We need an accurate and continuous (monotonic) time sources to do
accurate synchronization among more timing sources. This patch allows
to enable monotonic timestamps for ALSA PCM devices and enables monotonic
timestamps for ALSA timer devices.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* support for switching rate in STAC9460 - using set_rate_val of the akm
infrastructure
* listing all STAC9460 registers in proc
* disabling mpu401 device for Prodigy192 - otherwise the currently
flawed mpu401 code hangs kernel when opening the midi device
* removing old unused commented-out code
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
remove dead config symbols from sound code
Signed-off-by: Jiri Olsa <olsajiri@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Updated the forgotten SNDRV_HWDEP_IFACE_LAST to point the really last member.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove sequencer instrument layer from the tree.
This mechanism hasn't been used much with the actual devices. The only
reasonable user was OPL3 loader, and now it was rewritten to use hwdep
instead. So, let's remove the rest of rotten codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the exclusive access lock in hwdep instead of the own one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the hwdep device for loading OPL2/3 patch data instead of the
messy sequencer instrument layer.
Due to this change, the sbiload program should be updated, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
* 'for-2.6.25' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (454 commits)
[POWERPC] Cell IOMMU fixed mapping support
[POWERPC] Split out the ioid fetching/checking logic
[POWERPC] Add support to cell_iommu_setup_page_tables() for multiple windows
[POWERPC] Split out the IOMMU logic from cell_dma_dev_setup()
[POWERPC] Split cell_iommu_setup_hardware() into two parts
[POWERPC] Split out the logic that allocates struct iommus
[POWERPC] Allocate the hash table under 1G on cell
[POWERPC] Add set_dma_ops() to match get_dma_ops()
[POWERPC] 83xx: Clean up / convert mpc83xx board DTS files to v1 format.
[POWERPC] 85xx: Only invalidate TLB0 and TLB1
[POWERPC] 83xx: Fix typo in mpc837x compatible entries
[POWERPC] 85xx: convert sbc85* boards to use machine_device_initcall
[POWERPC] 83xx: rework platform Kconfig
[POWERPC] 85xx: rework platform Kconfig
[POWERPC] 86xx: Remove unused IRQ defines
[POWERPC] QE: Explicitly set address-cells and size cells for muram
[POWERPC] Convert StorCenter DTS file to /dts-v1/ format.
[POWERPC] 86xx: Convert all 86xx DTS files to /dts-v1/ format.
[PPC] Remove 85xx from arch/ppc
[PPC] Remove 83xx from arch/ppc
...
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
alpha: fix x86.git merge build error
ia64: on UP percpu variables are not small memory model
x86: fix arch/x86/kernel/test_nx.c modular build bug
s390: use generic percpu linux-2.6.git
POWERPC: use generic per cpu
ia64: use generic percpu
SPARC64: use generic percpu
percpu: change Kconfig to HAVE_SETUP_PER_CPU_AREA
modules: fold percpu_modcopy into module.c
x86: export copy_from_user_ll_nocache[_nozero]
x86: fix duplicated TIF on 64-bit
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (27 commits)
lguest: use __PAGE_KERNEL instead of _PAGE_KERNEL
lguest: Use explicit includes rateher than indirect
lguest: get rid of lg variable assignments
lguest: change gpte_addr header
lguest: move changed bitmap to lg_cpu
lguest: move last_pages to lg_cpu
lguest: change last_guest to last_cpu
lguest: change spte_addr header
lguest: per-vcpu lguest pgdir management
lguest: make pending notifications per-vcpu
lguest: makes special fields be per-vcpu
lguest: per-vcpu lguest task management
lguest: replace lguest_arch with lg_cpu_arch.
lguest: make registers per-vcpu
lguest: make emulate_insn receive a vcpu struct.
lguest: map_switcher_in_guest() per-vcpu
lguest: per-vcpu interrupt processing.
lguest: per-vcpu lguest timers
lguest: make hypercalls use the vcpu struct
lguest: make write() operation smp aware
...
Manual conflict resolved (maybe even correctly, who knows) in
drivers/lguest/x86/core.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
security: compile capabilities by default
selinux: make selinux_set_mnt_opts() static
SELinux: Add warning messages on network denial due to error
SELinux: Add network ingress and egress control permission checks
NetLabel: Add auditing to the static labeling mechanism
NetLabel: Introduce static network labels for unlabeled connections
SELinux: Allow NetLabel to directly cache SIDs
SELinux: Enable dynamic enable/disable of the network access checks
SELinux: Better integration between peer labeling subsystems
SELinux: Add a new peer class and permissions to the Flask definitions
SELinux: Add a capabilities bitmap to SELinux policy version 22
SELinux: Add a network node caching mechanism similar to the sel_netif_*() functions
SELinux: Only store the network interface's ifindex
SELinux: Convert the netif code to use ifindex values
NetLabel: Add IP address family information to the netlbl_skbuff_getattr() function
NetLabel: Add secid token support to the NetLabel secattr struct
NetLabel: Consolidate the LSM domain mapping/hashing locks
NetLabel: Cleanup the LSM domain hash functions
NetLabel: Remove unneeded RCU read locks
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
PPC: Fix powerpc vio_find_name to not use devices_subsys
Driver core: add bus_find_device_by_name function
Module: check to see if we have a built in module with the same name
x86: fix runtime error in arch/x86/kernel/cpu/mcheck/mce_amd_64.c
Driver core: Fix up build when CONFIG_BLOCK=N
a5a19c63f4 removed the include of
asm/pgalloc.h from asm-generic/tlb.h. That works fine on most
architectures, but broke ALPHA.
Fixup ALPHA by adding the include to asm-alpha/tlbflush.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tony says:
| The CONFIG_SMP=n path in ia64 makes quite radical changes ... rather
| than putting all the per-cpu stuff into the top 64K of address space
| and providing a per-cpu TLB mapping for that range to a different
| physical address ... it just makes all the per-cpu stuff link as ordinary
| variables in .data.
the new generic percpu code got confused about this as PER_CPU_ATTRIBUTES
was defined even on UP, so it picked up that small memory model - which
was not possible to get linked. The right fix is to only define that
on SMP. This resolved the build failures in my cross-compiling environment.
also link these variables into the .percpu section even on UP - some
assembly code has offset dependencies. (such as GET_IA64_MCA_DATA() in
arch/ia64/kernel/mca_asm.S)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Tony Luck <tony.luck@intel.com>
Change s390 percpu.h to use asm-generic/percpu.h
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Powerpc has a way to determine the address of the per cpu area of the
currently executing processor via the paca and the array of per cpu
offsets is avoided by looking up the per cpu area from the remote
paca's (copying x86_64).
Cc: Paul Mackerras <paulus@samba.org>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Geoff Levand <geoffrey.levand@am.sony.com>
ia64 has a special processor specific mapping that can be used to locate the
offset for the current per cpu area.
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sparc64 has a way of providing the base address for the per cpu area of the
currently executing processor in a global register.
Sparc64 also provides a way to calculate the address of a per cpu area
from a base address instead of performing an array lookup.
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
percpu_modcopy() is defined multiple times in arch files. However, the only
user is module.c. Put a static definition into module.c and remove
the definitions from the arch files.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
commit 7e9916040b
and commit eee3af4a2c
Both use the same TIF number (25) in thread_info_64.h.
This patch changes the TIF ids.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
At the block level bidi request uses req->next_rq pointer for a second
bidi_read request.
At Scsi-midlayer a second scsi_data_buffer structure is used for the
bidi_read part. This bidi scsi_data_buffer is put on
request->next_rq->special. Struct scsi_cmnd is not changed.
