This reverts commit bfdad565ae.
The patch turned out to be incorrect, and will be replaced
with a correct patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 098e30f655 "ARM: ixp4xx: stop broadcasting the custom GPIO API"
changed the internal gpio code of ixp4xx to be accessible only from
common.c, but unfortunately that broke the Goramo MultiLink code, which
uses this API.
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'set_scl':
arch/arm/mach-ixp4xx/goramo_mlr.c:82: error: implicit declaration of function 'gpio_line_set'
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'output_control':
arch/arm/mach-ixp4xx/goramo_mlr.c:111: error: implicit declaration of function 'gpio_line_config'
arch/arm/mach-ixp4xx/goramo_mlr.c:111: error: 'IXP4XX_GPIO_OUT' undeclared
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'hss_dcd_irq':
arch/arm/mach-ixp4xx/goramo_mlr.c:155: error: implicit declaration of function 'gpio_line_get'
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_init':
arch/arm/mach-ixp4xx/goramo_mlr.c:416: error: 'IXP4XX_GPIO_OUT' undeclared
arch/arm/mach-ixp4xx/goramo_mlr.c:421: error: 'IXP4XX_GPIO_IN' undeclared
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is the first batch of a much longer series of bug fixes
found during randconfig testing. This part are all the simple
patches that are applicable for the arm-soc tree, while most
other fixes will likely go through other maintainers.
* randconfig-fixes: (50 commits)
ARM: tegra: make debug_ll code build for ARMv6
ARM: sunxi: fix build for THUMB2_KERNEL
ARM: exynos: add missing include of linux/module.h
ARM: exynos: fix l2x0 saved regs handling
ARM: samsung: select CRC32 for SAMSUNG_PM_CHECK
ARM: samsung: select ATAGS where necessary
ARM: samsung: fix SAMSUNG_PM_DEBUG Kconfig logic
ARM: samsung: allow serial driver to be disabled
ARM: s5pv210: enable IDE support in MACH_TORBRECK
ARM: s5p64x0: fix building with only one soc type
ARM: s3c64xx: select power domains only when used
ARM: s3c64xx: MACH_SMDK6400 needs HSMMC1
ARM: s3c24xx: osiris dvs needs tps65010
ARM: s3c24xx: fix gta02 build error
ARM: s3c24xx: MINI2440 needs I2C for EEPROM_AT24
ARM: integrator: only select pl01x if TTY is enabled
ARM: realview: fix sparsemem build
ARM: footbridge: make screen_info setup conditional
ARM: footbridge: fix build with PCI disabled
ARM: footbridge: don't build floppy code for addin mode
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In a combined ARMv6/v7 kernel, we cannot use the
movt/movw instructions to load an immediate, as they
are not valid on ARMv6.
This changes the file to use an indirect load instead,
as lots of other implementations do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Building an SMP kernel for the sunxi platform with THUMB2 instructions
fails with this error at the moment:
headsmp.S:7: Error: Thumb encoding does not support an immediate here -- `msr cpsr_fsxc,#0xd3'
Since the generic secondary_startup function already does
the same thing in a safe way, we can just drop the private
sunxi implementation and jump straight to secondary_startup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
After the restructuring of the module.h and init.h headers,
we now need to include this explicitly here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The exynos4_l2x0_cache_init function tries to flush the data cache
for the location of the saved l2x0 registers and pass the physical
address to the s5p-sleep implementation.
However, the s5p-sleep code is optional, and if it is disabled,
we get a linker error here when the l2x0_regs_phys variable does
not exist.
To solve this, use a compile-time conditional to drop this code
if we don't want it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The Samsung pm_check code uses the crc32 library code, which can
be built as a loadable module, in which case we get a link error
building the kernel.
A better solution is to use 'select CRC32', which is what all
other users of this code do, as it ensures it is always built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Most of the Samsung platforms do not yet allow building with
DT at all, so we should select CONFIG_ATAGS for now in all
cases we also select CONFIG_SAMSUNG_ATAGS.
Found during randconfig testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The suspend debug code for Samsung has multiple dependencies
that we should not unconditionally enable. In particular,
we rely on the DEBUG_S3C_UART setting, which in turn depends
on the samsung UART driver.
Signed-off-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
If CONFIG_SERIAL_SAMSUNG is disabled, we run into build errors
with some samsung platforms. This adds a couple of #ifdef
statements to hopefully deal with this more gracefully.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Building MACH_TORBRECK by itself results in a build error
because we try to reference the s3c_device_cfcon definition
that is hidden inside CONFIG_SAMSUNG_DEV_IDE. This changes
the Kconfig logic to ensure that option is enabled when we
need it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The s5p64x0 platform supports two distinct SoCs, s5p6440 and s5p6450,
and in the normal configuration, both are enabled. However if we build
a kernel that only enables one of the two, the #ifdef logic in common.c
breaks down, as some of the functions declared in the header are defined
to NULL using the preprocessor but then defined anyway.
