If the device state GPIO is not connected to the host then disable the
INH output from the TCAN device per section 8.3.5 of the data sheet.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's a good idea to reset a ip-block/spi device before using it, this
patch will reset the device.
And a generic reset function if needed elsewhere.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The tcan4x5x_parse_config() function now performs action on the device
either reading or writing and a reset. If the devive has a switchable
power supppy (i.e. regulator is managed) it needs to be turned on.
So turn on the regulator if available. If the parsing fails, turn off
the regulator.
Fixes: 2de4973569 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The m_can tries to detect if Non ISO Operation is available while in
standby mode, this function results in the following error:
| tcan4x5x spi2.0 (unnamed net_device) (uninitialized): Failed to init module
| tcan4x5x spi2.0: m_can device registered (irq=84, version=32)
| tcan4x5x spi2.0 can2: TCAN4X5X successfully initialized.
When the tcan device comes out of reset it goes in standby mode. The
m_can driver tries to access the control register but fails due to the
device being in standby mode.
So this patch will put the tcan device in normal mode before the m_can
driver does the initialization.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull networking fixes from David Miller:
1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.
2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.
3) Fix precision tracking for unbound scalars in bpf verifier, from
Daniel Borkmann.
4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
Messina.
5) Do not perform a neigh confirmation during a pmtu update over a
tunnel, from Hangbin Liu.
6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.
7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.
8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
Geert Uytterhoeven
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
net/sched: add delete_empty() to filters and use it in cls_flower
tcp: Fix highest_sack and highest_sack_seq
ptp: fix the race between the release of ptp_clock and cdev
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
net: dsa: sja1105: Really make the PTP command read-write
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
cxgb4/cxgb4vf: fix flow control display for auto negotiation
mlxsw: spectrum: Use dedicated policer for VRRP packets
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
net_sched: sch_fq: properly set sk->sk_pacing_status
bnx2x: Fix accounting of vlan resources among the PFs
bnx2x: Use appropriate define for vlan credit
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
net: phy: aquantia: add suspend / resume ops for AQR105
dpaa_eth: fix DMA mapping leak
...
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
This reverts commit 275c44aa19.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes: 275c44aa19 ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()")
Fixes: 6676d5e416 ("net: sched: set dedicated tcf_walker flag when tp is empty")
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From commit 50895b9de1 ("tcp: highest_sack fix"), the logic about
setting tp->highest_sack to the head of the send queue was removed.
Of course the logic is error prone, but it is logical. Before we
remove the pointer to the highest sack skb and use the seq instead,
we need to set tp->highest_sack to NULL when there is no skb after
the last sack, and then replace NULL with the real skb when new skb
inserted into the rtx queue, because the NULL means the highest sack
seq is tp->snd_nxt. If tp->highest_sack is NULL and new data sent,
the next ACK with sack option will increase tp->reordering unexpectedly.
This patch sets tp->highest_sack to the tail of the rtx queue if
it's NULL and new data is sent. The patch keeps the rule that the
highest_sack can only be maintained by sack processing, except for
this only case.
Fixes: 50895b9de1 ("tcp: highest_sack fix")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
ts# cat openptp0.c
int main() { ... fp = fopen("/dev/ptp0", "r"); ... sleep(10); }
ts# uname -r
5.5.0-rc3-46cf053e
ts# cat /proc/cmdline
... slub_debug=FZP
ts# modprobe ptp_kvm
ts# ./openptp0 &
[1] 670
opened /dev/ptp0, sleeping 10s...
ts# rmmod ptp_kvm
ts# ls /dev/ptp*
ls: cannot access '/dev/ptp*': No such file or directory
ts# ...woken up
[ 48.010809] general protection fault: 0000 [#1] SMP
[ 48.012502] CPU: 6 PID: 658 Comm: openptp0 Not tainted 5.5.0-rc3-46cf053e #25
[ 48.014624] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 48.016270] RIP: 0010:module_put.part.0+0x7/0x80
[ 48.017939] RSP: 0018:ffffb3850073be00 EFLAGS: 00010202
[ 48.018339] RAX: 000000006b6b6b6b RBX: 6b6b6b6b6b6b6b6b RCX: ffff89a476c00ad0
[ 48.018936] RDX: fffff65a08d3ea08 RSI: 0000000000000247 RDI: 6b6b6b6b6b6b6b6b
[ 48.019470] ... ^^^ a slub poison
[ 48.023854] Call Trace:
[ 48.024050] __fput+0x21f/0x240
[ 48.024288] task_work_run+0x79/0x90
[ 48.024555] do_exit+0x2af/0xab0
[ 48.024799] ? vfs_write+0x16a/0x190
[ 48.025082] do_group_exit+0x35/0x90
[ 48.025387] __x64_sys_exit_group+0xf/0x10
[ 48.025737] do_syscall_64+0x3d/0x130
[ 48.026056] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.026479] RIP: 0033:0x7f53b12082f6
[ 48.026792] ...