- Define scsi_bidi_cmnd() to return true if it is a bidi request and a
second sgtable was allocated.
- Define scsi_in()/scsi_out() to return the in or out scsi_data_buffer
from this command This API is to isolate users from the mechanics of
bidi.
- Define scsi_end_bidi_request() to do what scsi_end_request() does but
for a bidi request. This is necessary because bidi commands are a bit
tricky here. (See comments in body)
- scsi_release_buffers() will also release the bidi_read scsi_data_buffer
- scsi_io_completion() on bidi commands will now call
scsi_end_bidi_request() and return.
- The previous work done in scsi_init_io() is now done in a new
scsi_init_sgtable() (which is 99% identical to old scsi_init_io())
The new scsi_init_io() will call the above twice if needed also for
the bidi_read command. Only at this point is a command bidi.
- In scsi_error.c at scsi_eh_prep/restore_cmnd() make sure bidi-lld is not
confused by a get-sense command that looks like bidi. This is done
by puting NULL at request->next_rq, and restoring.
[jejb: update to sg_table and resolve conflicts
also update to blk-end-request and resolve conflicts]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In preparation for bidi we abstract all IO members of scsi_cmnd,
that will need to duplicate, into a substructure.
- Group all IO members of scsi_cmnd into a scsi_data_buffer
structure.
- Adjust accessors to new members.
- scsi_{alloc,free}_sgtable receive a scsi_data_buffer instead of
scsi_cmnd. And work on it.
- Adjust scsi_init_io() and scsi_release_buffers() for above
change.
- Fix other parts of scsi_lib/scsi.c to members migration. Use
accessors where appropriate.
- fix Documentation about scsi_cmnd in scsi_host.h
- scsi_error.c
* Changed needed members of struct scsi_eh_save.
* Careful considerations in scsi_eh_prep/restore_cmnd.
- sd.c and sr.c
* sd and sr would adjust IO size to align on device's block
size so code needs to change once we move to scsi_data_buff
implementation.
* Convert code to use scsi_for_each_sg
* Use data accessors where appropriate.
- tgt: convert libsrp to use scsi_data_buffer
- isd200: This driver still bangs on scsi_cmnd IO members,
so need changing
[jejb: rebased on top of sg_table patches fixed up conflicts
and used the synergy to eliminate use_sg and sg_count]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we export scsi_init_io()/scsi_release_buffers() instead of
scsi_{alloc,free}_sgtable() from scsi_lib than tgt code is much more
insulated from scsi_lib changes. As a bonus it will also gain bidi
capability when it comes.
[jejb: rebase on to sg_table and fix up rejections]
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Migrating the apic timer in the critical section is not very nice, and is
absolutely horrible with the real-time port. Move migration to the regular
vcpu execution path, triggered by a new bitflag.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
kvm_para.h potentially contains definitions that are to be used by userspace,
so it should not be included inside the __KERNEL__ block. To protect its own
data structures, kvm_para.h already includes its own __KERNEL__ block.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Acked-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch moves kvm_fpu asm-x86/kvm.h to allow every architecture to
define an own representation used for KVM_GET_FPU/KVM_SET_FPU.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Acked-by: Carsten Otte <cotte@de.ibm.com>
Acked-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
When executing a test program called "crashme", we found the KVM guest cannot
survive more than ten seconds, then encounterd kernel panic. The basic concept
of "crashme" is generating random assembly code and trying to execute it.
After some fixes on emulator insn validity judgment, we found it's hard to
get the current emulator handle the invalid instructions correctly, for the
#UD trap for hypercall patching caused troubles. The problem is, if the opcode
itself was OK, but combination of opcode and modrm_reg was invalid, and one
operand of the opcode was memory (SrcMem or DstMem), the emulator will fetch
the memory operand first rather than checking the validity, and may encounter
an error there. For example, ".byte 0xfe, 0x34, 0xcd" has this problem.
In the patch, we simply check that if the invalid opcode wasn't vmcall/vmmcall,
then return from emulate_instruction() and inject a #UD to guest. With the
patch, the guest had been running for more than 12 hours.
Signed-off-by: Feng (Eric) Liu <eric.e.liu@intel.com>
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Convert the synchronization of the shadow handling to a separate mmu_lock
spinlock.
Also guard fetch() by mmap_sem in read-mode to protect against alias
and memslot changes.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Since gfn_to_page() is a sleeping function, and we want to make the core mmu
spinlocked, we need to pass the page from the walker context (which can sleep)
to the shadow context (which cannot).
[marcelo: avoid recursive locking of mmap_sem]
Signed-off-by: Avi Kivity <avi@qumranet.com>
In preparation for a mmu spinlock, add kvm_read_guest_atomic()
and use it in fetch() and prefetch_page().
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This adds a mechanism for exposing the virtual apic tpr to the guest, and a
protocol for letting the guest update the tpr without causing a vmexit if
conditions allow (e.g. there is no interrupt pending with a higher priority
than the new tpr).
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add a facility to report on accesses to the local apic tpr even if the
local apic is emulated in the kernel. This is basically a hack that
allows userspace to patch Windows which tends to bang on the tpr a lot.
Signed-off-by: Avi Kivity <avi@qumranet.com>
IA64 also needs to see ioapic structure in irqchip.
Signed-off-by: xiantao.zhang@intel.com <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Moving kvm_vcpu_kick() to x86.c. Since it should be
common for all archs, put its declarations in <linux/kvm_host.h>
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This paves the way for multiple architecture support. Note that while
ioapic.c could potentially be shared with ia64, it is also moved.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently, make headers_check barfs due to <asm/kvm.h>, which <linux/kvm.h>
includes, not existing. Rather than add a zillion <asm/kvm.h>s, export kvm.h
only if the arch actually supports it.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch fixes a small issue where sturctures:
kvm_pic_state
kvm_ioapic_state
are defined inside x86 specific code and may or may not
be defined in anyway for other architectures. The problem
caused is one cannot compile userspace apps (ex. libkvm)
for other archs since a size cannot be determined for these
structures.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The current cpuid management suffers from several problems, which inhibit
passing through the host feature set to the guest:
- No way to tell which features the host supports
While some features can be supported with no changes to kvm, others
need explicit support. That means kvm needs to vet the feature set
before it is passed to the guest.
- No support for indexed or stateful cpuid entries
Some cpuid entries depend on ecx as well as on eax, or on internal
state in the processor (running cpuid multiple times with the same
input returns different output). The current cpuid machinery only
supports keying on eax.
- No support for save/restore/migrate
The internal state above needs to be exposed to userspace so it can
be saved or migrated.
This patch adds extended cpuid support by means of three new ioctls:
- KVM_GET_SUPPORTED_CPUID: get all cpuid entries the host (and kvm)
supports
- KVM_SET_CPUID2: sets the vcpu's cpuid table
- KVM_GET_CPUID2: gets the vcpu's cpuid table, including hidden state
[avi: fix original KVM_SET_CPUID not removing nx on non-nx hosts as it did
before]
Signed-off-by: Dan Kenigsberg <danken@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch moves structures:
kvm_cpuid_entry
kvm_cpuid
from include/linux/kvm.h to include/asm-x86/kvm.h
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Move structures:
kvm_sregs
kvm_msr_entry
kvm_msrs
kvm_msr_list
from include/linux/kvm.h to include/asm-x86/kvm.h
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch moves structures:
kvm_segment
kvm_dtable
from include/linux/kvm.h to include/asm-x86/kvm.h
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch moves structure lapic_state from include/linux/kvm.h
to include/asm-x86/kvm.h
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch moves structure kvm_regs to include/asm-x86/kvm.h.
