This variable read, but never set. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that d0i3 is dead, this function can't be called from d0i3
flows. Change its signature and make it static.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For runtime PM to work with d0i3 code, a lot of integration work needs
to be done with the platform (e.g. the out-of-band wake up interrupt)
and we currently don't have any platforms where this integration
happened. So, this code has been pretty much stale for a while and
when someone enables it, it just breaks things.
Therefore, to simplify the code base and make sure no one enables this
by mistake, we will remove the whole code.
This is only the very start, much more work is needed.
Remove the places where we check iwl_mvm_is_d0i3_supported
but leave all the refs, those will be removed in a different
patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When printing a TX, add to the print the length of the frame.
That will help with BSEP (buffer status report poll) tests.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use the actual length of channels array and not the max capable length.
Signed-off-by: Beker Ayala <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
add support to print ldbg command in mvm and xvt mode
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support the new DBGC_SUSPEND_RESUME command to change the recording state.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The recording functions are quite big to be inline and the driver should
expose only the stop and restart functions that are allowed to be used
rather then the internal helper functions. Move the functions from the
header file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These static functions are only used after their definition,
so we don't need the forward declarations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case that there are OBSS that do not know how to properly
interpret 26-tone RU OFDMA transmissions, instruct the FW not
to use such transmissions.
The check is currently only performed upon association.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If mvm->fwrt.cur_fw_img != IWL_UCODE_INIT, then
rfkill_safe_init_done must be true since
rfkill_safe_init_done is set to true before we start to load
the runtime image.
Remove the redundant condition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The newer targets don't support the DQA enablement command
and will return error status, while older targets need it.
The feature is defined by the corresponding TLV.
Send the command only if the TLV is enabled.
Signed-off-by: Ilia Lin <ilia.lin@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Introduce debugfs entry to read device temperature and related cmu
command. Introduce mt7615_mcu_parse_response to parse mcu response
messages and refactor mt7615_mcu_msg_send routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_txwi_to_txp utility routine to convert mt76_txwi_cache
into mt7615_txp and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We allways return 0 from mt76x0_phy_set_channel(), no need to pass
return value upward.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We set dev->mt76.chandef in mt76_set_channel() already.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_rx_convert() not need to be exported any longer.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
tx queues are already disabled by mac80211 during scanning or other
off-channel activity. There is no need to repeat the check in mt76,
since scheduled queues are selected by mac80211 as well.
Signed-off-by: Balakrishna Bandi <b.balakrishna@globaledgesoft.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is no need to send a BAR frame after stopping aggregation, and doing
so could lead to sending class 3 frames after deauthentication from an AP
Signed-off-by: Balakrishna Bandi <b.balakrishna@globaledgesoft.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes use-after-free issues on forced station removal during hardware restart
on MT76x02
Fixes: aee5b8cf24 ("mt76: implement A-MPDU rx reordering in the driver code")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7615 chips usually come pre-calibrated, even when used on embedded boards.
In that case, the on-flash EEPROM data needs to be merged with some data
from OTP ROM.
Run this merge if the external EEPROM data is valid and OTP has valid fields.
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce a default implementation for mt76_sw_scan and
mt76_sw_scan_complete in mt76 module and remove duplicated code
since most of the drivers share the same implementation
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the following checkpatch warnings:
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Refactor mt7615_mac_wtbl_set_key and introduce
the following routines in order to configure wtbl entries
and properly add hw support to BIP_CMAC_128 cipher:
- mt7615_mac_wtbl_update_cipher
- mt7615_mac_wtbl_update_pk
- mt7615_mac_wtbl_update_key
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove unnecessary mcu queue initialization in mt7603_dma_init since it
has been already done in mt76_mmio_init
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76{15,03}_tx_tasklet in mt76_alloc_device in order to be used as
default tx_tasklet initialization. Remove duplicated code in
mt7603/mt7615 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move survey_time field in mt76_dev in order to be reused adding survey
support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce channel survey support for mt76x2u and mt76x0u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable multi-interface support for mt76x02u driver. For the moment
allow max two concurrent interfaces in order to preserve enough room
for ps traffic since we are using beacon slots for it.
I have successfully tested the following configuration:
- AP + STA
- AP0 + AP1
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not copy beacon skb in mt76x02_mac_set_beacon_enable for usb devices
since it will be done in mt76x02_update_beacon_iter. Moreover squash
mt76x02_mac_set_beacon_enable and __mt76x02_mac_set_beacon_enable since
the latter is run just by mt76x02_mac_set_beacon_enable
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce Smart Carrier Sense support in order to tune device
sensitivity according to RTS error rate and False CCA reported by the
radio
Tested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As already done for mt7603 driver, move mt76.mutex lock inside
mt7615_set_channel since we need to grab mt76.mutex in mt7615_mac_work.
This is a preliminary patch to add Smart Carrier Sense (SCS) support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
No functional change intended.