This patch cleans up the mess and ensures that each function has either
exactly one C declaration and one matching C definition, or we have
a NULL defined function pointer but no C definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The power domain code is only available when CONFIG_PM
is enabled, so we must not select that unconditionally for
s3c64xx. Changing it to 'select PM_GENERIC_DOMAINS if PM'
mirrors what we do on other platforms, and fixes a possible
randconfig build bug.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This board uses both MMC controllers, so we need to enable
the Kconfig option to define the platform data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The osiris-dvs driver calls functions exported by the tps65010
driver, so we have to ensure that driver is enabled first.
Using 'select' here doesn't work all that well, because it
requires I2C to be enabled in turn.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The gta02 has always been broken in the case when CONFIG_PCF50633_ADC
is not used, since gta02_charger_worker then passes a nonexisting
variable into the pcf50633_mbc_usb_curlim_set() function.
This addresses the obvious typo by using the variable that is
used everywhere else in this file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
If I2C is disabled, we cannot build the AT24 driver, so we
should not select it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Building the integrator platform without TTY support currently
results in a build failure because we always turn on the
pl010 or pl011 drivers. Changing this to a conditional 'select'
statement enables us to build more random configurations, although
it should have little impact for practical configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Commit b713aa0b15 "ARM: fix asm/memory.h build error" broke some
configurations on mach-realview with sparsemem enabled, which
is missing a definition of PHYS_OFFSET:
arch/arm/include/asm/memory.h:268:42: error: 'PHYS_OFFSET' undeclared (first use in this function)
#define PHYS_PFN_OFFSET ((unsigned long)(PHYS_OFFSET >> PAGE_SHIFT))
arch/arm/include/asm/dma-mapping.h:104:9: note: in expansion of macro 'PHYS_PFN_OFFSET'
return PHYS_PFN_OFFSET + dma_to_pfn(dev, *dev->dma_mask);
An easy workaround is for realview to define PHYS_OFFSET itself,
in the same way we define it for platforms that don't have a private
__virt_to_phys function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
The global screen_info structure is used to communicate
data about the console from platform code to the console
driver, but is only defined on ARM if either the VGA or
dummy consoles are in use.
This changes the footbridge code so we don't try to access
this structure in case it is not defined, which prevents
a possible randconfig build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
The dc21285.c source file cannot be built when CONFIG_PCI is
disabled, because it calls a number of PCI core interfaces.
This changes the Makefile so we don't include this file in the
build if CONFIG_PCI is disabled. No other code references anything
defined inside of this file in this case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
The ARCH_EBSA285_ADDIN platform does not provide the
ISA_DMA API, which is required by the floppy driver.
Let's ensure that the floppy code can only be built
when ISA_DMA is also enabled, by moving the select
statement into ARCH_EBSA285_HOST.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
ARCH_RPC no longer supports other CPUs aside from StrongARM110,
so we can make the option implicitly selected by the platform
and no longer give the option of building a kernel without CPU
support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
The trizeps4 and trizeps4wl platforms are both implemented
using the same board file. Since the trizeps4wl code is a
superset of trizeps4, it makes no sense to enable just the
latter, but with the current Kconfig logic, it causes the
board file not to be built at all.
Selecting MACH_TRIZEPS4 from MACH_TRIZEPS4WL ensures that
we are actually building the board file.
Found during randconfig testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The Arcom/Eurotech VIPER SBC enables the I2C_GPIO driver, but
that has a dependency on I2C, and causes build failures if I2C
is disabled. To keep existing configurations running while fixing
the randconfig problems, this changes the logic to only enable
I2C_GPIO if I2C is already enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Daniel Mack <zonque@gmail.com>
balloon3_udc_init() tries to register a balloon3_gpio_vbus
device, but this has never been defined in the mainline
kernel. To avoid the obvious build failure when this function
is enabled, remove the bogus reference here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The functions declared in include/linux/pxa2xx_ssp.h are
defined in plat-pxa/ssp.c, which can also be built for
PLAT_MMP, but may be disabled there. This can lead to
both unresolved symbols at link time and to duplicate
symbols at compile time for random configurations.
Changing the #ifdef in the header file to match the
Kconfig symbol that decides if the file is built solves
both problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The colibri_ohci_init function performs a register access through
the io_p2v() macro, which requires the IOMEM macro to be defined.
By explicitly including the asm/io.h header file that contains
this macro, we avoid the build error:
arch/arm/mach-pxa/colibri-evalboard.c: In function 'colibri_ohci_init':
arch/arm/mach-pxa/colibri-evalboard.c:68:2: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The SAAR and TAVOREVB machines try to call functions from
the PXAFB frame buffer driver from their platform code,
which only works if that driver is built-in.
This patch ensures that both the generic frame buffer
code and the specific pxafb driver are always enabled
when we build a kernel for one of the two boards.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
We normally don't hard-enable Kconfig options just because
a board contains a specific piece of hardware. In this case,
selecting SMC91X causes a build error, if we don't also enable
basic network device driver support.
Since the platform has no direct dependency on this driver
at link time, we can just remove the 'select' statement.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Mack <zonque@gmail.com>
The D-Link DNS-323 machine tries to unconditionally select CONFIG_PHYLIB,
but that has other dependencies that might not necessarily be enabled,
causing random build errors.
