. This will allow us to put all the locking and retry
logic in one place instead of duplicating it across the different
drivers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If someone sends a EC_CMD_REBOOT_EC to the EC, the EC will likely be
unresponsive for quite a while. Add a delay to the end of the command
to prevent random failures of future commands.
NOTES:
* This could be optimized a bit by simply delaying the next command
sent, but EC_CMD_REBOOT_EC is such a rare command that the extra
complexity doesn't seem worth it.
* This is a bit of an "ugly hack" since the SPI driver is effectively
snooping on the communication and making a lot of assumptions. It
would be nice to architect in some better solution long term.
* This same logic probably needs to be applied to the i2c driver.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the mask for the external capacitor bit is missing when
writing the MICBIAS config meaning it will never be set this patch fixes
this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If an MFD device is backed by ACPI namespace, we should allow subdevice
drivers to access their corresponding ACPI companion devices through normal
means (e.g using ACPI_COMPANION()).
This patch adds such support to the MFD core. If the MFD parent device
does not specify any ACPI _HID/_CID for the child device, the child
device will share the parent ACPI companion device. Otherwise the child
device will be assigned with the corresponding ACPI companion, if found
in the namespace below the parent.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit d9d03496f6.
It seems this commit was applied twice, once through ASoC and once
through MFD:
commit 4c9bb8bc35
mfd: wm5102: Manually apply register patch
commit d9d03496f6
mfd: wm5102: Manually apply register patch
This has lead to a small piece of duplicate code. It is harmless hence
how it has gone unoticed for so long. This patch reverts one of the two
commits removing the unneeded code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The logic in AFE_Pen_Ctrl bitmask in the CTRL register is different for five
wire versus four or eight wire touschscreens. This patch should fix this for
five-wire touch screens. There should be no change needed here for four and
eight wire tousch screens.
Signed-off-by: Jeff Lance <j-lance1@ti.com>
[bigeasy: keep the change mfd only]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
dma_mask and dma_parms are already inherited from the parent device but
dma_coherent_mask was left uninitialized (set to zero thanks to kzalloc).
Set sub-device coherent_dma_mask to its parent value to simplify
sub-drivers making use of dma coherent helper functions (those drivers
currently have to explicitly set the dma coherent mask using
dma_set_coherent_mask function).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Qualcomm SPMI PMIC chips are components used with the
Snapdragon 800 series SoC family. This driver exists
largely as a glue mfd component, it exists to be an owner
of an SPMI regmap for children devices described in
device tree.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that the regulator code get its parent supplies purely from the DT, we can
drop the parent supplies resources in the MFD driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ti,system-power-controller is more or less the standard way of
indicating that the PMIC is the system wide power controller and hence
may be used to switch off the system. Almost ALL TI PMIC drivers and
many Maxim PMIC drivers follow the same style.
So support 'ti,system-power-controller' in addition to the usual
'ti,use_poweroff' to indicate that the PMIC instance has control for
switching off the system.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Let's define the voltatile registers (those that can't be cached) and
enable caching. The rk808 is accessed almost constantly with cpufreq
so this is really nice.
As measured by ftrace:
before this change: cpu0_set_target() => ~2200us
after this change: cpu0_set_target() => ~500us
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We use a dummy IRQ chip to dispatch interrupts to the two seperate IRQ
domains on the Arizona devices. This is just a simple software IRQ chip
and thus the current handle_edge_irq is unnecessary for its needs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The max14577 MFD cells do not have any resources so the IRQ domain
passed to mfd_add_devices is not used.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The stmpe_platform_data has a irq_over_gpio field, which allows the
system to read STMPE events whenever an IRQ occurs on a GPIO pin.