Add SPDX identifiers to all remaining files in /mt76.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the following checkpatch warnings:
ERROR: code indent should use tabs where possible
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Avoid precedence issues in macro
WARNING: Statements should start on a tabstop
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the following checkpatch warnings:
WARNING: Improper SPDX comment style
Fix blank lines.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the following checkpatch warnings:
WARNING: Improper SPDX comment style
CHECK: No space is necessary after a cast
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update the help text to fix a checkpatch warning:
WARNING: please write a paragraph that describes the config symbol fully
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add default values of cw_min/max and use fls() for configuration.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware supports 4 sets of WMM that should be put to good use.
And fix incorrect queue mapping in mt7615_conf_tx().
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Convert MT7603_WATCHDOG_TIME in jiffies rescheduling watchdog delayed
work
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Express watchdog timeout in jiffies since it is used directly in
ieee80211_queue_delayed_work
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76_mmio_read_copy routine and the related function pointer in
mt76_bus_ops data structure. mt76_mmio_read_copy will be used to add
BIP_CMAC_128 cipher hw support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce set_key_cmd and mt76_wcid pointer to mt7615_mac_wtbl_set_key
signature and do not set key to NULL if cmd is DISABLE_KEY.
This is a preliminary patch to add BIP_CMAC_128 hw support to mt7615
driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Get rid of wtbl_sec_key definition since it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7615_mac_wtbl_set_key routine to configure wtbl key parameter
directly from host cpu. This is a preliminary patch to add BIP_CMAC_128
hw support. Moreover add static qualifier to mt7615_mac_get_key_info
routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mac_wtbl_addr rouinte to compute sta wtbl address.
This is a preliminary patch to update wtbl key directly from host
processor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to update wtbl key directly from host
processor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- initialize CCA signal source
- initialize clock for band 1 (7615D)
- initialize BAR rate
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support to TP-Link T2UHP
https://wikidevi.com/wiki/TP-LINK_Archer_T2UHP
Tested-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Compiler give us guarantees on variables alignment, so use
an variable as buffer when read/write registers and remove
unneeded {put,get}_unaligned.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In contrast to mt76_wr() which we use to program registers,
on mt76_wr_copy() we should not change endian of the data.
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bufferable management frames need to be put in the data queue, otherwise
they will not be buffered when the receiver is asleep.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The hardware expects MT_TX_RATE_NSS to be filled with the number of
space/time streams. For non-STBC rates, this is equal to nss.
For 1-stream STBC, this needs to be set to 2.
This is relevant for VHT rates only, on HT, the value is derived from MCS
internally.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix typo setting urb->transfer_buffer_length in mt76u_fill_rx_sg
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Fixes: f8f527b16d ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
- Switch from lower rates to higher rates more conservatively
- enable hardware rate up/down selection
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These values must be initialized to zero, otherwise the hardware could
reuse previous values, especially the rate index
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It bypasses the MCU, so it does not belong in mcu.c
Also make mt7615_mac_tx_rate_val static
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7615_mcu_send_ram_firmware routine since mt7615_load_ram runs the
same code to send ram firmware to cr4 and n9 mcus. Moreover rename
gen_dl_mode in mt7615_mcu_gen_dl_mode.
This patch does not introduce any behaviour change, it is just code
refactor.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Release patch semaphore even if request_firmware fails in
mt7615_load_patch
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we don't clean that tx queue from the tx tasklet, we need to do it
after the firmware upload is done. This patch also adds a cleanup step during
the upload, to help reclaim memory faster.
Fixes unprocessed queued frames eating up memory long after the firmware
upload has already completed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mcu_rdd_send_pattern routine to trigger a radar pattern
detection. Moreover move debugfs related routines in a dedicated source
file.
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add Channel Switch Announcement support to mt7615 driver updating beacon
template with CSA IE received from mac80211
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Delay channel calibration after Channel Availability Check. Add some
code cleanup to mt7615_mcu_set_channel
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add hw radar detection support to mt7615 driver in order to
unlock dfs channels on 5GHz band
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_regd_notifier callback. This is a preliminary patch to
add radar detection support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the following sparse warning in __mt7615_mcu_msg_send:
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
restricted __le16 degrades to integer
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
cast from restricted __le16
Fixes: 04b8e65922 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When beacon length is not a multiple of 4, the beacon could be sent with
the last 1-3 bytes corrupted. The skb data is guaranteed to have enough
room for reading beyond the end, because it is always followed by
skb_shared_info, so rounding up is safe.
All other callers of mt76_wr_copy have multiple-of-4 length already.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The `ar_usb` field of `ath6kl_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath6kl_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath6kl_usb_setup_pipe_resources`:
for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
endpoint = &iface_desc->endpoint[i].desc;
// get the address from endpoint descriptor
pipe_num = ath6kl_usb_get_logical_pipe_num(ar_usb,
endpoint->bEndpointAddress,
&urbcount);
......
// select the pipe object
pipe = &ar_usb->pipes[pipe_num];
// initialize the ar_usb field
pipe->ar_usb = ar_usb;
}
The driver assumes that the addresses reported in endpoint
descriptors from device side to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath6kl_usb_alloc_urb_from_pipe` and
`ath6kl_usb_free_urb_to_pipe`.
This patch fixes the bug by preventing potential NULL-ptr-deref
(CVE-2019-15098).
Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clang triggers a warning about oversized stack frames that gcc does not
notice because of slightly different inlining decisions:
ath/wcn36xx/smd.c:1409:5: error: stack frame size of 1040 bytes in function 'wcn36xx_smd_config_bss' [-Werror,-Wframe-larger-than=]
ath/wcn36xx/smd.c:640:5: error: stack frame size of 1032 bytes in function 'wcn36xx_smd_start_hw_scan' [-Werror,-Wframe-larger-than=]
Basically the wcn36xx_hal_start_scan_offload_req_msg,
wcn36xx_hal_config_bss_req_msg_v1, and wcn36xx_hal_config_bss_req_msg
structures are too large to be put on the kernel stack, but small
enough that gcc does not warn about them.
Use kzalloc() to allocate them all. There are similar structures in other
parts of this driver, but they are all smaller, with the next largest
stack frame at 480 bytes for wcn36xx_smd_send_beacon.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath6kl_htc_mbox_create(), when kzalloc() on line 2855 fails,
target->dev is assigned to NULL, and ath6kl_htc_mbox_cleanup(target) is
called on line 2885.
In ath6kl_htc_mbox_cleanup(), target->dev is used on line 2895:
ath6kl_hif_cleanup_scatter(target->dev->ar);
Thus, a null-pointer dereference may occur.
To fix this bug, kfree(target) is called and NULL is returned when
kzalloc() on line 2855 fails.
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize acktimeout to the maximum configurable value in
ath_dynack_reset in order to not disconnect long distance static links
enabling dynack and even to take care of possible errors configuring
a static timeout. Moreover initialize station timeout value to the current
acktimeout value
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Compute maximum configurable ackimeout/ctstimeout according to channel
width (clockrate)
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add compute timeout to last computation timestamp in
ath_dynack_reset in order to not run ath_dynack_compute_ackto
immediately
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce ath_dynack_set_timeout routine to configure slottime/ack/cts
timeouts and remove duplicated code
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Atheros cards with a AR92XX generation (and older) chip usually
store their pci(e) initialization vectors on an external eeprom chip.
However these chips technically don't need the eeprom chip attached,
the AR9280 Datasheet in section "6.1.2 DEVICE_ID" describes that
"... if the EEPROM content is not valid, a value of 0xFF1C returns
when read from the register". So, they will show up on the system's
pci bus. However in that state, ath9k can't load, since it relies
on having the correct pci-id, otherwise it doesn't know what chip it
actually is. This happens on many embedded devices like routers
and accesspoint since they want to keep the BOM low and store the
pci(e) initialization vectors together with the calibration data
on the system's FLASH, which is out of reach of the ath9k chip.
Furthermore, Some devices (like the Cisco Meraki Z1 Cloud Managed
Teleworker Gateway) need to be able to initialize the PCIe wifi device.
Normally, this should be done as a pci quirk during the early stages of
booting linux. However, this isn't possible for devices which have the
init code for the Atheros chip stored on NAND in an UBI volume.
Hence, this module can be used to initialize the chip when the
user-space is ready to extract the init code.
Martin Blumenstingl prodived the following fixes:
owl-loader: add support for OWL emulation PCI devices
owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
owl-loader: use dev_* instead of pr_* logging functions
owl-loader: auto-generate the eeprom filename as fallback
owl-loader: add a debug message when swapping the eeprom data
owl-loader: add missing newlines in log messages
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/carl9170/usb.c: In function carl9170_usb_disconnect:
drivers/net/wireless/ath/carl9170/usb.c:1110:21:
warning: variable udev set but not used [-Wunused-but-set-variable]
It is not use since commit feb09b2933 ("carl9170:
fix misuse of device driver API")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A null pointer would be passed to a call of the function “kfree”
directly after a call of the function “kcalloc” failed at one place.
Remove this superfluous function call.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11.
wil6210 reports it's EDMG capabilities (that are also based on FW
capability) to cfg80211 by filling
wiphy->bands[NL80211_BAND_60GHZ]->edmg_cap.
wil6210 handles edmg.channels and edmg.bw_config requested in connect
and start_ap operations.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several occasions where a negative cid value is passed
into wil_cid_valid and this is converted into a u8 causing the
range check of cid >= 0 to always succeed. Fix this by making
the cid argument an int to handle any -ve error value of cid.
An example of this behaviour is in wil_cfg80211_dump_station,
where cid is assigned -ENOENT if the call to wil_find_cid_by_idx
fails, and this -ve value is passed to wil_cid_valid. I believe
that the conversion of -ENOENT to the u8 value 254 which is
greater than wil->max_assoc_sta causes wil_find_cid_by_idx to
currently work fine, but I think is by luck and not the
intended behaviour.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
`dev` (struct rsi_91x_usbdev *) field of adapter
(struct rsi_91x_usbdev *) is allocated and initialized in
`rsi_init_usb_interface`. If any error is detected in information
read from the device side, `rsi_init_usb_interface` will be
freed. However, in the higher level error handling code in
`rsi_probe`, if error is detected, `rsi_91x_deinit` is called
again, in which `dev` will be freed again, resulting double free.
This patch fixes the double free by removing the free operation on
`dev` in `rsi_init_usb_interface`, because `rsi_91x_deinit` is also
used in `rsi_disconnect`, in that code path, the `dev` field is not
(and thus needs to be) freed.
