When key_exchange is disabled, there is no reason to accept MSG_CRYPTO
msgs if it doesn't send MSG_CRYPTO msgs.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DMA threshold mode, frame underflow errors may sometimes occur when
the TC(threshold control) value is not enough. The TC value need to be
bumped up in this case.
There is no underflow interrupt bit on DMA_CH(#i)_Status of dwmac4, so
the DMA threshold cannot be bumped up in stmmac_dma_interrupt(). The
i.mx8mp board observed an underflow error while running NFS boot, the
NFS rootfs could not be mounted.
The underflow error can be got from the DMA descriptor TDES3 on dwmac4.
This patch bump up tc value once underflow error is got from TDES3.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Replace DSA dp->priv with tagger-owned storage
Ansuel's recent work on qca8k register access over Ethernet:
https://patchwork.kernel.org/project/netdevbpf/cover/20211207145942.7444-1-ansuelsmth@gmail.com/
has triggered me to do something which I should've done for a longer
time:
https://patchwork.kernel.org/project/netdevbpf/patch/20211109095013.27829-7-martin.kaistra@linutronix.de/#24585521
which is to replace dp->priv with something that has less caveats.
The dp->priv was introduced when sja1105 needed to hold stateful
information in the tagging protocol driver. In that design, dp->priv
held memory allocated by the switch driver, because the tagging protocol
driver design was 100% stateless.
Some years have passed and others have started to feel the need for
stateful information kept by the tagger, as well as passing data back
and forth between the tagging protocol driver and the switch driver.
This isn't possible cleanly in DSA due to a circular dependency which
leads to broken module autoloading:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
This patchset introduces a framework that resembles something normal,
which allows data to be passed from the tagging protocol driver (things
like switch management packets, which aren't intended for the network
stack) to the switch driver, while the tagging protocol still remains
more or less stateless. The overall design of the framework was
discussed with Ansuel too and it appears to be flexible enough to cover
the "register access over Ethernet" use case. Additionally, the existing
uses of dp->priv, which have mainly to do with PTP timestamping, have
also been migrated.
Changes in v2:
Fix transient build breakage in patch 5/11 due to a missing parenthesis,
https://patchwork.hopto.org/static/nipa/592567/12665213/build_clang/
and another transient build warning in patch 4/11 that for some reason
doesn't appear in my W=1 C=1 build.
https://patchwork.hopto.org/static/nipa/592567/12665209/build_clang/stderr
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All current in-tree uses of dp->priv have been replaced with
ds->tagger_data, which provides for a safer API especially when the
connection isn't the regular 1:1 link between one switch driver and one
tagging protocol driver, but could be either one switch to many taggers,
or many switches to one tagger.
Therefore, we can remove this unused pointer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver messes with the tagging protocol's state when PTP RX
timestamping is enabled/disabled. This is fundamentally necessary
because the tagger needs to know what to do when it receives a PTP
packet. If RX timestamping is enabled, then a metadata follow-up frame
is expected, and this holds the (partial) timestamp. So the tagger plays
hide-and-seek with the network stack until it also gets the metadata
frame, and then presents a single packet, the timestamped PTP packet.
But when RX timestamping isn't enabled, there is no metadata frame
expected, so the hide-and-seek game must be turned off and the packet
must be delivered right away to the network stack.
Considering this, we create a pseudo isolation by devising two tagger
methods callable by the switch: one to get the RX timestamping state,
and one to set it. Since we can't export symbols between the tagger and
the switch driver, these methods are exposed through function pointers.
After this change, the public portion of the sja1105_tagger_data
contains only function pointers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6d709cadfd.
The above change was done to avoid calling symbols exported by the
switch driver from the tagging protocol driver.
With the tagger-owned storage model, we have a new option on our hands,
and that is for the switch driver to provide a data consumer handler in
the form of a function pointer inside the ->connect_tag_protocol()
method. Having a function pointer avoids the problems of the exported
symbols approach.
By creating a handler for metadata frames holding TX timestamps on
SJA1110, we are able to eliminate an skb queue from the tagger data, and
replace it with a simple, and stateless, function pointer. This skb
queue is now handled exclusively by sja1105_ptp.c, which makes the code
easier to follow, as it used to be before the reverted patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, struct sja1105_tagger_data is a part of struct
sja1105_private, and is used by the sja1105 driver to populate dp->priv.
