This updates the CLPS711X defconfig to the thing saved by savedefconfig.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CLPS711X CPUs have 128 bytes of on-chip Boot ROM with an
instruction sequence that configure UART1 to receive up to
2 Kbytes of serial data which is then placed in the on-chip
SRAM. Once the download is complete, the program counter
jumps to SRAM to begin executed the downloaded data.
The purpose of this mode is to allow the downloaded code to
facilitate programming of FLASH or other ROM device. Selection
of the internal Boot ROM is accomplished at power-on-reset time.
No reason to keep this special (develop only) mode in the kernel.
This patch removes EP72XX_ROM_BOOT kernel symbol.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
of individual platforms as they are redundant.
- Make SMP, CACHE_L2X0 and GPIO config options user visible on
multi-platform builds as most platforms enable these options and all
platforms can run with them enabled.
- Make multi-platform v6 default to more optimal v6k rather than v6
- Remove the last bit of mach-virt and convert it to just a kconfig
option.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTBT1nAAoJEMhvYp4jgsXikI0IAIv2GmBCgbg0XhHZBSheSNOh
Th1bv4KeEci/3uezwVTAA3AtJIvDNMAQjRYjNSyOnCCC7s5czex1w/Mk/6IzgX8C
eCauM5kiOV3ZKPMbPI6gxg0bmFe+YzWREbm7fpAqxpc3IXwzYlShnq/kKISq25Qj
mRZtv97AB2xqAy9zTyy18y+c+F/1mAgd+NeiDbjBimHbTK4urjiD7PpcWvmbYZld
H9Qw4d9JwVTRpRHw9PRR9glnvFYiFpp+s9ehSjcyYi8wjZKO1+67c56fS+ScsoV7
qM4J2qtS2kpzvyFvOI7wY6E2M5Es7zOeuJAmh0jEkbDtRa0a4YFYL0DAp5k9Xiw=
=NEez
-----END PGP SIGNATURE-----
Merge tag 'kconfig-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next/cleanup
Merge "kconfig clean-up and mach-virt removal for 3.15" from Rob Herring
- Remove common kconfig options required by multi-platform builds out
of individual platforms as they are redundant.
- Make SMP, CACHE_L2X0 and GPIO config options user visible on
multi-platform builds as most platforms enable these options and all
platforms can run with them enabled.
- Make multi-platform v6 default to more optimal v6k rather than v6
- Remove the last bit of mach-virt and convert it to just a kconfig
option.
* tag 'kconfig-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ARM: virt: select ARM_AMBA
ARM: virt: make mach-virt just a kconfig option
ARM: vt8500: enable V6K instead of plain V6
ARM: cns3xxx: enable V6K instead of plain V6
ARM: bcm2835: enable V6K instead of plain V6
ARM: Select V6K instead of V6 by default for multi-platform
ARM: select MIGHT_HAVE_CACHE_L2X0 for V6 and V7 multi-platform
ARM: select HAVE_SMP for V7 multi-platform
ARM: centralize common multi-platform kconfig options
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
superflous select by ARCH_EFM32.
As these cleanups have dependencies on both v3.14-rc1 and my timex.h cleanup
(which is based on v3.13-rc1) this pull request also included a merge of my
cleanup tag which is already in armsoc/next/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=FW7m
-----END PGP SIGNATURE-----
Merge tag 'efm32-next' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
Merge "efm32 cleanups for next" from Uwe Kleine-König
Just three simple cleanups for efm32 removing two now unused files and a
superflous select by ARCH_EFM32.
As these cleanups have dependencies on both v3.14-rc1 and my timex.h cleanup
(which is based on v3.13-rc1) this pull request also included a merge of my
cleanup tag which is already in armsoc/next/cleanup.