This bug was found in v4.19, but is also present in the latest version
of kernel. Fixes CVE-2019-15504.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 9ad3b55654.
As reported by Sergey:
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by
9ad3b55654 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Cc: <stable@vger.kernel.org> # v5.1+
Reported-and-tested-by: Sergey Maranchuk <slav0nic0@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After looking at code I realized that my previous fix
9584412438 ("rt2x00: clear IV's on start to fix AP mode regression")
was incomplete. We can still have wrong IV's after re-keyring.
To fix that, clear up IV's also on key removal.
Fixes: 710e6cc159 ("rt2800: do not nullify initialization vector data")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
tested-by: Emil Karlson <jekarl@iki.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We were erroneously assigning the new configuration to a local
variable cfg, but that was not being assigned to anything, so the
change was getting lost. Assign directly to iwl_trans->cfg instead.
Fixes: 5a8c31aa63 ("iwlwifi: pcie: fix recognition of QuZ devices")
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_update_vs_ie(),mwifiex_set_uap_rates() and
mwifiex_set_wmm_params() call memcpy() without checking
the destination size.Since the source is given from
user-space, this may trigger a heap buffer overflow.
Fix them by putting the length check before performing memcpy().
This fix addresses CVE-2019-14814,CVE-2019-14815,CVE-2019-14816.
Signed-off-by: Wen Huang <huangwenabc@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.comg>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MT7630E hardware does support 5GHz, but we do not properly configure phy
for 5GHz channels. Scanning at this band not only do not show any APs
but also can hang the firmware.
Since vendor reference driver do not support 5GHz we don't know how
properly configure 5GHz channels. So disable this band for MT7630E .
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
I can observe firmware hangs on MT7630E on station mode: tx stop
functioning after minor activity (rx keep working) and on module
unload device fail to stop with messages:
[ 5446.141413] mt76x0e 0000:06:00.0: TX DMA did not stop
[ 5449.176764] mt76x0e 0000:06:00.0: TX DMA did not stop
Loading module again results in failure to associate with AP.
Only machine power off / power on cycle can make device work again.
It's unclear why commit 41634aa8d6 causes the problem, but it is
related to HW encryption. Since issue is a firmware hang, that is super
hard to debug, just disable HW encryption as fix for the issue.
Fixes: 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct usb_int_regs {
...
struct reg_data regs[0];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following function:
static int usb_int_regs_length(unsigned int count)
{
return sizeof(struct usb_int_regs) + count * sizeof(struct reg_data);
}
with:
struct_size(regs, regs, count)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Getting RAM info just once per driver's lifetime (during chip
recognition) is not enough as it may get adjusted later (depending on
the used firmware). Subsequent inits may load different firmwares so a
full RAM recognition is required on every PCIe setup. This is especially
important since implementing hardware reset on a firmware crash.
Moreover calling brcmf_chip_get_raminfo() makes sure that RAM core is
up. It's important as having BCMA_CORE_SYS_MEM down on BCM4366 was
resulting in firmware failing to initialize and following error:
[ 65.657546] brcmfmac 0000:01:00.0: brcmf_pcie_download_fw_nvram: Invalid shared RAM address 0x04000001
This change makes brcmf_chip_get_raminfo() call during chip recognition
redundant for PCIe devices but SDIO and USB still need it and it's a
very small overhead anyway.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The strncpy() may truncate the copied string,
replace it by the safer strscpy().
To avoid below compile warning with gcc 8.2:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:In function 'brcmf_vndr_ie':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:4227:2:
warning: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Wstringop-truncation]
strncpy(iebuf, add_del_cmd, VNDR_IE_CMD_LEN - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
According to documentation IEEE80211_TX_STAT_AMPDU_NO_BACK is suppose
to be used when we do not recive BA (BlockAck). However on rt2x00 we
use it when remote station fail to decode one or more subframes within
AMPDU (some bits are not set in BlockAck bitmap). Setting the flag result
in sent of BAR (BlockAck Request) frame and this might result of abuse
of BA session, since remote station can sent BA with incorrect
sequence numbers after receiving BAR. This problem is visible especially
when connecting two rt2800 devices.
Previously I observed some performance benefits when using the flag
when connecting with iwlwifi devices. But currently possibly due
to reacent changes in rt2x00 removing the flag has no effect on
those test cases.
So remove the IEEE80211_TX_STAT_AMPDU_NO_BACK.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a spelling mistake in an IPW_DEBUG_INFO message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In proc_BSSList_open(), 'file->private_data' is allocated through kzalloc()
and 'data->rbuffer' is allocated through kmalloc(). In the following
execution, if an error occurs, they are not deallocated, leading to memory
leaks. To fix this issue, free the allocated memory regions before
returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function is called before the lock which is asserted was ever used.
Just remove it.
Reported-by: syzbot+74c65761783d66a9c97c@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The pointer hash is being initialized with a value that is never read
and is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In wlc_phy_radio_init_2056(), regs_SYN_2056_ptr, regs_TX_2056_ptr and
regs_RX_2056_ptr may be not assigned, and thus they are still NULL.