With the movement towards tagger-owned storage, the sja1105 driver
should not be the owner of this memory.
This change implements the connection between the sja1105 switch driver
and its tagging protocol, which means that sja1105_tagger_data no longer
stays in dp->priv but in ds->tagger_data, and that the sja1105 driver
now only populates the sja1105_port_deferred_xmit callback pointer.
The kthread worker is now the responsibility of the tagger.
The sja1105 driver also alters the tagger's state some more, especially
with regard to the PTP RX timestamping state. This will be fixed up a
bit in further changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX timestamp ID is incremented by the SJA1110 PTP timestamping
callback (->port_tx_timestamp) for every packet, when cloning it.
It isn't used by the tagger at all, even though it sits inside the
struct sja1105_tagger_data.
Also, serialization to this structure is currently done through
tagger_data->meta_lock, which is a cheap hack because the meta_lock
isn't used for anything else on SJA1110 (sja1105_rcv_meta_state_machine
isn't called).
This change moves ts_id from sja1105_tagger_data to sja1105_private and
introduces a dedicated spinlock for it, also in sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The design of the sja1105 tagger dp->priv is that each port has a
separate struct sja1105_port, and the sp->data pointer points to a
common struct sja1105_tagger_data.
We have removed all per-port members accessible by the tagger, and now
only struct sja1105_tagger_data remains. Make dp->priv point directly to
this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tagger property is in fact not used at all by the tagger, only by
the switch driver. Therefore it makes sense to be moved to
sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ocelot-8021q driver was converted to deferred xmit as part of
commit 8d5f7954b7 ("net: dsa: felix: break at first CPU port during
init and teardown"), the deferred implementation was deliberately made
subtly different from what sja1105 has.
The implementation differences lied on the following observations:
- There might be a race between these two lines in tag_sja1105.c:
skb_queue_tail(&sp->xmit_queue, skb_get(skb));
kthread_queue_work(sp->xmit_worker, &sp->xmit_work);
and the skb dequeue logic in sja1105_port_deferred_xmit(). For
example, the xmit_work might be already queued, however the work item
has just finished walking through the skb queue. Because we don't
check the return code from kthread_queue_work, we don't do anything if
the work item is already queued.
However, nobody will take that skb and send it, at least until the
next timestampable skb is sent. This creates additional (and
avoidable) TX timestamping latency.
To close that race, what the ocelot-8021q driver does is it doesn't
keep a single work item per port, and a skb timestamping queue, but
rather dynamically allocates a work item per packet.
- It is also unnecessary to have more than one kthread that does the
work. So delete the per-port kthread allocations and replace them with
a single kthread which is global to the switch.
This change brings the two implementations in line by applying those
observations to the sja1105 driver as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is not necessary and complicates the conversion of this driver
to tagger-owned memory. If there is a PTP packet that is sent
concurrently with the port getting disabled, the deferred xmit mechanism
is robust enough to time out when it sees that it hasn't been delivered,
and recovers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix driver makes very light use of dp->priv, and the tagger is
effectively stateless. dp->priv is practically only needed to set up a
callback to perform deferred xmit of PTP and STP packets using the
ocelot-8021q tagging protocol (the main ocelot tagging protocol makes no
use of dp->priv, although this driver sets up dp->priv irrespective of
actual tagging protocol in use).
struct felix_port (what used to be pointed to by dp->priv) is removed
and replaced with a two-sided structure. The public side of this
structure, visible to the switch driver, is ocelot_8021q_tagger_data.
The private side is ocelot_8021q_tagger_private, and the latter
structure physically encapsulates the former. The public half of the
tagger data structure can be accessed through a helper of the same name
(ocelot_8021q_tagger_data) which also sanity-checks the protocol
currently in use by the switch. The public/private split was requested
by Andrew Lunn.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel is working on register access over Ethernet for the qca8k switch
family. This requires the qca8k tagging protocol driver to receive
frames which aren't intended for the network stack, but instead for the
qca8k switch driver itself.
The dp->priv is currently the prevailing method for passing data back
and forth between the tagging protocol driver and the switch driver.
However, this method is riddled with caveats.
The DSA design allows in principle for any switch driver to return any
protocol it desires in ->get_tag_protocol(). The dsa_loop driver can be
modified to do just that. But in the current design, the memory behind
dp->priv has to be allocated by the switch driver, so if the tagging
protocol is paired to an unexpected switch driver, we may end up in NULL
pointer dereferences inside the kernel, or worse (a switch driver may
allocate dp->priv according to the expectations of a different tagger).