Each architecture will need to create there own version of this
structure.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch moves structures:
kvm_pic_state
kvm_ioapic_state
to inclue/asm-x86/kvm.h.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch moves sturct kvm_memory_alias from include/linux/kvm.h
to include/asm-x86/kvm.h. Also have include/linux/kvm.h include
include/asm/kvm.h.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently kvm has a wart in that it requires three extra pages for use
as a tss when emulating real mode on Intel. This patch moves the allocation
internally, only requiring userspace to tell us where in the physical address
space we can place the tss.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently kvm provides hypercalls only for x86* architectures. To
provide hypercall infrastructure for other kvm architectures I split
kvm_para.h into a generic header file and architecture specific
definitions.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Instead of having the kernel allocate memory to the guest, let userspace
allocate it and pass the address to the kernel.
This is required for s390 support, but also enables features like memory
sharing and using hugetlbfs backed memory.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The user is now able to set how many mmu pages will be allocated to the guest.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch refactors the current hypercall infrastructure to better
support live migration and SMP. It eliminates the hypercall page by
trapping the UD exception that would occur if you used the wrong hypercall
instruction for the underlying architecture and replacing it with the right
one lazily.
A fall-out of this patch is that the unhandled hypercalls no longer trap to
userspace. There is very little reason though to use a hypercall to
communicate with userspace as PIO or MMIO can be used. There is no code
in tree that uses userspace hypercalls.
[avi: fix #ud injection on vmx]
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Use a standard list threaded through page->lru for maintaining the pgd
list on PAE. This is the same as 64-bit, and seems saner than using a
non-standard list via page->index.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
PAE mode requires that we reload cr3 in order to guarantee that
changes to the pgd will be noticed by the processor. This means that
in principle pud_clear needs to reload cr3 every time. However,
because reloading cr3 implies a tlb flush, we want to avoid it where
possible.
pud_clear() is only used in a couple of places:
- in free_pmd_range(), when pulling down a range of process address space, and
- huge_pmd_unshare()
In both cases, the calling code will do a a tlb flush anyway, so
there's no need to do it within pud_clear().
In free_pmd_range(), the pud_clear is immediately followed by
pmd_free_tlb(); we can hook that to make the mmu_gather do an
unconditional full flush to make sure cr3 gets reloaded.
In huge_pmd_unshare, it is followed by flush_tlb_range, which always
results in a full cr3-reload tlb flush.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: William Irwin <wli@holomorphy.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds a new configuration option, which adds support for a new
early_param which gets checked in arch/x86/kernel/setup_{32,64}.c:setup_arch()
to decide wether OHCI-1394 FireWire controllers should be initialized and
enabled for physical DMA access to allow remote debugging of early problems
like issues ACPI or other subsystems which are executed very early.
If the config option is not enabled, no code is changed, and if the boot
paramenter is not given, no new code is executed, and independent of that,
all new code is freed after boot, so the config option can be even enabled
in standard, non-debug kernels.
With specialized tools, it is then possible to get debugging information
from machines which have no serial ports (notebooks) such as the printk
buffer contents, or any data which can be referenced from global pointers,
if it is stored below the 4GB limit and even memory dumps of of the physical
RAM region below the 4GB limit can be taken without any cooperation from the
CPU of the host, so the machine can be crashed early, it does not matter.
In the extreme, even kernel debuggers can be accessed in this way. I wrote
a small kgdb module and an accompanying gdb stub for FireWire which allows
to gdb to talk to kgdb using remote remory reads and writes over FireWire.
An version of the gdb stub fore FireWire is able to read all global data
from a system which is running a a normal kernel without any kernel debugger,
without any interruption or support of the system's CPU. That way, e.g. the
task struct and so on can be read and even manipulated when the physical DMA
access is granted.
A HOWTO is included in this patch, in Documentation/debugging-via-ohci1394.txt
and I've put a copy online at
ftp://ftp.suse.de/private/bk/firewire/docs/debugging-via-ohci1394.txt
It also has links to all the tools which are available to make use of it
another copy of it is online at:
ftp://ftp.suse.de/private/bk/firewire/kernel/ohci1394_dma_early-v2.diff
Signed-Off-By: Bernhard Kaindl <bk@suse.de>
Tested-By: Thomas Renninger <trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In x86 PAE mode, stop treating pmds as a special case. Previously
they were always allocated and freed with the pgd. The modifies the
code to be the same as 64-bit mode, where they are allocated on
demand.
This is a step on the way to unifying 32/64-bit pagetable allocation
as much as possible.
There is a complicating wart, however. When you install a new
reference to a pmd in the pgd, the processor isn't guaranteed to see
it unless you reload cr3. Since reloading cr3 also has the
side-effect of flushing the tlb, this is an expense that we want to
avoid whereever possible.
This patch simply avoids reloading cr3 unless the update is to the
current pagetable. Later patches will optimise this further.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: William Irwin <wli@holomorphy.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Yes! A mere 120 c_p_a() fixing and rewriting patches later,
we are now confident that we can enable UC by default for
ioremap(), on x86 too.
Every other architectures was doing this already. Doing so
makes Linux more robust against MTRR mixups (which might go
unnoticed if BIOS writers test other OSs only - where PAT
might override bad MTRRs defaults).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Latest update; I now have 4 NX tests, but 2 fail so they're #if 0'd.
I also cleaned up the NX test code quite a bit, and got rid of the ugly
exception table sorting stuff.
From: Arjan van de Ven <arjan@linux.intel.com>
This patch adds testcases for the CONFIG_DEBUG_RODATA configuration option
as well as the NX CPU feature/mappings. Both testcases can move to tests/
once that patch gets merged into mainline.
(I'm half considering moving the rodata test into mm/init.c but I'll
wait with that until init.c is unified)
As part of this I had to fix a not-quite-right alignment in the vmlinux.lds.h
for the RODATA sections, which lead to 1 page less being marked read only.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The set_memory_* and set_pages_* family of API's currently requires the
callers to do a global tlb flush after the function call; forgetting this is
a very nasty deathtrap. This patch moves the global tlb flush into
each of the callers
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
change_page_attr_add is only used in pageattr.c now, so we can
make this function static.
change_page_attr() isn't used anywere at all anymore; this function
is a really bad API anyway so just remove the bloat entirely.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
page_is_ram has a FIXME since ages, which reminds to sanity check the
BIOS area between 640k and 1M, which is sometimes falsely reported as
RAM in the e820 tables.
Implement the sanity check. Move the BIOS range defines from
pageattr.c into e820.h to avoid duplicate defines.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With the introduction of the new API, no driver or non-archcore code needs
to use c-p-a anymore, so this patch also deprecates the EXPORT_SYMBOL of CPA
(it's a horrible API after all).
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch converts various users of change_page_attr() to the new,
more intent driven set_page_*/set_memory_* API set.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Right now, if drivers or other code want to change, say, a cache attribute of a
page, the only API they have is change_page_attr(). c-p-a is a really bad API
for this, because it forces the caller to know *ALL* the attributes he wants
for the page, not just the 1 thing he wants to change. So code that wants to
set a page uncachable, needs to be aware of the NX status as well etc etc etc.
This patch introduces a set of new APIs for this, set_pages_<attr> and
set_memory_<attr>, that offer a logical change to the user, and leave all
attributes not implied by the requested logical change alone.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64bit uses end_pfn_map and 32bit uses max_low_pfn. There are several
files which have #ifdef'ed defines which map either to end_pfn_map or
max_low_pfn. Replace this by a universal define and clean up all the
other instances.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
do some leftover cleanups in the now unified arch/x86/mm/pageattr.c
file.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
get more testing of the c_p_a() code done by not turning off
PSE on DEBUG_PAGEALLOC.
this simplifies the early pagetable setup code, and tests
the largepage-splitup code quite heavily.