[ 48.030945] Modules linked in: ptp i6300esb watchdog [last unloaded: ptp_kvm]
[ 48.045001] Fixing recursive fault but reboot is needed!
This happens in:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa24 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7f ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u
Analyzed-by: Stephen Johnston <sjohnsto@redhat.com>
Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 86db36a347 ("net: dsa: sja1105: Implement state machine
for TAS with PTP clock source"), this paragraph is no longer true. So
remove it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes: 86db36a347 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes: 41603d78b3 ("net: dsa: sja1105: Make the PTP command read-write")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
[1] https://standards.ieee.org/standard/802_3-2005.html
Fixes: c3168cabe1 ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Couple of fixes
This patch set contains two fixes for mlxsw. Please consider both for
stable.
Patch #1 from Amit fixes a wrong check during MAC validation when
creating router interfaces (RIFs). Given a particular order of
configuration this can result in the driver refusing to create new RIFs.
Patch #2 fixes a wrong trap configuration in which VRRP packets and
routing exceptions were policed by the same policer towards the CPU. In
certain situations this can prevent VRRP packets from reaching the CPU.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes: 11566d34f8 ("mlxsw: spectrum: Add VRRP traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.
Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.
Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:
Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.
Fix this by skipping loopback RIFs during MAC validation.
Fixes: 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One important fix for RISC-V:
- Redirect any incoming syscall with an ID less than -1 to
sys_ni_syscall, rather than allowing them to fall through into the
syscall handler.
and two minor build fixes:
- Export __asm_copy_{from,to}_user() from where they are defined.
This fixes a build error triggered by some randconfigs.
- Export flush_icache_all(). I'd resisted this before, since
historically we didn't want modules to be able to flush the I$
directly; but apparently everyone else is doing it now.
-----BEGIN PGP SIGNATURE-----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=y3/O
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"One important fix for RISC-V:
- Redirect any incoming syscall with an ID less than -1 to
sys_ni_syscall, rather than allowing them to fall through into the
syscall handler.
and two minor build fixes:
- Export __asm_copy_{from,to}_user() from where they are defined.
This fixes a build error triggered by some randconfigs.
- Export flush_icache_all(). I'd resisted this before, since
historically we didn't want modules to be able to flush the I$
directly; but apparently everyone else is doing it now"
* tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: export flush_icache_all to modules
riscv: reject invalid syscalls below -1
riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
-----BEGIN PGP SIGNATURE-----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=AIbz
-----END PGP SIGNATURE-----
Merge tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull /proc/locks formatting fix from Jeff Layton:
"This is a trivial fix for a _very_ long standing bug in /proc/locks
formatting. Ordinarily, I'd wait for the merge window for something
like this, but it is making it difficult to validate some overlayfs
fixes.
I've also gone ahead and marked this for stable"
* tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: print unsigned ino in /proc/locks
-----BEGIN PGP SIGNATURE-----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=cuQx
-----END PGP SIGNATURE-----
Merge tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"One performance fix for large directory searches, and one minor style
cleanup noticed by Clang"
* tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Optimize readdir on reparse points
cifs: Adjust indentation in smb2_open_file
An ino is unsigned, so display it as such in /proc/locks.
Cc: stable@vger.kernel.org
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
This is needed by LKDTM (crash dump test module), it calls
flush_icache_range(), which on RISC-V turns into flush_icache_all(). On
other architectures, the actual implementation is exported, so follow
that precedence and export it here too.
Fixes build of CONFIG_LKDTM that fails with:
ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined!
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops
with "Unable to handle kernel paging request at virtual address" message. This
happens when enosys stressor starts testing random non-valid syscalls.
I forgot to redirect any syscall below -1 to sys_ni_syscall.
With the patch kernel oops messages are gone while running stress-ng enosys
stressor.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Fixes: 5340627e3f ("riscv: add support for SECCOMP and SECCOMP_FILTER")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When support for !MMU was added, the declaration of
__asm_copy_to_user() & __asm_copy_from_user() were #ifdefed
out hence their EXPORT_SYMBOL() give an error message like:
.../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here
.../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here
Since these symbols are not defined with !MMU it's wrong to export them.
