So far we've been running all code without locking of any sort. This wasn't
really an issue because I didn't see any parallel access to the shadow MMU
code coming.
But then I started to implement dirty bitmapping to MOL which has the video
code in its own thread, so suddenly we had the dirty bitmap code run in
parallel to the shadow mmu code. And with that came trouble.
So I went ahead and made the MMU modifying functions as parallelizable as
I could think of. I hope I didn't screw up too much RCU logic :-). If you
know your way around RCU and locking and what needs to be done when, please
take a look at this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Due to previous changes, the Book3S_32 guest MMU code didn't compile properly
when enabling debugging.
This patch repairs the broken code paths, making it possible to define DEBUG_MMU
and friends again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We need to tell the guest the opcodes that make up a hypercall through
interfaces that are controlled by userspace. So we need to add a call
for userspace to allow it to query those opcodes so it can pass them
on.
This is required because the hypercall opcodes can change based on
the hypervisor conditions. If we're running in hardware accelerated
hypervisor mode, a hypercall looks different from when we're running
without hardware acceleration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
On BookE the preferred way to write the EE bit is the wrteei instruction. It
already encodes the EE bit in the instruction.
So in order to get BookE some speedups as well, let's also PV'nize thati
instruction.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is also a form of mtmsr where all bits need to be addressed. While the
PPC64 Linux kernel behaves resonably well here, on PPC32 we do not have an
L=1 form. It does mtmsr even for simple things like only changing EE.
So we need to hook into that one as well and check for a mask of bits that we
deem safe to change from within guest context.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The PowerPC ISA has a special instruction for mtmsr that only changes the EE
and RI bits, namely the L=1 form.
Since that one is reasonably often occuring and simple to implement, let's
go with this first. Writing EE=0 is always just a store. Doing EE=1 also
requires us to check for pending interrupts and if necessary exit back to the
hypervisor.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When we hook an instruction we need to make sure we don't clobber any of
the registers at that point. So we write them out to scratch space in the
magic page. To make sure we don't fall into a race with another piece of
hooked code, we need to disable interrupts.
To make the later patches and code in general easier readable, let's introduce
a set of defines that save and restore r30, r31 and cr. Let's also define some
helpers to read the lower 32 bits of a 64 bit field on 32 bit systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We will need to patch several instruction streams over to a different
code path, so we need a way to patch a single instruction with a branch
somewhere else.
This patch adds a helper to facilitate this patching.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We will soon require more sophisticated methods to replace single instructions
with multiple instructions. We do that by branching to a memory region where we
write replacement code for the instruction to.
This region needs to be within 32 MB of the patched instruction though, because
that's the furthest we can jump with immediate branches.
So we keep 1MB of free space around in bss. After we're done initing we can just
tell the mm system that the unused pages are free, but until then we have enough
space to fit all our code in.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
With our current MMU scheme we don't need to know about the tlbsync instruction.
So we can just nop it out.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some instructions can simply be replaced by load and store instructions to
or from the magic page.
This patch replaces often called instructions that fall into the above category.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We will soon start and replace instructions from the text section with
other, paravirtualized versions. To ease the readability of those patches
I split out the generic looping and magic page mapping code out.
This patch still only contains stubs. But at least it loops through the
text section :).
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We have all the hypervisor pieces in place now, but the guest parts are still
missing.
This patch implements basic awareness of KVM when running Linux as guest. It
doesn't do anything with it yet though.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Now that we have the shared page in place and the MMU code knows about
the magic page, we can expose that capability to the guest!
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We need to override EA as well as PA lookups for the magic page. When the guest
tells us to project it, the magic page overrides any guest mappings.
In order to reflect that, we need to hook into all the MMU layers of KVM to
force map the magic page if necessary.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We will be introducing a method to project the shared page in guest context.
As soon as we're talking about this coupling, the shared page is colled magic
page.
This patch introduces simple defines, so the follow-up patches are easier to
read.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
On PowerPC it's very normal to not support all of the physical RAM in real mode.
To check if we're matching on the shared page or not, we need to know the limits
so we can restrain ourselves to that range.
So let's make it a define instead of open-coding it. And while at it, let's also
increase it.
Signed-off-by: Alexander Graf <agraf@suse.de>
v2 -> v3:
- RMO -> PAM (non-magic page)
Signed-off-by: Avi Kivity <avi@redhat.com>
When the guest turns on interrupts again, it needs to know if we have an
interrupt pending for it. Because if so, it should rather get out of guest
context and get the interrupt.
So we introduce a new field in the shared page that we use to tell the guest
that there's a pending interrupt lying around.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
While running in hooked code we need to store register contents out because
we must not clobber any registers.
So let's add some fields to the shared page we can just happily write to.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When running in hooked code we need a way to disable interrupts without
clobbering any interrupts or exiting out to the hypervisor.
To achieve this, we have an additional critical field in the shared page. If
that field is equal to the r1 register of the guest, it tells the hypervisor
that we're in such a critical section and thus may not receive any interrupts.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
To communicate with KVM directly we need to plumb some sort of interface
between the guest and KVM. Usually those interfaces use hypercalls.
This hypercall implementation is described in the last patch of the series
in a special documentation file. Please read that for further information.
This patch implements stubs to handle KVM PPC hypercalls on the host and
guest side alike.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When in kernel mode there are 4 additional registers available that are
simple data storage. Instead of exiting to the hypervisor to read and
write those, we can just share them with the guest using the page.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The SRR0 and SRR1 registers contain cached values of the PC and MSR
respectively. They get written to by the hypervisor when an interrupt
occurs or directly by the kernel. They are also used to tell the rfi(d)
instruction where to jump to.
Because it only gets touched on defined events that, it's very simple to
share with the guest. Hypervisor and guest both have full r/w access.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The DAR register contains the address a data page fault occured at. This
register behaves pretty much like a simple data storage register that gets
written to on data faults. There is no hypervisor interaction required on
read or write.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The DSISR register contains information about a data page fault. It is fully
read/write from inside the guest context and we don't need to worry about
interacting based on writes of this register.
This patch converts all users of the current field to the shared page.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
One of the most obvious registers to share with the guest directly is the
MSR. The MSR contains the "interrupts enabled" flag which the guest has to
toggle in critical sections.
So in order to bring the overhead of interrupt en- and disabling down, let's
put msr into the shared page. Keep in mind that even though you can fully read
its contents, writing to it doesn't always update all state. There are a few
safe fields that don't require hypervisor interaction. See the documentation
for a list of MSR bits that are safe to be set from inside the guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
For transparent variable sharing between the hypervisor and guest, I introduce
a shared page. This shared page will contain all the registers the guest can
read and write safely without exiting guest context.
This patch only implements the stubs required for the basic structure of the
shared page. The actual register moving follows.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.
The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits)
powerpc/44x: Update ppc44x_defconfig
powerpc/watchdog: Make default timeout for Book-E watchdog a Kconfig option
fsl_rio: Add comments for sRIO registers.
powerpc/fsl-booke: Add e55xx (64-bit) smp defconfig
powerpc/fsl-booke: Add p5020 DS board support
powerpc/fsl-booke64: Use TLB CAMs to cover linear mapping on FSL 64-bit chips
powerpc/fsl-booke: Add support for FSL Arch v1.0 MMU in setup_page_sizes
powerpc/fsl-booke: Add support for FSL 64-bit e5500 core
powerpc/85xx: add cache-sram support
powerpc/85xx: add ngPIXIS FPGA device tree node to the P1022DS board
powerpc: Fix compile error with paca code on ppc64e
powerpc/fsl-booke: Add p3041 DS board support
oprofile/fsl emb: Don't set MSR[PMM] until after clearing the interrupt.
powerpc/fsl-booke: Add PCI device ids for P2040/P3041/P5010/P5020 QoirQ chips
powerpc/mpc8xxx_gpio: Add support for 'qoriq-gpio' controllers
powerpc/fsl_booke: Add support to boot from core other than 0
powerpc/p1022: Add probing for individual DMA channels
powerpc/fsl_soc: Search all global-utilities nodes for rstccr
powerpc: Fix invalid page flags in create TLB CAM path for PTE_64BIT
powerpc/mpc83xx: Support for MPC8308 P1M board
...
Fix up conflict with the generic irq_work changes in arch/powerpc/kernel/time.c
* 'core-memblock-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (74 commits)
x86-64: Only set max_pfn_mapped to 512 MiB if we enter via head_64.S
xen: Cope with unmapped pages when initializing kernel pagetable
memblock, bootmem: Round pfn properly for memory and reserved regions
memblock: Annotate memblock functions with __init_memblock
memblock: Allow memblock_init to be called early
memblock/arm: Fix memblock_region_is_memory() typo
x86, memblock: Remove __memblock_x86_find_in_range_size()
memblock: Fix wraparound in find_region()
x86-32, memblock: Make add_highpages honor early reserved ranges
x86, memblock: Fix crashkernel allocation
arm, memblock: Fix the sparsemem build
memblock: Fix section mismatch warnings
powerpc, memblock: Fix memblock API change fallout
memblock, microblaze: Fix memblock API change fallout
x86: Remove old bootmem code
x86, memblock: Use memblock_memory_size()/memblock_free_memory_size() to get correct dma_reserve
x86: Remove not used early_res code
x86, memblock: Replace e820_/_early string with memblock_
x86: Use memblock to replace early_res
x86, memblock: Use memblock_debug to control debug message print out
...
Fix up trivial conflicts in arch/x86/kernel/setup.c and kernel/Makefile
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (53 commits)
spi/omap2_mcspi: Verify TX reg is empty after TX only xfer with DMA
spi/omap2_mcspi: disable channel after TX_ONLY transfer in PIO mode
spi/bfin_spi: namespace local structs
spi/bfin_spi: init early
spi/bfin_spi: check per-transfer bits_per_word
spi/bfin_spi: warn when CS is driven by hardware (CPHA=0)
spi/bfin_spi: cs should be always low when a new transfer begins
spi/bfin_spi: fix typo in comment
spi/bfin_spi: reject unsupported SPI modes
spi/bfin_spi: use dma_disable_irq_nosync() in irq handler
spi/bfin_spi: combine duplicate SPI_CTL read/write logic
spi/bfin_spi: reset ctl_reg bits when setup is run again on a device
spi/bfin_spi: push all size checks into the transfer function
spi/bfin_spi: use nosync when disabling the IRQ from the IRQ handler
spi/bfin_spi: sync hardware state before reprogramming everything
spi/bfin_spi: save/restore state when suspending/resuming
spi/bfin_spi: redo GPIO CS handling
Blackfin: SPI: expand SPI bitmasks
spi/bfin_spi: use the SPI namespaced bit names
spi/bfin_spi: drop extra memory we don't need
...
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (96 commits)
apic, x86: Use BIOS settings for IBS and MCE threshold interrupt LVT offsets
apic, x86: Check if EILVT APIC registers are available (AMD only)
x86: ioapic: Call free_irte only if interrupt remapping enabled
arm: Use ARCH_IRQ_INIT_FLAGS
genirq, ARM: Fix boot on ARM platforms
genirq: Fix CONFIG_GENIRQ_NO_DEPRECATED=y build
x86: Switch sparse_irq allocations to GFP_KERNEL
genirq: Switch sparse_irq allocator to GFP_KERNEL
genirq: Make sparse_lock a mutex
x86: lguest: Use new irq allocator
genirq: Remove the now unused sparse irq leftovers
genirq: Sanitize dynamic irq handling
genirq: Remove arch_init_chip_data()
x86: xen: Sanitise sparse_irq handling
x86: Use sane enumeration
x86: uv: Clean up the direct access to irq_desc
x86: Make io_apic.c local functions static
genirq: Remove irq_2_iommu
x86: Speed up the irq_remapped check in hot pathes
intr_remap: Simplify the code further
...