In the end, all the largepages will be split up pretty quickly,
so there's no difference to how DEBUG_PAGEALLOC worked before.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes some bugs of making EFI runtime code executable.
- Use change_page_attr in i386 too. Because the runtime code may be
mapped not through ioremap.
- If there is no _PAGE_NX in __supported_pte_mask, the change_page_attr
is not called.
- Make efi_ioremap map pages as PAGE_KERNEL_EXEC_NOCACHE, because EFI runtime
code may be mapped through efi_ioremap.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The SMP trampoline always runs in real mode, so making it executable
in the page tables doesn't make much sense because it executes
before page tables are set up. That was the only user of
set_kernel_exec(). Remove set_kernel_exec().
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The pte_* modifier functions that cleared bits dropped the NX bit on 32bit
PAE because they only worked in int, but NX is in bit 63. Fix that
by adding appropiate casts so that the arithmetic happens as long long
on PAE kernels.
I decided to just use 64bit arithmetic instead of open coding like
pte_modify() because gcc should generate good enough code for that now.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
64bit already had it.
Needed for later patches.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
No need to make it 64bit there.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix a long-standing weakness of the early-ioremap allocator: it
uses a single pgd entry for the boot mappings, and was not properly
protecting itself against crossing a 2MB (4MB) boundary.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
increase max early_ioremap() remapping size from 64K to 256K.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch renames bt_ioremap to early_ioremap, which is used in
x86_64. This makes it easier to merge i386 and x86_64 usage.
[ mingo@elte.hu: fix ]
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch replaces boot_ioremap invokation with bt_ioremap and
removes the boot_ioremap implementation.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes it possible for bt_ioremap() to be used before
paging_init(), via providing an early implementation of set_fixmap()
that can be used before paging_init().
This way boot_ioremap() can be replaced by bt_ioremap().
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on this patch from Andi Kleen:
| Subject: CPA: Return the page table level in lookup_address()
| From: Andi Kleen <ak@suse.de>
|
| Needed for the next change.
|
| And change all the callers.
and ported it to x86.git.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Needed for some test code.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Rename it to pte_exec() from pte_exec_kernel(). There is nothing
kernel specific in there.
- Move it into the common file because _PAGE_NX is 0 on !PAE and then
pte_exec() will be always evaluate to true.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Prepare ioremap() to default to uncached. This will be the
safest - but first we have to fix CPA.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert macros into inline functions, for better type-checking.
This patch required a little bit of fiddling with headers in order to
make __(pte|pmd)_free_tlb inline rather than macros.
asm-generic/tlb.h includes asm/pgalloc.h, though it doesn't directly
use any pgalloc definitions. I removed this include to avoid an
include cycle, but it may cause secondary compile failures by things
depending on the indirect inclusion; arch/x86/mm/hugetlbpage.c was one
such place; there may be others.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add mm to paravirt_alloc_pd, partly to make it consistent with
paravirt_alloc_pt, and because later changes will make use of it.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds support for the RDC R-321x system-on-chip,
also known as R-861x-(G). It uses the generic GPIO API and
has support for the on-chip hardware watchdog.
Build-fix from: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch defines the PCI identifiers found in
the RDC R-321x System-on-Chip.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds the generic GPIO support to the x86
architecture. We do the same as for MIPS, we let
the machine override the gpio callbacks and provide
defaults one in mach-generic.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The existing Geode GPIO API only allows for updating one GPIO at once. There
are instances where users want to update multiple GPIOs at once. With the
current API, they are given two choices; either ignore the GPIO API:
outl(0xc000, gpio_base + GPIO_OUTPUT_VAL);
outl(0xc000, gpio_base + GPIO_OUTPUT_ENABLE);
Alternatively, call each GPIO update separately:
geode_gpio_set(14, GPIO_OUTPUT_VAL);
geode_gpio_set(15, GPIO_OUTPUT_VAL);
geode_gpio_set(14, GPIO_OUTPUT_ENABLE);
geode_gpio_set(15, GPIO_OUTPUT_ENABLE);
Neither are desirable. This patch changes the GPIO API to allow for setting
of multiple GPIOs at once; rather than being passed an integer, we pass
a bitmask and provide a translation function. The above code would now
look like this:
geode_gpio_set(geode_gpio(14)|geode_gpio(15), GPIO_OUTPUT_VAL);
geode_gpio_set(geode_gpio(14)|geode_gpio(15), GPIO_OUTPUT_ENABLE);
Since there are no upstream users of the GPIO API yet (afaik), best to
change this now. This also adds a bit of sanity checking; it is no
longer possible to use a GPIO above 28.
Note the semantics of geode_gpio_isset() have changed:
geode_gpio_isset(geode_gpio(3)|geode_gpio(4), ...)
will only return true iff both GPIOs are set.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
when MTRRs are not covering the whole e820 table, we need to trim the
RAM and need to update e820.
reuse some code on 64-bit as well.
here need to add early_get_cap and use it in early_cpu_detect, and move
mtrr_bp_init early.
The code successfully trimmed the memory map on Justin's system:
from:
[ 0.000000] BIOS-e820: 0000000100000000 - 000000022c000000 (usable)
to:
[ 0.000000] modified: 0000000100000000 - 0000000228000000 (usable)
[ 0.000000] modified: 0000000228000000 - 000000022c000000 (reserved)
According to Justin it makes quite a difference:
| When I boot the box without any trimming it acts like a 286 or 386,
| takes about 10 minutes to boot (using raptor disks).
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
enabled, then interrupts don't work for the rtc-cmos driver which results in
RTC_AIE*, RTC_PIE* and RTC_ALM being unusable. This affects hwclock from
util-linux-ng at least on i386 since that uses RTC_PIE_ON. (For x86-64, a
polling method is used for unknown reasons.)
This patch series now
1. export the functions from arch/x86/kernel/hpet.c that the old char/rtc
driver uses to work around that problem,
2. makes it possible to compile the old rtc driver as module, while still
having CONFIG_HPET_EMULATE_RTC enabled and
3. makes use of the exported functions in (1) in the new rtc-cmos driver.
This patch:
This patch makes the RTC emulation functions in arch/x86/kernel/hpet.c usable
for kernel modules. It
- exports the functions (EXPORT_SYMBOL_GPL()),
- adds an interface to register the interrupt callback function
instead of using only a fixed callback function and
- replaces the rtc_get_rtc_time() function which depends on
CONFIG_RTC with a call to get_rtc_time() which is defined in
include/asm-generic/rtc.h.
The only dependency to CONFIG_RTC is the call to rtc_interrupt() which is
removed by the next patch. After this, there's no (code) dependency of
this functions to CONFIG_RTC=y any more.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Robert Picco <Robert.Picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change the size of node ids for X86_64 from u8 to s16 to
accomodate more than 32k nodes and allow for NUMA_NO_NODE
(-1) to be sign extended to int.
Cc: David Rientjes <rientjes@google.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
call early_cpu_to_node() since per_cpu(cpu_to_node_map) might not be setup
yet.
I also had to export x86_cpu_to_node_map_early_ptr because of some calls
from the network code to numa_node_id():
net/ipv4/netfilter/arp_tables.c:
net/ipv4/netfilter/ip_tables.c:
net/ipv4/netfilter/ip_tables.c:
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provide a means to trap usages of per_cpu map variables before
they are setup. Define CONFIG_DEBUG_PER_CPU_MAPS to activate.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change the following static arrays sized by NR_CPUS to
per_cpu data variables:
char cpu_to_node_map[NR_CPUS];
fixup:
- Split cpu_to_node function into "early" and "late" versions
so that x86_cpu_to_node_map_early_ptr is not EXPORT'ed and
the cpu_to_node inline function is more streamlined.
