Commit Graph

195985 Commits

Author SHA1 Message Date
Ivo van Doorn
4e9e58c6bf rt2x00: Fix compile warning when debug disabled
CC [M]  drivers/net/wireless/rt2x00/rt2800lib.o
drivers/net/wireless/rt2x00/rt2800lib.c: In function 'rt2800_ampdu_action':
drivers/net/wireless/rt2x00/rt2800lib.c:2821: warning: unused variable 'rt2x00dev'

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:53 -04:00
Ivo van Doorn
efc7d36f0d rt2x00: Always set BBP_CSR_CFG_BBP_RW_MODE to 1
Latest rt2870 legacy driver also sets BBP_CSR_CFG_BBP_RW_MODE to 1
when reading or writing the EEPROM. This means we can make the
BBP reading and writing completely equal on all platforms.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:53 -04:00
Ivo van Doorn
e22557f2e3 rt2x00: Fix antenna initialization
Legacy driver indicates that BBP1_TX_ANTENNA must be set
to 0 for TXPATH values of 1 and 3. So the previous statement
that nothing should be done for TXPATH = 3, is false.

Furthermore, remove the false BBP3_RX_ANTENNA initialization
when TXPATH is 1 for PCI and SOC devices. This field will always
be overridden in the next switch statement, making this initialization
bogus. History of this line indicates it was there from the beginning,
and was once caught as typo. Instead of replacing the line with the
correct line, the correct line was added...

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:53 -04:00
Ivo van Doorn
aa674631ef rt2x00: Fix IEEE80211_HT_CAP_RX_STBC assignment
IEEE80211_HT_CAP_RX_STBC is a 2 bit flag, and should thus
never be set as normal flag. Instead we must read the number
of RX paths from the EEPROM and set the IEEE80211_HT_CAP_RX_STBC
with the correct value (using the same logic as the number of TX
streams).

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:52 -04:00
Helmut Schaa
fdb8725122 rt2x00: fix beacon reset on rt2800
When an interface is removed the according beacon entry should be reset.
The current approach to only clear the first word is not enough to stop
the device from sending out the beacon, hence resulting in beacons being
sent out for already removed interfaces.

Fix this by invalidating the entire TXWI in front of the beacon instead
of only the first word.

Also clear all beacons during startup in the same way.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:52 -04:00
Helmut Schaa
8654b79f9c rt2x00: Disable link tuning in AP mode
Since the link tuning is based on average RSSI values taken from all received
frames it doesn't make sense to enable it in AP mode where every associated
station provides independent RSSI values. Furthermore the legacy drivers
don't enable link tuning in AP mode as well.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:52 -04:00
Helmut Schaa
fa43750f00 rt2x00: Fix beacon updates in rt61pci
Fix rt61pci beacon updates in the same way as rt2800pci. rt61pci didn't
update the beacon template after each beacon interval, resulting in the
DTIM count being incorrect (if DTIM period > 1). Fix this by calling
rt2x00lib_beacondone after the current beacon was sent out.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:52 -04:00
Helmut Schaa
ad90319bc3 rt2x00: Fix beacon updates in rt2800pci
rt2800pci didn't update the beacon template after each beacon interval,
resulting in the DTIM count being incorrect (if DTIM period > 1). Fix this
by calling rt2x00lib_beacondone after the current beacon was sent out.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:52 -04:00
Ivo van Doorn
d440cb9eb1 rt2x00: Enable multiBSS in rt2800
MAC_BSSID_DW1_BSS_ID_MASK must be set to the mask 3, to
enable 8 BSSID's. The MAC_BSSID_DW1_BSS_BCN_NUM is initialized
to 7 to enable the 8 beacons.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:52 -04:00
Gertjan van Wingerde
ec2d1791a0 rt2x00: Align rt2800 EEPROM validation to Ralink vendor driver.
Align with the latest versions of the Ralink legacy driver(s).