* tag 'efm32-next' of git://git.pengutronix.de/git/ukl/linux:
ARM: efm32: drop unused file <mach/timex.h>
ARM: efm32: drop selecting CLKSRC_MMIO
ARM: efm32: drop unused file entry-macro.S
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This file is unused since commit
79f08d9ed2 (ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too)
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-mmp/time.c
arch/arm/mach-sa1100/time.c
CLKSRC_MMIO is needed on efm32 because the clocksource driver
(CLKSRC_EFM32) uses clocksource_mmio_init() and
clocksource_mmio_readl_up(). Since commit 09ca27579e (clocksource:
time-efm32: Select CLKSRC_MMIO) CLKSRC_EFM32 does the necessary select
itself and ARCH_EFM32 doesn't need to select it explicitly any more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This file is unused since commit
e6d159cdf9 (ARM: 7890/1: v7-M: drop using mach/entry-macro.S)
which went into v3.14-rc1.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- mvebu
- Makefile cleanup and remove map_io
- use of_find_matching_node_and_match
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=xrGQ
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-3.15' of git://git.infradead.org/linux-mvebu into next/cleanup
Merge "mvebu soc changes for v3.15" from Jason Cooper:
- mvebu
- Makefile cleanup and remove map_io
- use of_find_matching_node_and_match
* tag 'mvebu-soc-3.15' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: remove unneeded ->map_io field for Armada 370/XP
ARM: mvebu: make use of of_find_matching_node_and_match
ARM: mvebu: Makefile clean-up
Signed-off-by: Olof Johansson <olof@lixom.net>
Split of the multiplatform support for the Qualcomm SoCs into a mach-qcom
while we leave mach-msm as legacy support. Also, some smp and device tree
related cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
Comment: GPGTools - https://gpgtools.org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=hwTa
-----END PGP SIGNATURE-----
Merge tag 'qcom-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/cleanup
Merge "General cleanups for MSM/QCOM for 3.15" from Kumar Gala:
Split of the multiplatform support for the Qualcomm SoCs into a mach-qcom
while we leave mach-msm as legacy support. Also, some smp and device tree
related cleanups.
* tag 'qcom-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: qcom: Rename various msm prefixed functions to qcom
clocksource: qcom: split building of legacy vs multiplatform support
ARM: qcom: Split Qualcomm support into legacy and multiplatform
clocksource: qcom: Move clocksource code out of mach-msm
ARM: msm: kill off hotplug.c
ARM: msm: Remove pen_release usage
ARM: dts: msm: split out msm8660 and msm8960 soc into dts include
Signed-off-by: Olof Johansson <olof@lixom.net>
Guests can use AMBA bus devices such as the PL011 uart, so enable the
AMBA bus for mach-virt.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
The mach code for mach-virt is no longer needed, so we can remove all of
mach-virt except the kconfig entry.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
The wm8750 is an ARM1176 which has all the V6K extensions except for SMP,
so V6K should be selected instead. Dropping the select will use the
default for ARCH_MULTI_V6 which is V6K.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
The cns3xxx is an ARM11MPCore which has all the V6K extensions, so V6K
should be selected instead. Dropping the select will use the default for
ARCH_MULTI_V6 which is V6K.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Anton Vorontsov <anton@enomsg.org>
The bcm2835 is an ARM1176 which has all the V6K extensions except for SMP,
so V6K should be selected instead. Dropping the select will use
the default for ARCH_MULTI_V6 which is V6K.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
MULTI_V6 should default to V6K as it is more optimal than V6. Any
platform which is not V6K should select CPU_V6 which will enable the
less optimal code paths.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Many V6 and V7 platforms have an L2x0 cache, so make
CONFIG_MIGHT_HAVE_CACHE_L2X0 visible for V6 and V7 multi-platform
builds.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
All V7 platforms can run SMP kernels, so make CONFIG_SMP visible for V7
multi-platform builds.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Multi-platform requires various kconfig options to be selected, so
platforms don't need to select them individually.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
In commit f0402f9b47 ("ARM: ixp4xx: stop using <mach/timex.h>")
I didn't intend to implement a functional change, but as Olof noticed I
failed---at least a bit. Before this commit the following was used to
determine the latch value used:
#define IXP4XX_TIMER_FREQ 66666000
#define CLOCK_TICK_RATE \
(((IXP4XX_TIMER_FREQ / HZ & ~IXP4XX_OST_RELOAD_MASK) + 1) * HZ)
#define LATCH ((CLOCK_TICK_RATE + HZ/2) / HZ)
The complicated calculation was done "b/c the timer register ignores the
bottom 2 bits of the LATCH value." With HZ=100 CLOCK_TICK_RATE used to
calculate to 66666100 and so LATCH to 666661. In ixp4xx_set_mode the
term
LATCH & ~IXP4XX_OST_RELOAD_MASK
was used to write to the relevant register (with IXP4XX_OST_RELOAD_MASK
being 3) and so effectively 666660 was used.