To work around this, this patch removes the 'select' statement and
instead uses a compile-time check to skip the phy_register_fixup_for_uid()
call if PHYLIB is not available in the kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The definition for SIGBUS may not be visible without including
linux/signal.h, as I found during randconfig testing.
Adding an explicit include is certainly the right thing to do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The code for h2 and osk implicitly assumes that the tps65010
driver is built-in, in order to perform the initial regulator
setup.
This is fine for most real uses, but it does get into the way
of build testing with 'make randconfig', since we don't want
platforms to implicitly select device drivers and subsystems
such as I2C.
This patch by contrast changes the board files to not call
into the tps65010 driver when that is not built-in, allowing
us to build all configurations including some that will not
work properly on this hardware.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
If CONFIG_OMAP_32K_TIMER isn't enabled, we will
try to use enable_dyn_sleep which wasn't defined
anywhere.
In order to fix the problem, we always define
enable_dyn_sleep as 0 when !CONFIG_OMAP_32K_TIMER.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The msm_sdcc MMC driver and the msm_serial_hs uart driver both
use the pre-dmaengine interfaces provided by the MSM platform.
Since these drivers can be loadable modules, we should export
the functions used in the drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
MSM7X00A has an open-coded version of debug_ll_io_init so it
can use MT_DEVICE_NONSHARED as required by the platform.
However, this fails to build on no-MMU kernels because the
debug_ll_addr function is not available. Since the iotable_init
function doesn't actually do anyting in this configuration,
we can simply get away by enclosing the broken function call
in an #ifdef, which seems to be the least ugly workaround.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
After the restructuring of the module.h and init.h headers,
we now need to include this explicitly here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
This symbol is used by the lpc_eth driver, which may
be a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roland Stigge <stigge@antcom.de>
The 'og' machine tries to always initialized the PCI code, but that
may be disabled in Kconfig, leading to a build error.
This patch changes the code to use the same Kconfig symbol to decide
about calling the ks8695_init_pci function at build time that we
use to decide about building the ks8695 PCI support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Commit 098e30f655 "ARM: ixp4xx: stop broadcasting the custom GPIO API"
changed the internal gpio code of ixp4xx to be accessible only from
common.c, but unfortunately that broke the Goramo MultiLink code, which
uses this API.
This tries to restore the previous state without exposing the
API globally again. A better solution might be needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Imre Kaloz <kaloz@openwrt.org>
When using CONFIG_IXP4XX_INDIRECT_PCI, we run into a recursive
header file dependency between mach/io.h and asm/pci.h, resulting
in a build failure:
mach-ixp4xx/include/mach/io.h: In function 'is_pci_memory':
mach-ixp4xx/include/mach/io.h:53:18: error: 'PCIBIOS_MIN_MEM' undeclared (first use in this function)
return (addr >= PCIBIOS_MIN_MEM) && (addr <= 0x4FFFFFFF);
^
mach-ixp4xx/include/mach/io.h:53:18: note: each undeclared identifier is reported only once for each function it appears in
We can work around this by referencing the pcibios_min_mem variable
directly through an extern declaration, rather than using the macro.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
The omixp board code unconditionally defines a gpio-led
device, but for some reason includes the header file
for this only if CONFIG_LEDS_CLASS is enabled, causing
a build error otherwise.
Removing the #ifdef fixes the build error with no downsides
whatsoever.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
The hisi SMP code always uses the hi3xxx_set_cpu() function
defined in the hotplug.c file, so we cannot build without
this when CONFIG_SMP is enabled. This patch slightly restructures
the code so we always build the parts of hotplug.c that we need
but just leave out the CPU disable logic if CONFIG_HOTPLUG_CPU
is turned off.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
ep93xx_chip_revision is used by the pata_ep93xx driver,
which can be a loadable module. Exporting the symbol
avoids a link error in this case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
The efm32 platform does not provide a zreladdr-y line its Makefile.boot,
so we always have to use CONFIG_AUTO_ZRELADDR in order to successfully
build and link a zImage.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Uwe Kleine-König <kernel@pengutronix.de>
The DAVINCI_DA850_EVM board uses an unusual method to
enable the GPIO_PCA953X and KEYBOARD_GPIO_POLLED symbols,
which leads to the dependencies on these symbols being
ignored. As GPIO_PCA953X actually requires I2C, that
can lead to build failures when I2C is disabled.
This patch removes the duplicate symbol definitions
and instead enables them from the davinci_all_defconfig
file.
A different question whether we actually want to automatically
enable them at all or rather put them into defconfig,
but that should be a separate patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
We cannot call phy_register_fixup_for_uid() if CONFIG_PHYLIB
is not built into the kernel, and we should not enforce that
to be built into vmlinux either, because one might want to
disable the entire network stack.
This change uses a compile-time condition on CONFIG_PHYLIB
to remove the call in the cases where it cannot work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
It makes no sense for sama5 support to be enabled if we don't
also enable USE_OF. Making this automatic in Kconfig avoids
a possible randconfig conflict between the old and new clock
support code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