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:51 -04:00
Gertjan van Wingerde
20f8b139a3 rt2x00: Correctly detect 93C86 EEPROMs in rt2800pci.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:51 -04:00
Gertjan van Wingerde
afd2a5ca1e eeprom_93cx6: Add support for 93c86 EEPROMs.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:50 -04:00
Gertjan van Wingerde
9cf4cb05c9 rt2x00: Split of TXWI writing to write_tx_data callback in rt2800usb.
Align with the way PCI devices are handled, even though it is not
strictly necessary.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:50 -04:00
Gertjan van Wingerde
76dd5ddf23 rt2x00: Rename driver write_tx_datadesc callback function.
Now that the {usb,pci} specific write_tx_data functions are no longer
present we can rename the write_tx_datadesc callback function back to
its old name.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:50 -04:00
Gertjan van Wingerde
e513a0b6f1 rt2x00: Move common txdone handling to rt2x00lib_txdone.
Now that the write_tx_data functions are merged, also merge the relevant
parts of the txdone handling into common code, rather than {usb,pci}
specific code.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:50 -04:00
Gertjan van Wingerde
78eea11b0e rt2x00: Merge PCI and USB versions of write_tx_data into single function.
Now that rt2x00pci_write_tx_data and rt2x00usb_write_tx_data are similar
we can merge them in a single function in rt2x00queue.c.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:50 -04:00
Gertjan van Wingerde
fe7256971f rt2x00: Move filling of TX URB to rt2x00usb_kick_tx_entry function.
There is no need to fill the TX URB this early, and moving it to the
rt2x00usb_kick_tx_entry function allows us to merge the PCI and USB
variants of the write_tx_data function.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:49 -04:00
Gertjan van Wingerde
398ab9ea74 rt2x00: Fix frame dumping for USB devices.
We forgot to clear the SKBDESC_DESC_IN_SKB when the descriptor was removed
from the front of the skb.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:49 -04:00
Ivo van Doorn
1ed7a17a8e rt2x00: Remove unneeded variable
The update_bssid is set only when BSS_CHANGED_BSSID is used,
but the check if that field is true is done later in the function
but also only when BSS_CHANGED_BSSID is set. This makes the
variable useless, as it can never result in a negative check.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:49 -04:00
Ivo van Doorn
f1aa4c541e rt2x00: Write the BSSID to register when interface is added
For the Master mode case, we initialized the BSSID as the MAC
address, but never wrote it into the registers. This causes
Hardware crypto to break in Master mode when receiving frames
which require the BSSID to be filled in.

This is safe for STA mode since the BSSID will be initialized
to 00:00:00:00:00 at this point, but will be set to the correct
value later when the device associates.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:49 -04:00
Helmut Schaa
1df90809f7 rt2x00: Implement tx mpdu aggregation
In order to implement tx mpdu aggregation we only have to implement
the ampdu_action callback such that mac80211 allows negotiation of
blockack sessions.

The hardware will handle everything on its own as long as the ampdu
flag in the TXWI struct is set up correctly and we translate the tx
status correctly.

For now, refuse requests to start rx aggregation.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-30 15:00:48 -04:00
John W. Linville
f35376a44f ath9k: make ath9k_hw_keysetmac static
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-29 15:24:05 -04:00
John W. Linville
99aeed9cde ath9k: remove unused function ath9k_hw_keyisvalid
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-29 15:20:49 -04:00
John W. Linville
c466d4efb8 mac80211: add basic tracing to drv_get_survey
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-29 14:51:23 -04:00
John W. Linville
ff3074a4dd mac80211: remove unnecessary check in ieee80211_dump_survey
This check is duplicated in drv_get_survey.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-29 13:55:04 -04:00
Felix Fietkau
38bdb650f9 mac80211: fix the for_each_sta_info macro
Because of an ambiguity in the for_each_sta_info macro, it can
currently only be used if the third parameter is set to 'sta'.
Fix this by renaming the parameter to '_sta'.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-28 15:16:20 -04:00
Felix Fietkau
78c4653a22 ath9k: fix retry count for A-MPDU rate control status reports
The 'bf_retries' field of the ath_buf structure was used for both
software retries (AMPDU subframes) and hardware retries (legacy
frames). This led to a wrong retry count being reported for the A-MPDU
rate control stats.
This patch changes the code to no longer use bf_retries for reporting
retry counts, but instead always using the real on-chip retry count
from the ath_tx_status.
Additionally, if the first subframe of an A-MPDU was not acked, the tx
status report is submitted along with the first acked subframe, which
may not contain the correct rates in the tx info.
This is easily corrected by saving the tx rate info before looping over
subframes, and then copying it back once the A-MPDU status report is
submitted.
In my tests this change improves throughput visibly.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-28 15:16:19 -04:00
Bruno Randolf
6665b54e79 ath5k: fix antenna div gc for <= AR5K_SREV_PHY_2413
In commit 39d5b2c83c "ath5k: update
AR5K_PHY_RESTART_DIV_GC values to match masks" i introduced a regression on PHY
chips older than AR5K_SREV_PHY_5413, which caused signal values to be about
10dB less that before. This patch reverts the AR5K_PHY_RESTART_DIV_GC values to
the same values which were effectively used before (without the bitmask
mistake). This brings signal levels back to normal on these PHY chips.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-28 15:16:19 -04:00
Magnus Damm
55d02a47de b43: Add SDIO_DEVICE() for EW-CG1102GC
This patch enables the EW-CG1102GC SDIO card in the b43 driver.