This patch adds the ability to configure this field and to use a GPIO
as an IRQ source for boards configuring the STMPE in device tree.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch fix warning message with CONFIG_PM_SLEEP disabled
If CONFIG_PM_SLEEP is not enabled we receive the following warning message:
drivers/mfd/intel_soc_pmic_core.c:118:12:
warning: 'intel_soc_pmic_suspend' defined but not used
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
pci_enable_msi() can return failure with both positive and negative
integers -- it returns 0 for success -- but is only tested here for
"if (ret < 0)". This causes us to try to use MSI on the RTS5249 SD
reader in the Dell XPS 11 when enabling MSI failed, causing:
[ 1.737110] rtsx_pci: probe of 0000:05:00.0 failed with error -110
Cc: stable <stable@vger.kernel.org>
Reported-by: D. Jared Dominguez <Jared_Dominguez@Dell.com>
Tested-by: D. Jared Dominguez <Jared_Dominguez@Dell.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the resume path, the ADC invokes am335x_tsc_se_set_cache() with 0 as
the steps argument if continous mode is not in use. This in turn disables
all steps and so the TSC is not working until one ADC sampling is
performed.
This patch fixes it by writing the current cached mask instead of the
passed steps.
Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADCA
synchronization")
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow regmap to provide debugfs access to the register map by telling it
what registers are valid.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Setup the PMIC to make a restart when a watchdog interrupt occures.
If this is not configured, the PMIC will shut down the power supply
without a restart.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When dump a content of the registers let's use snprintf() directly with %*ph
specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds driver to support HiSilicon Hi6421 PMIC. Hi6421 includes multi-
functions, such as regulators, codec, ADCs, Coulomb counter, etc.
This driver includes core APIs _only_.
Drivers for individul components, like voltage regulators, are
implemented in corresponding driver directories and files.
Registers in Hi6421 are memory mapped, so using regmap-mmio API.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch removes FSF address because it can be changed. While here, update
the copyright lines by adding Intel Corp. to them.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Quark X1000 SoC supports IRQ based GPIO. This patch will
enable MFD support for Quark X1000 and provide IRQ resources
to Quark X1000 GPIO device driver.
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Tested-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch refactors the driver to use helper functions instead of
copy'n'pasted pieces of code.
It also introduces an additional struct to hold a chipset info. The chipset
info will be used to store features that are supported by specific processor or
chipset. LPC_SCH supports SMBUS, GPIO and WDT features. As this code base might
expand further to support more processors, this implementation will help to
keep code base clean and manageable.
The patch is partially based on the work done by Chang Rebecca Swee Fun.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK808 chip is a power management IC for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clkout
The RK808 core driver is registered as a platform driver and provides
communication through I2C with the host device for the different
components.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Zhang Qing <zhangqing@rock-chips.com>
Tested-by: Heiko <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Current code init regmap with &da9052_regmap_config for both da9052-spi and
da9052-i2c drivers. da9052-spi sets the read_flag_mask.
The same setting may be applied for da9052-i2c if da9052-spi driver is loaded
first because they actually use the same regmap_config setting.
Fix this issue by using a local variable for regmap_config in da9052-spi driver,
so the settings in spi driver won't impact the settings in i2c driver.
Also makes da9052_regmap_config const to avoid similar issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If one of the internal Arizona IRQs is set as a wake source this needs
to be propogated back to the actual IRQ line that the Arizona device is
attached to.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some boards need to set the INn_MODE[1:0] register to change
the input signal patch. This wlf,inmode property is optional.
If present, values must be specified less than or equal to
the number of input singals. If values less than the number
of input signals, elements that has not been specifed are set
to 0 by default.
Example:
- wlf,inmode = <2 0 2>; /* IN1, IN3 use DMIC */
Signed-off-by: Inha Song <ideal.song@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some arizona devices have a second asynchronous sample rate, add the
registers necessary to support this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Ricoh RN5T618 is a power management IC which integrates 3 step-down
DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
fuel gauge, ADC, GPIOs and a watchdog timer.
This commit adds a MFD core driver to support the I2C communication
with the device.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
After enabling and disabling ADC continuous mode via sysfs, ts_print_raw
fails to return any data. This is because when ADC is configured for
continuous mode, it disables touch screen steps.These steps are not
re-enabled when ADC continuous mode is disabled. Therefore existing values
of REG_SE needs to be cached before enabling continuous mode and
disabling touch screen steps and enabling ADC steps. The cached value
are to be restored to REG_SE once ADC is disabled.
Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization")
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
http://www.ti.com/lit/pdf/SWCZ010:
Glitch on SDA-SCL not managed correctly by the I2C IP
Impact:
The standard specifies that the I2C transfer should restart on a start
event in all cases. The current design does not support two consecutive
Start conditions. This can cause the first real access after such a
glitch to be corrupted.
Description:
An unexpected glitch on SDA and SCL can generate a wrong start event.
In the current design, the SCL line must toggle two times to detect a
new start event and completely restart the I2C access; hence the real
start event is not detected in the case of a single SCL toggle.
Workaround:
Repeat I2C access.
A simpler workaround is to make a dummy transfer just before the first
access to the tps65910 chip. This can be done unconditionally.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Numbers are generated by taking the largest currently used values.
drivers/mfd/stmpe.c:252:17:
warning: Variable length array is used.
drivers/mfd/stmpe.c:857:16:
warning: Variable length array is used.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The largest byte size in use currently is 8. Fix array size to 9.
drivers/mfd/max8925-i2c.c:40:33:
warning: Variable length array is used
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The following functions appear to be unused since v2.6.39:
pm860x_page_reg_read()
pm860x_page_bulk_write()
pm860x_page_set_bits()
Let's remove them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the LPC Device IDs for the Intel 9 Series PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch improves support for the flash cell of
max77693 mfd by adding relevant of_compatible field
and a structure for caching related platform data.
Added are also FLASH registers related macro definitions.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is the same as used in Baytrail so add the new PCI ID to the driver's
list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit b42261078a ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.
So remove the I2C_FUNC_SMBUS_BYTE_DATA functionality check in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert a zero return value on error to a negative one, as returned
elsewhere in the function.
Additionally, converted 1 << 7 to BIT(7) at the suggestion of Lee Jones.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
regmap_add_irq_chip is called from arizona_irq_init with the irq_base
specified as -1 and regmap_add_irq_chip uses if (irq_base) to check if
it should use legacy IRQ mapping. As such the irq mappings are currently
added with irq_domain_add_legacy, rather than irq_domain_add_linear.
This is clearly a typo as there is no reason why this driver can't use
irq_domain_add_linear.
This patch corrects this by passing the irq_base as zero to
regmap_add_irq_chip.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Mark some additional registers as volatile. The write sequencer control
registers should not be cached, as we don't ever want their value
synchronised as this might cause a write sequence to be accidentally
initiated.
Additionally, the DAC_COMP registers require special preconditions to
write so there values wouldn't be updated accurately during a register
sync.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
During init the core checks if the wm5102 has finished starting by reading
register 0x19 and looking at the value. This read always fails since this
is not a readable register, mark it as being one. While we're at it provide
a constant for the register name (as supplied by Charles Keepax).
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert a zero return value on error to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The interfaces that used to be built in only (interrupts IIRC) no longer
are so allow the driver to be built as a module fixing arm64 allmodconfig
builds.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If vtg is NULL, it is not possible to access its mode_reg field. At all
sites where the static function menelaus_set_voltage is called, the first
argument is the address of a structure defined in the file. So, the null
test is unnecessary and is removed. Also, a label is done away with.
This problem was found using the following Coccinelle semantic match:
// <smpl>
@@
expression E, E1;
identifier f;
statement S1,S2,S3;
@@
* if (E == NULL)
{
... when != if (E == NULL) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We'd like to be able to build the WM8994 family as modules, but the
build will fail if the external symbols aren't exported first.
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Suspicious implicit sign extension where 'reg' (unsigned char) is
promoted in reg << clksrc to int, then sign-extended to unsigned
long. If reg << clksrc is greater than 0x7FFFFFFF, the upper bits
of the result will all be 1.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the original code a return value variable was provided, but it
was never checked and the user was never informed of failure. Now
it is and they are.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The return value of platform_device_add() is checked after every
other use throughout the kernel.