Fix up trivial conflicts in arch/x86/Kconfig
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (29 commits)
sched: Export account_system_vtime()
sched: Call tick_check_idle before __irq_enter
sched: Remove irq time from available CPU power
sched: Do not account irq time to current task
x86: Add IRQ_TIME_ACCOUNTING
sched: Add IRQ_TIME_ACCOUNTING, finer accounting of irq time
sched: Add a PF flag for ksoftirqd identification
sched: Consolidate account_system_vtime extern declaration
sched: Fix softirq time accounting
sched: Drop group_capacity to 1 only if local group has extra capacity
sched: Force balancing on newidle balance if local group has capacity
sched: Set group_imb only a task can be pulled from the busiest cpu
sched: Do not consider SCHED_IDLE tasks to be cache hot
sched: Drop all load weight manipulation for RT tasks
sched: Create special class for stop/migrate work
sched: Unindent labels
sched: Comment updates: fix default latency and granularity numbers
tracing/sched: Add sched_pi_setprio tracepoint
sched: Give CPU bound RT tasks preference
sched: Try not to migrate higher priority RT tasks
...
This patch refactors the early init parsing of the chosen node so that
architectures aren't forced to provide an empty implementation of
early_init_dt_scan_chosen_arch. Instead, if an architecture wants to
do something different, it can either use a wrapper function around
early_init_dt_scan_chosen(), or it can replace it altogether.
This patch was written in preparation to adding device tree support to
both x86 ad MIPS.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: David Daney <ddaney@caviumnetworks.com>
The current code allocates and manages platform_devices created from
the device tree manually. It also uses an unsafe shortcut for
allocating the platform_device and the resource table at the same
time. (which I added in the last rework; sorry).
This patch refactors the code to use platform_device_alloc() for
allocating new devices. This reduces the amount of custom code
implemented by of_platform, eliminates the unsafe alloc trick, and has
the side benefit of letting the platform_bus code manage freeing the
device data and resources when the device is freed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Commit c3f00c70 ("perf: Separate find_get_context() from event
initialization") changed the generic perf_event code to call
perf_event_alloc, which calls the arch-specific event_init code,
before looking up the context for the new event. Unfortunately,
power_pmu_event_init uses event->ctx->task to see whether the
new event is a per-task event or a system-wide event, and thus
crashes since event->ctx is NULL at the point where
power_pmu_event_init gets called.
(The reason it needs to know whether it is a per-task event is
because there are some hardware events on Power systems which
only count when the processor is not idle, and there are some
fixed-function counters which count such events. For example,
the "run cycles" event counts cycles when the processor is not
idle. If the user asks to count cycles, we can use "run cycles"
if this is a per-task event, since the processor is running when
the task is running, by definition. We can't use "run cycles"
if the user asks for "cycles" on a system-wide counter.)
Fortunately the information we need is in the
event->attach_state field, so we just use that instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20101019055535.GA10398@drongo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Alexey Kardashevskiy <aik@au1.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just a minor cleanup patch that makes things easier to the following patches.
No functionality change in this patch.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-3-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ various fixes ]
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1287036094.7768.291.camel@yhuang-dev>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
The Freescale P1022DS has an on-chip video controller called the DIU, and a
driver for this device already exists. Update the platform file for the
P1022DS reference board to enable the driver, and update the defconfig for
Freescale MPC85xx boards to add the driver.
[Edited to resolve header add/add conflict and drop #define DEBUG.
-- broonie]
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure the new bluestone board is selected for the multiplatform defconfig.
Also build logfs and squashfs as modules.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add some comments to make sRIO registers map better readable.
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p5020 SoC from Freescale is the first 64-bit Book-E processor and
utilizes the two e5500 cores. Adding a defconfig that enables basic kernel
for e5500 based processors.
Also added the p5020 / e5500 support to the ppc64e defconfig.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On Freescale parts typically have TLB array for large mappings that we can
bolt the linear mapping into. We utilize the code that already exists
on PPC32 on the 64-bit side to setup the linear mapping to be cover by
bolted TLB entries. We utilize a quarter of the variable size TLB array
for this purpose.
Additionally, we limit the amount of memory to what we can cover via
bolted entries so we don't get secondary faults in the TLB miss
handlers. We should fix this limitation in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update setup_page_sizes() to support for a MMU v1.0 FSL style MMU
implementation. In such a processor, we don't have TLB0PS or EPTCFG
registers (and access to these registers may cause exceptions). We need
to parse the older format of TLBnCFG for page size support. Additionaly,
assume since we are an FSL implementation that we have 2 TLB arrays and
the second array contains the variable size pages.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new e5500 core is similar to the e500mc core but adds 64-bit
support. We support running it in 32-bit mode as it is identical to the
e500mc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It adds cache-sram support in P1/P2 QorIQ platforms as under:
* A small abstraction over powerpc's remote heap allocator
* Exports mpc85xx_cache_sram_alloc()/free() APIs
* Supports only one contiguous SRAM window
* Drivers can do the following in Kconfig to use these APIs
"select FSL_85XX_CACHE_SRAM if MPC85xx"
* Required SRAM size and the offset where SRAM should be mapped must be
provided at kernel command line as :
cache-sram-size=<value>
cache-sram-offset=<offset>
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The device tree for Freescale's P1022DS reference board is missing the node
for the ngPIXIS FPGA.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/kernel/paca.c: In function 'allocate_lppacas':
arch/powerpc/kernel/paca.c:111:1: error: parameter name omitted
arch/powerpc/kernel/paca.c:111:1: error: parameter name omitted
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On an arch 2.06 hypervisor, a pending perfmon interrupt will be delivered
to the hypervisor at any point the guest is running, regardless of
MSR[EE]. In order to reflect this interrupt, the hypervisor has to mask
the interrupt in PMGC0 -- and set MSRP[PMMP] to intercept futher guest
accesses to the PMRs to detect when to unmask (and prevent the guest from
unmasking early, or seeing inconsistent state).
This has the side effect of ignoring any changes the guest makes to
MSR[PMM], so wait until after the interrupt is clear, and thus the
hypervisor should have cleared MSRP[PMMP], before setting MSR[PMM]. The
counters wil not actually run until PMGC0[FAC] is cleared in
pmc_start_ctrs(), so this will not reduce the effectiveness of PMM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 'fsl,qoriq-gpio' compatiable to the list we search for to bind
against for mpc8xxx_gpio. This compatiable will be used on P1-P5xxx
QorIQ devices like P4080.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
First we check to see if we are the first core booting up. This
is accomplished by comparing the boot_cpuid with -1, if it is we
assume this is the first core coming up.
Secondly, we need to update the initial thread info structure
to reflect the actual cpu we are running on otherwise
smp_processor_id() and related functions will return the default
initialization value of the struct or 0.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Like the MPC8610 HPCD, the P1022DS ASoC DMA driver probes on individual DMA
channel nodes, so the DMA controller nodes' compatible string must be
listed in p1022_ds_ids[] to work.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The first global-utilities node might not contain the rstcr
property, so we should search all the nodes
Signed-off-by: Matthew McClintock <msm@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There exists a four line chunk of code, which when configured for
64 bit address space, can incorrectly set certain page flags during
the TLB creation. It turns out that this is code which isn't used,
but might still serve a purpose. Since it isn't obvious why it exists
or why it causes problems, the below description covers both in detail.
For powerpc bootstrap, the physical memory (at most 768M), is mapped
into the kernel space via the following path:
MMU_init()
|
+ adjust_total_lowmem()
|
+ map_mem_in_cams()
|
+ settlbcam(i, virt, phys, cam_sz, PAGE_KERNEL_X, 0);
On settlbcam(), the kernel will create TLB entries according to the flag,
PAGE_KERNEL_X.
settlbcam()
{
...
TLBCAM[index].MAS1 = MAS1_VALID
| MAS1_IPROT | MAS1_TSIZE(tsize) | MAS1_TID(pid);
^
These entries cannot be invalidated by the
kernel since MAS1_IPROT is set on TLB property.
...
if (flags & _PAGE_USER) {
TLBCAM[index].MAS3 |= MAS3_UX | MAS3_UR;
TLBCAM[index].MAS3 |= ((flags & _PAGE_RW) ? MAS3_UW : 0);
}
For classic BookE (flags & _PAGE_USER) is 'zero' so it's fine.
But on boards like the the Freescale P4080, we want to support 36-bit
physical address on it. So the following options may be set:
CONFIG_FSL_BOOKE=y
CONFIG_PTE_64BIT=y
CONFIG_PHYS_64BIT=y
As a result, boards like the P4080 will introduce PTE format as Book3E.
As per the file: arch/powerpc/include/asm/pgtable-ppc32.h
* #elif defined(CONFIG_FSL_BOOKE) && defined(CONFIG_PTE_64BIT)
* #include <asm/pte-book3e.h>
So PAGE_KERNEL_X is __pgprot(_PAGE_BASE | _PAGE_KERNEL_RWX) and the
book3E version of _PAGE_KERNEL_RWX is defined with:
(_PAGE_BAP_SW | _PAGE_BAP_SR | _PAGE_DIRTY | _PAGE_BAP_SX)
Note the _PAGE_BAP_SR, which is also defined in the book3E _PAGE_USER:
#define _PAGE_USER (_PAGE_BAP_UR | _PAGE_BAP_SR) /* Can be read */
So the possibility exists to wrongly assign the user MAS3_U<RWX> bits
to kernel (PAGE_KERNEL_X) address space via the following code fragment:
if (flags & _PAGE_USER) {
TLBCAM[index].MAS3 |= MAS3_UX | MAS3_UR;
TLBCAM[index].MAS3 |= ((flags & _PAGE_RW) ? MAS3_UW : 0);
}
Here is a dump of the TLB info from Simics with the above code present:
------
L2 TLB1
GT SSS UUU V I
Row Logical Physical SS TLPID TID WIMGE XWR XWR F P V
----- ----------------- ------------------- -- ----- ----- ----- --- --- - - -
0 c0000000-cfffffff 000000000-00fffffff 00 0 0 M XWR XWR 0 1 1
1 d0000000-dfffffff 010000000-01fffffff 00 0 0 M XWR XWR 0 1 1
2 e0000000-efffffff 020000000-02fffffff 00 0 0 M XWR XWR 0 1 1
Actually this conditional code was used for two legacy functions:
1: support KGDB to set break point.
KGDB already dropped this; now uses its core write to set break point.
2: io_block_mapping() to create TLB in segmentation size (not PAGE_SIZE)
for device IO space.
This use case is also removed from the latest PowerPC kernel.
However, there may still be a use case for it in the future, like
large user pages, so we can't remove it entirely. As an alternative,
we match on all bits of _PAGE_USER instead of just any bits, so the
case where just _PAGE_BAP_SR is set can't sneak through.
With this done, the TLB appears without U having XWR as below:
-------
L2 TLB1
GT SSS UUU V I
Row Logical Physical SS TLPID TID WIMGE XWR XWR F P V
----- ----------------- ------------------- -- ----- ----- ----- --- --- - - -
0 c0000000-cfffffff 000000000-00fffffff 00 0 0 M XWR 0 1 1
1 d0000000-dfffffff 010000000-01fffffff 00 0 0 M XWR 0 1 1
2 e0000000-efffffff 020000000-02fffffff 00 0 0 M XWR 0 1 1
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for MPC8308 P1M board.
Supported devices:
DUART
Dual Ethernet
NOR flash
Both I2C controllers
USB in peripheral mode
PCI Express
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we do an mpic_reset_core we need to make sure the dcache is flushed.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make kexec_down_cpus atmoic since it will be incremented by all cores as
they are coming down.
