We refactor the tipc_sk_bind() function, so that the lock handling
is handled separately from the logics. We also move some sanity
tests to earlier in the call chain, to the function tipc_bind().
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After migration to the shared interrupt support, the KSZ8031 PHY with
enabled interrupt support was not able to notify about link status
change.
Fixes: 59ca4e58b9 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201127123621.31234-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove obsolete function x25_kill_by_device(). It's not used any more.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have to take the actual link state into account to handle
restart requests/confirms well.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1. DTE interface changes immediately to LAPB_STATE_1 and start sending
SABM(E).
2. DCE interface sends N2-times DM and changes to LAPB_STATE_1
afterwards if there is no response in the meantime.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch allows layer2 (LAPB) to react to netdev events itself and
avoids the detour via layer3 (X.25).
1. Establish layer2 on NETDEV_UP events, if the carrier is already up.
2. Call lapb_disconnect_request() on NETDEV_GOING_DOWN events to signal
the peer that the connection will go down.
(Only when the carrier is up.)
3. When a NETDEV_DOWN event occur, clear all queues, enter state
LAPB_STATE_0 and stop all timers.
4. The NETDEV_CHANGE event makes it possible to handle carrier loss and
detection.
In case of Carrier Loss, clear all queues, enter state LAPB_STATE_0
and stop all timers.
In case of Carrier Detection, we start timer t1 on a DCE interface,
and on a DTE interface we change to state LAPB_STATE_1 and start
sending SABM(E).
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1. Add / remove x25_link_device by NETDEV_REGISTER/UNREGISTER and also
by NETDEV_POST_TYPE_CHANGE/NETDEV_PRE_TYPE_CHANGE.
This change is needed so that the x25_neigh struct for an interface
is already created when it shows up and is kept independently if the
interface goes UP or DOWN.
This is used in an upcomming commit, where x25 params of an neighbour
will get configurable through ioctls.
2. NETDEV_CHANGE event makes it possible to handle carrier loss and
detection. If carrier is lost, clean up everything related to this
neighbour by calling x25_link_terminated().
3. Also call x25_link_terminated() for NETDEV_DOWN events and remove the
call to x25_clear_forward_by_dev() in x25_route_device_down(), as
this is already called by x25_kill_by_neigh() which gets called by
x25_link_terminated().
4. Do nothing for NETDEV_UP and NETDEV_GOING_DOWN events, as these will
be handled in layer 2 (LAPB) and layer3 (X.25) will be informed by
layer2 when layer2 link is established and layer3 link should be
initiated.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel says:
====================
mlxsw: Update adjacency index more efficiently
The device supports an operation that allows the driver to issue one
request to update the adjacency index for all the routes in a given
virtual router (VR) from old index and size to new ones. This is useful
in case the configuration of a certain nexthop group is updated and its
adjacency index changes.
Currently, the driver does not use this operation in an efficient
manner. It iterates over all the routes using the nexthop group and
issues an update request for the VR if it is not the same as the
previous VR.
Instead, this patch set tracks the VRs in which the nexthop group is
used and issues one request for each VR.
Example:
8k IPv6 routes were added in an alternating manner to two VRFs. All the
routes are using the same nexthop object ('nhid 1').
Before:
Performance counter stats for 'ip nexthop replace id 1 via 2001:db8:1::2 dev swp3':
16,385 devlink:devlink_hwmsg
4.255933213 seconds time elapsed
0.000000000 seconds user
0.666923000 seconds sys
Number of EMAD transactions corresponds to number of routes using the
nexthop group.
After:
Performance counter stats for 'ip nexthop replace id 1 via 2001:db8:1::2 dev swp3':
3 devlink:devlink_hwmsg
0.077655094 seconds time elapsed
0.000000000 seconds user
0.076698000 seconds sys
Number of EMAD transactions corresponds to number of VRFs / VRs.
Patch set overview:
Patch #1 is a fix for a bug introduced in previous submission. Detected
by Coverity.
Patches #2 and #3 are preparations.
