The composite gadget will OOPS if the host sends a control request
targetted to an interface of an un-configured composite device. This patch
prevents this.
The OOPS was observed during WHQL USB CV tests. With this patch, the device
STALLs as per requirement.
Failing test case: From host do the following. I used libusb-1.0
1) Set configuration to zero.
libusb_control_transfer(device_handle,
0, /* standard OUT */
0x9, /* setConfiguration */
0, 0, NULL, 0, 0);
2) Query current configuratioan.
libusb_control_transfer(device_handle,
0x80, /* standard IN*/
0x8, /* getConfiguration */
0, 0, data, 1, 0);
3) Send the non-standard ctrl transfer targetted to interface
libusb_control_transfer(device_handle,
0x81, /* standard IN to interface*/
0x6, /* getDescriptor */
0x2300, 0, data, 0x12, 0);
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Cc: stable <stable@kernel.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Robert Lukassen <robert.lukassen@tomtom.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1417) fixes a problem affecting some (or all) nVidia
chipsets. When the computer is shut down, the OHCI controllers
continue to power the USB buses and evidently they drive a Reset
signal out all their ports. This prevents attached devices from going
to low power. Mouse LEDs stay on, for example, which is disconcerting
for users and a drain on laptop batteries.
The fix involves leaving each OHCI controller in the OPERATIONAL state
during system shutdown rather than putting it in the RESET state.
Although this nominally means the controller is running, in fact it's
not doing very much since all the schedules are all disabled. However
there is ongoing DMA to the Host Controller Communications Area, so
the patch also disables the bus-master capability of all PCI USB
controllers after the shutdown routine runs.
The fix is applied only to nVidia-based PCI OHCI controllers, so it
shouldn't cause problems on systems using other hardware. As an added
safety measure, in case the kernel encounters one of these running
controllers during boot, the patch changes quirk_usb_handoff_ohci()
(which runs early on during PCI discovery) to reset the controller
before anything bad can happen.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The protocol code is set 00 in IAD and it's set to 01 in ACM control
interface descriptor in f_acm.c file. Due to this, windows is unable to
install the modem(ACM) driver based on class-subclass-protocol matching.
This patch corrects the protocol code in ACM IAD to the same as in
acm_control_interface_desc protocol code.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compile warning due a possible uninitialized variable
This patch solves the issue initializing the variable
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <damm@opensource.se>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updated Kconfig for langwell otg transceiver driver.
Add ipc driver(INTEL_SCU_IPC) as a dependency. Driver version is
updated too.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "mutex" ftdi->sw_lock is used as a lock and a completion. Convert
it to a real semaphore which allows both.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.
Make ehci_halt a nop if the controller is not in host mode (otherwise it
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt
knows we are a tdi device.
Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset
Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset
PS : now we handle correctly the device -> host transition.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's spelled "Function Filesystem" / "FunctionFS". This patch
fixes some typos (FunctioFS->FunctionFS, Funcion->Function,
funcion->function, redundant "as") in the Kconfig description of
USB_FUNCTIONFS*.
Signed-off-by: Michael Prokop <mika@grml.org>
Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1413) changes g_file_storage to avoid generating a bogus
automatic serial-number string descriptor. If the user doesn't provide
a valid serial number via a module parameter then a warning is logged
and the gadget won't have any serial string descriptor at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
CC: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit f661c6f8c6 adds a check of the pipe type if
CONFIG_USB_DEBUG is enabled, but it doesn't output anything if this scenario
occurs.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The same expression is tested twice and the result is the same each time.
Instead test for use_dma_ppb as in the test above.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@expression@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the configuration structure.
This fixes many section mismatches reported by modpost.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: updated for -next]
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the composite driver structure.
This fixes many section mismatches reported by modpost.
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To accomplish this the function to register a gadget driver takes the bind
function as a second argument. To make things clearer rename the function
to resemble platform_driver_probe.
This fixes many section mismatches like
WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in
reference from the variable printer_driver to the function
.init.text:printer_bind()
The variable printer_driver references
the function __init printer_bind()
All callers are fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: added dbgp]
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts a commit which proposed an invalid solution
for a section mismatch. Next 3 commits will fix it correctly.