Then, they are used on lines 20042-20050:
wlc_phy_init_radio_regs(pi, regs_SYN_2056_ptr, (u16) RADIO_2056_SYN);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX0);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX1);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX0);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX1);
Thus, possible null-pointer dereferences may occur.
To avoid these bugs, when these variables are not assigned,
wlc_phy_radio_init_2056() directly returns.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MSI interrupt should be enabled on certain platform.
Add a module parameter disable_msi to disable MSI interrupt,
driver will then use legacy interrupt instead.
One could rebind the PCI device, probe() will pick up the
new value of the module parameter. Such as:
echo '0000:01:00.0' > /sys/bus/pci/drivers/rtw_pci/unbind
echo '0000:01:00.0' > /sys/bus/pci/drivers/rtw_pci/bind
Tested-by: Ján Veselý <jano.vesely@gmail.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a mass of jobs between spin lock and unlock in the hardware
IRQ which will occupy much time originally. To make system work more
efficiently, this patch moves the jobs to the soft IRQ (bottom half) to
reduce the time in hardware IRQ.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer debugfs_topdir is initialized to a value that is never read
and it is re-assigned later. The initialization is redundant and can
be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
0day reports:
sparse warnings:
drivers/net/wireless/realtek/rtw88/coex.c:2457:6: sparse:
symbol 'rtw_coex_coex_dm_reset' was not declared. Should it be static?
rtw_coex_coex_dm_reset() is not called. Remove it.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WARN_ON() macro takes a condition, not a warning message. I've
changed this to use WARN() instead.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 98fd8db59a ("rtlwifi: rtl8192ce: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 98fd8db59a ("rtlwifi: rtl8192ce: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 36eda7568f ("rtlwifi: rtl8188ee: Convert macros that set
descriptor"), all the routines that get fields from a descriptor were
changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 36eda7568f ("rtlwifi: rtl8188ee: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit bd421dab75 ("rtlwifi: rtl8821ae: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: bd421dab75 ("rtlwifi: rtl8821ae: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
and other warnings are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the TX and RX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A number of variables are initialized when declared that set later in the
routine, thus the initialization can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the call to hw_init() fails for any of the drivers, the driver will
leak memory that was allocated in BT coexistence setup. Technically, each
of the drivers should have done this free; however placing it in rtl_pci
fixes all the drivers with only a single patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/realtek/rtlwifi/efuse.c:16:31:
warning: RTL8712_SDIO_EFUSE_TABLE defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/efuse.c:9:17:
warning: MAX_PGPKT_SIZE defined but not used [-Wunused-const-variable=]
They are never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the process of converting the bit manipulation macros were converted
to use GENMASK(), the compiler reported a value too big for the field.
The offending statement was trying to write 0x100 into a 5-bit field.
An accompaning comment says to set bit 3, thus the code is changed
appropriately.
This error has been in the driver since its initial submission.
Fixes: 29d00a3e46 ("rtlwifi: rtl8192cu: Add routine trx")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix spurious warning message when building with W=1:
CC [M] drivers/net/wireless/realtek/rtlwifi/usb.o
drivers/net/wireless/realtek/rtlwifi/usb.c:243: warning: Cannot understand * on line 243 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:760: warning: Cannot understand * on line 760 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:790: warning: Cannot understand * on line 790 - I thought it was a doc line
Clean up the comment format.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to use a different firmware for C0 versions of killer Qu NICs.
Add structures for them and handle them in the if block that detects
C0 revisions.
Additionally, instead of having an inclusive check for QnJ devices,
make the selection exclusive, so that switching to QnJ is the
exception, not the default. This prevents us from having to add all
the non-QnJ cards to an exclusion list. To do so, only go into the
QnJ block if the device has an RF ID type HR and HW revision QnJ.
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the HW revision of Qu devices we found is QuZ, then we need to
switch the configuration accordingly in order to use the correct FW.
Add a block of ifs in order do that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have a too generic condition that switches from Qu configurations
to QnJ configurations. We need to exclude some configurations so that
they are not erroneously switched. Add the ax201 configuration to the
list of exclusions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Starting from 22560, the byte count is expected to be in
bytes and we have now 14 bits. Ajust the code to this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The MAC context configuration always allowed multicast data frames
to pass to the driver for all MAC context types, and in the
case of station MAC context both when associated and when not
associated.
One of the outcomes of this configuration is having the FW forward
encrypted multicast frames to the driver with Rx status indicating
that the frame was not decrypted (as expected, since no keys were
configured yet) which in turn results with unnecessary error
messages.
Change this behavior to allow multicast data frames only when they
are actually expected, e.g., station MAC context is associated etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To do not brake HW restart we should keep initialization vectors data.
I assumed that on start the data is already initialized to zeros, but
that not true on some scenarios and we should clear it. So add
additional flag to check if we are under HW restart and clear IV's
data if we are not.
Patch fixes AP mode regression.
Reported-and-tested-by: Emil Karlson <jekarl@iki.fi>
Fixes: 710e6cc159 ("rt2800: do not nullify initialization vector data")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.4.