Remove duplicate calls to mpc85xx_smp_kexec_down, now it's called by the
crash and normal kexec pathway only once.
Increase the timeout to wait for other cores to shutdown.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We no longer need to call this explicitly as a generic version is called
by default.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Right now just the kexec crash pathway turns turns off the interrupts.
Pull that out and make a generic version for use elsewhere
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Export the global variable 'ppc_tb_freq', so that modules (like the Book-E
watchdog driver) can use it. To maintain consistency, ppc_proc_freq is
changed to a GPL-only export. This is okay, because any module that needs
this symbol should be an actual Linux driver, which must be GPL-licensed.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following commit broke 83xx because it assumed the 83xx platforms
exposed the "IMMR" address in BAR0 like the 85xx/86xx/QoriQ devices do:
commit 3da34aae03
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Tue May 12 15:51:56 2009 -0500
powerpc/fsl: Support unique MSI addresses per PCIe Root Complex
However that is not true, so we have to search through the inbound
window settings on 83xx to find which one matches the IMMR address to
determine its PCI address.
Reported-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds CPU, device tree, defconfig and bluestone board
support for APM821xx SoC.
Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Replace EXTRA_CFLAGS with ccflags-y and EXTRA_AFLAGS with asflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The default for llseek is changing, so we need
explicit operations everywhere.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Current firmware only allows us to send IRQs to the first processor or
all processors. We currently check to see if the passed in mask is equal
to the all_mask, but the firmware is only considering whether the
request is for the equivalent of the possible_mask. Thus, we think the
request is for some subset of CPUs and only assign IRQs to the first CPU
(on systems without irqbalance running) as evidenced by
/proc/interrupts. By using possible_mask instead, we account for this
and proper interleaving of interrupts occurs.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use set_dma_ops and remove unused oddly-named temp pointer sd.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While looking at some code paths I came across this code that zeros
memory then copies over the entire length.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Release the TCE table as the XXX suggests, except on FW_FEATURE_ISERIES,
where the tables are allocated globally and reused.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel doc for device_register (and device_initialize) very clearly
state to call put_device not kfree after calling, even on error.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current check is wrong because it does not take the DMA offset intot
account, and in the case of a driver which doesn't actually support
64bits would falsely report that device as working.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The table offset is in entries, each of which imply a dma address of
an IOMMU page.
Also, we should check the device can reach the whole IOMMU table.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
BUID_HI and BUID_LO are used to pass data to call_rtas, which expects
ints or u32s. But the macro doesn't cast the return, so the result is
still u64. Use the upper_32_bits and lower_32_bits macros that have been
added to kernel.h.
Found by getting printf format errors trying to debug print the args, no
actual code change for 64 bit kernels where the macros are actually
used.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In this case, a device_node structure is stored in another structure that
is then freed without first decrementing the reference count of the
device_node structure.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression x;
identifier f;
position p1,p2;
@@
x@p1->f = \(of_find_node_by_path\|of_find_node_by_name\|of_find_node_by_phandle\|of_get_parent\|of_get_next_parent\|of_get_next_child\|of_find_compatible_node\|of_match_node\|of_find_node_by_type\|of_find_node_with_property\|of_find_matching_node\|of_parse_phandle\|of_node_get\)(...);
... when != of_node_put(x)
kfree@p2(x)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
cocci.print_main("call",p1)
cocci.print_secs("free",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable partition migration in the kernel. To do this a new sysfs file,
/sys/kernel/mobility/migration, is created. In order to initiate a migration
the stream id (generated by the HMC managing the system) is written to this
file.
After a migration occurs, and what is the majority of this code, the device
tree needs to be updated for the new system the partition is running on. This
is done via the ibm,update-nodes and ibm,update-properties rtas calls which
return information regarding which nodes and properties of the device tree
are to be added/removed/updated.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Export the rtas_ibm_suspend_me() routine. This is needed to perform
partition migration in the kernel.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Export routines associated with adding and removing device tree nodes on
pseries needed for device tree updating.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Also modifiy the document of cell-index in SPI controller. Add the
SPI flash(s25fl128p01) support on p4080ds and mpc8536ds board.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We need to round memory regions correctly -- specifically, we need to
round reserved region in the more expansive direction (lower limit
down, upper limit up) whereas usable memory regions need to be rounded
in the more restrictive direction (lower limit up, upper limit down).
This introduces two set of inlines:
memblock_region_memory_base_pfn()
memblock_region_memory_end_pfn()
memblock_region_reserved_base_pfn()
memblock_region_reserved_end_pfn()
Although they are antisymmetric (and therefore are technically
duplicates) the use of the different inlines explicitly documents the
programmer's intention.
The lack of proper rounding caused a bug on ARM, which was then found
to also affect other architectures.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4CB4CDFD.4020105@kernel.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
arch/powerpc/platforms/built-in.o:(.toc1+0x18): undefined reference to `__early_start'
This is due to the 85xx/smp.c not handling the 64-bit side properly. We
need to set the entry point for secondary cores on ppc64e to
generic_secondary_smp_init instead of __early_start that we due on ppc32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The speed and clock of the serial ports is retrieved from the device
tree in both the PowerPC legacy serial code and the Open Firmware serial
driver, therefore they need to handle the fact that the device tree is
always big endian, while the CPU may not be.
Also fix other device tree references in the legacy serial code.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Now that the generic DMAEngine API has support for scatterlist to
scatterlist copying, the device_prep_slave_sg() portion of the
DMA_SLAVE API is no longer necessary and has been removed.
However, the device_control() portion of the DMA_SLAVE API is still
useful to control device specific parameters, such as externally
controlled DMA transfers and maximum burst length.
A special dma_ctrl_cmd has been added to enable externally controlled
DMA transfers. This is currently specific to the Freescale DMA
controller, but can easily be made generic when another user is found.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
Since powerpc uses -Werror on arch powerpc, the build was broken like
this:
cc1: warnings being treated as errors
arch/powerpc/kernel/module.c: In function 'module_finalize':
arch/powerpc/kernel/module.c:66: error: unused variable 'err'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With all the recent module loading cleanups, we've minimized the code
that sits under module_mutex, fixing various deadlocks and making it
possible to do most of the module loading in parallel.
However, that whole conversion totally missed the rather obscure code
that adds a new module to the list for BUG() handling. That code was
doubly obscure because (a) the code itself lives in lib/bugs.c (for
dubious reasons) and (b) it gets called from the architecture-specific
"module_finalize()" rather than from generic code.
Calling it from arch-specific code makes no sense what-so-ever to begin
with, and is now actively wrong since that code isn't protected by the
module loading lock any more.
So this commit moves the "module_bug_{finalize,cleanup}()" calls away
from the arch-specific code, and into the generic code - and in the
process protects it with the module_mutex so that the list operations
are now safe.
Future fixups:
- move the module list handling code into kernel/module.c where it
belongs.
- get rid of 'module_bug_list' and just use the regular list of modules
(called 'modules' - imagine that) that we already create and maintain
for other reasons.
Reported-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The logic to distinguish marked instruction events from ordinary events
on PPC970 and derivatives was flawed. The result is that instruction
sampling didn't get enabled in the PMU for some marked instruction
events, so they would never trigger. This fixes it by adding the
appropriate break statements in the switch statement.
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make sigreturn zero regs->trap, make do_signal() do the same on all
paths. As it is, signal interrupting e.g. read() from fd 512 (==
ERESTARTSYS) with another signal getting unblocked when the first
handler finishes will lead to restart one insn earlier than it ought
to. Same for multiple signals with in-kernel handlers interrupting
that sucker at the same time. Same for multiple signals of any kind
interrupting that sucker on 64bit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default for llseek is changing, so we need
explicit operations everywhere.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: linuxppc-dev@ozlabs.org
compat_alloc_user_space() expects the caller to independently call
access_ok() to verify the returned area. A missing call could
introduce problems on some architectures.
This patch incorporates the access_ok() check into
compat_alloc_user_space() and also adds a sanity check on the length.
The existing compat_alloc_user_space() implementations are renamed
arch_compat_alloc_user_space() and are used as part of the
implementation of the new global function.
This patch assumes NULL will cause __get_user()/__put_user() to either
fail or access userspace on all architectures. This should be
followed by checking the return value of compat_access_user_space()
for NULL in the callers, at which time the access_ok() in the callers
can also be removed.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <stable@kernel.org>
Fix memblock API change fallout in the WII code.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: linux-mm@kvack.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <4C8B2AFA.2000705@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The GPIO controller of MPC512x is slightly different from
8xxx GPIO controllers. The register interface is the same
except the external interrupt control register. The MPC512x
GPIO controller differentiates between four interrupt event
types and therefore provides two interrupt control registers,
GPICR1 and GPICR2. GPIO[0:15] interrupt event types are
configured in GPICR1 register, GPIO[16:31] - in GPICR2 register.
This patch adds MPC512x speciffic set_type() callback and
updates config file and comments. Additionally the gpio chip
registration function is changed to use for_each_matching_node()
preventing multiple registration if a node claimes compatibility
with another gpio controller type.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The slab.h header is required to use the kmalloc() family of functions.
Due to recent kernel changes, this header must be directly included by
code that calls into the memory allocator.
Without this patch, any code which includes this header fails to build.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace pmu::{enable,disable,start,stop,unthrottle} with
pmu::{add,del,start,stop}, all of which take a flags argument.
The new interface extends the capability to stop a counter while
keeping it scheduled on the PMU. We replace the throttled state with
the generic stopped state.
This also allows us to efficiently stop/start counters over certain
code paths (like IRQ handlers).
It also allows scheduling a counter without it starting, allowing for
a generic frozen state (useful for rotating stopped counters).
The stopped state is implemented in two different ways, depending on
how the architecture implemented the throttled state:
1) We disable the counter:
a) the pmu has per-counter enable bits, we flip that
b) we program a NOP event, preserving the counter state
2) We store the counter state and ignore all read/overflow events
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Yanmin <yanmin_zhang@linux.intel.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Michael Cree <mcree@orcon.net.nz>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the current perf_disable() usage is only an optimization,
remove it for now. This eases the removal of the __weak
hw_perf_enable() interface.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Yanmin <yanmin_zhang@linux.intel.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Michael Cree <mcree@orcon.net.nz>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simple registration interface for struct pmu, this provides the
infrastructure for removing all the weak functions.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus <paulus@samba.org>
Cc: stephane eranian <eranian@googlemail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Yanmin <yanmin_zhang@linux.intel.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Michael Cree <mcree@orcon.net.nz>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tighten up time timing around the gpio reset functionality. Add a 200ns
delay before remuxing the pins back to ac97 to comply with the ac97 spec.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This function is implemented as though the function of_get_next_child does
not increment the reference count of its result, but actually it does.
Thus the patch adds of_node_put in error handling code and drops a call to
of_node_get.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E1;
position p1,p2;
@@
x@p1 = of_get_next_child(...);
... when != x = E1
of_node_get@p2(x)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
cocci.print_main("call",p1)
cocci.print_secs("get",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Replace the BOOK3S_64 specific mtmsrd with the generic MTMSRD macro.
Only enable ldstfp when CONFIG_PPC_FPU is set.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/mm/mmu_context_nohash.c assumes the boot cpu
will always have smp_processor_id() == 0. This patch fixes
that assumption
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch wires up the various socket system calls on PowerPC so that
userspace can call them directly, rather than by going through the
multiplexed socketcall system call.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a call to of_node_put in the error handling code following a call to
of_find_node_by_type.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1,E2;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
|of_find_node_by_type
|of_find_node_with_property
|of_find_matching_node
|of_parse_phandle
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
(
E2 = x;
|
of_node_put(x);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add calls to of_node_put in the error handling code following calls to
of_find_node_by_path and of_find_node_by_phandle.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
of_node_put(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a call to of_node_put in the error handling code following a call to
of_find_node_by_phandle.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
of_node_put(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a call to of_node_put in the error handling code following a call to
of_find_node_by_path.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
of_node_put(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI-Express bus off the U4/CPC945 bridge supports direct DMA to
all of memory, bypassing the DART iommu, for 64-bit capable devices.