Patch #4 tracks the VRs a nexthop group is member of.
Patch #5 uses the membership tracking from the previous patch to issue
one update request per each VR.
====================
Link: https://lore.kernel.org/r/20201125193505.1052466-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The device supports an operation that allows the driver to issue one
request to update the adjacency index for all the routes in a given
virtual router (VR) from old index and size to new ones. This is useful
in case the configuration of a certain nexthop group is updated and its
adjacency index changes.
Currently, the driver does not use this operation in an efficient
manner. It iterates over all the routes using the nexthop group and
issues an update request for the VR if it is not the same as the
previous VR.
Instead, use the VR tracking added in the previous patch to update the
adjacency index once for each VR currently using the nexthop group.
Example:
8k IPv6 routes were added in an alternating manner to two VRFs. All the
routes are using the same nexthop object ('nhid 1').
Before:
# perf stat -e devlink:devlink_hwmsg --filter='incoming==0' -- ip nexthop replace id 1 via 2001:db8:1::2 dev swp3
Performance counter stats for 'ip nexthop replace id 1 via 2001:db8:1::2 dev swp3':
16,385 devlink:devlink_hwmsg
4.255933213 seconds time elapsed
0.000000000 seconds user
0.666923000 seconds sys
Number of EMAD transactions corresponds to number of routes using the
nexthop group.
After:
# perf stat -e devlink:devlink_hwmsg --filter='incoming==0' -- ip nexthop replace id 1 via 2001:db8:1::2 dev swp3
Performance counter stats for 'ip nexthop replace id 1 via 2001:db8:1::2 dev swp3':
3 devlink:devlink_hwmsg
0.077655094 seconds time elapsed
0.000000000 seconds user
0.076698000 seconds sys
Number of EMAD transactions corresponds to number of VRFs / VRs.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For each nexthop group, track in which virtual routers (VRs) the group is
used. This is going to be used by the next patch to perform a more
efficient adjacency index update whenever the group's adjacency index
changes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the rare case where the adjacency pointer cannot be updated for a
given virtual router, rollback the operation so that virtual routers
that are already using the new index will use the old one again.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlxsw_sp_adj_index_mass_update_vr() only needs the virtual router's
identifier and protocol, so pass them directly. In a subsequent patch
the caller will not have access to the pointer.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
wenxu says:
====================
net/sched: fix over mtu packet of defrag in
Currently kernel tc subsystem can do conntrack in act_ct. But when several
fragment packets go through the act_ct, function tcf_ct_handle_fragments
will defrag the packets to a big one. But the last action will redirect
mirred to a device which maybe lead the reassembly big packet over the mtu
of target device.
The first patch fix miss init the qdisc_skb_cb->mru
The send one refactor the hanle of xmit in act_mirred and prepare for the
third one
The last one add implict packet fragment support to fix the over mtu for
defrag in act_ct.
====================
Link: https://lore.kernel.org/r/1606276883-6825-1-git-send-email-wenxu@ucloud.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently kernel tc subsystem can do conntrack in cat_ct. But when several
fragment packets go through the act_ct, function tcf_ct_handle_fragments
will defrag the packets to a big one. But the last action will redirect
mirred to a device which maybe lead the reassembly big packet over the mtu
of target device.
This patch add support for a xmit hook to mirred, that gets executed before
xmiting the packet. Then, when act_ct gets loaded, it configs that hook.
The frag xmit hook maybe reused by other modules.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mru in the qdisc_skb_cb should be init as 0. Only defrag packets in the
act_ct will set the value.
Fixes: 038ebb1a71 ("net/sched: act_ct: fix miss set mru for ovs after defrag in act_ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vadim Fedorenko says:
====================
Add CHACHA20-POLY1305 cipher to Kernel TLS
RFC 7905 defines usage of ChaCha20-Poly1305 in TLS connections. This
cipher is widely used nowadays and it's good to have a support for it
in TLS connections in kernel.