In commit f0402f9b47 I translated that to:
#define IXP4XX_TIMER_FREQ 66666000
#define IXP4XX_LATCH DIV_ROUND_CLOSEST(IXP4XX_TIMER_FREQ, HZ)
which results in the same register writes, but still doesn't bear in
mind that the two least significant bits cannot be specified (which is
relevant only when HZ or IXP4XX_TIMER_FREQ are changed).
Instead of reverting back to the old approach use a more obvious and
also more correct way to calculate LATCH. (Regarding the more
correct claim: With IXP4XX_TIMER_FREQ == 66665999, the old code resulted
in LATCH = 666657 corresponding to a cycle time of 0.009999940149400597
seconds (error: -6.0e-8 s) while the new approach results in LATCH =
666660 and so a cycle time of 0.010000000150001503 seconds
(error: 1.5e-10 s).)
Fixes: f0402f9b47 ("ARM: ixp4xx: stop using <mach/timex.h>")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Pull btrfs fixes from Chris Mason:
"We have a small collection of fixes in my for-linus branch.
The big thing that stands out is a revert of a new ioctl. Users
haven't shipped yet in btrfs-progs, and Dave Sterba found a better way
to export the information"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: use right clone root offset for compressed extents
btrfs: fix null pointer deference at btrfs_sysfs_add_one+0x105
Btrfs: unset DCACHE_DISCONNECTED when mounting default subvol
Btrfs: fix max_inline mount option
Btrfs: fix a lockdep warning when cleaning up aborted transaction
Revert "btrfs: add ioctl to export size of global metadata reservation"
- Fix booting on PPC boards. Changes to of_match_node matching caused
the serial port on some PPC boards to stop working. Reverted the
change and reimplement to split matching between new style compatible
only matching and fallback to old matching algorithm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTABFuAAoJEMhvYp4jgsXi2PkH/1F9qpuZ1MAHCqu5scBbozKt
LST0Q2qfspl+PjEN30D2X4S6O0qhHeEjeC96AfNUqpJ6sDLws/XcTlfG3niszebi
ldJHnLp4lOJHBby0XtYjyQTyfBnJUYzTfau6DfqpjhZa0ljUHCrbPjvjrp+mqblL
LNmwlK3dzc9dTo925v3R6R+v6Zn5o2Fe9SrQIdNSBCVbJYLDIRK6qhRrI1fJaBwn
rNjf6Bwlt5XJFR8hw9MYUmUQH6bBIhhQGbDKJwnGPaqTDCMXUcRj9KC0HEpOAiJU
h2xROVs8dlnBSyKq/QTlVP2b8AHPNHt4p4HkmIuJFkEJHrnv0iy86ssKROt2dO4=
=j9kb
-----END PGP SIGNATURE-----
Merge tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
"Fix booting on PPC boards. Changes to of_match_node matching caused
the serial port on some PPC boards to stop working. Reverted the
change and reimplement to split matching between new style compatible
only matching and fallback to old matching algorithm"
* tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: search the best compatible match first in __of_match_node()
Revert "OF: base: match each node compatible against all given matches first"
Currently, of_match_node compares each given match against all node's
compatible strings with of_device_is_compatible.
To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and also
an alphabetical ordering is more sane there.
Therefore, this patch introduces a function to match each of the node's
compatible strings against all given compatible matches without type and
name first, before checking the next compatible string. This implies
that node's compatibles are ordered from specific to generic while
given matches can be in any order. If we fail to find such a match
entry, then fall-back to the old method in order to keep compatibility.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time to v3.14-rc1 related changes. Also
included is one fix for a free after use regression in persistent
reservations UNREGISTER logic that is CC'ed to >= v3.11.y stable"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix protection copy routine
IB/srpt: replace strict_strtoul() with kstrtoul()
target: Simplify command completion by removing CMD_T_FAILED flag
iser-target: Fix leak on failure in isert_conn_create_fastreg_pool
iscsi-target: Fix SNACK Type 1 + BegRun=0 handling
target: Fix missing length check in spc_emulate_evpd_83()
qla2xxx: Remove last vestiges of qla_tgt_cmd.cmd_list
target: Fix 32-bit + CONFIG_LBDAF=n link error w/ sector_div
target: Fix free-after-use regression in PR unregister
Pull i2c fixes from Wolfram Sang:
"i2c has a bugfix and documentation improvements for you"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Documentation: i2c: mention ACPI method for instantiating devices
Documentation: i2c: describe devicetree method for instantiating devices
i2c: mv64xxx: refactor message start to ensure proper initialization
Pull irq update from Thomas Gleixner:
"Fix from the urgent branch: a trivial oneliner adding the missing
Kconfig dependency curing build failures which have been discovered by
several build robots.