This adds support for it on Bimini and Apple Quad G5's in order to
improve DMA performances of cards using that slot (the x16 graphics
slot). Tested with an Intel ixgbe 10GE card.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some platforms may want to override dma_set_mask() to take into
account some specific "features" such as the availability of
a direct-map window in addition to an iommu.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch removes all explicit tests for the TIF_32BIT flag
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Neither lfs nor stfs touch the fpscr, so remove the restore/save of it
around them.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the cpu accounting code uses the hypervisor dispatch trace log
now when CONFIG_VIRT_CPU_ACCOUNTING = y, the previous commit disabled
access to it via files in the /sys/kernel/debug/powerpc/dtl/ directory
in that case. This restores those files.
To do this, we now have a hook that the cpu accounting code will call
as it processes each entry from the hypervisor dispatch trace log.
The code in dtl.c now uses that to fill up its ring buffer, rather
than having the hypervisor fill the ring buffer directly.
This also fixes dtl_file_read() to handle overflow conditions a bit
better and adds a spinlock to ensure that race conditions (multiple
processes opening or reading the file concurrently) are handled
correctly.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, when CONFIG_VIRT_CPU_ACCOUNTING is enabled, we use the
PURR register for measuring the user and system time used by
processes, as well as other related times such as hardirq and
softirq times. This turns out to be quite confusing for users
because it means that a program will often be measured as taking
less time when run on a multi-threaded processor (SMT2 or SMT4 mode)
than it does when run on a single-threaded processor (ST mode), even
though the program takes longer to finish. The discrepancy is
accounted for as stolen time, which is also confusing, particularly
when there are no other partitions running.
This changes the accounting to use the timebase instead, meaning that
the reported user and system times are the actual number of real-time
seconds that the program was executing on the processor thread,
regardless of which SMT mode the processor is in. Thus a program will
generally show greater user and system times when run on a
multi-threaded processor than on a single-threaded processor.
On pSeries systems on POWER5 or later processors, we measure the
stolen time (time when this partition wasn't running) using the
hypervisor dispatch trace log. We check for new entries in the
log on every entry from user mode and on every transition from
kernel process context to soft or hard IRQ context (i.e. when
account_system_vtime() gets called). So that we can correctly
distinguish time stolen from user time and time stolen from system
time, without having to check the log on every exit to user mode,
we store separate timestamps for exit to user mode and entry from
user mode.
On systems that have a SPURR (POWER6 and POWER7), we read the SPURR
in account_system_vtime() (as before), and then apportion the SPURR
ticks since the last time we read it between scaled user time and
scaled system time according to the relative proportions of user
time and system time over the same interval. This avoids having to
read the SPURR on every kernel entry and exit. On systems that have
PURR but not SPURR (i.e., POWER5), we do the same using the PURR
rather than the SPURR.
This disables the DTL user interface in /sys/debug/kernel/powerpc/dtl
for now since it conflicts with the use of the dispatch trace log
by the time accounting code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This arranges for the lppaca structs for most cpus to be dynamically
allocated in the same manner as the paca structs. If we don't include
support for legacy iSeries, only the first lppaca is statically
allocated; the rest are dynamically allocated. If we include legacy
iSeries support, then we statically allocate the first 64 lppaca
structs, since the iSeries hypervisor requires that the lppaca
structs be present in the data section of the kernel image, but
legacy iSeries supports at most 64 cpus.
With CONFIG_NR_CPUS, the kernel image size for a typical pSeries config
went from:
text data bss dec hex filename
9524478 4734564 8469944 22728986 15ad11a ../test-1024/vmlinux
to:
text data bss dec hex filename
9524482 3751508 8469944 21745934 14bd10e ../test-1024/vmlinux
a reduction of 983052 bytes overall.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we have the lppaca structs as a simple array of NR_CPUS
entries, taking up space in the data section of the kernel image.
In future we would like to allocate them dynamically, so this
abstracts out the accesses to the array, making it easier to
change how we locate the lppaca for a given cpu in future.
Specifically, lppaca[cpu] changes to lppaca_of(cpu).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simple cleanup by moving arch_sd_sibling_asym_packing from process.c to
smp.c to save an #ifdef CONFIG_SMP
No functionality change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a check for the stack canary when we oops, similar to x86. This should make
it clear that we overran our stack:
Unable to handle kernel paging request for data at address 0x24652f63700ac689
Faulting instruction address: 0xc000000000063d24
Thread overran stack, or stack corrupted
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The POWER architecture does not require stcx to check that it is operating
on the same address as the larx. This means it is possible for an
an exception handler to execute a larx, get a reservation, decide
not to do the stcx and then return back with an active reservation. If the
interrupted code was in the middle of a larx/stcx sequence the stcx could
incorrectly succeed.
All recent POWER CPUs check the address before letting the stcx succeed
so we can create a CPU feature and nop it out. As Ben suggested, we can
only do this in our syscall path because there is a remote possibility
some kernel code gets interrupted by an exception that ends up operating
on the same cacheline.
Thanks to Paul Mackerras and Derek Williams for the idea.
To test this I used a very simple null syscall (actually getppid) testcase
at http://ozlabs.org/~anton/junkcode/null_syscall.c
I tested against 2.6.35-git10 with the following changes against the
pseries_defconfig:
CONFIG_VIRT_CPU_ACCOUNTING=n
CONFIG_AUDIT=n
CONFIG_PPC_4K_PAGES=n
CONFIG_PPC_64K_PAGES=y
CONFIG_FORCE_MAX_ZONEORDER=9
CONFIG_PPC_SUBPAGE_PROT=n
CONFIG_FUNCTION_TRACER=n
CONFIG_FUNCTION_GRAPH_TRACER=n
CONFIG_IRQSOFF_TRACER=n
CONFIG_STACK_TRACER=n
to remove the overhead of virtual CPU accounting, syscall auditing and
the ftrace mcount tracers. 64kB pages were enabled to minimise TLB misses.
POWER6: +8.2%
POWER7: +7.0%
Another suggestion was to use a larx to something in the L1 instead of a stcx.
This was almost as fast as removing the larx on POWER6, but only 3.5% faster
on POWER7. We can use this to speed up the reservation clear in our
exception exit code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the equivalent of csum_and_copy_from_user for the receive side so we
can copy and checksum in one pass. It is modelled on the generic checksum
routine.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We use the same core loop as the new csum_partial, adding in the
stores and exception handling code. To keep things simple we do all the
exception fixup in csum_and_copy_from_user. This wrapper function is
modelled on the generic checksum code and is careful to always calculate
a complete checksum even if we only copied part of the data to userspace.
To test this I forced checksumming on over loopback and ran socklib (a
simple TCP benchmark). On a POWER6 575 throughput improved by 19% with
this patch. If I forced both the sender and receiver onto the same cpu
(with the hope of shifting the benchmark from being cache bandwidth limited
to cpu limited), adding this patch improved performance by 55%
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The main loop of csum_partial runs very slowly on recent POWER CPUs. After some
analysis on both POWER6 and POWER7 I came up with routine below. First we get
the source aligned to a double word, ignoring any odd alignment to keep things
simple. Then we do 64 bytes at a time, with an entry and exit limb of a further
64 bytes. On both POWER6 and POWER7 this should be as fast as we can go since
we are limited by the latency of the adde instructions.
To test this I forced checksumming on over loopback and ran socklib (a
simple TCP benchmark). On a POWER6 575 throughput improved by 11% with
this patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The dlpar code can cause a deadlock to occur when making the RTAS
configure-connector call. This occurs because we make kmalloc calls,
which can block, while parsing the rtas_data_buf and holding the
rtas_data_buf_lock. This an cause issues if someone else attempts
to grab the rtas_data_bug_lock.
This patch alleviates this issue by copying the contents of the rtas_data_buf
to a local buffer before parsing. This allows us to only hold the
rtas_data_buf_lock around the RTAS configure-connector calls.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
clk_get() should return an ERR_PTR value on error, not NULL.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is needed for proper PCI-E support on P1021 SoCs.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
of_node_put(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function of_iomap returns the result of calling ioremap, so iounmap
should be called on the result in the error handling code, as done in the
normal exit of the function.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
identifier l;
statement S;
@@
*x = of_iomap(...);
... when != iounmap(x)
when != if (...) { ... iounmap(x); ... }
when != E = x
when any
(
if (x == NULL) S
|
if (...) {
... when != iounmap(x)
when != if (...) { ... iounmap(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
)
... when != x = E1
when any
iounmap(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixes the following compile problem on E500 platforms:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_mcheck_exception':
arch/powerpc/sysdev/fsl_rio.c:248: error: 'MCSR_MASK' undeclared (first use in this function)
Also fixes the compile problem on non-E500 platforms.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/p1022_ds.c:22:23: error: linux/lmb.h: No such file or directory
arch/powerpc/platforms/85xx/p1022_ds.c: In function 'p1022_ds_setup_arch':
arch/powerpc/platforms/85xx/p1022_ds.c💯 error: implicit declaration of function 'memblock_end_of_DRAM'
arch/powerpc/platforms/85xx/p1022_ds.c: At top level:
arch/powerpc/platforms/85xx/p1022_ds.c:147: error: 'udbg_progress' undeclared here (not in a function)
make[2]: *** [arch/powerpc/platforms/85xx/p1022_ds.o] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 99d8238f berobbed the for_each loop of its iterator! Let's be
nice and give it back, so it compiles for us.
CC: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In f761622e59 we changed
early_setup_secondary so it's called using the proper kernel stack
rather than the emergency one.
Unfortunately, this stack pointer can't be used when translation is off
on PHYP as this stack pointer might be outside the RMO. This results in
the following on all non zero cpus:
cpu 0x1: Vector: 300 (Data Access) at [c00000001639fd10]
pc: 000000000001c50c
lr: 000000000000821c
sp: c00000001639ff90
msr: 8000000000001000
dar: c00000001639ffa0
dsisr: 42000000
current = 0xc000000016393540
paca = 0xc000000006e00200
pid = 0, comm = swapper
The original patch was only tested on bare metal system, so it never
caught this problem.
This changes __secondary_start so that we calculate the new stack
pointer but only start using it after we've called early_setup_secondary.
With this patch, the above problem goes away.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 0fe1ac48 ("powerpc/perf_event: Fix oops due to
perf_event_do_pending call") moved the call to perf_event_do_pending
in timer_interrupt() down so that it was after the irq_enter() call.
Unfortunately this moved it after the code that checks whether it
is time for the next decrementer clock event. The result is that
the call to perf_event_do_pending() won't happen until the next
decrementer clock event is due. This was pointed out by Milton
Miller.
This fixes it by moving the check for whether it's time for the
next decrementer clock event down to the point where we're about
to call the event handler, after we've called perf_event_do_pending.
This has the side effect that on old pre-Core99 Powermacs where we
use the ppc_n_lost_interrupts mechanism to replay interrupts, a
replayed interrupt will incur a little more latency since it will
now do the code from the irq_enter down to the irq_exit, that it
used to skip. However, these machines are now old and rare enough
that this doesn't matter. To make it clear that ppc_n_lost_interrupts
is only used on Powermacs, and to speed up the code slightly on
non-Powermac ppc32 machines, the code that tests ppc_n_lost_interrupts
is now conditional on CONFIG_PMAC as well as CONFIG_PPC32.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Call kexec purgatory code correctly. We were getting lucky before.