Conflicts:
drivers/usb/gadget/mass_storage.c
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes some of the string registration from the
Multifunction Composite Gadget as composite layer can handle
the iManufacturer and iProduct for us.
This also adds the "needs_serial" so that composite layer will
issue a warning if user space fails to provide the iSerialNumber
module parameter.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes string registration from the Mass Storage
Gadget. With recent changes to the composite framework, all
that we need is handled by the composite layer. This means
composite registers a string ID for manufacturer and product.
This also adds the "needs_serial" so that composite layer will
issue a warning if user space fails to provide the iSerialNumber
module parameter.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The iManufatcurer, iProduct and iSerialNumber composite module
parameters were only used when the gadget driver registers
strings for manufacturer, product and serial number. If the
gadget never bothered to set corresponding fields in USB device
descriptors those module parameters are ignored.
This commit makes the parameters work even if the strings ID
have not been assigned. It also changes the way IDs are
overridden -- what IDs are overridden is now saved in
usb_composite_dev structure -- which makes it unnecessary to
modify the string tables the way previous code did.
The commit also adds a iProduct and iManufatcurer fields to the
usb_composite_device structure. If they are set, appropriate
strings are reserved and added to device descriptor. This makes
it unnecessary for gadget drivers to maintain code for setting
those. If iProduct is not set it defaults to
usb_composite_device::name; if iManufatcurer is not set
a default "<system> <release> with <gadget-name>" is used.
The last thing is that if needs_serial field of
usb_composite_device is set and user failed to provided
iSerialNumber parameter a warning is issued.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes some of the string registration from the
FunctionFS Gadget as composite layer can handle the
iManufacturer and iProduct for us.
It also removes some of the module parameters which were
redundant as well as changes the name of others to better much
the module parameter of the composite layer.
Other then that, it also fixes formatting of multiline comments
to match the coding style.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The nofua parameter (optionally ignore SCSI WRITE FUA) was added
to the File Storage Gadget some time ago. This patch adds the
same functionality to the Mass Storage Function.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The dev_attr_nofua file was created during fsg_bind() but
was never removed. Made it a bit more symmetrical and added
code to remove the file in fsg_unbind().
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the vendor and product ID the gadget uses
by replacing the temporary IDs that were used during
development (which should never get into mainline) with
proper IDs.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the vendor and product ID the gadget uses
by replacing the temporary IDs that were used during
development (which should never get into mainline) with
proper IDs.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Found while debugging a USB problem and trying to find the mentioned function.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new driver to access the SAM-BA boot application of Atmel AT91SAM
devices.
The SAM-BA firmware cannot handle merged write requests so we cannot use
the generic write implementation (which uses the port write fifo).
Tested with the SAM-BA 2.10 tools and an Atmel at91sam9260-ek.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
len is always greater than or equal to zero here. First of all, it's
type is unsigned and also we only assign it numbers which are greater
than or equal to zero.
Removing the check lets us pull everything in an indent level.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Stephane duverger <stephane.duverger@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SRAM Memory handling for USB client function
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remote wakeup support in client driver. Made non-debug only this time.
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PHY low power mode setting with a static function
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Code cleanup by using standard debugging API's and USB inline functions
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for the USB transceiver driver in the Langwell chipset used
on the Intel MID platforms. It folds up the original patch set which includes
basic support for the device, PHY low power mode (Please notice that there is
a limitation, after we drive VBus down, 2ms delay is required from SCU FW to
sync up OTGSC register with USBCFG register), software timers (the hardware
timers do not work in low power mode), HNP, SRP.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1429) updates the Kconfig help text for
CONFIG_USB_SUSPEND. The power/level file is now deprecated; we should
tell people to use power/control instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 46034dca51 (USB: musb_gadget_ep0: stop
abusing musb_gadget_set_halt()) forgot to restart a queued request after
clearing the endpoint halt feature. This results in a couple of USB resets
while enumerating the file-backed storage gadget due to CSW packet not being
sent for the MODE SENSE(10) command.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the issue which was observed while transfering
a large file ( > 20MB) over USB (OMAP MUSB controller acts as USB host)
to an attached USB thumb drive.