The latter possibility is even more plausible considering that DSA
switches can dynamically change tagging protocols in certain cases
(dsa <-> edsa, ocelot <-> ocelot-8021q), and the current design lends
itself to mistakes that are all too easy to make.
This patch proposes that the tagging protocol driver should manage its
own memory, instead of relying on the switch driver to do so.
After analyzing the different in-tree needs, it can be observed that the
required tagger storage is per switch, therefore a ds->tagger_data
pointer is introduced. In principle, per-port storage could also be
introduced, although there is no need for it at the moment. Future
changes will replace the current usage of dp->priv with ds->tagger_data.
We define a "binding" event between the DSA switch tree and the tagging
protocol. During this binding event, the tagging protocol's ->connect()
method is called first, and this may allocate some memory for each
switch of the tree. Then a cross-chip notifier is emitted for the
switches within that tree, and they are given the opportunity to fix up
the tagger's memory (for example, they might set up some function
pointers that represent virtual methods for consuming packets).
Because the memory is owned by the tagger, there exists a ->disconnect()
method for the tagger (which is the place to free the resources), but
there doesn't exist a ->disconnect() method for the switch driver.
This is part of the design. The switch driver should make minimal use of
the public part of the tagger data, and only after type-checking it
using the supplied "proto" argument.
In the code there are in fact two binding events, one is the initial
event in dsa_switch_setup_tag_protocol(). At this stage, the cross chip
notifier chains aren't initialized, so we call each switch's connect()
method by hand. Then there is dsa_tree_bind_tag_proto() during
dsa_tree_change_tag_proto(), and here we have an old protocol and a new
one. We first connect to the new one before disconnecting from the old
one, to simplify error handling a bit and to ensure we remain in a valid
state at all times.
Co-developed-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a typical mv88e6xxx switch tree like this:
CPU
| .----.
.--0--. | .--0--.
| sw0 | | | sw1 |
'-1-2-' | '-1-2-'
'---'
If sw1p{1,2} are added to a bridge that sw0p1 is not a part of, sw0
still needs to add a crosschip PVT entry for the virtual DSA device
assigned to represent the bridge.
Fixes: ce5df6894a ("net: dsa: mv88e6xxx: map virtual bridges with forwarding offload in the PVT")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside netns owned by non-init userns, sysctls about ARP/neighbor is
currently not visible and configurable.
For the attributes these sysctls correspond to, any modifications make
effects on the performance of networking(ARP, especilly) only in the
scope of netns, which does not affect other netns.
Actually, some tools via netlink can modify these attribute. iproute2 is
an example. see as follows:
$ unshare -ur -n
$ cat /proc/sys/net/ipv4/neigh/lo/retrans_time
cat: can't open '/proc/sys/net/ipv4/neigh/lo/retrans_time': No such file
or directory
$ ip ntable show dev lo
inet arp_cache
dev lo
refcnt 1 reachable 19494 base_reachable 30000 retrans 1000
gc_stale 60000 delay_probe 5000 queue 101
app_probes 0 ucast_probes 3 mcast_probes 3
anycast_delay 1000 proxy_delay 800 proxy_queue 64 locktime 1000
inet6 ndisc_cache
dev lo
refcnt 1 reachable 42394 base_reachable 30000 retrans 1000
gc_stale 60000 delay_probe 5000 queue 101
app_probes 0 ucast_probes 3 mcast_probes 3
anycast_delay 1000 proxy_delay 800 proxy_queue 64 locktime 0
$ ip ntable change name arp_cache dev <if> retrans 2000
inet arp_cache
dev lo
refcnt 1 reachable 22917 base_reachable 30000 retrans 2000
gc_stale 60000 delay_probe 5000 queue 101
app_probes 0 ucast_probes 3 mcast_probes 3
anycast_delay 1000 proxy_delay 800 proxy_queue 64 locktime 1000
inet6 ndisc_cache
dev lo
refcnt 1 reachable 35524 base_reachable 30000 retrans 1000
gc_stale 60000 delay_probe 5000 queue 101
app_probes 0 ucast_probes 3 mcast_probes 3
anycast_delay 1000 proxy_delay 800 proxy_queue 64 locktime 0
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Acked-by: Joanne Koong <joannekoong@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clément Léger says:
====================
Add FDMA support on ocelot switch driver
This series adds support for the Frame DMA present on the VSC7514
switch. The FDMA is able to extract and inject packets on the various
ethernet interfaces present on the switch.
