We still need to power up the controller to avoid unsightly self-immolation
should something try to access its registers, but the sensor can stay
powered down unless the camera was actually operating at suspend time.
This gets rid of the camera LED flash on resume, fixing OLPC bug #11644.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is only one frame known to the DMA engine in scatter/gather mode, but
it still tells us that any or all of frames 1-3 are done at each completion
interrupt. Avoid the creation of junk frames by being sure to only
"complete" one on each interrupt.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I had learned through hard experience that dinking around with the DMA
descriptors while the C1_DESC_ENA enable bit was set is a recipe for all
kinds of truly malicious behavior on the hardware's part, regardless of
whether the DMA engine is actually operating at the time. That
notwithstanding, the driver did so dink, resulting in "green frame"
captures and the death of the system in random, spectacular ways.
Move the tweaking of C1_DESC_ENA to the same function that sets the
descriptor so we know that we'll never try to set a descriptor while that
bit is set.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Experience shows that, on the Armada platform, it can take as much as 120ms
for the DMA engine to actually shut down after it has been told to. So a
40ms timeout is not adequate; use 150ms instead. Also make sure we don't
leave the DMA_ACTIVE flag set once things are down.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The marvell cam driver retained just enough of the owner-tracking logic
from cafe_ccic to be broken; it could, conceivably, cause the driver to
release DMA memory while the controller is still active. Simply remove the
remaining pieces and ensure that the controller is stopped before we free
things.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The controller stop/restart logic could possibly restart DMA after the
driver things things have stopped, with suitably ugly results. Make sure
that we only restart the hardware if we're supposed to be streaming.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds clk_prepare/clk_unprepare calls to the pxa_camera
driver by using the helper functions clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer CEU versions, e.g., the one, used on sh7372, support image sizes
larger than 2560x1920. Retrieve maximum sizes from platform properties.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_camera_power_on() calls client's .s_power(1) method, which can try to
access the client hardware. This, however, is typically only possible,
after calling host's .add() method, because that's where the host driver
usually turns the master clock on.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes rc_core to not load the IR decoders at load time,
postponing it to load only if a RC_DRIVER_IR_RAW device is
registered via rc_register_device.
We use a static boolean variable, to ensure decoders modules
are only loaded once.
Tested with rc-loopback device only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove incorrect SEC_MINI_B settings-TODO complete this section.
Correct break and remove return -EINVAL within set tone. It appears
there is a bug that occasionally something other than ON/OFF is
sent stalling the driver. Just continue and write back registers.
Set register b2 in setup. This is the set voltage pin which
isn't used in lmedm04 driver but it is always set to 0x1.
Correct the if statements in set_tuner_rf.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes for previous patch I liked to do.
Just move tuner init and sleep to own functions from the demod
init and sleep functions. Functionality remains still almost the same.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c failures were caused by enabling both i2c gates
at the same time while putting the tuners asleep.
This patch removes the init() and sleep() callbacks from the tuner,
to prevent frontend.c from calling
i2c_gate_ctrl
tuner init / sleep
i2c_gate_ctrl
without holding the lock.
tuner init() and sleep() are instead called in frontend init() and
sleep().
Signed-off-by: Gordon Hecker <ghecker@gmx.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct dvb_usb_device *d can never be NULL so don't waste time
checking for this.
Rationale: the urb's context is set when usb_fill_bulk_urb() is called
in dib0700_rc_setup(), and never changes after that. d is dereferenced
unconditionally in dib0700_rc_setup() so it can't be NULL or the
driver would crash right away.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch saves 255 bytes of stack on usb_probe() by removing
a char array. In some platforms this is represents a substantial save.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The au8522 driver programs the tuner after programming the demodulator,
but the tuner should be programmed first. This patch fixes this behavior.
EDIT: Apparantly Devin created a similar patch some time ago, but hasn't
submitted it for merge. I never saw his patch, but I thank him anyhow
for his efforts. In addition, Devin pointed out a flaw in my patch:
This newly generated patch takes Devin's comments into account.
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Yet another device ID that has started showing up in the wild.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Media-related drivers living outside drivers/media/ (such as the UVC
gadget driver in drivers/usb/gadget/) rely on the media core being
initialized before they're probed. As drivers/usb/ is linked before
drivers/media/, this is currently not the case and will lead to crashes
if the drivers are not compiled as modules.
Register media_devnode_init() as a subsys_initcall() instead of
module_init() to fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MT9M032 is a parallel 1.6MP sensor from Micron controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports cropping, gain,
exposure and v/h flipping controls in monochrome mode with an
external pixel clock.