It was found that CDB field of CBW packet was set to 0x0. This was
due to missing a barrier before DMA engine starts transfer.
This buffer is allocated using dma_alloc_coherent which gives
non-cacheble but bufferable memory and hence needed a write
memory barrier to flush the write buffer.
More info on this thread is here:
http://www.spinics.net/lists/linux-omap/msg33987.html
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space
of request buffer, so fix it.
Also set max_len of cppi dma channel as max size of
int type, so make musb dma handling happier.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Complete the current request only if the data transfer is over.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space of request buffer,
so fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one bugs of OUT transfer in double buffer case:
-the current code only enable autoclear for dma mode 1, and not
for dma mode 0
Without this patch, test #5 of usbtest can't be passed if we
configure musb as g_zero and use fifo mode 3 to enable double
buffer mode.
With this patch and the following patch(fix dma length),
on my beagle B5, test#5(queued bulk out) may go beyond
18Mbyte/s(seems dma mode 0 is quicker in double buffer case)
if musb is configured as g_zero and fifo mode 3 is taken, follows
the test command:
#./testusb -D DEV_NAME -c 1024 -t 5 -s 32768 -g 8 [1]
Also I have tested this patch can't make g_ether broken.
[1],source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one infinite hang of bulk IN transfer in double buffer
case, the hang can be observed easily by test #6 of usbtest if musb is
configured as g_zero and fifo mode 3 is taken to enable double fifo.
In fact, the patch only removes the check for non-empty fifo before
loading data from new request into fifo since the check is not correct:
-in double buffer case, fifo may accommodate more than one packet,
even though it has contained one packet already and is non-empty
-since last DMA is completed before calling musb_g_tx, it is sure
that fifo may accommodate at least one packet
Without applying the patch, new requst enqueued from .complte may not
have a chance to be loaded into fifo, then will never be completed and
cause infinite hangs.
With the patch, on my beagle B5, test#6(queued bulk in) can be passed and
test result may go beyond 33Mbyte/s if musb is configured as g_zero and
fifo mode 3 is taken, follows the test command:
#testusb -D DEV_NAME -c 1024 -t 6 -s 32768 -g 8 [1]
[1],
-source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent changes in the usbhid layer exposed a bug in usbcore. If
CONFIG_USB_DYNAMIC_MINORS is enabled then an interface may be assigned
a minor number of 0. However interfaces that aren't registered as USB
class devices also have their minor number set to 0, during
initialization. As a result usb_find_interface() may return the
wrong interface, leading to a crash.
This patch (as1418) fixes the problem by initializing every
interface's minor number to -1. It also cleans up the
usb_register_dev() function, which besides being somewhat awkwardly
written, does not unwind completely on all its error paths.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Philip J. Turmel <philip@turmel.org>
Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Matthias Bayer <jackdachef@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TIOCGICOUNT device ioctl in both mos7720.c and mos7840.c allows
unprivileged users to read uninitialized stack memory, because the
"reserved" member of the serial_icounter_struct struct declared on the
stack is not altered or zeroed before being copied back to the user.
This patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 461c317705eca5cac09a360f488715927fd0a927(into 2.6.36-v3)
is put forward to power down phy if no usb cable is connected,
but does introduce the two issues below:
1), phy is not into work state if usb cable is connected
with PC during poweron, so musb device mode is not usable
in such case, follows the reasons:
-twl4030_phy_resume is not called, so
regulators are not enabled
i2c access are not enabled
usb mode not configurated
2), The kernel warings[1] of regulators 'unbalanced disables'
is caused if poweron without usb cable connected
with PC or b-device.
This patch fixes the two issues above:
-power down phy only if no usb cable is connected with PC
and b-device
-do phy initialization(via __twl4030_phy_resume) if usb cable
is connected with PC(vbus event) or another b-device(ID event) in
twl4030_usb_probe.
This patch also doesn't put VUSB3V1 LDO into active mode in
twl4030_usb_ldo_init until VBUS/ID change detected, so we can
save more power consumption than before.
This patch is verified OK on Beagle board either connected with
usb cable or not when poweron.
[1]. warnings of 'unbalanced disables' of regulators.