====================
Link: https://lore.kernel.org/r/20211209154911.3152830-1-clement.leger@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ethernet frames can be extracted or injected autonomously to or from
the device’s DDR3/DDR3L memory and/or PCIe memory space. Linked list
data structures in memory are used for injecting or extracting Ethernet
frames. The FDMA generates interrupts when frame extraction or
injection is done and when the linked lists need updating.
The FDMA is shared between all the ethernet ports of the switch and
uses a linked list of descriptors (DCB) to inject and extract packets.
Before adding descriptors, the FDMA channels must be stopped. It would
be inefficient to do that each time a descriptor would be added so the
channels are restarted only once they stopped.
Both channels uses ring-like structure to feed the DCBs to the FDMA.
head and tail are never touched by hardware and are completely handled
by the driver. On top of that, page recycling has been added and is
mostly taken from gianfar driver.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Co-developed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit adds support for changing MTU for the ocelot register based
interface. For ocelot, JUMBO frame size can be set up to 25000 bytes
but has been set to 9000 which is a saner value and allows for maximum
gain of performance with FDMA.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support PTP in FDMA, PTP handling code is needed. Since
this is the same as for register-based extraction, export it with
a new ocelot_ptp_rx_timestamp() function.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FDMA will need this code to prepare the injection frame header when
sending SKBs. Move this code into ocelot_ifh_port_set() and add
conditional IFH setting for vlan and rew op if they are not set.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
M Chetan Kumar says:
====================
net: wwan: iosm: improvements
This patch series brings in IOSM driver improvments.
PATCH1: Set tx queue len.
PATCH2: Release data channel if there is no active IP session.
PATCH3: Removes dead code.
PATCH4: Correct open parenthesis alignment.
====================
Link: https://lore.kernel.org/r/20211209143230.3054755-1-m.chetan.kumar@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix checkpatch warning in iosm_ipc_mmio.c
- Alignment should match open parenthesis
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipc_wwan_tx_flowctrl() is declared in iosm_ipc_wwan.h but is
not defined.
Removed the dead code.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If there is no active IP session (interface up & running) then
release the data channel.
Use nr_sessions variable to track current active IP sessions.
If the count drops to 0, then send pipe close ctrl message to
release the data channel.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set wwan net dev tx queue len to DEFAULT_TX_QUEUE_LEN.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 32ecd22ba6 ("net: mscc: ocelot: split register definitions to a
separate file") left out an include for <soc/mscc/ocelot_vcap.h>. It was
missed because the only consumer was ocelot_vsc7514.h, which already
included ocelot_vcap.
Fixes: 32ecd22ba6 ("net: mscc: ocelot: split register definitions to a separate file")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211209074010.1813010-1-colin.foster@in-advantage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The BR-series installation guide from https://driverdownloads.qlogic.com/
mentions the cards support 10Gbase-SR/LR as well as direct attach cables.
The cards only have SFP+ ports, so 10000baseT is not the right mode.
Switch to using more specific link modes added in commit 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes").
Only compile tested.
Signed-off-by: Erik Ekman <erik@kryo.se>
Link: https://lore.kernel.org/r/20211208230022.153496-1-erik@kryo.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves sock_release_ownership() down in include/net/sock.h and
replaces some sk_lock.owned tests with sock_owned_by_user_nocheck().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Link: https://lore.kernel.org/r/20211208062158.54132-1-kuniyu@amazon.co.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrii Nakryiko says:
====================
bpf-next 2021-12-10 v2
We've added 115 non-merge commits during the last 26 day(s) which contain
a total of 182 files changed, 5747 insertions(+), 2564 deletions(-).
The main changes are:
1) Various samples fixes, from Alexander Lobakin.
2) BPF CO-RE support in kernel and light skeleton, from Alexei Starovoitov.
3) A batch of new unified APIs for libbpf, logging improvements, version
querying, etc. Also a batch of old deprecations for old APIs and various
bug fixes, in preparation for libbpf 1.0, from Andrii Nakryiko.
4) BPF documentation reorganization and improvements, from Christoph Hellwig
and Dave Tucker.
5) Support for declarative initialization of BPF_MAP_TYPE_PROG_ARRAY in
libbpf, from Hengqi Chen.