The update in the irq-core branch provides a new function in the
irq/devres code, which is a prerequisite for driver developers to get
rid of boilerplate code all over the place.
Not a bugfix, but it has zero impact on the current kernel due to the
lack of users. It's simpler to provide the infrastructure to
interested parties via your tree than fulfilling the wishlist of
driver maintainers on which particular commit or tag this should be
based on"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add missing irq_to_desc export for CONFIG_SPARSE_IRQ=n
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add devm_request_any_context_irq()
Pull timer fixes from Thomas Gleixner:
"The following trilogy of patches brings you:
- fix for a long standing math overflow issue with HZ < 60
- an onliner fix for a corner case in the dreaded tick broadcast
mechanism affecting a certain range of AMD machines which are
infested with the infamous automagic C1E power control misfeature
- a fix for one of the ARM platforms which allows the kernel to
proceed and boot instead of stupidly panicing for no good reason.
The patch is slightly larger than necessary, but it's less ugly
than the alternative 5 liner"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Clear broadcast pending bit when switching to oneshot
clocksource: Kona: Print warning rather than panic
time: Fix overflow when HZ is smaller than 60
The first is a fix for the way the ring buffer stores timestamps.
After a restructure of the code was done, the ring buffer timestamp
logic missed the fact that the first event on a sub buffer is to have
a zero delta, as the full timestamp is stored on the sub buffer itself.
But because the delta was not cleared to zero, the timestamp for that
event will be calculated as the real timestamp + the delta from the
last timestamp. This can skew the timestamps of the events and
have them say they happened when they didn't really happen. That's bad.
The second fix is for modifying the function graph caller site.
When the stop machine was removed from updating the function tracing
code, it missed updating the function graph call site location.
It is still modified as if it is being done via stop machine. But it's not.
This can lead to a GPF and kernel crash if the function graph call site
happens to lie between cache lines and one CPU is executing it while
another CPU is doing the update. It would be a very hard condition to
hit, but the result is sever enough to have it fixed ASAP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJS/2leAAoJEKQekfcNnQGu7nYH/AltUO19AgM2sFLOLM7Q0dp4
Lg7vE8CLKtFq0fjtv/ri//fJ56Lr+/WNHiiD06aIrgnMVBbWynS0m0RO+9bhFl8/
rELiUpXTTruqljmlT2T5lPxk+ZKgtLbxK8hNywU99eLgkTwyaOwrSUol30E8pw41
UwtKg4OAn1LbjQ8/sddVynGlFDNRdqFiGTIDvhHqI6F6/QlaEX81EeZbLThDU4D/
l86fMuIdw5pb+efa29Rr0s7O4Xol7SJgnSMVgd0OYADRFmp4sg+MKxuJAUjPsHk7
9vvbylOb4w5H6lo5h7kUee3w7kG+FjYVoEx+Sqq9936+KlwtN0kbiNvl0DkrXnY=
=kUmM
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull twi tracing fixes from Steven Rostedt:
"Two urgent fixes in the tracing utility.
The first is a fix for the way the ring buffer stores timestamps.
After a restructure of the code was done, the ring buffer timestamp
logic missed the fact that the first event on a sub buffer is to have
a zero delta, as the full timestamp is stored on the sub buffer
itself. But because the delta was not cleared to zero, the timestamp
for that event will be calculated as the real timestamp + the delta
from the last timestamp. This can skew the timestamps of the events
and have them say they happened when they didn't really happen.
That's bad.