- This also involves setting up the percpu maps as early as possible.
- Fix X86_32 NUMA build errors that previous version of this
patch caused.
V2->V3:
- add early_cpu_to_node function to keep cpu_to_node efficient
- move and rename smp_set_apicids() to setup_percpu_maps()
- call setup_percpu_maps() as early as possible
V1->V2:
- Removed extraneous casts
- Fix !NUMA builds with '#ifdef CONFIG_NUMA"
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There are already various options to disable specific cpuid bits
on the command line. They all use their own variable. Add a generic
mask to make this easier in the future.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add .set_pgd field to pv_mmu_ops.
Implement pud_val(), __pud(), set_pgd(), pud_clear(), pgd_clear().
pud_clear() and pgd_clear() are implemented simply using set_pud()
and set_pmd(). They don't have a field at pv_mmu_ops.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
__pmd, pmd_val and set_pud are used before they are defined (as static)
We move them a little up in the file, so it doesn't happen.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the cr8 manipulation functions ended up staying in the tree,
they can't be defined just when PARAVIRT is off: In this patch,
those functions are defined for the PARAVIRT case too.
[ mingo@elte.hu: fixes ]
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds room for read and write_cr8 functions back in
pv_cpu_ops struct
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With PARAVIRT, we actually have arch_{dup,exit}_mmap functions,
so we can't include the generic header
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86_64 lacks a native_init_IRQ() function, so we turn the arch's
init_IRQ() function into a native construct
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On some machines, buggy BIOSes don't properly setup WB MTRRs to cover all
available RAM, meaning the last few megs (or even gigs) of memory will be
marked uncached. Since Linux tends to allocate from high memory addresses
first, this causes the machine to be unusably slow as soon as the kernel
starts really using memory (i.e. right around init time).
This patch works around the problem by scanning the MTRRs at boot and
figuring out whether the current end_pfn value (setup by early e820 code)
goes beyond the highest WB MTRR range, and if so, trimming it to match. A
fairly obnoxious KERN_WARNING is printed too, letting the user know that
not all of their memory is available due to a likely BIOS bug.
Something similar could be done on i386 if needed, but the boot ordering
would be slightly different, since the MTRR code on i386 depends on the
boot_cpu_data structure being setup.
This patch fixes a bug in the last patch that caused the code to run on
non-Intel machines (AMD machines apparently don't need it and it's untested
on other non-Intel machines, so best keep it off).
Further enhancements and fixes from:
Yinghai Lu <Yinghai.Lu@Sun.COM>
Andi Kleen <ak@suse.de>
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
They now look like:
hal-resmgr[13791]: segfault at 3c rip 2b9c8caec182 rsp 7fff1e825d30 error 4 in libacl.so.1.1.0[2b9c8caea000+6000]
This makes it easier to pinpoint bugs to specific libraries.
And printing the offset into a mapping also always allows to find the
correct fault point in a library even with randomized mappings. Previously
there was no way to actually find the correct code address inside
the randomized mapping.
Relies on earlier patch to shorten the printk formats.
They are often now longer than 80 characters, but I think that's worth it.
[includes fix from Eric Dumazet to check d_path error value]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On VMs implemented using JITs that cache translated code changing the lock
prefixes is a quite costly operation that forces the JIT to throw away and
retranslate a lot of code.
Previously a SMP kernel would rewrite the locks once for each CPU which
is quite unnecessary. This patch changes the code to never switch at boot in
the normal case (SMP kernel booting with >1 CPU) or only once for SMP kernel
on UP.
This makes a significant difference in boot up performance on AMD SimNow!
Also I expect it to be a little faster on native systems too because a smp
switch does a lot of text_poke()s which each synchronize the pipeline.
v1->v2: Rename max_cpus
v1->v2: Fix off by one in UP check (Thomas Gleixner)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On x86-64 there are several memory allocations before bootmem. To avoid
them stomping on each other they used to be all hard coded in bad_area().
Replace this with an array that is filled as needed.
This cleans up the code considerably and allows to expand its use.
Cc: peterz@infradead.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Choose a less generic name for such a special case. Add
a comment explaining the odd use in X86_32.
Change the one user of stack_pointer.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Leave definition of pt_regs in its own section, move all kernel
code to section afterwards, unify prototype definitions, has some
conditional prototypes to make it clear what was only defined in
32 and 64 bit.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unify the definiton of:
v8086_mode
user_mode
user_mode_vm
stack_pointer
instruction_pointer
frame_pointer
in ptrace.h to make it clear where the differences are between
32 and 64 bit. Changes macros to static inlines as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
kdump needs ELF_CORE_COPY_REGS in crash_save_cpu().
This lack of the macro causes the following BUG.
SysRq : Trigger a crashdump
------------[ cut here ]------------
kernel BUG at include/linux/elfcore.h:105!
invalid opcode: 0000 [1] PREEMPT SMP
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is against current x86.git.
The size of the system call table for 32-bit x86 kernels is obtained by
compile-time calculation of the sys_call_table array, not from the value,
which the NR_syscalls macro expands to. This trivial patch removes the
fossil macro.
Manually tested by grepping the x86 files for the "NR_syscalls" string.
No relevant use cases found.
Build-tested using allyesconfig, allnoconfig and a couple of randconfig
instances. All builds successfully finished.
Runtime test performed using a stripped-down Debian-ish config. The system
booted successfully.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
PSE, PGE, XMM, XMM2, and FXSR are defined as required features, and
will be optimized to a constant at compile time. Remove their redundant
definitions.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove duplicate set_pte* operations. PAE still needs to have special
variants of some of these because it can't atomically update a 64-bit
pte, so there's still some duplication.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rearrange the various pagetable mmu_ops to remove duplication.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
WARNING: vmlinux.o(__ksymtab+0x670): Section mismatch: reference to .init.data:x86_cpu_to_node_map_init (between '__ksymtab_x86_cpu_to_node_map_init' and '__ksymtab_node_data')
Cc: Matthew Dobson <colpatch@us.ibm.com>
Cc: Mike Travis <travis@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rather than remove and/or mangle inb_p/outb_p we want to remove the use
of them from inappropriate places. For the PIC/PIT this may eventually
depend on 32/64bitism or similar so start by adding inb/outb_pit and
inb/outb_pic so that we can make them use any scheme we settle on without
disturbing the existing, correct (for ISA), port 0x80 usage. (eg we can
make inb_pit use udelay without messing up inb_p).
Floppy already does this for the fdc. That really only leaves the CMOS as
a core logic item to tackle, and bits of parallel port handling in the
chipset layers.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ENDPROCs() were not used everywhere. Some code used just END() instead,
while other code used nothing. um/sys-i386/checksum.S didn't #include
<linux/linkage.h> . I also got confused because gcc puts the
.type near the ENTRY, while ENDPROC puts it on the opposite end.
Signed off by: John Reiser <jreiser@BitWagon.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
is_prefetch was the last user of get_segment_eip and only on
X86_32. This function returned the faulting instruction's
address and set the upper segment limit.
Instead, use the convert_ip_to_linear helper and rely on
probe_kernel_address to do the segment checks which was
already done everywhere the segment limit was being checked
on X86_32.
Remove get_segment_eip as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename convert_rip_to_linear to convert_ip_to_linear for shared
X86_32|64 use.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change static bios_cpu_apicid array to a per_cpu data variable.