6) Verifier log fixes, from Hou Tao.
7) Runtime-bounded loops support with bpf_loop() helper, from Joanne Koong.
8) Extend branch record capturing to all platforms that support it,
from Kajol Jain.
9) Light skeleton codegen improvements, from Kumar Kartikeya Dwivedi.
10) bpftool doc-generating script improvements, from Quentin Monnet.
11) Two libbpf v0.6 bug fixes, from Shuyi Cheng and Vincent Minet.
12) Deprecation warning fix for perf/bpf_counter, from Song Liu.
13) MAX_TAIL_CALL_CNT unification and MIPS build fix for libbpf,
from Tiezhu Yang.
14) BTF_KING_TYPE_TAG follow-up fixes, from Yonghong Song.
15) Selftests fixes and improvements, from Ilya Leoshkevich, Jean-Philippe
Brucker, Jiri Olsa, Maxim Mikityanskiy, Tirthendu Sarkar, Yucong Sun,
and others.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (115 commits)
libbpf: Add "bool skipped" to struct bpf_map
libbpf: Fix typo in btf__dedup@LIBBPF_0.0.2 definition
bpftool: Switch bpf_object__load_xattr() to bpf_object__load()
selftests/bpf: Remove the only use of deprecated bpf_object__load_xattr()
selftests/bpf: Add test for libbpf's custom log_buf behavior
selftests/bpf: Replace all uses of bpf_load_btf() with bpf_btf_load()
libbpf: Deprecate bpf_object__load_xattr()
libbpf: Add per-program log buffer setter and getter
libbpf: Preserve kernel error code and remove kprobe prog type guessing
libbpf: Improve logging around BPF program loading
libbpf: Allow passing user log setting through bpf_object_open_opts
libbpf: Allow passing preallocated log_buf when loading BTF into kernel
libbpf: Add OPTS-based bpf_btf_load() API
libbpf: Fix bpf_prog_load() log_buf logic for log_level 0
samples/bpf: Remove unneeded variable
bpf: Remove redundant assignment to pointer t
selftests/bpf: Fix a compilation warning
perf/bpf_counter: Use bpf_map_create instead of bpf_create_map
samples: bpf: Fix 'unknown warning group' build warning on Clang
samples: bpf: Fix xdp_sample_user.o linking with Clang
...
====================
Link: https://lore.kernel.org/r/20211210234746.2100561-1-andrii@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix error: "failed to pin map: Bad file descriptor, path:
/sys/fs/bpf/_rodata_str1_1."
In the old kernel, the global data map will not be created, see [0]. So
we should skip the pinning of the global data map to avoid
bpf_object__pin_maps returning error. Therefore, when the map is not
created, we mark “map->skipped" as true and then check during relocation
and during pinning.
Fixes: 16e0c35c6f ("libbpf: Load global data maps lazily on legacy kernels")
Signed-off-by: Shuyi Cheng <chengshuyi@linux.alibaba.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
The btf__dedup_deprecated name was misspelled in the definition of the
compat symbol for btf__dedup. This leads it to be missing from the
shared library.
This fixes it.
Fixes: 957d350a8b ("libbpf: Turn btf_dedup_opts into OPTS-based struct")
Signed-off-by: Vincent Minet <vincent@vincent-minet.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211210063112.80047-1-vincent@vincent-minet.net
Andrii Nakryiko says:
====================
Add new open options and per-program setters to control BTF and program
loading log verboseness and allow providing custom log buffers to capture logs
of interest. Note how custom log_buf and log_level are orthogonal, which
matches previous (alas less customizable) behavior of libbpf, even though it
sort of worked by accident: if someone specified log_level = 1 in
bpf_object__load_xattr(), first attempt to load any BPF program resulted in
wasted bpf() syscall with -EINVAL due to !!log_buf != !!log_level. Then on
retry libbpf would allocated log_buffer and try again, after which prog
loading would succeed and libbpf would print verbose program loading log
through its print callback.
This behavior is now documented and made more efficient, not wasting
unnecessary syscall. But additionally, log_level can be controlled globally on
a per-bpf_object level through bpf_object_open_opts, as well as on
a per-program basis with bpf_program__set_log_buf() and
bpf_program__set_log_level() APIs.