Major changes:
brcmfmac
* enable 160 MHz channel support
rt2x00
* add support for PLANEX GW-USMicroN USB device
rtw88
* add Bluetooth coexistance support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdWsySAAoJEG4XJFUm622b0I4H/3dnhfTUYeP6+2T5Q2KWJOKh
+uMLGBz+vzOaRoUFM6+Ar2rT7nUT3ias+XuWiVJ2R0HrgtYeXZrdOwPjbvrpMOkl
kEZAwc174HzGaGeNzF8WT5OLLqap/v18dc8HnstI49vsPzaY7PWLmDkXeTR65x+4
6sG0aj/Ggqv2pnEdhJhGPdR6G6R6AKCL50LiMpZNeDUolCtR15IOlZDubZ3VBbFr
ubAgOqmIeeXdix0yaKWycxDO0h8OQOBE09rT796FIhzss6DRAE8mWJjqllFp1rIp
JMbzcMcsTUXPV8tXcmlqPfTAFRkIu/RbO2prHHBu7A+kuHQfdpRlpA8EpUxB2IQ=
=6nQp
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-08-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.4
First set of patches for 5.4.
Major changes:
brcmfmac
* enable 160 MHz channel support
rt2x00
* add support for PLANEX GW-USMicroN USB device
rtw88
* add Bluetooth coexistance support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for 5.3. Lots of iwlwifi fixes have accumulated
which consists most of patches in this pull request. Only most notable
iwlwifi fixes are listed below.
mwifiex
* fix a regression related to WPA1 networks since v5.3-rc1
iwlwifi
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdSWJ0AAoJEG4XJFUm622bwb4H/1cbH/VoPkNPfRb6783G3Fuc
SWcI655nMDHY3cElhLPGQrR4OuNYbFpBDT7O73XMIVqnkHlgq3L/VZD2qaacSd4H
tY4HEkkHobil9gdsEt8hpBstp9xNi36klDiq9gEOLT88eatdukCZTsCnBwaTFSEQ
84QxsVsHWuB+khVDay6jprA+vwL6YopOlPwfY9+q0LHWCHq1C98ZqPZoxjb8dzN7
bbW4hWIhMHRtN9ixPwvoRhscev2ZgRPHAncoGFE8bmRM79srZpG0mDeAhQPLGrJz
YSoGtylHpQxg3vzz2y80fMpH6jsUHFeA56xuKPQ5gnUm4bPeFbhx7h29DuABsAw=
=GDUP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-08-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.3
Second set of fixes for 5.3. Lots of iwlwifi fixes have accumulated
which consists most of patches in this pull request. Only most notable
iwlwifi fixes are listed below.
mwifiex
* fix a regression related to WPA1 networks since v5.3-rc1
iwlwifi
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cond_resched() can be used unconditionally. If CONFIG_PREEMPT is set, it
becomes a NOP scheduler wise.
Also the B43_BUG_ON() in that wrapper is a homebrewn variant of
__might_sleep() which is part of cond_resched() already.
Remove the cruft and invoke cond_resched() directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 437322ea2a.
This above-mentioned "fix" does not actually do anything to prevent a
race condition. It simply papers over it so that the issue doesn't
appear.
If this is a real problem, it should be explained better than the above
commit does, and an alternative, non-racy solution should be found.
For further reason to revert this: there's no reason we can't try
resetting the card when it's *actually* stuck in host-sleep mode. So
instead, this is unnecessarily creating scenarios where we can't recover
Wifi (and in fact, I'm fielding reports of Chromebooks that can't
recover after the aforementioned commit).
Note that this was proposed in 2017 and Ack'ed then, but due to my
marking as RFC, it never went anywhere:
https://patchwork.kernel.org/patch/9657277/
[RFC] Revert "mwifiex: fix system hang problem after resume"
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Amitkumar Karwar <amitkarwar@gmail.com>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since
WiFi and BT use 2.4GHz to transmit, it is important to
make sure they run concurrently without interfering each
other. To achieve this, WiFi driver requires a mechanism
to collaborate with BT, whether they share the antenna(s)
or not.
The final decision made by the co-existence mechanism is
to choose a proper strategy, or called "tdma/table", and
inform either firmware or hardware of the strategy.
To choose a strategy, co-existence mechanism needs to
have enough information from WiFi and BT.
BT information is provided through firmware C2H.
The contents describe the current status of BT, such as
if BT is connected or is idle, or the profile that is
being used.
WiFi information can be provided by WiFi itself. The WiFi
driver will call various of "notify" functions each time
the state of WiFi changed, such as WiFi is going to switch
channel or is connected. Also WiFi driver can know if it
shares antenna with BT by reading efuse content. Antenna
configuration of the module will finally get a different
strategy.
Upon receiving any information from WiFi or BT, the WiFi
driver will run the co-existence mechanism immediately.
It will set the RF antenna configuration according to the
strategy through the TDMA H2C to firmware and a hardware
table. Based on the tdma/table, WiFi + BT should work with
each other, and having a better user experience.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
C2H commands that cannot be handled in IRQ context should
be protected by rtwdev->mutex. Because they might have a
sequece of hardware operations that does not want to be
interfered.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the c2h operations are small and can be done
under interrupt context. For the rest that requires
more operations or can go sleep, enqueue onto c2h queue.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The configuration variable IS_LITTLE_ENDIAN is replaced by the standard
__LITTLE_ENDIAN. In addition, an unused struct is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add a device ID for PLANEX GW-USMicroN.