====================
Link: https://lore.kernel.org/r/1606231490-653-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new cipher as a variant of standard tls selftests
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RFC 7905 defines special behavior for ChaCha-Poly TLS sessions.
The differences are in the calculation of nonce and the absence
of explicit IV. This behavior is like TLSv1.3 partly.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To provide support for ChaCha-Poly cipher we need to define
specific constants and structures.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Inline functions defined in tls.h have a lot of AES-specific
constants. Remove these constants and change argument to struct
tls_prot_info to have an access to cipher type in later patches
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2020-11-24
This series contains updates to i40e and igbvf drivers.
Marek removes a redundant assignment for i40e.
Stefan Assmann corrects reporting of VF link speed for i40e.
Karen revises a couple of error messages to warnings for igbvf as they
could be misinterpreted as issues when they are not.
v2: Dropped PTP patch as it's being updated.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igbvf: Refactor traces
i40e: report correct VF link speed when link state is set to enable
i40e: remove redundant assignment
====================
Link: https://lore.kernel.org/r/20201124165245.2844118-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Chris Packham says:
====================
net: dsa: mv88e6xxx: serdes link without phy
This small series gets my hardware into a working state. The key points are to
make sure we don't force the link and that we ask the MAC for the link status.
I also have updated my dts to say `phy-mode = "1000base-x";` and `managed =
"in-band-status";`
I've dropped the patch for the 88E6123 as it's a distraction and I lack
hardware to do any proper testing with it. Earlier versions are on the mailing
list if anyone wants to pick it up in the future.
I notice there's a series for mv88e6393x circulating on the netdev mailing
list. As patch #1 is adding a new device specific op either this series will
need updating to cover the mv88e6393x or the mv88e6393x series will need
updating for the new op depenting on which lands first.
====================
Link: https://lore.kernel.org/r/20201124043440.28400-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the underlying read operation failed we would end up writing stale
data to the supplied buffer. This would end up with the last
successfully read value repeating. Fix this by only writing the data
when we know the read was good. This will mean that failed values will
return 0xffff.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MV88E6097 presents the serdes interrupts for ports 8 and 9 via the
Switch Global 2 registers. There is no additional layer of
enablinh/disabling the serdes interrupts like other mv88e6xxx switches.
Even though most of the serdes behaviour is the same as the MV88E6185
that chip does not provide interrupts for serdes events so unlike
earlier commits the functions added here are specific to the MV88E6097.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement serdes_power, serdes_get_lane and serdes_pcs_get_state ops for
the MV88E6097/6095/6185 so that ports 8 & 9 can be supported as serdes
ports and directly connected to other network interfaces or to SFPs
without a PHY.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a port is configured with 'managed = "in-band-status"' switch chips
like the 88E6390 need to propagate the SERDES link state to the MAC
because the link state is not correctly detected. This causes problems
on the 88E6185/88E6097 where the link partner won't see link state
changes because we're forcing the link.
To address this introduce a new device specific op port_sync_link() and
push the logic from mv88e6xxx_mac_link_up() into that. Provide an
implementation for the 88E6185 like devices which doesn't force the
link.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Christian Eggers says:
====================
dt-bindings: net: dsa: microchip: convert KSZ bindings to yaml
These patches are orginally from the series
"net: dsa: microchip: PTP support for KSZ956x"
As the the device tree conversion to yaml is not really related to the
PTP patches and the original series is going to take more time than
I expected, I would like to split this.
Changes (original series -> v1)
--------------------------------
- dts: moved "allOf" below "maintainers"
- dts: use "unevaluatedProperties" instead of "additionalProperties"
- dts: removed "spi-cpha" and "spi-cpol" flags as the hardware is fixed
- ksz8795: setup SPI for mode 3
- ksz9477: dito
====================
Link: https://lore.kernel.org/r/20201120112107.16334-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This should be done in the device driver instead of the device tree.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This should be done in the device driver instead of the device tree.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dsa.yaml device tree binding allows "ethernet-ports" (preferred) and
"ports".