The second fix is for modifying the function graph caller site. When
the stop machine was removed from updating the function tracing code,
it missed updating the function graph call site location. It is still
modified as if it is being done via stop machine. But it's not. This
can lead to a GPF and kernel crash if the function graph call site
happens to lie between cache lines and one CPU is executing it while
another CPU is doing the update. It would be a very hard condition to
hit, but the result is severe enough to have it fixed ASAP"
* tag 'trace-fixes-v3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/x86: Use breakpoints for converting function graph caller
ring-buffer: Fix first commit on sub-buffer having non-zero delta
Pull x86 EFI fixes from Peter Anvin:
"A few more EFI-related fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Check status field to validate BGRT header
x86/efi: Fix 32-bit fallout
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=DDj5
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A collection of ARM SoC fixes for v3.14-rc1.
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dma: mv_xor: Silence a bunch of LPAE-related warnings
ARM: ux500: disable msp2 device tree node
ARM: zynq: Reserve not DMAable space in front of the kernel
ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
ARM: imx6: Initialize low-power mode early again
ARM: pxa: fix various compilation problems
ARM: pxa: fix compilation problem on AM300EPD board
ARM: at91: add Atmel's SAMA5D3 Xplained board
spi/atmel: document clock properties
mmc: atmel-mci: document clock properties
ARM: at91: enable USB host on at91sam9n12ek board
ARM: at91/dt: fix sama5d3 ohci hclk clock reference
ARM: at91/dt: sam9263: fix compatibility string for the I2C
ata: sata_mv: Fix probe failures with optional phys
drivers: phy: Add support for optional phys
drivers: phy: Make NULL a valid phy reference
ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
ARM: moxart: move DMA_OF selection to driver
ARM: hisi: fix kconfig warning on HAVE_ARM_TWD
For non compressed extents, iterate_extent_inodes() gives us offsets
that take into account the data offset from the file extent items, while
for compressed extents it doesn't. Therefore we have to adjust them before
placing them in a send clone instruction. Not doing this adjustment leads to
the receiving end requesting for a wrong a file range to the clone ioctl,
which results in different file content from the one in the original send
root.
Issue reproducible with the following excerpt from the test I made for
xfstests:
_scratch_mkfs
_scratch_mount "-o compress-force=lzo"
$XFS_IO_PROG -f -c "truncate 118811" $SCRATCH_MNT/foo
$XFS_IO_PROG -c "pwrite -S 0x0d -b 39987 92267 39987" $SCRATCH_MNT/foo
$BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap1
$XFS_IO_PROG -c "pwrite -S 0x3e -b 80000 200000 80000" $SCRATCH_MNT/foo
$BTRFS_UTIL_PROG filesystem sync $SCRATCH_MNT
$XFS_IO_PROG -c "pwrite -S 0xdc -b 10000 250000 10000" $SCRATCH_MNT/foo
$XFS_IO_PROG -c "pwrite -S 0xff -b 10000 300000 10000" $SCRATCH_MNT/foo
# will be used for incremental send to be able to issue clone operations
$BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/clones_snap
$BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap2
$FSSUM_PROG -A -f -w $tmp/1.fssum $SCRATCH_MNT/mysnap1
$FSSUM_PROG -A -f -w $tmp/2.fssum -x $SCRATCH_MNT/mysnap2/mysnap1 \
-x $SCRATCH_MNT/mysnap2/clones_snap $SCRATCH_MNT/mysnap2
$FSSUM_PROG -A -f -w $tmp/clones.fssum $SCRATCH_MNT/clones_snap \
-x $SCRATCH_MNT/clones_snap/mysnap1 -x $SCRATCH_MNT/clones_snap/mysnap2
$BTRFS_UTIL_PROG send $SCRATCH_MNT/mysnap1 -f $tmp/1.snap
$BTRFS_UTIL_PROG send $SCRATCH_MNT/clones_snap -f $tmp/clones.snap
$BTRFS_UTIL_PROG send -p $SCRATCH_MNT/mysnap1 \
-c $SCRATCH_MNT/clones_snap $SCRATCH_MNT/mysnap2 -f $tmp/2.snap
_scratch_unmount
_scratch_mkfs
_scratch_mount
$BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/1.snap
$FSSUM_PROG -r $tmp/1.fssum $SCRATCH_MNT/mysnap1 2>> $seqres.full
$BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/clones.snap
$FSSUM_PROG -r $tmp/clones.fssum $SCRATCH_MNT/clones_snap 2>> $seqres.full
$BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/2.snap
$FSSUM_PROG -r $tmp/2.fssum $SCRATCH_MNT/mysnap2 2>> $seqres.full
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Because the offload mechanism can fall back to a standard transfer,
having two seperate initialization states is unfortunate. Let's just
have one state which does things consistently. This fixes a bug where
some preparation was missing when the fallback happened. And it makes
the code much easier to follow. To implement this, we put the check
if offload is possible at the top of the offload setup function.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403 (i2c: mv64xxx: Add I2C Transaction Generator support)
Here is a bunch of USB fixes for 3.14-rc3. Most of these are xhci
reverts, fixing a bunch of reported issues with USB 3 host controller
issues that loads of people have been hitting (with the exception of
kernel developers, all of our machines seem to be working fine, which is
why these took so long to get resolved...)