This includes using a static array used during initialization
similar to the way x86_cpu_to_apicid[] is handled.
There is one early use of bios_cpu_apicid in apic_is_clustered_box().
The other reference in cpu_present_to_apicid() is called after
smp_set_apicids() has setup the percpu version of bios_cpu_apicid.
[ mingo@elte.hu: build fix ]
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change the following static arrays sized by NR_CPUS to
per_cpu data variables:
char cpu_to_node_map[NR_CPUS];
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Clean up references to x86_cpu_to_apicid. Removes extraneous
comments and standardizes on "x86_*_early_ptr" for the early
kernel init references.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change the following static arrays sized by NR_CPUS to
per_cpu data variables:
i386_cpu cpu_devices[NR_CPUS];
(And change the struct name to x86_cpu.)
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change the size of node ids from 8 bits to 16 bits to
accomodate more than 256 nodes.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change the size of APICIDs from u8 to u16. This partially
supports the new x2apic mode that will be present on future
processor chips. (Chips actually support 32-bit APICIDs, but that
change is more intrusive. Supporting 16-bit is sufficient for now).
Signed-off-by: Jack Steiner <steiner@sgi.com>
I've included just the partial change from u8 to u16 apicids. The
remaining x2apic changes will be in a separate patch.
In addition, the fake_node_to_pxm_map[] and fake_apicid_to_node[]
tables have been moved from local data to the __initdata section
reducing stack pressure when MAX_NUMNODES and MAX_LOCAL_APIC are
increased in size.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For K8 system: 4G RAM with memory hole remapping enabled, or more than
4G RAM installed.
when try to use kexec second kernel, and the first doesn't include
gart_shutdown. the second kernel could have different aper position than
the first kernel. and second kernel could use that hole as RAM that is
still used by GART set by the first kernel. esp. when try to kexec
2.6.24 with sparse mem enable from previous kernel (from RHEL 5 or SLES
10). the new kernel will use aper by GART (set by first kernel) for
vmemmap. and after new kernel setting one new GART. the position will be
real RAM. the _mapcount set is lost.
Bad page state in process 'swapper'
page:ffffe2000e600020 flags:0x0000000000000000 mapping:0000000000000000 mapcount:1 count:0
Trying to fix it up, but a reboot is needed
Backtrace:
Pid: 0, comm: swapper Not tainted 2.6.24-rc7-smp-gcdf71a10-dirty #13
Call Trace:
[<ffffffff8026401f>] bad_page+0x63/0x8d
[<ffffffff80264169>] __free_pages_ok+0x7c/0x2a5
[<ffffffff80ba75d1>] free_all_bootmem_core+0xd0/0x198
[<ffffffff80ba3a42>] numa_free_all_bootmem+0x3b/0x76
[<ffffffff80ba3461>] mem_init+0x3b/0x152
[<ffffffff80b959d3>] start_kernel+0x236/0x2c2
[<ffffffff80b9511a>] _sinittext+0x11a/0x121
and
[ffffe2000e600000-ffffe2000e7fffff] PMD ->ffff81001c200000 on node 0
phys addr is : 0x1c200000
RHEL 5.1 kernel -53 said:
PCI-DMA: aperture base @ 1c000000 size 65536 KB
new kernel said:
Mapping aperture over 65536 KB of RAM @ 3c000000
So could try to disable that GART if possible.
According to Ingo
> hm, i'm wondering, instead of modifying the GART, why dont we simply
> _detect_ whatever GART settings we have inherited, and propagate that
> into our e820 maps? I.e. if there's inconsistency, then punch that out
> from the memory maps and just dont use that memory.
>
> that way it would not matter whether the GART settings came from a [old
> or crashing] Linux kernel that has not called gart_iommu_shutdown(), or
> whether it's a BIOS that has set up an aperture hole inconsistent with
> the memory map it passed. (or the memory map we _think_ i tried to pass
> us)
>
> it would also be more robust to only read and do a memory map quirk
> based on that, than actively trying to change the GART so early in the
> bootup. Later on we have to re-enable the GART _anyway_ and have to
> punch a hole for it.
>
> and as a bonus, we would have shored up our defenses against crappy
> BIOSes as well.
add e820 modification for gart inconsistent setting.
gart_fix_e820=off could be used to disable e820 fix.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For enhancing the 32 bit EBP based backtracer, I need the capability
for the backtracer to tell it's customer that an entry is either
reliable or unreliable, and the backtrace printing code then needs to
print the unreliable ones slightly different.
This patch adds the basic capability, the next patch will add a user
of this capability.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It's not too pretty, but I found this made the "PANIC: early exception"
messages become much more reliably useful: 1. print the vector number,
2. print the %cs value, 3. handle error-code-pushing vs non-pushing vectors.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Intel VT doesn't like to engage when the protected-mode state isn't
fully initialized. Make life easier for it by initializing LDTR (to
null) and TR (to a dummy hunk of low memory which will never actually
be touched.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The boot GDT entries are common between 32- and 64-bit mode, so move
them to common code instead of having two identical copies.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
get_segment_eip has similarities to convert_rip_to_linear(),
and is used in a similar context. Move get_segment_eip to
step.c to allow easier consolidation.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
introduce the "asmregparm" calling convention: for functions
implemented in assembly with a fixed regparm input parameters
calling convention.
mark the semaphore and rwsem slowpath functions with that.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This implements ticket lock support for more than 255 CPUs on x86. The
code gets switched according to the configured NR_CPUS.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the _PAGE_FOO constants are defined as (1ul << _PAGE_BIT_FOO), they
become unsigned longs. In 32-bit PAE mode, these end up being
implicitly cast to 64-bit types when used to manipulate a pte, and
because they're unsigned the top 32-bits are 0, destroying the upper
bits of the pte.
When _PAGE_FOO constants are given a signed integer type, the cast to
64-bits will sign-extend so that the upper bits are all ones,
preserving the upper pte bits in manipulations.
Explain this in a prominent place.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Put all the defines for mapping pagetable operations to their native
versions (for the non-paravirt case) into one place. Make the
corresponding changes to paravirt.h.
The tricky part here is that when a pagetable entry can't be updated
atomically (ie, 32-bit PAE), we need special handlers for pte_clear,
set_pte_atomic and set_pte_present. However, the other two modes
don't need special handling for these, and can use a common
set_pte(_at) path.
[ mingo@elte.hu: fixes ]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move ZERO_PAGE/empty_zero_page to common place.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
&ptep->pte isn't always an unsigned long *, so cast it to avoid a warning.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make various pte accessors common.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make sure pte_t, whatever its definition, has a pte element with type
pteval_t. This allows common code to access it without needing to be
specifically parameterised on what pagetable mode we're compiling for.
For 32-bit, this means that pte_t becomes a union with "pte" and "{
pte_low, pte_high }" (PAE) or just "pte_low" (non-PAE).
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on:
Subject: x86: unify pgtable accessors which use supported_pte_mask
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make users of supported_pte_mask common. This has the side-effect of
introducing the variable for 32-bit non-PAE, but I think its a pretty
small cost to simplify the code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In 32-bit PAE, mask NX from pte_pfn, since it isn't part of the PFN.
This code is due for unification anyway, but this fixes a latent bug.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unify functions to test and set bits in pagetable entries.
NOP: only moves existing code around, without any change to it.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
add new ops to 32-bit.
based on:
Subject: x86/pgtable: unify pagetable accessors
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
change the pte_mk inlines to the unified format. Non-NOP!
based on:
Subject: x86/pgtable: unify pagetable accessors
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
change the pte_dirty/* inlines to the unified format. Non-NOP!
based on:
Subject: x86/pgtable: unify pagetable accessors
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on:
Subject: x86/pgtable: unify pagetable accessors
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on:
Subject: x86/pgtable: fix constant sign extension problem
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
32 and 64-bit use the same flags for pagetable entries, so make them all common.