Same for __clear_user() (even though this one is also declared in
include/asm-generic/uaccess.h and thus doesn't give an error message).
Fix this by doing the EXPORT_SYMBOL() directly where these symbols
are defined: inside lib/uaccess.S itself.
Fixes: 6bd33e1ece ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Four fixes and one spelling update, all in drivers: 2 in lpfc and the
rest in mp3sas, cxgbi and target.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXgaIWSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishb2SAP45hS5T
owI8lIt+jMBnYG3k/66EleVdqMOcvtm9ewDN2gD/eW1LBz6uPzPn07gLB3V4TTTZ
rI8lfohhWJwRAHjvL8A=
=nxXW
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes and one spelling update, all in drivers: two in lpfc and
the rest in mp3sas, cxgbi and target"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target/iblock: Fix protection error with blocks greater than 512B
scsi: libcxgbi: fix NULL pointer dereference in cxgbi_device_destroy()
scsi: lpfc: fix spelling mistakes of asynchronous
scsi: lpfc: fix build failure with DEBUGFS disabled
scsi: mpt3sas: Fix double free in attach error handling
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for
the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate
can be adjusted at runtime.
So far we have been running MPLL2 with ~250MHz (and the internal
m250_div with value 1), which worked enough that we could transfer data
with an TX delay of 4ns. Unfortunately there is high packet loss with
an RGMII PHY when transferring data (receiving data works fine though).
Odroid-C1's u-boot is running with a TX delay of only 2ns as well as
the internal m250_div set to 2 - no lost (TX) packets can be observed
with that setting in u-boot.
Manual testing has shown that the TX packet loss goes away when using
the following settings in Linux (the vendor kernel uses the same
settings):
- MPLL2 clock set to ~500MHz
- m250_div set to 2
- TX delay set to 2ns on the MAC side
Update the m250_div divider settings to only accept dividers greater or
equal 2 to fix the TX delay generated by the MAC.
iperf3 results before the change:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender
[ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver
iperf3 results after the change (including an updated TX delay of 2ns):
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver
Fixes: 4f6a71b84e ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no skb_pull performed when a mirred action is set at egress of a
mac device, with a target device/action that expects skb->data to point
at the network header.
As a result, either the target device is errornously given an skb with
data pointing to the mac (egress case), or the net stack receives the
skb with data pointing to the mac (ingress case).
E.g:
# tc qdisc add dev eth9 root handle 1: prio
# tc filter add dev eth9 parent 1: prio 9 protocol ip handle 9 basic \
action mirred egress redirect dev tun0
(tun0 is a tun device. result: tun0 errornously gets the eth header
instead of the iph)
Revise the push/pull logic of tcf_mirred_act() to not rely on the
skb_at_tc_ingress() vs tcf_mirred_act_wants_ingress() comparison, as it
does not cover all "pull" cases.
Instead, calculate whether the required action on the target device
requires the data to point at the network header, and compare this to
whether skb->data points to network header - and make the push/pull
adjustments as necessary.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Shmulik Ladkani <sladkani@proofpoint.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i915:
- power management rc6 fix
- framebuffer tracking fix
- display power management ratelimit fix
-----BEGIN PGP SIGNATURE-----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=pliy
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Post-xmas food coma recovery fixes. Only three fixes for i915 since I
expect most people are holidaying.
i915:
- power management rc6 fix
- framebuffer tracking fix
- display power management ratelimit fix"
* tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Hold reference to intel_frontbuffer as we track activity
drm/i915/gt: Ratelimit display power w/a
drm/i915/pmu: Ensure monotonic rc6
This Kselftest update for Linux 5.5-rc4 consists of:
-- rseq build failures fixes related to glibc 2.30 compatibility
from Mathieu Desnoyers
-- Kunit fixes and cleanups from SeongJae Park
-- Fixes to filesystems/epoll, firmware, and livepatch build failures
and skip handling.
-----BEGIN PGP SIGNATURE-----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=ZztB
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- rseq build failures fixes related to glibc 2.30 compatibility from
Mathieu Desnoyers
- Kunit fixes and cleanups from SeongJae Park
- Fixes to filesystems/epoll, firmware, and livepatch build failures
and skip handling.
* tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
rseq/selftests: Clarify rseq_prepare_unload() helper requirements
rseq/selftests: Fix: Namespace gettid() for compatibility with glibc 2.30
rseq/selftests: Turn off timeout setting
kunit/kunit_tool_test: Test '--build_dir' option run
kunit: Rename 'kunitconfig' to '.kunitconfig'
kunit: Place 'test.log' under the 'build_dir'
kunit: Create default config in '--build_dir'
kunit: Remove duplicated defconfig creation
docs/kunit/start: Use in-tree 'kunit_defconfig'
selftests: livepatch: Fix it to do root uid check and skip
selftests: firmware: Fix it to do root uid check and skip
selftests: filesystems/epoll: fix build error
Fix compile test of the Tegra devfreq driver (Arnd Bergmann)
and remove redundant Kconfig dependencies from multiple devfreq
drivers (Leonard Crestez).
-----BEGIN PGP SIGNATURE-----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=EFpO
-----END PGP SIGNATURE-----
Merge tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and
remove redundant Kconfig dependencies from multiple devfreq drivers
(Leonard Crestez)"
* tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAl4E+aYQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgprKmEAC6tcPlb2BB+7fOuj44uAdE+RInqMxbfD3w
Tj9KpF47e02DUvBTtwDJDHJ9QT4PlJhd66M1xrp3IMUV13PKQt9OFfc6TH38Jz/9
mhHDGNj1s+GVLRH22PQtFjyMgzHA6+UF4NxHLDJ62c2CtrCVswFRUiWrSR8LgvDp
EkVELGEpi080ffton9nhyy3ylOCcpCu1xX1mOCg5EhcqzFQnZMlFaj9PDFrNhQzT
e8fdl/nGoKtxZ/x6V8Oso02r/K1XievV4dfrAtOZg4jiqp/3G2eiqoGGcYnShSDU
qulKLGsuHK51Lay8AGEaw3haeMn1PKCNe+xv0uCubHdf2iMyBdpjCLsLpTlhmtF/
DkfP13H8k3/nUP9Y8FHt9+Ld56qpdqi/77ngCF84Ed4MFXKYkwyFFyHLMaBCw5zk
Z07qISAbj3UeRPug+8iBKpzNBUXvXqqOGHp2h0faXz+C0yG0l7HOkhZ3m+dDD6vN
6ABrMrS/ZuWdiW4PiJUejW81rlRKJaCgmTXMjjQCpgFeUqj6flB4sALp3amY9v7r
CZVL67wBZ4u4YeKW0q8j4Lh3DrT5M7IGPP2uT9tw0FiamgYByC2rV/SAecxbh8f5
NQJbL4uyJwcusOorRvaKOWU9KQaz5Q6dx9auHnmLC3A0WsEFxjgtVwG3iqw8zOeF
8E7Lk3kPcA==
=L2kR
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Removal of now unused busy wqe list (Hillf)
- Add cond_resched() to io-wq work processing (Hillf)
- And then the series that I hinted at from last week, which removes
the sqe from the io_kiocb and keeps all sqe handling on the prep
side. This guarantees that an opcode can't do the wrong thing and
read the sqe more than once. This is unchanged from last week, no
issues have been observed with this in testing. Hence I really think
we should fold this into 5.5.
* tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block:
io-wq: add cond_resched() to worker thread
io-wq: remove unused busy list from io_sqe
io_uring: pass in 'sqe' to the prep handlers
io_uring: standardize the prep methods
io_uring: read 'count' for IORING_OP_TIMEOUT in prep handler
io_uring: move all prep state for IORING_OP_{SEND,RECV}_MGS to prep handler
io_uring: move all prep state for IORING_OP_CONNECT to prep handler
io_uring: add and use struct io_rw for read/writes
io_uring: use u64_to_user_ptr() consistently
-----BEGIN PGP SIGNATURE-----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=IO44
-----END PGP SIGNATURE-----
Merge tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block
Pull libata fixes from Jens Axboe:
"Two things in here:
- First half of a series that fixes ahci_brcm, also marked for
stable. The other part of the series is going into 5.6 (Florian)
- sata_nv regression fix that is also marked for stable (Sascha)"
* tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block:
ata: ahci_brcm: Add missing clock management during recovery
ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINE
ata: ahci_brcm: Fix AHCI resources management
ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys()
libata: Fix retrieving of active qcs
-----BEGIN PGP SIGNATURE-----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=UOAX
-----END PGP SIGNATURE-----
Merge tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Only thing here are the changes from Arnd from last week, which now
have the appropriate header include to ensure they actually compile if
COMPAT is enabled"
* tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block:
compat_ioctl: block: handle Persistent Reservations
compat_ioctl: block: handle add zone open, close and finish ioctl
compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES
compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE
pktcdvd: fix regression on 64-bit architectures
- Fix the build for the Xtensa driver.
- Make sure to set up the parent device for mpc8xxx.
- Clarify the look-up error message.
- Fix the usage of the line direction in the mockup device.