Without this patch, I had to echo the device IDs in order to
recognize the device.
# lsusb |grep PLANEX
Bus 002 Device 005: ID 2019:ed14 PLANEX GW-USMicroN
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtw88/pci.c: In function 'rtw_pci_phy_cfg':
drivers/net/wireless/realtek/rtw88/pci.c:993:6: warning:
variable 'ip_sel' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function 'brcms_c_set_gmode':
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5257:7: warning: variable 'preamble_restrict' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5256:6: warning: variable 'preamble' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5251:7: warning: variable 'shortslot_restrict' set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable err is initialized to a value that is never read and it
is re-assigned later. The initialization is redundant and can
be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issue: While removing and inserting the driver module, observed driver
loading is not successful.
Root cause: Card is not resetted completely without issuing cmd5.
Fix: Issued cmd5 properly.
Signed-off-by: Ganapathi Kondraju <ganapathirajukondraju@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The lbs_process_rxed_packet() frees the skb. It didn't originally, but
we fixed it in commit f54930f363 ("libertas: don't leak skb on receive
error").
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
devm_kzalloc may fail and return NULL. So the null check is needed.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2962:5: warning: variable dtim_period set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2961:6: warning: variable beacon_interval set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now _rtl_dump_channel_map() does not do any actual
thing using the channel. So remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issue: RS-9116 Card is not responding after firmware got loaded.
Root cause: After firmware got loaded, we need to reset the program
counter and few device specific registers. Those registers were not
resetted properly.
Fix: Properly resetting those registers.
Signed-off-by: Ganapathi Kondraju <ganapathirajukondraju@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Surrounding code uses -ERRNO as a result, so don't pass plain -1.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We're just trusting that these tables are of the right dimensions, when
we could do better by just using the struct directly. Let's expose the
struct txpwr_lmt_cfg_pair instead.
The table changes were made by using some Vim macros, so that should
help prevent any translation mistakes along the way.
Remaining work: get the 'void *data' out of the generic struct
rtw_table; all of these tables really deserve to be their own data
structure, with proper type fields.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* lots more HE (802.11ax) support, particularly things
relevant for the the AP side, but also mesh support
* debugfs cleanups from Greg
* some more work on extended key ID
* start using genl parallel_ops, as preparation for
weaning ourselves off RTNL and getting parallelism
* various other changes all over
-----BEGIN PGP SIGNATURE-----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=eUnh
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a reasonably large number of changes:
* lots more HE (802.11ax) support, particularly things
relevant for the the AP side, but also mesh support
* debugfs cleanups from Greg
* some more work on extended key ID
* start using genl parallel_ops, as preparation for
weaning ourselves off RTNL and getting parallelism
* various other changes all over
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Notably:
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
-----BEGIN PGP SIGNATURE-----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=7W8I
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-fixes-for-kvalo-2019-07-30' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
We have a lot of fixes, most of them are also applicable to stable.
Notably:
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing the hdr of an skb that was consumed already isn't
a good idea.
First ask if the skb is a QoS packet, then keep that data
on stack, and then consume the skb.
This was spotted by KASAN.
Cc: stable@vger.kernel.org
Fixes: 08f7d8b69a ("iwlwifi: mvm: bring back mvm GSO code")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The index for the elements of the ACPI object we dereference
was static. This means that if we called the function twice
we wouldn't start from 3 again, but rather from the latest
index we reached in the previous call.
This was dutifully reported by KASAN.
Fix this.
Cc: stable@vger.kernel.org
Fixes: 6996490501 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to remember how to unmap a memory (as single or
as page), we maintain a bit per Transmit Buffer (TBs) in
the meta data (structure iwl_cmd_meta).
We maintain a bitmap: 1 bit per TB.
If the TB is set, we will free the memory as a page.
This bitmap was never cleared. Fix this.
Cc: stable@vger.kernel.org
Fixes: 3cd1980b0c ("iwlwifi: pcie: introduce new tfd and tb formats")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We erroneously added a check for FW API version 41 before sending
GEO_TX_POWER_LIMIT, but this was already implemented in version 38.
Additionally, it was cherry-picked to older versions, namely 17, 26
and 29, so check for those as well.
Cc: stable@vger.kernel.org
Fixes: eca1e56cee ("iwlwifi: mvm: don't send GEO_TX_POWER_LIMIT to old firmwares")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a few PCI ID'S for 9000 series.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
lq_info is an arary of size 2, active_tbl index is u8.
When accessing lq_info[1 - active_tbl], theoretically it's possible
that the access will be made to a negative index value.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An earlier patch made sure that the queues are not lagging
too far behind. This means that iwl_mvm_release_frames
should not be called with a head_sn too far behind NSSN.
Don't take the risk to change completely the entry
condition to iwl_mvm_release_frames, but don't update
the head_sn is the NSSN is more than 2048 packets ahead
of us. Since this just cannot be right. This means that
the scenario described here happened. We are queue 0.