If you examine the powerpc 32bit kexec "purgatory" code you will
see it expects the following:
>From kexec-tools: purgatory/arch/ppc/v2wrap_32.S
-> calling convention:
-> r3 = physical number of this cpu (all cpus)
-> r4 = address of this chunk (master only)
As such, we need to set r3 to the current core, r4 happens to be
unused by purgatory at the moment but we go ahead and set it
here as well
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
MPIC_U3_HT_IRQS is selected both by PPC_PMAC64 and PPC_MAPLE, but depends
on PPC_MAPLE, so a PPC_PMAC64-only config gets this warning:
warning: (PPC_PMAC64 && PPC_PMAC && POWER4 || PPC_MAPLE && PPC64 && PPC_BOOK3S) selects MPIC_U3_HT_IRQS which has unmet direct dependencies (PPC_MAPLE)
Fix that by removing the dependency on PPC_MAPLE.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pci_device_to_OF_node() can return null, and list_for_each_entry will
never enter the loop when dev is NULL, so it looks like this test is
a typo.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit e32e78c5ee
(powerpc: fix build with make 3.82) introduced a
typo in uImage target and broke building uImage:
make: *** No rule to make target `uImage'. Stop.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As early setup calls down to slb_initialize(), we must have kstack
initialised before checking "should we add a bolted SLB entry for our kstack?"
Failing to do so means stack access requires an SLB miss exception to refill
an entry dynamically, if the stack isn't accessible via SLB(0) (kernel text
& static data). It's not always allowable to take such a miss, and
intermittent crashes will result.
Primary CPUs don't have this issue; an SLB entry is not bolted for their
stack anyway (as that lives within SLB(0)). This patch therefore only
affects the init of secondaries.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When looking at some issues with the virtual ethernet driver I noticed
that TCE allocation was following a very strange pattern:
address 00e9000 length 2048
address 0409000 length 2048 <-----
address 0429000 length 2048
address 0449000 length 2048
address 0469000 length 2048
address 0489000 length 2048
address 04a9000 length 2048
address 04c9000 length 2048
address 04e9000 length 2048
address 4009000 length 2048 <-----
address 4029000 length 2048
Huge unexplained gaps in what should be an empty TCE table. It turns out
it_blocksize, the amount we want to align the next allocation to, was
c0000000fe903b20. Completely bogus.
Initialise it to something reasonable in the VIO IOMMU code, and use kzalloc
everywhere to protect against this when we next add a non compulsary
field to iommu code and forget to initialise it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I'm sick of seeing ppc64_runlatch_off in our profiles, so inline it
into the callers. To avoid a mess of circular includes I didn't add
it as an inline function.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The 'smt_enabled=X' boot option does not handle values of X > 2.
For Power 7 processors with smt modes of 0,1,2,3, and 4 this does
not work. This patch allows the smt_enabled option to be set to
any value limited to a max equal to the number of threads per
core.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All IRQs are migrated away from a CPU that is being offlined so the
following messages suggest a problem when the system is behaving as
designed:
IRQ 262 affinity broken off cpu 1
IRQ 17 affinity broken off cpu 0
IRQ 18 affinity broken off cpu 0
IRQ 19 affinity broken off cpu 0
IRQ 256 affinity broken off cpu 0
IRQ 261 affinity broken off cpu 0
IRQ 262 affinity broken off cpu 0
Don't print these messages when the CPU is not online.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Acked-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Fontenot <nfont@austin.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During CPU offline/online tests __cpu_up would flood the logs with
the following message:
Processor 0 found.
This provides no useful information to the user as there is no context
provided, and since the operation was a success (to this point) it is expected
that the CPU will come back online, providing all the feedback necessary.
Change the "Processor found" message to DBG() similar to other such messages in
the same function. Also, add an appropriate log level for the "Processor is
stuck" message.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Acked-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Fontenot <nfont@austin.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
start_secondary() is called shortly after _start and also via
cpu_idle()->cpu_die()->pseries_mach_cpu_die()
start_secondary() expects a preempt_count() of 0. pseries_mach_cpu_die() is
called via the cpu_idle() routine with preemption disabled, resulting in the
following repeating message during rapid cpu offline/online tests
with CONFIG_PREEMPT=y:
BUG: scheduling while atomic: swapper/0/0x00000002
Modules linked in: autofs4 binfmt_misc dm_mirror dm_region_hash dm_log [last unloaded: scsi_wait_scan]
Call Trace:
[c00000010e7079c0] [c0000000000133ec] .show_stack+0xd8/0x218 (unreliable)
[c00000010e707aa0] [c0000000006a47f0] .dump_stack+0x28/0x3c
[c00000010e707b20] [c00000000006e7a4] .__schedule_bug+0x7c/0x9c
[c00000010e707bb0] [c000000000699d9c] .schedule+0x104/0x800
[c00000010e707cd0] [c000000000015b24] .cpu_idle+0x1c4/0x1d8
[c00000010e707d70] [c0000000006aa1b4] .start_secondary+0x398/0x3d4
[c00000010e707e30] [c000000000008278] .start_secondary_resume+0x10/0x14
Move the cpu_die() call inside the existing preemption enabled block of
cpu_idle(). This is safe as the idle task is affined to a single CPU so the
debug_smp_processor_id() tests (from cpu_should_die()) won't trigger as we are
in a "migration disabled" region.
Signed-off-by: Darren Hart <dvhltc@us.ibm.com>
Acked-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Fontenot <nfont@austin.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
list_for_each_entry binds its first argument to a non-null value, and thus
any null test on the value of that argument is superfluous.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
iterator I;
expression x,E,E1,E2;
statement S,S1,S2;
@@
I(x,...) { <...
- if (x != NULL || ...)
S
...> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
for_each_node_by_name binds its first argument to a non-null value, and
thus any null test on the value of that argument is superfluous.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
iterator I;
expression x,E;
@@
I(x,...) { <...
(
- (x != NULL) &&
E
...> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
for_each_node_by_name only exits when its first argument is NULL, and a
subsequent call to of_node_put on that argument is unnecessary.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
iterator name for_each_node_by_name;
expression np,E;
identifier l;
@@
for_each_node_by_name(np,...) {
... when != break;
when != goto l;
}
... when != np = E
- of_node_put(np);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During kdump we run the crash handlers first then stop all other CPUs.
We really want to stop all CPUs as close to the fail as possible and also
have a very controlled environment for running the crash handlers, so it
makes sense to reverse the order.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code is wrapped in an #if 0, but it's wrong so we may as well fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use is_32bit_task() helper to test 32 bit binary.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some modules (like eHCA) want to map all of kernel memory, for this to
work with a relocated kernel, we need to export kernstart_addr so
modules can use PHYSICAL_START and memstart_addr so they could use
MEMORY_START. Note that the 32bit code already exports these symbols.
Signed-off-By: Sonny Rao <sonnyrao@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This makes the 64-bit kernel use 64-bit signed integers for the counter
(effectively supporting 32-bit of active count in the semaphore), thus
avoiding things like overflow of the mmap_sem if you use a really crazy
number of threads
Note: Ideally the type in the structure should be atomic_long_t rather
than "long". However, there's some nasty issues with that. It needs to
be initialized statically -and- lib/rwsem.c does things like
sem->count = RWSEM_UNLOCKED_VALUE;
Now, if you mix in the fact that atomic_* types are actually structures
with one member and note typedefs of a scalar, it makes its really nasty.
So I stuck to what we did before using a long and casts for now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The interrupt stacks need to be indexed by the physical cpu since the
critical, debug and machine check handlers use the contents of SPRN_PIR to
index the critirq_ctx, dbgirq_ctx, and mcheckirq_ctx arrays.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
There are two entries for .cpu_user_features in
arch/powerpc/kernel/cputable.c. Remove the one that doesn't belong
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Clear the machine check syndrom register before enabling machine check
interrupts. The initial state of the tlb can lead to parity errors being
flagged early after a cold boot.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Device tree update for the Applied micro processor 460ex on-chip SATA
Signed-off-by: Rupjyoti Sarmah <rsarmah@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Noone is using tty argument so let's get rid of it.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Store the kernel and user contexts from the generic layer instead
of archs, this gathers some repetitive code.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Borislav Petkov <bp@amd64.org>
- Most archs use one callchain buffer per cpu, except x86 that needs
to deal with NMIs. Provide a default perf_callchain_buffer()
implementation that x86 overrides.
- Centralize all the kernel/user regs handling and invoke new arch
handlers from there: perf_callchain_user() / perf_callchain_kernel()
That avoid all the user_mode(), current->mm checks and so...
- Invert some parameters in perf_callchain_*() helpers: entry to the
left, regs to the right, following the traditional (dst, src).
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Borislav Petkov <bp@amd64.org>
callchain_store() is the same on every archs, inline it in
perf_event.h and rename it to perf_callchain_store() to avoid
any collision.
This removes repetitive code.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Borislav Petkov <bp@amd64.org>
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:
arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type
This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to. This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel(). A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().
do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.
Further kernel_execve() and sys_execve() need to be changed to match.
This has been test built on x86_64, frv, arm and mips.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
Mark arguments to certain system calls as being const where they should be but
aren't. The list includes:
(*) The filename arguments of various stat syscalls, execve(), various utimes
syscalls and some mount syscalls.
(*) The filename arguments of some syscall helpers relating to the above.
(*) The buffer argument of various write syscalls.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for adding "status = disabled" to an SSI node to incidate that it
is not wired on the board. This replaces the not-so-intuitive previous method
of omitting a codec-handle property.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The immap_86xx.h header file only defines one data structure: the "global
utilities" register set found on Freescale PowerPC SOCs. Rename this file
to fsl_guts.h to reflect its true purpose, and extend it to cover the "GUTS"
register set on 85xx chips.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now each architecture has the own dma_get_cache_alignment implementation.
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
define it as ARCH_KMALLOC_MINALIGN (it's used to make sure that malloc'ed
buffer is DMA-safe; the buffer doesn't share a cache with the others). So
we can unify dma_get_cache_alignment implementations.
This patch:
dma_get_cache_alignment() needs to know if an architecture defines
ARCH_KMALLOC_MINALIGN or not (needs to know if architecture has DMA
alignment restriction). However, slab.h define ARCH_KMALLOC_MINALIGN if
architectures doesn't define it.
Let's rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN.
ARCH_KMALLOC_MINALIGN is used only in the internals of slab/slob/slub
(except for crypto).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
P4080 ESDHC controller does not support 1.8V and 3.0V voltage. but the
host controller capabilities register wrongly set the bits. This patch
adds the workaround to correct the weird voltage setting bits. Only 3.3V
voltage is supported for P4080 ESDHC controller.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Jerry Huang <Chang-Ming.Huang@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Jerry Huang <Chang-Ming.Huang@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
This patch is against the 2.6.34 source.
Paraphrased from the 1989 BSD patch by David Borman @ cray.com:
These are the changes needed for the kernel to support
LINEMODE in the server.
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
New ioctl:
TIOCSIG Generate a signal to processes in the
current process group of the pty.
There is a new mode for packet driver, the TIOCPKT_IOCTL bit.
When packet mode is turned on in the pty, and the EXTPROC bit
is set, then whenever the state of the pty is changed, the
next read on the master side of the pty will have the TIOCPKT_IOCTL
bit set. This allows the process on the server side of the pty
to know when the state of the terminal has changed; it can then
issue the appropriate ioctl to retrieve the new state.
Since the original BSD patches accompanied the source code for telnet
I've left that reference here, but obviously the feature is useful for
any remote terminal protocol, including ssh.
The corresponding feature has existed in the BSD tty driver since 1989.