- Fix a type warning on the Aspeed driver.
- Remove the pointless __exit annotation on the xgs-iproc which
is causing a compilation problem.
- Fix up emultation of open drain outputs .get_direction()
- Fix the IRQ callbacks on the PCA953xx to use bitops and
work properly.
- Fix the Kconfig on the Tegra driver.
-----BEGIN PGP SIGNATURE-----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=eZNi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A set of fixes for the v5.5 series:
- Fix the build for the Xtensa driver.
- Make sure to set up the parent device for mpc8xxx.
- Clarify the look-up error message.
- Fix the usage of the line direction in the mockup device.
- Fix a type warning on the Aspeed driver.
- Remove the pointless __exit annotation on the xgs-iproc which is
causing a compilation problem.
- Fix up emultation of open drain outputs .get_direction()
- Fix the IRQ callbacks on the PCA953xx to use bitops and work
properly.
- Fix the Kconfig on the Tegra driver"
* tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra186: Allow building on Tegra194-only configurations
gpio: pca953x: Switch to bitops in IRQ callbacks
gpiolib: fix up emulated open drain outputs
MAINTAINERS: Append missed file to the database
gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove
gpio: aspeed: avoid return type warning
gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION
gpio: Fix error message on out-of-range GPIO in lookup table
gpio: mpc8xxx: Add platform device to gpiochip->parent
gpio: xtensa: fix driver build
If fq_classify() recycles a struct fq_flow because
a socket structure has been reallocated, we do not
set sk->sk_pacing_status immediately, but later if the
flow becomes detached.
This means that any flow requiring pacing (BBR, or SO_MAX_PACING_RATE)
might fallback to TCP internal pacing, which requires a per-socket
high resolution timer, and therefore more cpu cycles.
Fixes: 218af599fa ("tcp: internal implementation for pacing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra says:
====================
bnx2x: Bug fixes
This series has changes in the area of vlan resources
management APIs to fix fw assert issue reported in max
vlan configuration testing over the PF.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing max vlan configuration on the PF, firmware gets
assert as driver was configuring number of vlans more than what
is supported per port/engine, it was figured out that there is an
implicit vlan (hidden default vlan consuming hardware cam entry resource)
which is configured default for all the clients (PF/VFs) on client_init
ramrod by the adapter implicitly, so when allocating resources among the
PFs this implicit vlan should be considered or total vlan entries should
be reduced by one to accommodate that default/implicit vlan entry.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although it has same value as MAX_MAC_CREDIT_E2,
use MAX_VLAN_CREDIT_E2 appropriately.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-12-23
The following pull-request contains BPF updates for your *net* tree.
We've added 2 non-merge commits during the last 1 day(s) which contain
a total of 4 files changed, 34 insertions(+), 31 deletions(-).
The main changes are:
1) Fix libbpf build when building on a read-only filesystem with O=dir
option, from Namhyung Kim.
2) Fix a precision tracking bug for unknown scalars, from Daniel Borkmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_OF_MDIO=n:
drivers/net/phy/mdio_bus.c:23:
include/linux/of_mdio.h:58:13: warning: ‘of_mdiobus_child_is_phy’ defined but not used [-Wunused-function]
static bool of_mdiobus_child_is_phy(struct device_node *child)
^~~~~~~~~~~~~~~~~~~~~~~
Fix this by adding the missing "inline" keyword.
Fixes: 0aa4d016c0 ("of: mdio: export of_mdiobus_child_is_phy")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The suspend/resume code for AQR107 works on AQR105 too.
This patch fixes issues with the partner not seeing the link down
when the interface using AQR105 is brought down.
Fixes: bee8259dd3 ("net: phy: add driver for aquantia phy")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the error path some fragments remain DMA mapped. Adding a fix
that unmaps all the fragments. Rework cleanup path to be simpler.
Fixes: 8151ee88ba ("dpaa_eth: use page backed rx buffers")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix endianness issue in flowtable TCP flags dissector,
from Arnd Bergmann.
2) Extend flowtable test script with dnat rules, from Florian Westphal.
3) Reject padding in ebtables user entries and validate computed user
offset, reported by syzbot, from Florian Westphal.
4) Fix endianness in nft_tproxy, from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The burning process requires to perform internal allocations of large
chunks of memory. This memory doesn't need to be contiguous and can be
safely allocated by vzalloc() instead of kzalloc(). This patch changes
such allocation to avoid possible out-of-memory failure.
Fixes: 410ed13cae ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae2 ("ata: ahci_brcm: Recover from failures to identify devices")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms")
Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