Q:0 Q:1
head_sn: 0 -> 2047
head_sn: 2048
Lots of packets arrive:
head_sn: 2047 -> 2150
send NSSN_SYNC notification
Handle notification
from the firmware and
do NOT move the head_sn
back to 2048
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The solution with the worker still had a bug, as in order
to get sta, rcu_read_lock should be used and thus no mutex
can be used inside iwl_mvm_rs_rate_init.
Also, spin_lock is a simpler solution, no need to spawn a
dedicated worker.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only place where the command was sent as SYNC is during
init and this is not really critical. This change is required
for replacing RS mutex with a spinlock (in the subsequent patch),
since SYNC comamnd requres sleeping and thus the flow cannot
be done when holding a spinlock.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comparison of the u32 variable wgds_tbl_idx with less than zero is
always going to be false because it is unsigned. Fix this by making
wgds_tbl_idx a plain signed int.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: 4fd445a2c8 ("iwlwifi: mvm: Add log information about SAR status")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code clearly never could have worked, since it locks
while already locked. Add an unlocked __iwl_mvm_mac_set_key()
variant that doesn't do locking to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver should call iwl_dbg_tlv_free even if debugfs is not defined
since ini mode does not depend on debugfs ifdef.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 68f6f492c4 ("iwlwifi: trans: support loading ini TLVs from external file")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ini debug mode should work even if debug override is not defined.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 68f6f492c4 ("iwlwifi: trans: support loading ini TLVs from external file")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_rs_tx_status can be called from two places in the code, but the
mutex is taken only on one of the calls. Split it into a wrapper taking
locks and an internal __iwl_mvm_rs_tx_status function.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support MSI-X efficiently, we want to avoid
communication across Rx queues. Each Rx queue should have
all the data it needs to process a packet.
The reordering buffer is a challenge in the MSI-X world
since we can have a single BA session whose packets are
directed to different queues. This is why each queue has
its own reordering buffer. The hardware is able to hint
the driver whether we have a hole or not, which allows
the driver to know whether it can release a packet or not.
This indication is called NSSN. Roughly, if the packet's
SN is lower than the NSSN, we can release the packet to
the stack. The NSSN is the SN of the newest packet received
without any holes + 1.
This is working as long as we don't have packets that we
release because of a timeout. When that happens, we could
have taken the decision to release a packet after we have
been waiting for its predecessor for too long. If this
predecessor comes later, we have to drop it because we
can't release packets out of order. In that case, the
hardware will give us an indication that we can we release
the packet (SN < NSSN), but the packet still needs to be
dropped.
This is why we sometimes need to ignore the NSSN and we
track the head_sn in software.
Here is a specific example of this:
1) Rx queue 1 got packets: 480, 482, 483
2) We release 480 to to the stack and wait for 481
3) NSSN is now 481
4) The timeout expires
5) We release 482 and 483, NSSN is still 480
6) 481 arrives its NSSN is 484.
We need to drop 481 even if 481 < 484. This is why we'll
update the head_sn to 484 at step 2. The flow now is:
1) Rx queue 1 got packets: 480, 482, 483
2) We release 480 to to the stack and wait for 481
3) NSSN is now 481 / head_sn is 481
4) The timeout expires
5) We release 482 and 483, NSSN is still 480 but head_sn is 484.
6) 481 arrives its NSSN is 484, but head_sn is 484 and we drop it.
This code introduces another problem in case all the traffic
goes well (no hole, no timeout):
Rx queue 1: 0 -> 483 (head_sn = 484)
Rx queue 2: 501 -> 4095 (head_sn = 0)
Rx queue 2: 0 -> 480 (head_sn = 481)
Rx queue 1: 481 but head_sn = 484 and we drop it.
At this point, the SN of queue 1 is far behind: more than
4040 packets behind. Queue 1 will consider 481 "old"
because 481 is in [501-64:501] whereas it is a very new
packet.
In order to fix that, send an Rx notification from time to
time (twice across the full set of 4096 packets) to make
sure no Rx queue is lagging too far behind.
What will happen then is:
Rx queue 1: 0 -> 483 (head_sn = 484)
Rx queue 2: 501 -> 2047 (head_sn = 2048)
Rx queue 1: Sync nofication (head_sn = 2048)
Rx queue 2: 2048 -> 4095 (head_sn = 0)
Rx queue 1: Sync notification (head_sn = 0)
Rx queue 2: 1 -> 481 (head_sn = 482)
Rx queue 1: 481 and head_sn = 0.
In queue 1's data, head_sn is now 0, the packet coming in
is 481, it'll understand that the new packet is new and it
won't be dropped.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of allocating memory for which we have an upper
limit, use a small buffer on stack.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will soon be using a new notification that will be
initiated by the driver, sent to the firmware and sent
back to all the RSS queues by the firmware. This new
notification will be useful to synchronize the NSSN across
all the queues.
For now, don't send the notification, just add the code to
handle it. Later patch will add the code to actually send
it.
While at it, validate the baid coming from the firmware to
avoid accessing an array with a bad index in the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will need a new type of synchronization message going
through all the RSS queues. Prepare the ground for this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