[Lots of clean up, fixes and enhancements]
Signed-off-by: Martin Hostettler <martin@neutronstar.dyndns.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compute the PLL parameters at runtime using the generic Aptina PLL
helper.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a generic helper function to compute PLL parameters for PLL found in
several Aptina sensors.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fields are set but never used, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Current default value of "nr_tables" option corresponds to the DMA
buffer of about 10 to 48 seconds long, which is obviously too much.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a data integrity check using the sequence counter and
error flags added by the bridge chip.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver started a kthread to poll the DMA buffers soon after probing,
which relsuleted in 1000/sec sleeps and wakeups of the thread doing nothing
useful until someone started feeding.
This patch changes the creation and destruction of the kthread depending on the number of users.
Signed-off-by: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These arrays were embedded in the struct itself, but they weren't
used by anyone, since urbs are now dinamically allocated
at em28xx_usb_isoc_ctl struct.
Tested by compilation only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are couple places where we check unsigned values for negative. I
changed ->gpin_nr to signed because in gpio_ir_recv_probe() we do:
if (pdata->gpio_nr < 0)
return -EINVAL;
I also change gval to a signed int in gpio_ir_recv_irq() because that's
the type that gpio_get_value_cansleep() returns and we test for negative
returns.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix following compilation error when CONFIG_PM_SLEEP is disabled:
CC drivers/media/video/s5p-fimc/mipi-csis.o
drivers/media/video/s5p-fimc/mipi-csis.c: In function ‘s5pcsis_remove’:
drivers/media/video/s5p-fimc/mipi-csis.c:956: error: implicit declaration of function ‘s5pcsis_suspend’
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/w9966.c: In function ‘__check_pardev’:
drivers/media/video/w9966.c:136:1: warning: return from incompatible pointer type [enabled by default]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following build error:
LD .tmp_vmlinux1
drivers/built-in.o: In function `mx2_camera_init_videobuf':
clkdev.c:(.text+0xcfaf4): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `mx2_camera_probe':
clkdev.c:(.devinit.text+0x5734): undefined reference to `vb2_dma_contig_init_ctx'
clkdev.c:(.devinit.text+0x5778): undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `mx2_camera_remove':
clkdev.c:(.devexit.text+0x89c): undefined reference to `vb2_dma_contig_cleanup_ctx'
commit c6a41e3271 ([media] media i.MX27 camera: migrate driver to videobuf2)
missed to select VIDEOBUF2_DMA_CONTIG in Kconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the VIDIOC_G/S_SELECTION ioctls documentation more consistent
with the rest of media Docbook, use capital letters where necessary
and correct few minor errors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a v4l2 bridge driver for Blackfin video capture device, support ppi and eppi interface.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a v4l2 sensor-level driver for the ST VS6624 camera.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is a v4l2 subdevice driver to support Analog Devices ADV7183 SDTV video decoder.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for m88rs2000 module.
The driver also attempts to overcome occasional lock problems.
Call backs are now used for read_status, signal level and SNR.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This field is handled internally by the DVB core, with uses the
selected delivery system to fill it, when a DVBv3 call is
handled. So, drivers should not touch on it.
Cc: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for m88rs2000 chip used in lmedm04 driver.
Note there are still lock problems.
Slow channel change due to the large block of registers sent in set_frontend.
Version 2 differences.
Front end is completely shut down when in sleep mode. This allow user to regain
control of device.
Kaffeine scan problem solved by removing register calls from get_frontend.
Kaffeine seems to call get_frontend when updating signal data. This can happen
in the middle of a tune stalling the driver.
Change calculations to those in the DS3000 driver.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These were in the original lme2510 device driver.
Removing them significantly speeds up the driver.
All tuners tested.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In CDRXD(), Negative number is assigned to unsigned variable
'state->noise_cal.tdCal2.
Members of 'SNoiseCal' should be 'signed short'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DibAcquireLock() is implemented as mutex_lock_interruptible()
but the driver does not handle unsuccessful locking.
As a result it may lead to unlock of an unheld mutex.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several error paths, where &state->platform.risc.mem_mbx_lock
is not unlocked. The patch fixes it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
linux-next:
I like to spend some time reading code, in doing so I have found some
typos in some of the comments.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ryley and me tested several eLNA configuration values with both a rooftop
and a portable antenna.
Ryley fuond out that the best value for his Elgato stick is indeed the current
default value 0xC0.
Instead, my stick is not capable of tuning VHF channels with 0xC0. With 0x80,
VHF works but the tuner sensitivity with the portable antenna is poor.
Instead, the value 0xA0 works with VHF and also gives good performance with
both the rooftop and the portable antenna.
So we concluded that devices built on the reference design work best with 0xA0,
while custom designs (Elgato, PCTV) seem to require 0xC0.
I also removed the unused parameter "minor" in struct as102_dev_t.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Ryley Angus <rangus@student.unimelb.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