There are some other minor fixes and new device ids, as ususal. All
have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+iUYACgkQMUfUDdst+yl+cACeI7OnpRFgZEAS1yJOGQv0mi/m
uAEAnAw6tNMgMt+W93eIIEtw9b/dOAp2
=nQo7
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a bunch of USB fixes for 3.14-rc3. Most of these are xhci
reverts, fixing a bunch of reported issues with USB 3 host controller
issues that loads of people have been hitting (with the exception of
kernel developers, all of our machines seem to be working fine, which
is why these took so long to get resolved...)
There are some other minor fixes and new device ids, as ususal. All
have been in linux-next successfully"
* tag 'usb-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
usb: option: blacklist ZTE MF667 net interface
Revert "usb: xhci: Link TRB must not occur within a USB payload burst"
Revert "xhci: Avoid infinite loop when sg urb requires too many trbs"
Revert "xhci: Set scatter-gather limit to avoid failed block writes."
xhci 1.0: Limit arbitrarily-aligned scatter gather.
Modpost: fixed USB alias generation for ranges including 0x9 and 0xA
usb: core: Fix potential memory leak adding dyn USBdevice IDs
USB: ftdi_sio: add Tagsys RFID Reader IDs
usb: qcserial: add Netgear Aircard 340U
usb-storage: enable multi-LUN scanning when needed
USB: simple: add Dynastream ANT USB-m Stick device support
usb-storage: add unusual-devs entry for BlackBerry 9000
usb-storage: restrict bcdDevice range for Super Top in Cypress ATACB
usb: phy: move some error messages to debug
usb: ftdi_sio: add Mindstorms EV3 console adapter
usb: dwc2: fix memory corruption in dwc2 driver
usb: dwc2: fix role switch breakage
usb: dwc2: bail out early when booting with "nousb"
Revert "xhci: replace xhci_read_64() with readq()"
Revert "xhci: replace xhci_write_64() with writeq()"
...
Here are a small number of tty/serial driver fixes to resolve reported
issues with 3.14-rc and earlier (in the case of the vt bugfix.) Some of
these have been tested and reported by a number of people as the tty
bugfix was pretty commonly hit on some platforms.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+iJAACgkQMUfUDdst+ynLeACfcDynM0/zoSAvfscALTpF796A
KU8AnRyiac0BauTLDmryJSr6pJqkAzMM
=6iYo
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a small number of tty/serial driver fixes to resolve reported
issues with 3.14-rc and earlier (in the case of the vt bugfix). Some
of these have been tested and reported by a number of people as the
tty bugfix was pretty commonly hit on some platforms.
All have been in linux-next for a while"
* tag 'tty-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Fix secure clear screen
serial: 8250: Support XR17V35x fraction divisor
n_tty: Fix stale echo output
serial: sirf: fix kernel panic caused by unpaired spinlock
serial: 8250_pci: unbreak last serial ports on NetMos 9865 cards
n_tty: Fix poll() when TIME_CHAR and MIN_CHAR == 0
serial: omap: fix rs485 probe on defered pinctrl
serial: 8250_dw: fix compilation warning when !CONFIG_PM_SLEEP
serial: omap-serial: Move info message to probe function
tty: Set correct tty name in 'active' sysfs attribute
tty: n_gsm: Fix for modems with brk in modem status control
drivers/tty/hvc: don't use module_init in non-modular hyp. console code
Here are a number (lots, I know) of fixes for staging drivers to resolve
a bunch of reported issues.
The largest patches here is one revert of a patch that is in 3.14-rc1 to
fix reported problems, and a sync of a usb host driver that required
some ARM patches to go in before it could be accepted (which is why it
missed -rc1).