[root@OMAP3EVM /]# dmesg
------------[ cut here ]------------
WARNING: at drivers/regulator/core.c:1357 _regulator_disable+0x38/0x128()
unbalanced disables for VUSB1V8
Modules linked in:
Backtrace:
[<c0030c48>] (dump_backtrace+0x0/0x110) from [<c034f5a8>] (dump_stack+0x18/0x1c)
r7:c78179d8 r6:c01ed6b8 r5:c0410822 r4:0000054d
[<c034f590>] (dump_stack+0x0/0x1c) from [<c0057da8>] (warn_slowpath_common+0x54/0x6c)
[<c0057d54>] (warn_slowpath_common+0x0/0x6c) from [<c0057e64>] (warn_slowpath_fmt+0x38/0x40)
r9:00000000 r8:00000000 r7:c78e6608 r6:00000000 r5:fffffffb
r4:c78e6c00
[<c0057e2c>] (warn_slowpath_fmt+0x0/0x40) from [<c01ed6b8>] (_regulator_disable+0x38/0x128)
r3:c0410e53 r2:c0410ad5
[<c01ed680>] (_regulator_disable+0x0/0x128) from [<c01ed87c>] (regulator_disable+0x24/0x38)
r7:c78e6608 r6:00000000 r5:c78e6c40 r4:c78e6c00
[<c01ed858>] (regulator_disable+0x0/0x38) from [<c02382dc>] (twl4030_phy_power+0x15c/0x17c)
r5:c78595c0 r4:00000000
[<c0238180>] (twl4030_phy_power+0x0/0x17c) from [<c023831c>] (twl4030_phy_suspend+0x20/0x2c)
r6:00000000 r5:c78595c0 r4:c78595c0
[<c02382fc>] (twl4030_phy_suspend+0x0/0x2c) from [<c0238638>] (twl4030_usb_irq+0x11c/0x16c)
r5:c78595c0 r4:00000040
[<c023851c>] (twl4030_usb_irq+0x0/0x16c) from [<c034ec18>] (twl4030_usb_probe+0x2c4/0x32c)
r6:00000000 r5:00000000 r4:c78595c0
[<c034e954>] (twl4030_usb_probe+0x0/0x32c) from [<c02152a0>] (platform_drv_probe+0x20/0x24)
r7:00000000 r6:c047d49c r5:c78e6608 r4:c047d49c
[<c0215280>] (platform_drv_probe+0x0/0x24) from [<c0214244>] (driver_probe_device+0xd0/0x190)
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c02143d4>] (__device_attach+0x44/0x48)
r7:00000000 r6:c78e6608 r5:c78e6608 r4:c047d49c
[<c0214390>] (__device_attach+0x0/0x48) from [<c0213694>] (bus_for_each_drv+0x50/0x90)
r5:c0214390 r4:00000000
[<c0213644>] (bus_for_each_drv+0x0/0x90) from [<c0214474>] (device_attach+0x70/0x94)
r6:c78e663c r5:c78e6608 r4:c78e6608
[<c0214404>] (device_attach+0x0/0x94) from [<c02134fc>] (bus_probe_device+0x2c/0x48)
r7:00000000 r6:00000002 r5:c78e6608 r4:c78e6600
[<c02134d0>] (bus_probe_device+0x0/0x48) from [<c0211e48>] (device_add+0x340/0x4b4)
[<c0211b08>] (device_add+0x0/0x4b4) from [<c021597c>] (platform_device_add+0x110/0x16c)
[<c021586c>] (platform_device_add+0x0/0x16c) from [<c0220cb0>] (add_numbered_child+0xd8/0x118)
r7:00000000 r6:c045f15c r5:c78e6600 r4:00000000
[<c0220bd8>] (add_numbered_child+0x0/0x118) from [<c001c618>] (twl_probe+0x3a4/0x72c)
[<c001c274>] (twl_probe+0x0/0x72c) from [<c02601ac>] (i2c_device_probe+0x7c/0xa4)
[<c0260130>] (i2c_device_probe+0x0/0xa4) from [<c0214244>] (driver_probe_device+0xd0/0x190)
r5:c7856e20 r4:c047c860
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c02143d4>] (__device_attach+0x44/0x48)
r7:c7856e04 r6:c7856e20 r5:c7856e20 r4:c047c860