Now that we have a more future-proof way to set log_level, deprecate
bpf_object__load_xattr().
v2->v3:
- added log_buf selftests for bpf_prog_load() and bpf_btf_load();
- fix !log_buf in bpf_prog_load (John);
- fix log_level==0 in bpf_btf_load (thanks selftest!);
v1->v2:
- fix log_level == 0 handling of bpf_prog_load, add as patch #1 (Alexei);
- add comments explaining log_buf_size overflow prevention (Alexei).
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Switch all the uses of to-be-deprecated bpf_object__load_xattr() into
a simple bpf_object__load() calls with optional log_level passed through
open_opts.kernel_log_level, if -d option is specified.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-13-andrii@kernel.org
Switch from bpf_object__load_xattr() to bpf_object__load() and
kernel_log_level in bpf_object_open_opts.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-12-andrii@kernel.org
Add a selftest that validates that per-program and per-object log_buf
overrides work as expected. Also test same logic for low-level
bpf_prog_load() and bpf_btf_load() APIs.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-11-andrii@kernel.org
Deprecate non-extensible bpf_object__load_xattr() in v0.8 ([0]).
With log_level control through bpf_object_open_opts or
bpf_program__set_log_level(), we are finally at the point where
bpf_object__load_xattr() doesn't provide any functionality that can't be
accessed through other (better) ways. The other feature,
target_btf_path, is also controllable through bpf_object_open_opts.
[0] Closes: https://github.com/libbpf/libbpf/issues/289
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-9-andrii@kernel.org
Allow to set user-provided log buffer on a per-program basis ([0]). This
gives great deal of flexibility in terms of which programs are loaded
with logging enabled and where corresponding logs go.
Log buffer set with bpf_program__set_log_buf() overrides kernel_log_buf
and kernel_log_size settings set at bpf_object open time through
bpf_object_open_opts, if any.
Adjust bpf_object_load_prog_instance() logic to not perform own log buf
allocation and load retry if custom log buffer is provided by the user.
[0] Closes: https://github.com/libbpf/libbpf/issues/418
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-8-andrii@kernel.org
Instead of rewriting error code returned by the kernel of prog load with
libbpf-sepcific variants pass through the original error.
There is now also no need to have a backup generic -LIBBPF_ERRNO__LOAD
fallback error as bpf_prog_load() guarantees that errno will be properly
set no matter what.
Also drop a completely outdated and pretty useless BPF_PROG_TYPE_KPROBE
guess logic. It's not necessary and neither it's helpful in modern BPF
applications.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-7-andrii@kernel.org
Add missing "prog '%s': " prefixes in few places and use consistently
markers for beginning and end of program load logs. Here's an example of
log output:
libbpf: prog 'handler': BPF program load failed: Permission denied
libbpf: -- BEGIN PROG LOAD LOG ---
arg#0 reference type('UNKNOWN ') size cannot be determined: -22
; out1 = in1;
0: (18) r1 = 0xffffc9000cdcc000
2: (61) r1 = *(u32 *)(r1 +0)
...
81: (63) *(u32 *)(r4 +0) = r5
R1_w=map_value(id=0,off=16,ks=4,vs=20,imm=0) R4=map_value(id=0,off=400,ks=4,vs=16,imm=0)
invalid access to map value, value_size=16 off=400 size=4
R4 min value is outside of the allowed memory range
processed 63 insns (limit 1000000) max_states_per_insn 0 total_states 0 peak_states 0 mark_read 0
-- END PROG LOAD LOG --
libbpf: failed to load program 'handler'
libbpf: failed to load object 'test_skeleton'
The entire verifier log, including BEGIN and END markers are now always
youtput during a single print callback call. This should make it much
easier to post-process or parse it, if necessary. It's not an explicit
API guarantee, but it can be reasonably expected to stay like that.
Also __bpf_object__open is renamed to bpf_object_open() as it's always
an adventure to find the exact function that implements bpf_object's
open phase, so drop the double underscored and use internal libbpf
naming convention.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-6-andrii@kernel.org
Allow users to provide their own custom log_buf, log_size, and log_level
at bpf_object level through bpf_object_open_opts. This log_buf will be
used during BTF loading. Subsequent patch will use same log_buf during
BPF program loading, unless overriden at per-bpf_program level.
When such custom log_buf is provided, libbpf won't be attempting
retrying loading of BTF to try to provide its own log buffer to capture
kernel's error log output. User is responsible to provide big enough
buffer, otherwise they run a risk of getting -ENOSPC error from the
bpf() syscall.