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+h+MACgkQMUfUDdst+ymAigCeNfR2pmw6lcNLokbdUJDOBHhX
tXwAoL4rzSeaRCu1hbTe0q7lXiZDM+yN
=aMFY
-----END PGP SIGNATURE-----
Merge tag 'staging-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a number (lots, I know) of fixes for staging drivers to
resolve a bunch of reported issues.
The largest patches here is one revert of a patch that is in 3.14-rc1
to fix reported problems, and a sync of a usb host driver that
required some ARM patches to go in before it could be accepted (which
is why it missed -rc1)
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (56 commits)
staging/rtl8821ae: fix build, depends on MAC80211
iio: max1363: Use devm_regulator_get_optional for optional regulator
iio:accel:bma180: Use modifier instead of index in channel specification
iio: adis16400: Set timestamp as the last element in chan_spec
iio: ak8975: Fix calculation formula for convert micro tesla to gauss unit
staging:iio:ad799x fix typo in ad799x_events[]
iio: mxs-lradc: remove useless scale_available files
iio: mxs-lradc: fix buffer overflow
iio:magnetometer:mag3110: Fix output of decimal digits in show_int_plus_micros()
iio:magnetometer:mag3110: Report busy in _read_raw() / write_raw() when buffer is enabled
wlags49_h2: Fix overflow in wireless_set_essid()
xlr_net: Fix missing trivial allocation check
staging: r8188eu: overflow in rtw_p2p_get_go_device_address()
staging: r8188eu: array overflow in rtw_mp_ioctl_hdl()
staging: r8188eu: Fix typo in USB_DEVICE list
usbip/userspace/libsrc/names.c: memory leak
gpu: ion: dereferencing an ERR_PTR
staging: comedi: usbduxsigma: fix unaligned dereferences
staging: comedi: fix too early cleanup in comedi_auto_config()
staging: android: ion: dummy: fix an error code
...
Here is a single driver core patch for 3.14-rc3 for the component code that
Russell has found and fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+hoYACgkQMUfUDdst+yn7wgCgslZXCrrhndQEl8A3oCBbfuWj
KgEAoMDMoPyuoCGyQaScQwQoEjYfHMba
=A+dt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single driver core patch for 3.14-rc3 for the component code
that Russell has found and fixed"
* tag 'driver-core-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base: fix devres handling for master device
Here are some small char/misc driver fixes, along with some
documentation updates, for 3.14-rc3. Nothing major, just a number of
fixes for reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+hvIACgkQMUfUDdst+ykGRQCgpi/LgypVecwQlv73TsHLNZo/
ybIAniXJlLgf4xu3q0J+8br3iQ7sg8pC
=m+up
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char/misc driver fixes, along with some
documentation updates, for 3.14-rc3. Nothing major, just a number of
fixes for reported issues"
* tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "misc: eeprom: sunxi: Add new compatibles"
Revert "ARM: sunxi: dt: Convert to the new SID compatibles"
misc: mic: fix possible signed underflow (undefined behavior) in userspace API
ARM: sunxi: dt: Convert to the new SID compatibles
misc: eeprom: sunxi: Add new compatibles
misc: genwqe: Fix potential memory leak when pinning memory
Documentation:Update Documentation/zh_CN/arm64/memory.txt
Documentation:Update Documentation/zh_CN/arm64/booting.txt
Documentation:Chinese translation of Documentation/arm64/tagged-pointers.txt
raw: set range for MAX_RAW_DEVS
raw: test against runtime value of max_raw_minors
Drivers: hv: vmbus: Don't timeout during the initial connection with host
Drivers: hv: vmbus: Specify the target CPU that should receive notification
VME: Correct read/write alignment algorithm
mei: don't unset read cb ptr on reset
mei: clear write cb from waiting list on reset
A user was running into errors from an NFS export of a subvolume that had a
default subvol set. When we mount a default subvol we will use d_obtain_alias()
to find an existing dentry for the subvolume in the case that the root subvol
has already been mounted, or a dummy one is allocated in the case that the root
subvol has not already been mounted. This allows us to connect the dentry later
on if we wander into the path. However if we don't ever wander into the path we
will keep DCACHE_DISCONNECTED set for a long time, which angers NFS. It doesn't
appear to cause any problems but it is annoying nonetheless, so simply unset
DCACHE_DISCONNECTED in the get_default_root case and switch btrfs_lookup() to
use d_materialise_unique() instead which will make everything play nicely
together and reconnect stuff if we wander into the defaul subvol path from a
different way. With this patch I'm no longer getting the NFS errors when
exporting a volume that has been mounted with a default subvol set. Thanks,
cc: bfields@fieldses.org
cc: ebiederm@xmission.com
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Chris Mason <clm@fb.com>
Currently, the only mount option for max_inline that has any effect is
max_inline=0. Any other value that is supplied to max_inline will be
adjusted to a minimum of 4k. Since max_inline has an effective maximum
of ~3900 bytes due to page size limitations, the current behaviour
only has meaning for max_inline=0.