b43-sdio mmc0:0001:1: Chip ID 14e4:4318
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
b43-phy0 debug: Found PHY: Analog 3, Type 2, Revision 7
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 8

Tested with openfwwf-5.2 using a SuperH SDHI host controller.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-28 15:16:19 -04:00
John W. Linville
5ed3bc7288 mac80211: use netif_receive_skb in ieee80211_tx_status callpath
This avoids the extra queueing from calling netif_rx.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-28 15:14:51 -04:00
John W. Linville
5548a8a113 mac80211: use netif_receive_skb in ieee80211_rx callpath
This avoids the extra queueing from calling netif_rx.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-28 15:14:51 -04:00
Wey-Yi Guy
679db79467 iwlwifi: add disable rf calibration support for 6000g2a and 6000g2b
Radio calibration (chain noise and sensitivity) should be allowed to
be disabled from debugfs if compiled with CONFIG_IWLWIFI_DEBUGFS. For both
6000g2a and 6000g2b, the parameters are missing in "cfg", which cause
user can not disable the radio calibration manually; add the support to
allow the operation.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 15:20:41 -07:00
Reinette Chatre
2b2129f159 iwlagn: reduce severity of disconnected antennas warning
This message is encountered regularly and we need to take a closer look at
the circumstances under which it is printed before presenting errors to
users.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 15:20:41 -07:00
Wey-Yi Guy
cfecc6b492 iwlwifi: turn on RTS/CTS after aggregation become operational
If RTS/CTS protection is needed for HT, wait until get operational
notification from mac80211, then inform uCode to switch to RTS/CTS
through RXON command.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 15:20:41 -07:00
Johannes Berg
0ab84cff8b iwlwifi: read rfkill during resume
When resuming from hibernate or suspend,
the status of the rfkill switch isn't
known since it might have been toggled
while the system was asleep. Therefore,
we need to read out the status at resume
time to make sure the system knows about
an up-to-date status.

Reported-by: Mark Tung <mark.y.tung@intel.com>
Tested-by: Mark Tung <mark.y.tung@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 15:20:18 -07:00
Daniel Halperin
278c2f6faa iwlwifi: update LQ for bcast station on channel change
The rate table in the bcast LQ is computed only when the station is
allocated, and chooses the lowest rate for the band. Because of when this
occurs, this is the 2.4 GHz band and uses the 0x420a (CCK, 1 Mbps) rate. In 5 GHz
beaconing mode, this rate will prevent beacons from being sent and any other
packets from being received.

We can fix this by re-initializing the bcast station's LQ command when the
channel is changed.

Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:53:49 -07:00
Wey-Yi Guy
680788aca3 iwlwifi: add a mechanism to disable plcp error checking
For some devices, especially the upcoming new devices, the plcp error
rate is different. Before the correct error rate can be determine, also
for the debugging purpose; add the mechanism to disable plcp error checking
which cause radio reset happen.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:52:47 -07:00
Wey-Yi Guy
178d159607 iwlwifi: enable DC calibration based on config parameter
Different devices have different calibration requirement,
some need DC calibration and some don't; make it a cfg parameter
for easy management.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:52:18 -07:00
Wey-Yi Guy
4e3243f549 iwlwifi: name change from signal protection flag
This bit need to be set for both RTS/CTS or CTS-to-self protection, if
CTS-to-self is used, then uCode will  check the RXON_FLG_SELF_CTS_EN
status. Change the name from TX_CMD_FLG_RTS_CTS_MSK to TX_CMD_FLAG_PROT_REQUIRE_MSK
to match the behavior of the bit setting.

Also update comments to reflect which hardware uses which of the TX command
flags.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:50:53 -07:00
Reinette Chatre
e691e19e05 Merge branch 'wireless-2.6' into wireless-next-2.6 2010-06-25 14:47:02 -07:00
Wey-Yi Guy
062bee448b iwlwifi: set TX_CMD_FLAG_PROT_REQUIRE_MSK in tx_flag
When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK
for 5000 series and up.

Without setting this bit the firmware will not examine the RTS/CTS setting
and thus not send traffic with the appropriate protection. RTS/CTS is is
required for HT traffic in a noisy environment where, without this setting,
connections will stall on some hardware as documented in the patch that
initially attempted to address this:

    commit 1152dcc28c
    Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
    Date:   Fri Jan 15 13:42:58 2010 -0800

    iwlwifi: Fix throughput stall issue in HT mode for 5000

    Similar to 6000 and 1000 series, RTS/CTS is the recommended
    protection mechanism for 5000 series in HT mode based on the HW design.
    Using RTS/CTS will better protect the inner exchange from interference,
    especially in highly-congested environment, it also prevent uCode encounter
    TX FIFO underrun and other HT mode related performance issues.