For historical reference, a good copy of the relevant files can be found
here:
http://anonsvn.mit.edu/viewvc/krb5/trunk/src/appl/telnet/?pathrev=17741
Signed-off-by: Howard Chu <hyc@symas.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
no need for list_for_each_entry_safe()/resetting with superblock list
Fix sget() race with failing mount
vfs: don't hold s_umount over close_bdev_exclusive() call
sysv: do not mark superblock dirty on remount
sysv: do not mark superblock dirty on mount
btrfs: remove junk sb_dirt change
BFS: clean up the superblock usage
AFFS: wait for sb synchronization when needed
AFFS: clean up dirty flag usage
cifs: truncate fallout
mbcache: fix shrinker function return value
mbcache: Remove unused features
add f_flags to struct statfs(64)
pass a struct path to vfs_statfs
update VFS documentation for method changes.
All filesystems that need invalidate_inode_buffers() are doing that explicitly
convert remaining ->clear_inode() to ->evict_inode()
Make ->drop_inode() just return whether inode needs to be dropped
fs/inode.c:clear_inode() is gone
fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
...
Fix up trivial conflicts in fs/nilfs2/super.c
kunmap_atomic() is currently at level -4 on Rusty's "Hard To Misuse"
list[1] ("Follow common convention and you'll get it wrong"), except in
some architectures when CONFIG_DEBUG_HIGHMEM is set[2][3].
kunmap() takes a pointer to a struct page; kunmap_atomic(), however, takes
takes a pointer to within the page itself. This seems to once in a while
trip people up (the convention they are following is the one from
kunmap()).
Make it much harder to misuse, by moving it to level 9 on Rusty's list[4]
("The compiler/linker won't let you get it wrong"). This is done by
refusing to build if the type of its first argument is a pointer to a
struct page.
The real kunmap_atomic() is renamed to kunmap_atomic_notypecheck()
(which is what you would call in case for some strange reason calling it
with a pointer to a struct page is not incorrect in your code).
The previous version of this patch was compile tested on x86-64.
[1] http://ozlabs.org/~rusty/index.cgi/tech/2008-04-01.html
[2] In these cases, it is at level 5, "Do it right or it will always
break at runtime."
[3] At least mips and powerpc look very similar, and sparc also seems to
share a common ancestor with both; there seems to be quite some
degree of copy-and-paste coding here. The include/asm/highmem.h file
for these three archs mention x86 CPUs at its top.
[4] http://ozlabs.org/~rusty/index.cgi/tech/2008-03-30.html
[5] As an aside, could someone tell me why mn10300 uses unsigned long as
the first parameter of kunmap_atomic() instead of void *?
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Cc: Russell King <linux@arm.linux.org.uk> (arch/arm)
Cc: Ralf Baechle <ralf@linux-mips.org> (arch/mips)
Cc: David Howells <dhowells@redhat.com> (arch/frv, arch/mn10300)
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> (arch/mn10300)
Cc: Kyle McMartin <kyle@mcmartin.ca> (arch/parisc)
Cc: Helge Deller <deller@gmx.de> (arch/parisc)
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> (arch/parisc)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> (arch/powerpc)
Cc: Paul Mackerras <paulus@samba.org> (arch/powerpc)
Cc: "David S. Miller" <davem@davemloft.net> (arch/sparc)
Cc: Thomas Gleixner <tglx@linutronix.de> (arch/x86)
Cc: Ingo Molnar <mingo@redhat.com> (arch/x86)
Cc: "H. Peter Anvin" <hpa@zytor.com> (arch/x86)
Cc: Arnd Bergmann <arnd@arndb.de> (include/asm-generic)
Cc: Rusty Russell <rusty@rustcorp.com.au> ("Hard To Misuse" list)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace inode_setattr with opencoded variants of it in all callers. This
moves the remaining call to vmtruncate into the filesystem methods where it
can be replaced with the proper truncate sequence.
In a few cases it was obvious that we would never end up calling vmtruncate
so it was left out in the opencoded variant:
spufs: explicitly checks for ATTR_SIZE earlier
btrfs,hugetlbfs,logfs,dlmfs: explicitly clears ATTR_SIZE earlier
ufs: contains an opencoded simple_seattr + truncate that sets the filesize just above
In addition to that ncpfs called inode_setattr with handcrafted iattrs,
which allowed to trim down the opencoded variant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Thomas Backlund reported that the powerpc build broke with make 3.82.
It failed with the following message:
arch/powerpc/Makefile:183: *** mixed implicit and normal rules. Stop.
The fix is to avoid mixing non-wildcard and wildcard targets.
Reported-by: Thomas Backlund <tmb@mandriva.org>
Tested-by: Thomas Backlund <tmb@mandriva.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Work around a silicon bug in the ac97 reset functionality of the
mpc5200(b). The implementation of the ac97 "cold" reset is flawed.
If the sync and output lines are high when reset is asserted the
attached ac97 device may go into test mode. Avoid this by
reconfiguring the psc to gpio mode and generating the reset manually.
From MPC5200B User's Manual:
"Some AC97 devices goes to a test mode, if the Sync line is high
during the Res line is low (reset phase). To avoid this behavior the
Sync line must be also forced to zero during the reset phase. To do
that, the pin muxing should switch to GPIO mode and the GPIO control
register should be used to control the output lines."
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xen: Do not suspend IPI IRQs.
powerpc: Use IRQF_NO_SUSPEND not IRQF_TIMER for non-timer interrupts
ixp4xx-beeper: Use IRQF_NO_SUSPEND not IRQF_TIMER for non-timer interrupt
irq: Add new IRQ flag IRQF_NO_SUSPEND
* 'timers-timekeeping-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
um: Fix read_persistent_clock fallout
kgdb: Do not access xtime directly
powerpc: Clean up obsolete code relating to decrementer and timebase
powerpc: Rework VDSO gettimeofday to prevent time going backwards
clocksource: Add __clocksource_updatefreq_hz/khz methods
x86: Convert common clocksources to use clocksource_register_hz/khz
timekeeping: Make xtime and wall_to_monotonic static
hrtimer: Cleanup direct access to wall_to_monotonic
um: Convert to use read_persistent_clock
timkeeping: Fix update_vsyscall to provide wall_to_monotonic offset
powerpc: Cleanup xtime usage
powerpc: Simplify update_vsyscall
time: Kill off CONFIG_GENERIC_TIME
time: Implement timespec_add
x86: Fix vtime/file timestamp inconsistencies
Trivial conflicts in Documentation/feature-removal-schedule.txt
Much less trivial conflicts in arch/powerpc/kernel/time.c resolved as
per Thomas' earlier merge commit 47916be4e2 ("Merge branch
'powerpc.cherry-picks' into timers/clocksource")
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (28 commits)
driver core: device_rename's new_name can be const
sysfs: Remove owner field from sysfs struct attribute
powerpc/pci: Remove owner field from attribute initialization in PCI bridge init
regulator: Remove owner field from attribute initialization in regulator core driver
leds: Remove owner field from attribute initialization in bd2802 driver
scsi: Remove owner field from attribute initialization in ARCMSR driver
scsi: Remove owner field from attribute initialization in LPFC driver
cgroupfs: create /sys/fs/cgroup to mount cgroupfs on
Driver core: Add BUS_NOTIFY_BIND_DRIVER
driver core: fix memory leak on one error path in bus_register()
debugfs: no longer needs to depend on SYSFS
sysfs: Fix one more signature discrepancy between sysfs implementation and docs.
sysfs: fix discrepancies between implementation and documentation
dcdbas: remove a redundant smi_data_buf_free in dcdbas_exit
dmi-id: fix a memory leak in dmi_id_init error path
sysfs: sysfs_chmod_file's attr can be const
firmware: Update hotplug script
Driver core: move platform device creation helpers to .init.text (if MODULE=n)
Driver core: reduce duplicated code for platform_device creation
Driver core: use kmemdup in platform_device_add_resources
...
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
sched: Use correct macro to display sched_child_runs_first in /proc/sched_debug
sched: No need for bootmem special cases
sched: Revert nohz_ratelimit() for now
sched: Reduce update_group_power() calls
sched: Update rq->clock for nohz balanced cpus
sched: Fix spelling of sibling
sched, cpuset: Drop __cpuexit from cpu hotplug callbacks
sched: Fix the racy usage of thread_group_cputimer() in fastpath_timer_check()
sched: run_posix_cpu_timers: Don't check ->exit_state, use lock_task_sighand()
sched: thread_group_cputime: Simplify, document the "alive" check
sched: Remove the obsolete exit_state/signal hacks
sched: task_tick_rt: Remove the obsolete ->signal != NULL check
sched: __sched_setscheduler: Read the RLIMIT_RTPRIO value lockless
sched: Fix comments to make them DocBook happy
sched: Fix fix_small_capacity
powerpc: Exclude arch_sd_sibiling_asym_packing() on UP
powerpc: Enable asymmetric SMT scheduling on POWER7
sched: Add asymmetric group packing option for sibling domain
sched: Fix capacity calculations for SMT4
sched: Change nohz idle load balancing logic to push model
...
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (162 commits)
tracing/kprobes: unregister_trace_probe needs to be called under mutex
perf: expose event__process function
perf events: Fix mmap offset determination
perf, powerpc: fsl_emb: Restore setting perf_sample_data.period
perf, powerpc: Convert the FSL driver to use local64_t
perf tools: Don't keep unreferenced maps when unmaps are detected
perf session: Invalidate last_match when removing threads from rb_tree
perf session: Free the ref_reloc_sym memory at the right place
x86,mmiotrace: Add support for tracing STOS instruction
perf, sched migration: Librarize task states and event headers helpers
perf, sched migration: Librarize the GUI class
perf, sched migration: Make the GUI class client agnostic
perf, sched migration: Make it vertically scrollable
perf, sched migration: Parameterize cpu height and spacing
perf, sched migration: Fix key bindings
perf, sched migration: Ignore unhandled task states
perf, sched migration: Handle ignored migrate out events
perf: New migration tool overview
tracing: Drop cpparg() macro
perf: Use tracepoint_synchronize_unregister() to flush any pending tracepoint call
...