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert the bindings document for Microchip KSZ Series Ethernet switches
from txt to yaml. Removed spi-cpha and spi-cpol flags is this should be
handled by the device driver.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yunsheng Lin says:
====================
Add an assert in napi_consume_skb()
This patch introduces a lockdep_assert_in_softirq() interface and
uses it to assert the case when napi_consume_skb() is not called in
the softirq context.
====================
Link: https://lore.kernel.org/r/1606214969-97849-1-git-send-email-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use napi_consume_skb() to assert the case when it is not called
in a atomic softirq context.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current semantic for napi_consume_skb() is that caller need
to provide non-zero budget when calling from NAPI context, and
breaking this semantic will cause hard to debug problem, because
_kfree_skb_defer() need to run in atomic context in order to push
the skb to the particular cpu' napi_alloc_cache atomically.
So add the lockdep_assert_in_softirq() to assert when the running
context is not in_softirq, in_softirq means softirq is serving or
BH is disabled, which has a ambiguous semantics due to the BH
disabled confusion, so add a comment to emphasize that.
And the softirq context can be interrupted by hard IRQ or NMI
context, lockdep_assert_in_softirq() need to assert about hard
IRQ or NMI context too.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are only used as input arguments to qmi_handle_init() which
accepts const pointers to both qmi_ops and qmi_msg_handler. Make them
const to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201122234031.33432-2-rikard.falkeborn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can enter the main mptcp_recvmsg() loop even when
no subflows are connected. As note by Eric, that would
result in a divide by zero oops on ack generation.
Address the issue by checking the subflow status before
sending the ack.
Additionally protect mptcp_recvmsg() against invocation
with weird socket states.
v1 -> v2:
- removed unneeded inline keyword - Jakub
Reported-and-suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: ea4ca586b1 ("mptcp: refine MPTCP-level ack scheduling")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/5370c0ae03449239e3d1674ddcfb090cf6f20abe.1606253206.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend MRP to support LC mode(link check) for the interconnect port.
This applies only to the interconnect ring.
Opposite to RC mode(ring check) the LC mode is using CFM frames to
detect when the link goes up or down and based on that the userspace
will need to react.
One advantage of the LC mode over RC mode is that there will be fewer
frames in the normal rings. Because RC mode generates InTest on all
ports while LC mode sends CFM frame only on the interconnect port.
All 4 nodes part of the interconnect ring needs to have the same mode.
And it is not possible to have running LC and RC mode at the same time
on a node.
Whenever the MIM starts it needs to detect the status of the other 3
nodes in the interconnect ring so it would send a frame called
InLinkStatus, on which the clients needs to reply with their link
status.
This patch adds InLinkStatus frame type and extends existing rules on
how to forward this frame.
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20201124082525.273820-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently both filter and action flags use same "TCA_" prefix which makes
them hard to distinguish to code and confusing for users. Create aliases
for existing action flags constants with "TCA_ACT_" prefix.
Signed-off-by: Vlad Buslov <vlad@buslov.dev>
Link: https://lore.kernel.org/r/20201124164054.893168-1-vlad@buslov.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On close this timer might be scheduled. mptcp uses sk_reset_timer for
this, so the a reference on the mptcp socket is taken.
This causes a refcount leak which can for example be reproduced
with 'mp_join_server_v4.pkt' from the mptcp-packetdrill repo.
The leak has nothing to do with join requests, v1_mp_capable_bind_no_cs.pkt
works too when replacing the last ack mpcapable to v1 instead of v0.
unreferenced object 0xffff888109bba040 (size 2744):
comm "packetdrill", [..]
backtrace:
[..] sk_prot_alloc.isra.0+0x2b/0xc0
[..] sk_clone_lock+0x2f/0x740
[..] mptcp_sk_clone+0x33/0x1a0
[..] subflow_syn_recv_sock+0x2b1/0x690 [..]
Fixes: e16163b6e2 ("mptcp: refactor shutdown and close")
Cc: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20201124162446.11448-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rtl8211f supports downshift and before commit 5502b218e0
("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
the read-back of register MII_CTRL1000 was used to detect the
negotiated link speed.