[ mingo@elte.hu: fixes ]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
add PWT bit to NOCACHE flags. No real difference to CPUs, but needed
later for PAT.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Return the size of bts_struct in the PTRACE_BTS_STATUS command.
Change types to u32.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Here is a quick and naive smoke test for kprobes. This is intended to
just verify if some unrelated change broke the *probes subsystem. It is
self contained, architecture agnostic and isn't of any great use by itself.
This needs to be built in the kernel and runs a basic set of tests to
verify if kprobes, jprobes and kretprobes run fine on the kernel. In case
of an error, it'll print out a message with a "BUG" prefix.
This is a start; we intend to add more tests to this bucket over time.
Thanks to Jim Keniston and Masami Hiramatsu for comments and suggestions.
Tested on x86 (32/64) and powerpc.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Form a single percpu.h from percpu_32.h and percpu_64.h. Both are now pretty
small so this is simply adding them together.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86_64 provides an optimized way to determine the local per cpu area
offset through the pda and determines the base by accessing a remote
pda.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86_32 only provides a special way to obtain the local per cpu area offset
via x86_read_percpu. Otherwise it can fully use the generic handling.
Cc: ak@suse.de
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- add support for PER_CPU_ATTRIBUTES
- fix generic smp percpu_modcopy to use per_cpu_offset() macro.
Add the ability to use generic/percpu even if the arch needs to override
several aspects of its operations. This will enable the use of generic
percpu.h for all arches.
An arch may define:
__per_cpu_offset Do not use the generic pointer array. Arch must
define per_cpu_offset(cpu) (used by x86_64, s390).
__my_cpu_offset Can be defined to provide an optimized way to determine
the offset for variables of the currently executing
processor. Used by ia64, x86_64, x86_32, sparc64, s/390.
SHIFT_PTR(ptr, offset) If an arch defines it then special handling
of pointer arithmentic may be implemented. Used
by s/390.
(Some of these special percpu arch implementations may be later consolidated
so that there are less cases to deal with.)
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- Special consideration for IA64: Add the ability to specify
arch specific per cpu flags
- remove .data.percpu attribute from DEFINE_PER_CPU for non-smp case.
The arch definitions are all the same. So move them into linux/percpu.h.
We cannot move DECLARE_PER_CPU since some include files just include
asm/percpu.h to avoid include recursion problems.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The use of the __GENERIC_PERCPU is a bit problematic since arches
may want to run their own percpu setup while using the generic
percpu definitions. Replace it through a kconfig variable.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
reboot_{32|64}.c unification patch.
This patch unifies the code from the reboot_32.c and reboot_64.c files.
It has been tested in computers with X86_32 and X86_64 kernels and it
looks like all reboot modes work fine (EFI restart system hasn't been
tested yet).
Probably I made some mistakes (like I usually do) so I hope
we can identify and fix them soon.
Signed-off-by: Miguel Boton <mboton@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A quick grep shows that there are currently 1145 instances of WARN_ON
in the kernel. Currently, WARN_ON is pretty much entirely inlined,
which makes it hard to enhance it without growing the size of the kernel
(and getting Andrew unhappy).
This patch build on top of Olof's patch that introduces __WARN,
and places the slowpath out of line. It also uses Ingo's suggestion
to not use __FUNCTION__ but to use kallsyms to do the lookup;
this saves a ton of extra space since gcc doesn't need to store the function
string twice now:
3936367 833603 624736 5394706 525112 vmlinux.before
3917508 833603 624736 5375847 520767 vmlinux-slowpath
15Kb savings...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Olof Johansson <olof@lixom.net>
Acked-by: Matt Meckall <mpm@selenic.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Introduce __WARN() in the generic case, so the generic WARN_ON()
can use arch-specific code for when the condition is true.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
# HG changeset patch
# User Jeremy Fitzhardinge <jeremy@xensource.com>
# Date 1199321648 28800
# Node ID 22f6a5902285b58bfc1fbbd9e183498c9017bd78
# Parent bba9287641ff90e836d090d80b5c0a846aab7162
x86: page.h: move things back to their own files
Oops, asm/page.h has turned into an #ifdef hellhole. Move
32/64-specific things back to their own headers to make it somewhat
comprehensible...
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
# HG changeset patch
# User Jeremy Fitzhardinge <jeremy@xensource.com>
# Date 1199319657 28800
# Node ID bba9287641ff90e836d090d80b5c0a846aab7162
# Parent d617b72a0cc9d14bde2087d065c36d4ed3265761
x86: page.h: move remaining bits and pieces
Move the remaining odds and ends into page.h.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
# HG changeset patch
# User Jeremy Fitzhardinge <jeremy@xensource.com>
# Date 1199319656 28800
# Node ID d617b72a0cc9d14bde2087d065c36d4ed3265761
# Parent 3bd7db6e85e66e7f3362874802df26a82fcb2d92
x86: page.h: move pa and va related things
Move and unify the virtual<->physical address space conversion
functions.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on:
Subject: x86: page.h: move and unify types for pagetable entry
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
# HG changeset patch
# User Jeremy Fitzhardinge <jeremy@xensource.com>
# Date 1199319654 28800
# Node ID 3bd7db6e85e66e7f3362874802df26a82fcb2d92
# Parent f7e7db3facd9406545103164f9be8f9ba1a2b549
x86: page.h: move and unify types for pagetable entry definitions
This patch:
1. Defines arch-specific types for the contents of a pagetable entry.
That is, 32-bit entries for 32-bit non-PAE, and 64-bit entries for
32-bit PAE and 64-bit. However, even though the latter two are the
same size, they're defined with different types in order to retain
compatibility with printk format strings, etc.
2. Defines arch-specific pte_t. This is different because 32-bit PAE
defines it in two halves, whereas 32-bit PAE and 64-bit define it as a
single entry. All the other pagetable levels can be defined in a
common way. This also defines arch-specific pte_val/make_pte functions.
3. Define PAGETABLE_LEVELS for each architecture variation, for later use.
4. Define common pagetable entry accessors in a paravirt-compatible
way. (64-bit does not yet use paravirt-ops in any way).
5. Convert a few instances of using a *_val() as an lvalue where it is
no longer a macro. There are still places in the 64-bit code which
use pte_val() as an lvalue.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on:
Subject: x86: page.h: move and unify types for pagetable entry
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on:
Subject: x86: page.h: move and unify types for pagetable entry
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on:
Subject: x86: page.h: move and unify types for pagetable entry
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on:
Subject: x86: page.h: move and unify types for pagetable entry
From: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
# HG changeset patch
# User Jeremy Fitzhardinge <jeremy@xensource.com>
# Date 1199317452 28800
# Node ID f7e7db3facd9406545103164f9be8f9ba1a2b549
# Parent 4d9a413a0f4c1d98dbea704f0366457b5117045d
x86: add _AT() macro to conditionally cast
Define _AT(type, value) to conditionally cast a value when compiling C
code, but not when used in assembler.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
# HG changeset patch
# User Jeremy Fitzhardinge <jeremy@xensource.com>
# Date 1199317362 28800
# Node ID 4d9a413a0f4c1d98dbea704f0366457b5117045d
# Parent ba0ec40a50a7aef1a3153cea124c35e261f5a2df
x86: page.h: unify page copying and clearing
Move, and to some extent unify, the various page copying and clearing
functions. The only unification here is that both architectures use
the same function for copying/clearing user and kernel pages.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
# HG changeset patch
# User Jeremy Fitzhardinge <jeremy@xensource.com>
# Date 1199317360 28800
# Node ID ba0ec40a50a7aef1a3153cea124c35e261f5a2df
# Parent c45c263179cb78284b6b869c574457df088027d1
x86: page.h: unify constants
There are many constants which are shared by 32 and 64-bit.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
we need to know whether RDTSC is synchronous or not.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
rdtsc is now speculation-safe, so no need for the sync variants of
the APIs.