[<c0214390>] (__device_attach+0x0/0x48) from [<c0213694>] (bus_for_each_drv+0x50/0x90)
r5:c0214390 r4:00000000
[<c0213644>] (bus_for_each_drv+0x0/0x90) from [<c0214474>] (device_attach+0x70/0x94)
r6:c7856e54 r5:c7856e20 r4:c7856e20
[<c0214404>] (device_attach+0x0/0x94) from [<c02134fc>] (bus_probe_device+0x2c/0x48)
r7:c7856e04 r6:c78fd048 r5:c7856e20 r4:c7856e20
[<c02134d0>] (bus_probe_device+0x0/0x48) from [<c0211e48>] (device_add+0x340/0x4b4)
[<c0211b08>] (device_add+0x0/0x4b4) from [<c0211fd8>] (device_register+0x1c/0x20)
[<c0211fbc>] (device_register+0x0/0x20) from [<c0260aa8>] (i2c_new_device+0xec/0x150)
r5:c7856e00 r4:c7856e20
[<c02609bc>] (i2c_new_device+0x0/0x150) from [<c0260dc0>] (i2c_register_adapter+0xa0/0x1c4)
r7:00000000 r6:c78fd078 r5:c78fd048 r4:c781d5c0
[<c0260d20>] (i2c_register_adapter+0x0/0x1c4) from [<c0260f80>] (i2c_add_numbered_adapter+0x9c/0xb4)
r7:00000a28 r6:c04600a8 r5:c78fd048 r4:00000000
[<c0260ee4>] (i2c_add_numbered_adapter+0x0/0xb4) from [<c034efa4>] (omap_i2c_probe+0x324/0x3e8)
r5:00000000 r4:c78fd000
[<c034ec80>] (omap_i2c_probe+0x0/0x3e8) from [<c02152a0>] (platform_drv_probe+0x20/0x24)
[<c0215280>] (platform_drv_probe+0x0/0x24) from [<c0214244>] (driver_probe_device+0xd0/0x190)
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c021436c>] (__driver_attach+0x68/0x8c)
r7:c78b2140 r6:c047e214 r5:c04600e4 r4:c04600b0
[<c0214304>] (__driver_attach+0x0/0x8c) from [<c021399c>] (bus_for_each_dev+0x50/0x84)
r7:c78b2140 r6:c047e214 r5:c0214304 r4:00000000
[<c021394c>] (bus_for_each_dev+0x0/0x84) from [<c0214068>] (driver_attach+0x20/0x28)
r6:c047e214 r5:c047e214 r4:c00270d0
[<c0214048>] (driver_attach+0x0/0x28) from [<c0213274>] (bus_add_driver+0xa8/0x228)
[<c02131cc>] (bus_add_driver+0x0/0x228) from [<c02146a4>] (driver_register+0xb0/0x13c)
[<c02145f4>] (driver_register+0x0/0x13c) from [<c0215744>] (platform_driver_register+0x4c/0x60)
r9:00000000 r8:c001f688 r7:00000013 r6:c005b6fc r5:c00083dc
r4:c00270d0
[<c02156f8>] (platform_driver_register+0x0/0x60) from [<c001f69c>] (omap_i2c_init_driver+0x14/0x1c)
[<c001f688>] (omap_i2c_init_driver+0x0/0x1c) from [<c002c460>] (do_one_initcall+0xd0/0x1a4)
[<c002c390>] (do_one_initcall+0x0/0x1a4) from [<c0008478>] (kernel_init+0x9c/0x154)
[<c00083dc>] (kernel_init+0x0/0x154) from [<c005b6fc>] (do_exit+0x0/0x688)
r5:c00083dc r4:00000000
---[ end trace 1b75b31a2719ed1d ]---
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have to do so due to HW limitation.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
seq_files use the private_data field of a file struct for storing a seq_file structure,
data should be stored in seq_file's own private field (e.g. file->private_data->private)
Otherwise seq_release() will free the private data when the file is closed.
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