Fix up trivial conflicts in Makefile and drivers/cpufreq/cpufreq.c
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
debug_core,kdb: fix crash when arch does not have single step
kgdb,x86: use macro HBP_NUM to replace magic number 4
kgdb,mips: remove unused kgdb_cpu_doing_single_step operations
mm,kdb,kgdb: Add a debug reference for the kdb kmap usage
KGDB: Remove set but unused newPC
ftrace,kdb: Allow dumping a specific cpu's buffer with ftdump
ftrace,kdb: Extend kdb to be able to dump the ftrace buffer
kgdb,powerpc: Replace hardcoded offset by BREAK_INSTR_SIZE
arm,kgdb: Add ability to trap into debugger on notify_die
gdbstub: do not directly use dbg_reg_def[] in gdb_cmd_reg_set()
gdbstub: Implement gdbserial 'p' and 'P' packets
kgdb,arm: Individual register get/set for arm
kgdb,mips: Individual register get/set for mips
kgdb,x86: Individual register get/set for x86
kgdb,kdb: individual register set and and get API
gdbstub: Optimize kgdb's "thread:" response for the gdb serial protocol
kgdb: remove custom hex_to_bin()implementation
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
modpost: support objects with more than 64k sections
trivial: fix a typo in a filename
frv: clean up arch/frv/Makefile
kbuild: allow assignment to {A,C}FLAGS_KERNEL on the command line
kbuild: allow assignment to {A,C,LD}FLAGS_MODULE on the command line
Kbuild: Add option to set -femit-struct-debug-baseonly
Makefile: "make kernelrelease" should show the correct full kernel version
Makefile.build: make KBUILD_SYMTYPES work again
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (79 commits)
powerpc/8xx: Add support for the MPC8xx based boards from TQC
powerpc/85xx: Introduce support for the Freescale P1022DS reference board
powerpc/85xx: Adding DTS for the STx GP3-SSA MPC8555 board
powerpc/85xx: Change deprecated binding for 85xx-based boards
powerpc/tqm85xx: add a quirk for ti1520 PCMCIA bridge
powerpc/tqm85xx: update PCI interrupt-map attribute
powerpc/mpc8308rdb: support for MPC8308RDB board from Freescale
powerpc/fsl_pci: add quirk for mpc8308 pcie bridge
powerpc/85xx: Cleanup QE initialization for MPC85xxMDS boards
powerpc/85xx: Fix booting for P1021MDS boards
powerpc/85xx: Fix SWIOTLB initalization for MPC85xxMDS boards
powerpc/85xx: kexec for SMP 85xx BookE systems
powerpc/5200/i2c: improve i2c bus error recovery
of/xilinxfb: update tft compatible versions
powerpc/fsl-diu-fb: Support setting display mode using EDID
powerpc/5121: doc/dts-bindings: update doc of FSL DIU bindings
powerpc/5121: shared DIU framebuffer support
powerpc/5121: move fsl-diu-fb.h to include/linux
powerpc/5121: fsl-diu-fb: fix issue with re-enabling DIU area descriptor
powerpc/512x: add clock structure for Video-IN (VIU) unit
...
kgdb_handle_breakpoint checks the first arch_kgdb_breakpoint
which is not known by gdb that's why is necessary jump over
it. The jump lenght is equal to BREAK_INSTR_SIZE that's
why is cleaner to use defined macro instead of hardcoded
non-described offset.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Right now, both the "memory" and "reserved" memblock_type structures have
a "size" member. It represents the calculated memory size in the former
case and is unused in the latter.
This moves it out to the main memblock structure instead
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The RMA (RMO is a misnomer) is a concept specific to ppc64 (in fact
server ppc64 though I hijack it on embedded ppc64 for similar purposes)
and represents the area of memory that can be accessed in real mode
(aka with MMU off), or on embedded, from the exception vectors (which
is bolted in the TLB) which pretty much boils down to the same thing.
We take that out of the generic MEMBLOCK data structure and move it into
arch/powerpc where it belongs, renaming it to "RMA" while at it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This introduce memblock.current_limit which is used to limit allocations
from memblock_alloc() or memblock_alloc_base(..., MEMBLOCK_ALLOC_ACCESSIBLE).
The old MEMBLOCK_ALLOC_ANYWHERE changes value from 0 to ~(u64)0 and can still
be used with memblock_alloc_base() to allocate really anywhere.
It is -no-longer- cropped to MEMBLOCK_REAL_LIMIT which disappears.
Note to archs: I'm leaving the default limit to MEMBLOCK_ALLOC_ANYWHERE. I
strongly recommend that you ensure that you set an appropriate limit
during boot in order to guarantee that an memblock_alloc() at any time
results in something that is accessible with a simple __va().
The reason is that a subsequent patch will introduce the ability for
the array to resize itself by reallocating itself. The MEMBLOCK core will
honor the current limit when performing those allocations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Introduce basic support for the Freescale P1022DS reference board, based on the
Freescale BSP for this board. This patch excludes the DIU, SSI, and MMC/SD
drivers. Only a 36-bit DTS is provided.
Update mpc86xx_smp_defconfig and mpc85xx_defconfig to support the P1022DS.
This means enabling 64-bit physical address support, increasing the maximum
zone order to 12 (to allow the DIU driver to allocate large chunks), and
clean up the audio options to disable the deprecated OSS support.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This version uses "fsl,mpc8555..." instead of "fsl,85..." notation.
There is also an 8541 version of this board so DTS for this board
is specific to the 8555 processor.
Another patch is coming to fix-up other DTS that use old notation.
Signed-off-by: Bradley Hughes <bhughes@silicontkx.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The "fsl,85..." style compatible binding was to be deprecated
some time ago. This patch corrects existing occurrences of
the incorrect binding. The memory-controller and
l2-cache-controller are the only affected nodes.
Signed-off-by: Bradley Hughes <bhughes@silicontkx.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By default ti1520 bridge expects an input clock on CLOCK pin (to control
power chip). However on this boards CLOCK should be generated by PCI1520
itself. Add a quirk that enables internal 16 KHz clock generation on
this pin.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update PCI IRQ mapping on TQM85xx platforms: include INTC and INTD on PCI-X
slot and add INTA/INTB mapping for PCMCIA bridge.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for MPC8308RDB development board from
Freescale.
Supported devices:
DUART
Dual Ethernet
NOR and NAND flashes
I2C
USB in peripheral mode
PCIE support is broken by the commit 3da34aa ("powerpc/fsl: Support
unique MSI addresses per PCIe Root Complex"). Works after revert.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the quirk for PCIE controller found on Freescale MPC8308.
The quirk is the same as for other MPC83xx processors.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc85xx_mds_setup_arch() function is incomprehensible
and unmaintainable. Factor out all QE specific stuff into
mpc85xx_mds_qe_init() and mpc85xx_mds_reset_ucc_phys().
Also move QE stuff out of mpc85xx_mds_pic_init().
The diff is unreadable, but only because the code was so. ;-)
It should be better now, and less indented.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021 processors have no dedicated ROM to store the QE microcode,
so the fimrware is stored externally, and it is U-Boot responsibility
to load it. It might be that the board is booting without QE, e.g.
currently U-Boot doesn't support QE for P1021MDS boards, which means
that QE isn't initialized, and so the board hangs early at boot.
This patch fixes the issue by marking QE as disabled and checking the
state in the probing code. U-Boot should fixup the state if it
initialized the QE.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code inside '#ifdef CONFIG_QUICC_ENGINE' makes the
mpc85xx_mds_setup_arch() return early if no QE nodes present,
and so SWIOTLB is never initialized.
This patch fixes the issue by moving SWIOTLB code above
QE.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
It is now possible to assign options to AS, CC and LD
on the command line - which is only used when building modules.
{A,C,LD}FLAGS_MODULE was all used both in the top-level Makefile
in the arch makefiles, thus users had no way to specify
additional options to AS, CC, LD when building modules
without overriding the original value.
Introduce a new set of variables KBUILD_{A,C,LD}FLAGS_MODULE
that is used by arch specific files and free up
{A,C,LD}FLAGS_MODULE so they can be assigned on
the command line.
All arch Makefiles that used the old variables has been updated.
Note: Previously we had a MODFLAGS variable for both
AS and CC. But in favour of consistency this was dropped.
So in some cases arch Makefile has one assignmnet replaced by
two assignmnets.
Note2: MODFLAGS was not documented and is dropped
without any notice. I do not expect much/any breakage
from this.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Acked-by: Mike Frysinger <vapier@gentoo.org> [blackfin]
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [avr32]
Signed-off-by: Michal Marek <mmarek@suse.cz>
Commit 6b95ed345b changed from
a struct initializer to perf_sample_data_init(), but the setting
of the .period member was left out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mackerras <paulus@samba.org>
For some reason the FSL driver got left out when we converted perf
to use local64_t instead of atomic64_t.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds support for kexec on 85xx machines for the BookE platform.
Including support for SMP machines
Based off work from Maxim Uvarov <muvarov@mvista.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For 32bit machines where the physical address width is
larger than the virtual address width the frame number types
in KVM may overflow. Fix this by changing them to u64.
[sfr: fix build on 32-bit ppc]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
MPC5121 DIU configuration/setup as initialized by the boot
loader currently will get lost while booting Linux. As a
result displaying the boot splash is not possible through
the boot process.
To prevent this we reserve configured DIU frame buffer
address range while booting and preserve AOI descriptor
and gamma table so that DIU continues displaying through
the whole boot process. On first open from user space
DIU frame buffer driver releases the reserved frame
buffer area and continues to operate as usual.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allows using clk_get()/clk_enable()/clk_disable() for VIU
clock in the v4l2 video driver.
Signed-off-by: Hongjun Chen <hong-jun.chen@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow board selection in a drop-down board sub-menu
like many other platforms do.
Before the patch:
...
[ ] Freescale MPC5121E ADS
[ ] Generic support for simple MPC5121 based boards
[ ] 52xx-based boards
...
Patched:
...
[*] 512x-based boards
[ ] Freescale MPC5121E ADS
[ ] Generic support for simple MPC5121 based boards
[ ] 52xx-based boards
...
This is a cleanup before adding new board selection entry.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts unnecessary divide and modulo operations
in the KVM large page related code into logical operations.
This allows to convert gfn_t to u64 while not breaking 32
bit builds.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We just introduced generic functions to handle shadow pages on PPC.
This patch makes the respective backends make use of them, getting
rid of a lot of duplicate code along the way.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Currently the shadow paging code keeps an array of entries it knows about.
Whenever the guest invalidates an entry, we loop through that entry,
trying to invalidate matching parts.
While this is a really simple implementation, it is probably the most
ineffective one possible. So instead, let's keep an array of lists around
that are indexed by a hash. This way each PTE can be added by 4 list_add,
removed by 4 list_del invocations and the search only needs to loop through
entries that share the same hash.
This patch implements said lookup and exports generic functions that both
the 32-bit and 64-bit backend can use.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
When a guest sets its SR entry to invalid, we may still find a
corresponding entry in a BAT. So we need to make sure we're not
faulting on invalid SR entries, but instead just claim them to be
BAT resolved.
This resolves breakage experienced when using libogc based guests.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The linux kernel already provides a hash function. Let's reuse that
instead of reinventing the wheel!
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Initially we had to search for pte entries to invalidate them. Since
the logic has improved since then, we can just get rid of the search
function.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
As advertised in feature-removal-schedule.txt. Equivalent support is provided
by overlapping memory regions.
Signed-off-by: Avi Kivity <avi@redhat.com>
Fixes:
arch/powerpc/kvm/booke.c: In function 'kvmppc_core_deliver_interrupts':
arch/powerpc/kvm/booke.c:147: warning: 'msr_mask' may be used uninitialized in this function
Signed-off-by: Asias He <asias.hejun@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix compile warning:
CC [M] arch/powerpc/kvm/powerpc.o
arch/powerpc/kvm/powerpc.c: In function 'kvm_arch_vcpu_ioctl_run':
arch/powerpc/kvm/powerpc.c:290: warning: 'gpr' may be used uninitialized in this function
arch/powerpc/kvm/powerpc.c:290: note: 'gpr' was declared here
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch moves the declaration of of_get_address(), of_get_pci_address(),
and of_pci_address_to_resource() out of arch code and into the common
linux/of_address header file.
This patch also fixes some of the asm/prom.h ordering issues. It still
includes some header files that it ideally shouldn't be, but at least the
ordering is consistent now so that of_* overrides work.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Instead of instantiating a whole thread_struct on the stack use only the
required parts of it.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Now that all arch specific ioctls have centralized locking, it is easy to
move it to the central dispatcher.
Signed-off-by: Avi Kivity <avi@redhat.com>
All vcpu ioctls need to be locked, so instead of locking each one specifically
we lock at the generic dispatcher.
This patch only updates generic ioctls and leaves arch specific ioctls alone.
Signed-off-by: Avi Kivity <avi@redhat.com>
When CPU hotplug is used, some CPUs may be offline at the time a kexec is
performed. The subsequent kernel may expect these CPUs to be already running,
and will declare them stuck. On pseries, there's also a soft-offline (cede)
state that CPUs may be in; this can also cause problems as the kexeced kernel
may ask RTAS if they're online -- and RTAS would say they are. The CPU will
either appear stuck, or will cause a crash as we replace its cede loop beneath
it.