This patch will allow the the max_inline mount option to accept non-zero
values as indicated in the documentation.
Signed-off-by: Mitch Harder <mitch.harder@sabayonlinux.org>
Signed-off-by: Chris Mason <clm@fb.com>
Given now we have 2 spinlock for management of delayed refs,
CONFIG_DEBUG_SPINLOCK=y helped me find this,
[ 4723.413809] BUG: spinlock wrong CPU on CPU#1, btrfs-transacti/2258
[ 4723.414882] lock: 0xffff880048377670, .magic: dead4ead, .owner: btrfs-transacti/2258, .owner_cpu: 2
[ 4723.417146] CPU: 1 PID: 2258 Comm: btrfs-transacti Tainted: G W O 3.12.0+ #4
[ 4723.421321] Call Trace:
[ 4723.421872] [<ffffffff81680fe7>] dump_stack+0x54/0x74
[ 4723.422753] [<ffffffff81681093>] spin_dump+0x8c/0x91
[ 4723.424979] [<ffffffff816810b9>] spin_bug+0x21/0x26
[ 4723.425846] [<ffffffff81323956>] do_raw_spin_unlock+0x66/0x90
[ 4723.434424] [<ffffffff81689bf7>] _raw_spin_unlock+0x27/0x40
[ 4723.438747] [<ffffffffa015da9e>] btrfs_cleanup_one_transaction+0x35e/0x710 [btrfs]
[ 4723.443321] [<ffffffffa015df54>] btrfs_cleanup_transaction+0x104/0x570 [btrfs]
[ 4723.444692] [<ffffffff810c1b5d>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[ 4723.450336] [<ffffffff810c1c2d>] ? trace_hardirqs_on+0xd/0x10
[ 4723.451332] [<ffffffffa015e5ee>] transaction_kthread+0x22e/0x270 [btrfs]
[ 4723.452543] [<ffffffffa015e3c0>] ? btrfs_cleanup_transaction+0x570/0x570 [btrfs]
[ 4723.457833] [<ffffffff81079efa>] kthread+0xea/0xf0
[ 4723.458990] [<ffffffff81079e10>] ? kthread_create_on_node+0x140/0x140
[ 4723.460133] [<ffffffff81692aac>] ret_from_fork+0x7c/0xb0
[ 4723.460865] [<ffffffff81079e10>] ? kthread_create_on_node+0x140/0x140
[ 4723.496521] ------------[ cut here ]------------
----------------------------------------------------------------------
The reason is that we get to call cond_resched_lock(&head_ref->lock) while
still holding @delayed_refs->lock.
So it's different with __btrfs_run_delayed_refs(), where we do drop-acquire
dance before and after actually processing delayed refs.
Here we don't drop the lock, others are not able to add new delayed refs to
head_ref, so cond_resched_lock(&head_ref->lock) is not necessary here.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
This reverts commit 01e219e806.
David Sterba found a different way to provide these features without adding a new
ioctl. We haven't released any progs with this ioctl yet, so I'm taking this out
for now until we finalize things.
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
CC: Jeff Mahoney <jeffm@suse.com>
Pull two nfsd bugfixes from Bruce Fields.
* 'for-3.14' of git://linux-nfs.org/~bfields/linux:
lockd: send correct lock when granting a delayed lock.
nfsd4: fix acl buffer overrun
both tagged for -stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=J3I5
-----END PGP SIGNATURE-----
Merge tag 'md/3.14-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Two bugfixes for md
both tagged for -stable"
* tag 'md/3.14-fixes' of git://neil.brown.name/md:
md/raid5: Fix CPU hotplug callback registration
md/raid1: restore ability for check and repair to fix read errors.