We're also sliding in another cheeky dev_err() => dev_warn() change
as we're not actually erroring out here, rather reporting the fact
that something's gone wrong, but carrying on regardless.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As 'reg' is unsigned, it can't be less than 0, so checking if it is
greater than or equal to 0 will always result in a true condition.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Chip identifier wm5102_reva_patch is always overwritten with
wm5102_revb_patch, even when the code is run on a Rev-A chip. Place
in the missing break to force the code into doing something sensible
instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Checking the result of container_of() against NULL will always result to
false. Using the offset of member 'chip_out' to find the start of 'struct
htcpld_chip' will result in an offset error when .get_chip() is attempting
to obtain 'htcpld-in'. Instead, we'll use the correct member based on a
previously the set chip label.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Logically dead code (DEADCODE)
dead_error_line: Execution cannot reach this statement: return;
Remove the check for NULL.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch prepares for changing the max14577 charger driver to allow
configuring battery-dependent settings from DTS.
The patch moves from regulator driver to MFD core driver and exports:
- function for calculating register value for charger's current;
- table of limits for chargers (MAX14577, MAX77836).
Previously they were used only by the max14577 regulator driver. In next
patch the charger driver will use them as well. Exporting them will
reduce unnecessary code duplication.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a "maxim,max14577-charger" of_compatible to the mfd_cell so the
MFD child device (the charger) will have its own of_node set. This will
be used by the max14577 charger driver in next patches to obtain battery
configuration from DTS.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MEN 14F021P00 Board Management Controller provides an
I2C interface to the host to access the feature implemented in the BMC.
The BMC is a PIC Microntroller assembled on CPCI Card from MEN Mikroelektronik
and on a few Box/Display Computer.
Added MFD Core driver, supporting the I2C communication to the device.
The MFD driver currently supports the following features:
- Watchdog
- LEDs
- Hwmon (voltage monitoring)
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch series updates the device tree vendor prefix for
Dialog Semiconductor.
Various methods are currently used throughout the kernel: 'diasemi',
'dialog' and 'dlg'. Others have also been suggested.
This patch set aims to consolidate the usage of the vendor prefix to
use a common standard. The prefix 'dlg' is used.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 43fef47f94 (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.
This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678ab6 (ARM: dts:
Revert enabling of twl configuration for n900).
Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.
This allows us to enable the PMIC configuration for n900.
Fixes: 43fef47f94 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The config symbol 'CONFIG_DEBUG_FS' should be protected by a 'ifdef' instead
of a plain 'if'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The rtsx_usb driver contains the table for the devices it supports but
doesn't export it. As a result, no alias is generated and it doesn't
get loaded automatically.
Via https://bugzilla.novell.com/show_bug.cgi?id=890096
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: Marcel Witte <wittemar@googlemail.com>
Cc: Roger Tseng <rogerable@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
single-ulpi-bypass is a flag used for older OMAP3 silicon.
The flag when set, can excite code that improperly uses the
OMAP_UHH_HOSTCONFIG_UPLI_BYPASS define to clear the corresponding bit.
Instead it clears all of the other bits disabling all of the ports in
the process.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Welling <mwelling@emacinc.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We only request the control interface error IRQ if we set ctrlif_error,
as such we should only free it in that situation. Otherwise we will
attempt to free an IRQ we never requested and get a warning from the IRQ
core.
This patch moves the ctrlif_error variable into the arizona structure
and checks it in all cases we free the control interface error IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some parts have a third ISRC, this patch adds handling for the under and
overclocked interrupts from this ISRC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer versions of the IP have a lot of new interrupts and move several
existing interrupts. This patch adds the register definitions and regmap
hookup for these interrupts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer versions of the IP introduce short circuit protection which will
also shutdown the speaker. Rename the interrupt and associated register
bits associated with thermal events to better fit the function and avoid
conflict with future interrupt additions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
wm5110 has interrupts to signal that an output has fully enabled. This
patch adds in these interrupts although use is not made of them yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DCS_DAC_DONE and DCS_HP_DONE interrupts do not exist on the wm5110
version of the IP. This patch removes them from the regmap IRQ
structure.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>