For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self
protection.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 14:34:45 -07:00
Johannes Berg
d1e89f37de iwlwifi: fix multicast
commit 3474ad635d
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Thu Apr 29 04:43:05 2010 -0700

    iwlwifi: apply filter flags directly

broke multicast. The reason, it turns out, is that
the code previously checked if ALLMULTI _changed_,
which the new code no longer did, and normally it
_never_ changes. Had somebody changed it manually,
the code prior to my patch there would have been
broken already.

The reason is that we always, unconditionally, ask
the device to pass up all multicast frames, but the
new code made it depend on ALLMULTI which broke it
since now we'd pass up multicast frames depending
on the default filter in the device, which isn't
necessarily what we want (since we don't program it
right now).

Fix this by simply not checking allmulti as we have
allmulti behaviour enabled already anyway.

Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-06-25 14:32:06 -07:00
Vasanthakumar Thiagarajan
47399f1a7d ath9k: Wakeup the chip in an appropriate place in ath_paprd_calibrate()
Move ath9k_ps_wakeup() down just before accessing hw registers.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:43 -04:00
Vasanthakumar Thiagarajan
78a1817251 ath9k: Remove unused paprd_txok
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:42 -04:00
Vasanthakumar Thiagarajan
ca369eb494 ath9k: Fix bug in paprd
It is possbile that the transmission of paprd test frame
might not get completed in 100ms if tx is stuck. Freeing
this skb upon timeout in ath_paprd_calibrate() will result
in accessing already freed memory when the associated pending
buffer is drained in txq. This patch fixes this issue.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:39 -04:00
Ondrej Zary
75f64dd54a rt2500usb: fallback to SW encryption for TKIP+AES
HW crypto in rt2500usb does not seem to support keys with different ciphers,
which breaks TKIP+AES mode. Fall back to software encryption to fix it.

This should fix long-standing problems with rt2500usb and WPA, such as:
http://rt2x00.serialmonkey.com/phpBB/viewtopic.php?f=4&t=4834
https://bugzilla.redhat.com/show_bug.cgi?id=484888

Also tested that it does not break WEP, TKIP-only and AES-only modes.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:38 -04:00
Juuso Oikarinen
98d2ff8bec nl80211: Add option to adjust transmit power
This patch adds transmit power setting type and transmit power level attributes
to NL80211_CMD_SET_WIPHY in order to facilitate adjusting of the transmit power
level of the device.

The added attributes allow selection of automatic, limited or fixed transmit
power level, with the level definable in signed mBm format.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:37 -04:00
Juuso Oikarinen
fa61cf70a6 cfg80211/mac80211: Update set_tx_power to use mBm instead of dBm units
In preparation for a TX power setting interface in the nl80211, change the
.set_tx_power function to use mBm units instead of dBm for greater accuracy and
smaller power levels.

Also, already in advance move the tx_power_setting enumeration to nl80211.

This change affects the .tx_set_power function prototype. As a result, the
corresponding changes are needed to modules using it. These are mac80211,
iwmc3200wifi and rndis_wlan.

Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:33 -04:00
Sebastian Smolorz
a185045c8d at76c50x-usb: Extract bssid from authentication frame
The driver at76c50x-usb is unable to authenticate with an AP since
kernel 2.6.31 for the following reason: The join command of the firmware
needs to be sent with the right bssid before any transmission can start.
Before kernel 2.6.31 mac80211 informed its drivers about the changing
bssid early enough for at76c50x-usb but during the development of 2.6.31
mac80211's behaviour changed. Now a new bssid is set after the
association.

This patch changes the tx routine of the driver at76c50x-usb in such a
way that a new bssid is extracted from an authentication frame and the
join command with that bssid is processed.

Signed-off-by: Sebastian Smolorz <sesmo@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:33 -04:00
Sebastian Smolorz
41b4b289ad at76c50x-usb: Move function at76_join() several lines up
This patch does a simple code move of at76_join() so that
at76_mac80211_tx() follows at76_join() in the driver's source file.

This is a preparatory patch for the following patch where we need
to call at76_join() from at76_mac80211_tx() in order to
authenticate successfully with a bssid.

Signed-off-by: Sebastian Smolorz <sesmo@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-24 15:42:32 -04:00