See also comments in bpf_object_open_opts regarding log_level and
log_buf interactions.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-5-andrii@kernel.org
Add libbpf-internal btf_load_into_kernel() that allows to pass
preallocated log_buf and custom log_level to be passed into kernel
during BPF_BTF_LOAD call. When custom log_buf is provided,
btf_load_into_kernel() won't attempt an retry with automatically
allocated internal temporary buffer to capture BTF validation log.
It's important to note the relation between log_buf and log_level, which
slightly deviates from stricter kernel logic. From kernel's POV, if
log_buf is specified, log_level has to be > 0, and vice versa. While
kernel has good reasons to request such "sanity, this, in practice, is
a bit unconvenient and restrictive for libbpf's high-level bpf_object APIs.
So libbpf will allow to set non-NULL log_buf and log_level == 0. This is
fine and means to attempt to load BTF without logging requested, but if
it failes, retry the load with custom log_buf and log_level 1. Similar
logic will be implemented for program loading. In practice this means
that users can provide custom log buffer just in case error happens, but
not really request slower verbose logging all the time. This is also
consistent with libbpf behavior when custom log_buf is not set: libbpf
first tries to load everything with log_level=0, and only if error
happens allocates internal log buffer and retries with log_level=1.
Also, while at it, make BTF validation log more obvious and follow the log
pattern libbpf is using for dumping BPF verifier log during
BPF_PROG_LOAD. BTF loading resulting in an error will look like this:
libbpf: BTF loading error: -22
libbpf: -- BEGIN BTF LOAD LOG ---
magic: 0xeb9f
version: 1
flags: 0x0
hdr_len: 24
type_off: 0
type_len: 1040
str_off: 1040
str_len: 2063598257
btf_total_size: 1753
Total section length too long
-- END BTF LOAD LOG --
libbpf: Error loading .BTF into kernel: -22. BTF is optional, ignoring.
This makes it much easier to find relevant parts in libbpf log output.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-4-andrii@kernel.org
Similar to previous bpf_prog_load() and bpf_map_create() APIs, add
bpf_btf_load() API which is taking optional OPTS struct. Schedule
bpf_load_btf() for deprecation in v0.8 ([0]).
This makes naming consistent with BPF_BTF_LOAD command, sets up an API
for extensibility in the future, moves options parameters (log-related
fields) into optional options, and also allows to pass log_level
directly.
It also removes log buffer auto-allocation logic from low-level API
(consistent with bpf_prog_load() behavior), but preserves a special
treatment of log_level == 0 with non-NULL log_buf, which matches
low-level bpf_prog_load() and high-level libbpf APIs for BTF and program
loading behaviors.
[0] Closes: https://github.com/libbpf/libbpf/issues/419
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-3-andrii@kernel.org
To unify libbpf APIs behavior w.r.t. log_buf and log_level, fix
bpf_prog_load() to follow the same logic as bpf_btf_load() and
high-level bpf_object__load() API will follow in the subsequent patches:
- if log_level is 0 and non-NULL log_buf is provided by a user, attempt
load operation initially with no log_buf and log_level set;
- if successful, we are done, return new FD;
- on error, retry the load operation with log_level bumped to 1 and
log_buf set; this way verbose logging will be requested only when we
are sure that there is a failure, but will be fast in the
common/expected success case.
Of course, user can still specify log_level > 0 from the very beginning
to force log collection.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211209193840.1248570-2-andrii@kernel.org
'sys/ioctl.h' included in 'mptcp_inq.c' is duplicated.
Reported-by: ZealRobot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Link: https://lore.kernel.org/r/20211210071424.425773-1-ye.guojin@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
net: netns refcount tracking, base series
We have 100+ syzbot reports about netns being dismantled too soon,
still unresolved as of today.
We think a missing get_net() or an extra put_net() is the root cause.
In order to find the bug(s), and be able to spot future ones,
this patch adds CONFIG_NET_NS_REFCNT_TRACKER and new helpers
to precisely pair all put_net() with corresponding get_net().
To use these helpers, each data structure owning a refcount
should also use a "netns_tracker" to pair the get() and put().
Small sections of codes where the get()/put() are in sight
do not need to have a tracker, because they are short lived,
but in theory it is also possible to declare an on-stack tracker.
v2: Include core networking patches only.
====================
Link: https://lore.kernel.org/r/20211210074426.279563-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