The code added in commit d445dff2df ("net: phy: realtek: read
actual speed to detect downshift") is working fine also for this
phy and it's trivial re-using it to restore the downshift
detection on rtl8211f.
Add the phy specific read_status() pointing to the existing
function rtlgen_read_status().
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Link: https://lore.kernel.org/r/478f871a-583d-01f1-9cc5-2eea56d8c2a7@huawei.com
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Link: https://lore.kernel.org/r/20201124230756.887925-1-antonio.borneo@st.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Christian Eggers says:
====================
net: ptp: use common defines for PTP message types in further drivers
This series replaces further driver internal enumeration / uses of magic
numbers with the newly introduced PTP_MSGTYPE_* defines.
====================
Link: https://lore.kernel.org/r/20201124074418.2609-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use recently introduced PTP_MSGTYPE_SYNC and PTP_MSGTYPE_DELAY_REQ
defines instead of a driver internal enumeration.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace use of magic number with recently introduced define.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei says:
====================
net: phy: add support for shared interrupts (part 3)
This patch set aims to actually add support for shared interrupts in
phylib and not only for multi-PHY devices. While we are at it,
streamline the interrupt handling in phylib.
For a bit of context, at the moment, there are multiple phy_driver ops
that deal with this subject:
- .config_intr() - Enable/disable the interrupt line.
- .ack_interrupt() - Should quiesce any interrupts that may have been
fired. It's also used by phylib in conjunction with .config_intr() to
clear any pending interrupts after the line was disabled, and before
it is going to be enabled.
- .did_interrupt() - Intended for multi-PHY devices with a shared IRQ
line and used by phylib to discern which PHY from the package was the
one that actually fired the interrupt.
- .handle_interrupt() - Completely overrides the default interrupt
handling logic from phylib. The PHY driver is responsible for checking
if any interrupt was fired by the respective PHY and choose
accordingly if it's the one that should trigger the link state machine.
From my point of view, the interrupt handling in phylib has become
somewhat confusing with all these callbacks that actually read the same
PHY register - the interrupt status. A more streamlined approach would
be to just move the responsibility to write an interrupt handler to the
driver (as any other device driver does) and make .handle_interrupt()
the only way to deal with interrupts.
Another advantage with this approach would be that phylib would gain
support for shared IRQs between different PHY (not just multi-PHY
devices), something which at the moment would require extending every
PHY driver anyway in order to implement their .did_interrupt() callback
and duplicate the same logic as in .ack_interrupt(). The disadvantage
of making .did_interrupt() mandatory would be that we are slightly
changing the semantics of the phylib API and that would increase
confusion instead of reducing it.
What I am proposing is the following:
- As a first step, make the .ack_interrupt() callback optional so that
we do not break any PHY driver amid the transition.
- Every PHY driver gains a .handle_interrupt() implementation that, for
the most part, would look like below:
irq_status = phy_read(phydev, INTR_STATUS);
if (irq_status < 0) {
phy_error(phydev);
return IRQ_NONE;
}
if (!(irq_status & irq_mask))
return IRQ_NONE;
phy_trigger_machine(phydev);
return IRQ_HANDLED;
- Remove each PHY driver's implementation of the .ack_interrupt() by
actually taking care of quiescing any pending interrupts before
enabling/after disabling the interrupt line.
- Finally, after all drivers have been ported, remove the
.ack_interrupt() and .did_interrupt() callbacks from phy_driver.
This patch set is part 3 (and final) of the entire change set and it
addresses the remaining PHY drivers that have not been migrated
previosly. Also, it finally removed the .did_interrupt() and
.ack_interrupt() callbacks since they are of no use anymore.
I do not have access to most of these PHY's, therefore I Cc-ed the
latest contributors to the individual PHY drivers in order to have
access, hopefully, to more regression testing.
====================
Link: https://lore.kernel.org/r/20201123153817.1616814-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