This patch kicks each present offline CPU awake before the kexec, so that
none are forever lost to these assumptions in the subsequent kernel.
Now, the behaviour is that all available CPUs that were offlined are now
online & usable after the kexec. This mimics the behaviour of a full reboot
(on which all CPUs will be restarted).
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tidies some typos, KERN_INFO-ise an info msg, and add a debug msg showing
when the final sequence starts.
Also adds a comment to kexec_prepare_cpus_wait() to make note of a possible
problem; the need for kexec to deal with CPUs that failed to originally start
up.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we look pretty stupid when printing out a bunch of things in
prom_init.c. eg.
Max number of cores passed to firmware: 0x0000000000000080
So I've change this to print in decimal:
Max number of cores passed to firmware: 128 (NR_CPUS = 256)
This required adding a prom_print_dec() function and changing some
prom_printk() calls from %x to %lu.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a CPU remove is attempted using the 'release' interface on hardware
which supports extended cede, the CPU will be put in the INACTIVE state
rather than the OFFLINE state due to the default preferred_offline_state
in that situation. In the INACTIVE state it will fail to be removed.
This patch changes the preferred offline state to OFFLINE when an CPU is
in the ONLINE state. After cpu_down() is called in dlpar_offline_cpu()
the CPU will be OFFLINE and CPU removal can continue.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds support for the Mac Mini's that were quietly rolled out
in 2005. Work still needs to be done to support suspend and
WakeOnLan.
Signed-off-by: Mark Crichton <crichton@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In testing SMT disable, we have been regularly seeing the following
message:
Querying DEAD? cpu %i (%i) shows %i
This indicates the current delay in pseries_cpu_die where we wait
for the specified CPU to die, is insufficient. Usually, this does
not cause a problem, but we've seen this result in BUG_ON's going
off in the timer code when we try to migrate the timers off the
dead cpu while a timer is still running. Increasing this delay,
as is done in this patch, seems to resolve this issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We already defined start_cpu_decrementer() to invoke decrementer for AP as
the following path:
start_secondary() -> secondary_cpu_time_init() -> start_cpu_decrementer()
So remove these incorrect codes introduced from commit:
e7f75ad0 powerpc/47x: Base ppc476 support
And actually we really should not enable decrementer before calling set_dec().
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerPC we should always use generic ISA DMA API implementation
as there is simply no other implementation exist.
Without this patch, the following build error pops up:
sound/built-in.o: In function 'snd_dma_pointer':
(.text+0x74ae): undefined reference to 'dma_spin_lock'
...
make: *** [.tmp_vmlinux1] Error 1
This is PPC_85xx, SMP and some sound drivers set to =y.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While testing cpu offlining, we are regularly seeing the WARN_ON go off
in xics_ipi_dispatch. It can occur when an IPI gets sent to the CPU while
it is going offline. There is already a similar WARN_ON in the handlers
for PPC_MSG_CALL_FUNCTION and PPC_MSG_CALL_FUNC_SINGLE, so the warning
is not needed in that path. The debugger handler handles this case by
simply ignoring IPIs for offline CPUs, so no warning is needed there.
And the reschedule IPI, which is what is occurring in our test environment,
can be safely ignored, so we can simply remove the WARN_ON from xics_ipi_dispatch.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix sizes of variables so correct values are exported via /proc.
Cast variable in comparison to avoid compiler error.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With dynamic PACAs, the kexecing CPU's PACA won't lie within the kernel
static data and there is a chance that something may stomp it when preparing
to kexec. This patch switches this final CPU to a static PACA just before
we pull the switch.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
of_node_to_nid() is only relevant in a few architectures. Don't force
everyone to implement it anyway.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
kw_i2c_irq and via_pmu_interrupt are not timer interrupts and
therefore should not use IRQF_TIMER. Use the recently introduced
IRQF_NO_SUSPEND instead since that is the actual desired behaviour.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linuxppc-dev@ozlabs.org
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1280398595-29708-3-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Conflicts:
arch/powerpc/kernel/time.c
Reason: The powerpc next tree contains two commits which conflict with
the timekeeping changes:
8fd63a9e powerpc: Rework VDSO gettimeofday to prevent time going backwards
c1aa687d powerpc: Clean up obsolete code relating to decrementer and timebase
John Stultz identified them and provided the conflict resolution.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the decrementer and timekeeping code was moved over to using
the generic clockevents and timekeeping infrastructure, several
variables and functions have been obsolete and effectively unused.
This deletes them.
In particular, wakeup_decrementer() is no longer needed since the
generic code reprograms the decrementer as part of the process of
resuming the timekeeping code, which happens during sysdev resume.
Thus the wakeup_decrementer calls in the suspend_enter methods for
52xx platforms have been removed. The call in the powermac cpu
frequency change code has been replaced by set_dec(1), which will
cause a timer interrupt as soon as interrupts are enabled, and the
generic code will then reprogram the decrementer with the correct
value.
This also simplifies the generic_suspend_en/disable_irqs functions
and makes them static since they are not referenced outside time.c.
The preempt_enable/disable calls are removed because the generic
code has disabled all but the boot cpu at the point where these
functions are called, so we can't be moved to another cpu.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently it is possible for userspace to see the result of
gettimeofday() going backwards by 1 microsecond, assuming that
userspace is using the gettimeofday() in the VDSO. The VDSO
gettimeofday() algorithm computes the time in "xsecs", which are
units of 2^-20 seconds, or approximately 0.954 microseconds,
using the algorithm
now = (timebase - tb_orig_stamp) * tb_to_xs + stamp_xsec
and then converts the time in xsecs to seconds and microseconds.
The kernel updates the tb_orig_stamp and stamp_xsec values every
tick in update_vsyscall(). If the length of the tick is not an
integer number of xsecs, then some precision is lost in converting
the current time to xsecs. For example, with CONFIG_HZ=1000, the
tick is 1ms long, which is 1048.576 xsecs. That means that
stamp_xsec will advance by either 1048 or 1049 on each tick.
With the right conditions, it is possible for userspace to get
(timebase - tb_orig_stamp) * tb_to_xs being 1049 if the kernel is
slightly late in updating the vdso_datapage, and then for stamp_xsec
to advance by 1048 when the kernel does update it, and for userspace
to then see (timebase - tb_orig_stamp) * tb_to_xs being zero due to
integer truncation. The result is that time appears to go backwards
by 1 microsecond.
To fix this we change the VDSO gettimeofday to use a new field in the
VDSO datapage which stores the nanoseconds part of the time as a
fractional number of seconds in a 0.32 binary fraction format.
(Or put another way, as a 32-bit number in units of 0.23283 ns.)
This is convenient because we can use the mulhwu instruction to
convert it to either microseconds or nanoseconds.
Since it turns out that computing the time of day using this new field
is simpler than either using stamp_xsec (as gettimeofday does) or
stamp_xtime.tv_nsec (as clock_gettime does), this converts both
gettimeofday and clock_gettime to use the new field. The existing
__do_get_tspec function is converted to use the new field and take
a parameter in r7 that indicates the desired resolution, 1,000,000
for microseconds or 1,000,000,000 for nanoseconds. The __do_get_xsec
function is then unused and is deleted.
The new algorithm is
now = ((timebase - tb_orig_stamp) << 12) * tb_to_xs
+ (stamp_xtime_seconds << 32) + stamp_sec_fraction
with 'now' in units of 2^-32 seconds. That is then converted to
seconds and either microseconds or nanoseconds with
seconds = now >> 32
partseconds = ((now & 0xffffffff) * resolution) >> 32
The 32-bit VDSO code also makes a further simplification: it ignores
the bottom 32 bits of the tb_to_xs value, which is a 0.64 format binary
fraction. Doing so gets rid of 4 multiply instructions. Assuming
a timebase frequency of 1GHz or less and an update interval of no
more than 10ms, the upper 32 bits of tb_to_xs will be at least
4503599, so the error from ignoring the low 32 bits will be at most
2.2ns, which is more than an order of magnitude less than the time
taken to do gettimeofday or clock_gettime on our fastest processors,
so there is no possibility of seeing inconsistent values due to this.
This also moves update_gtod() down next to its only caller, and makes
update_vsyscall use the time passed in via the wall_time argument rather
than accessing xtime directly. At present, wall_time always points to
xtime, but that could change in future.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should use perf_sample_data_init() to initialize struct
perf_sample_data. As explained in the description of commit dc1d628a
("perf: Provide generic perf_sample_data initialization"), it is
possible for userspace to get the kernel to dereference data.raw,
so if it is not initialized, that means that unprivileged userspace
can possibly oops the kernel. Using perf_sample_data_init makes sure
it gets initialized to NULL.
This conversion should have been included in commit dc1d628a, but it
got missed.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
update_vsyscall() did not provide the wall_to_monotoinc offset,
so arch specific implementations tend to reference wall_to_monotonic
directly. This limits future cleanups in the timekeeping core, so
this patch fixes the update_vsyscall interface to provide
wall_to_monotonic, allowing wall_to_monotonic to be made static
as planned in Documentation/feature-removal-schedule.txt
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tony Luck <tony.luck@intel.com>
LKML-Reference: <1279068988-21864-7-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This removes powerpc's direct xtime usage, allowing for further
generic timeekeping cleanups
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
LKML-Reference: <1279068988-21864-6-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently powerpc's update_vsyscall calls an inline update_gtod.
However, both are straightforward, and there are no other users,
so this patch merges update_gtod into update_vsyscall.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1279068988-21864-5-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-4-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The recent AMCC 405EX Rev D without Security uses a PVR value
that matches the old 405EXr Rev A/B with Security.
The 405EX Rev D without Security would be shown
incorrectly as an 405EXr. The pvr_mask of 0xffff0004
is no longer sufficient to distinguish the 405EX from 405EXr.
This patch replaces 2 entries in the cpu_specs table
and adds 8 more, each using pvr_mask of 0xffff000f
and appropriate pvr_value to distinguish the AMCC
PowerPC 405EX and 405EXr instances.
The cpu_name for these entries now includes the
Rev, in similar fashion to the 440GX.
Signed-off-by: Lee Nipper <lee.nipper@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
UART2 and UART3 on 460EX/GT have incorrect interrupt mappings right now.
UART2 should be 28 (0x1c) and UART3 29 (0x1d). This patch fixes this and
switches to using decimal number instead of hex, since the AppliedMicro
(AMCC) users manuals describe their inerrupt numbers in decimal.
Thanks to Fabien Proriol for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabien Proriol <Fabien.Proriol@jdsu.com>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The config options for REDWOOD_[456] were commented out in the powerpc
Kconfig. The ifdefs referencing this options therefore are dead and all
references to this can be removed (Also dependencies in other KConfig
files).
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This list used was by only two platforms with all other platforms defining an
own list of valid bus id's to pass to of_platform_bus_probe. This patch:
i) copies the default list to the two platforms that depended on it (powerpc)
ii) remove the usage of of_default_bus_ids in of_platform_bus_probe
iii) removes the definition of the list from all architectures that defined it
Passing a NULL 'matches' parameter to of_platform_bus_probe is still valid; the
function returns no error in that case as the NULL value is equivalent to an
empty list.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
[grant.likely@secretlab.ca: added __initdata annotations, warn on and return error on missing match table, and fix whitespace errors]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There's no need for this function to be architecture specific and all four
architectures defining it had the same definition. The function has been
moved to drivers/of/platform.c.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
[grant.likely@secretlab.ca: moved to drivers/of/platform.c, simplified code, and added kerneldoc comment]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
of_device is just a #define alias to platform_device. This patch
replaces all references to it with platform_device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