[ mingo@elte.hu: removed the nsec_barrier() complication. ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
map vsyscalls early enough. This is important if a __vsyscall_fn
function is used by other kernel code too.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
rdtsc_barrier() is a new barrier primitive that stops RDTSC speculation
to avoid races with timer interrupts on other CPUs.
It expands either to LFENCE (for Intel CPUs) or MFENCE (for
AMD CPUs) which stops RDTSC on all currently known microarchitectures
that implement SSE. On CPUs without SSE there is generally no RDTSC
speculation.
[ mingo@elte.hu: renamed it to rdtsc_barrier() and made it x86-only ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Moving things out of processor.h is always a good thing.
Also needed to avoid include loop in later patch.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
According to Intel RDTSC can be always synchronized with LFENCE
on all current CPUs. Implement the necessary CPUID bit for that.
It is unclear yet if that is true for all future CPUs too,
but if there's another way the kernel can be always updated.
Cc: asit.k.mallick@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
According to AMD RDTSC can be synchronized through MFENCE.
Implement the necessary CPUID bit for that.
Cc: andreas.herrmann3@amd.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core patching code for paravirt is sufficiently different
among i386 and x86_64, and we move them to specific files.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86_64 needs a potentially larger clobber list than i386, due to its calling
convention. So we add more CLBR_ defines for it.
Note that CLBR_ANY is different for each of the architectures, since it comprises
the notion of "All call clobbers in this architecture"
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the advent of ticket locking, CLI_STRING, STI_STRING, and friends
are not used anymore. They can now be safely deleted.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds paravirt hook for swapgs operation, which is a privileged
operation in x86_64.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
i386 has a macro GET_CR0_INTO_EAX, used in early trap handling code.
x86_64 has similar needs, only it needs to put cr2 into rcx. We provide
a macro for such task, in the same way
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch changes the irq handling function definitions
in paravirt.h (like raw_local_irq_disable) to accomodate for x86_64.
The differences are in the calling convention.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adjust the paravirt macros used in assembly code
to accomodate for x86_64 as well.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To account for differences in x86_64, we change the macros that
create raw instances of the paravirt_patch_site struct.
We need to align 64-pointers to 64-bit boundaries, so we add an alignment
directive. Also, we need to make room for a word-sized pointer,
instead of a fixed 32-bit one
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds a field in pv_cpu_ops for a paravirtualized hook
for rdtscp, needed for x86_64.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
write_tsc() does not need to be enclosed in any paravirt closure,
as it uses wrmsr(). So we rip off the duplicate in msr.h
and the definition from paravirt.h
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adjust the PVOP_VCALL and PVOP_CALL macros to
work with x86_64. It has a different calling convention, and
we use auxiliary macros to account for both calling conventions
as cleanly as possible
Comments are adjusted accordingly.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Establish the user API for sending a user-defined signal to the traced task on a BTS buffer overflow.
This should complete the user API for the BTS ptrace extension.
The patches so far implement wrap-around overflow handling as is needed for debugging.
The remaining open is another overflow handling mechanism that sends a signal to the traced task on a buffer overflow.
This will take some more time from my side.
Since, from a user perspective, this occurs behind the scenes, the patch set should already be useful. More features may/will be added on top of it (overflow signal, pageable back-up buffers, kernel tracing, core file support, profiling, ...).
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pass the buffer size for (most) ptrace commands that pass user-allocated buffers and check that size before accessing the buffer. Unfortunately, PTRACE_BTS_GET already uses all 4 parameters.
Commands that access user buffers return the number of bytes or records read or written.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Support BTS recording of 32bit and 64bit tasks from 32bit or 64bit tasks.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Aviod TLB flush IPIs during C3 states by voluntary leave_mm()
before entering C3.
The performance impact of TLB flush on C3 should not be significant with
respect to C3 wakeup latency. Also, CPUs tend to flush TLB in hardware while in
C3 anyways.
On a 8 logical CPU system, running make -j2, the number of tlbflush IPIs goes
down from 40 per second to ~ 0. Total number of interrupts during the run
of this workload was ~1200 per second, which makes it ~3% savings in wakeups.
There was no measurable performance or power impact however.
[ akpm@linux-foundation.org: symbol export fixes. ]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
dmi_alloc() for CONFIG_X86_64 is defined to allocate from a static array
and it maintains a allocation index which is advanced each time allocation
is attempted - it gets incremented even if an allocation fails thereby
depriving any future request that may be small enough to be satisfied from
the array.
Fix this by first testing if allocation is going to be possible and
incrementing alloc index only then.
Signed-off-by: Parag Warudkar <parag.warudkar@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
What's left in processor_32.h and processor_64.h cannot be cleanly
integrated. However, it's just a couple of definitions. They are moved
to processor.h around ifdefs, and the original files are deleted. Note that
there's much less headers included in the final version.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch removes the __init modifier from an extern function
declaration in acpi.h.
Besides not being strictly needed, it requires the inclusion of
linux/init.h, which is usually not even included directly, increasing
header mess by a lot.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This makes ELF core dumps of 32-bit processes include a new
note type NT_386_TLS (0x200) giving the contents of the TLS
slots in struct user_desc format. This lets post mortem
examination figure out what the segment registers mean like
the debugger does with get_thread_area on a live process.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This switches x86-64's 32-bit ELF support to use the shared
fs/compat_binfmt_elf.c code instead of our own ia32_binfmt.c.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This removes a bunch of dead code that is no longer needed now
that the user_regset interfaces are being used for all these jobs.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This switches x86 to the user_regset-based code for ELF core dumps.
The core dumps come out exactly the same as before.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This cleans up the TLS code to use struct desc_struct and to separate the
encoding and installation magic from the interface wrappers.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This removes all the old code that is no longer used after
the i387 unification and cleanup. The i387_64.h is renamed
to i387.h with no changes, but since it replaces the nonempty
one-line stub i387.h it looks like a big diff and not a rename.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This revamps the i387 code to be shared across 32-bit, 64-bit,
and 32-on-64. It does so by consolidating the code in one place
based on the user_regset accessor interfaces. This switches
32-bit to using the i387_64.h header and 64-bit to using the
i387.c that was previously i387_32.c, but that's what took the
least cleanup in each file. Here i387.h is stubbed to always
include i387_64.h rather than renaming the file, to keep this
diff smaller and easier to read.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This moves some code into asm-x86/i387_64.h in preparation for
unifying this code between 32 and 64. The 32-bit versions of
some things are copied in some existing names changed to match
32-bit names and share code. For 64, save_i387 is moved into
an inline from i387_64.c; this matches restore_i387, which is
already an inline, and makes sense since there is exactly one
caller (in signal_64.c). The save_i387 function could use more
cosmetic cleanup, but it is just moved verbatim in this patch.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The i387_fxsave_struct formats really have the same layout
on 32 and 64, with only some slightly different use of a few
fields. The i387_fsave_struct and i387_soft_struct formats
are never used by 64-bit kernels, but it doesn't hurt to
have the unused types in the union and cuts down on the
amount of #ifdef hair required throughout the i387 code.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>