This patch introduces the support for Keymile's kmcoge4 board which is
the internal reference design for boards based on Freescale's
P2040/P2041 SoCs. This internal reference design is named kmp204x.
The peripherals used on this board are:
- SPI NOR Flash as bootloader medium
- NAND Flash with a ubi partition
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 4 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
CPLD
- 2 I2C busses
- last but not least, the mandatory serial port
The patch also adds a defconfig file for this reference design that is
necessary because of the lowmem option that must be set higher due to
the number of PCIe devices with big ioremapped mem ranges on the boad.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
These are the bindings for 2 MFD devices used on some of the Keymile boards.
The first one is the chassis managmenet bfticu FPGA.
The second one is the board controller (reset, LEDs, GPIOs) QRIO CPDL.
These FPGAs are used in the kmcoge4 board.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Even though the company belongs to Microsemi, many chips are still
labeled as Zarlink. Among them is the family of network clock generators,
the zl3034x.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
PCI controller disable PME message report feature, that shouldn't
have happened. Fix it and enable PME message report feature.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
There are error parameters should be corrected when
calling dma_free_coherent to free rmu rx-ring buffers
in fsl_open_inb_mbox() function.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The only way Freescale booke chips support mappings larger than 4K
is via TLB1. The only way we support (direct) TLB1 entries is via
hugetlb, which is not what map_kernel_page() does when given a large
page size.
Without this, a kernel with CONFIG_SPARSEMEM_VMEMMAP enabled crashes on
boot with messages such as:
PID hash table entries: 4096 (order: 3, 32768 bytes)
Sorting __ex_table...
BUG: Bad page state in process swapper pfn:00a2f
page:8000040000023a48 count:0 mapcount:0 mapping:0000040000ffce48 index:0x40000ffbe50
page flags: 0x40000ffda40(active|arch_1|private|private_2|head|tail|swapcache|mappedtodisk|reclaim|swapbacked|unevictable|mlocked)
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags:
page flags: 0x311840(active|private|private_2|swapcache|unevictable|mlocked)
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.15.0-rc1-00003-g7fa250c #299
Call Trace:
[c00000000098ba20] [c000000000008b3c] .show_stack+0x7c/0x1cc (unreliable)
[c00000000098baf0] [c00000000060aa50] .dump_stack+0x88/0xb4
[c00000000098bb70] [c0000000000c0468] .bad_page+0x144/0x1a0
[c00000000098bc10] [c0000000000c0628] .free_pages_prepare+0x164/0x17c
[c00000000098bcc0] [c0000000000c24cc] .free_hot_cold_page+0x48/0x214
[c00000000098bd60] [c00000000086c318] .free_all_bootmem+0x1fc/0x354
[c00000000098be70] [c00000000085da84] .mem_init+0xac/0xdc
[c00000000098bef0] [c0000000008547b0] .start_kernel+0x21c/0x4d4
[c00000000098bf90] [c000000000000448] .start_here_common+0x20/0x58
Signed-off-by: Scott Wood <scottwood@freescale.com>
Several of the error paths from fsl_rio_setup are missing error
messages.
Worse, fsl_rio_setup initializes several global pointers and does not
NULL them out after freeing/unmapping on error. This caused
fsl_rio_mcheck_exception() to crash when accessing rio_regs_win which
was non-NULL but had been unmapped.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Liu Gang <Gang.Liu@freescale.com>
---
Liu Gang, are you sure all of these error conditions are fatal? Why
does the rio driver fail if rmu is not present (e.g. on t4240)?
This series adds support for building the powerpc 64-bit
LE kernel using the new ABI v2. We already supported
running ABI v2 userspace programs but this adds support
for building the kernel itself using the new ABI.
In case of extending the eaddr in future, use this macro
PGTABLE_EADDR_SIZE to ease the maintenance of the code.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds an option to enable a work around for an icache bug on
476 that can cause execution of stale instructions when falling
through pages (IBM errata #46). It requires a recent version of
binutils which supports the --ppc476-workaround option.
The work around enables the appropriate linker options and ensures
that all module output sections are aligned to 4K page boundaries. The
work around is only required when building modules.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PPC476GTR SoC supports message signalled interrupts (MSI) by writing
to special addresses within the High Speed Transfer Assist (HSTA) module.
This patch adds support for PCI MSI with a new system device. The DMA
window is also updated to allow access to the entire 42-bit address range
to allow PCI devices write access to the HSTA module.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support for the IBM Akebono board.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The IBM Akebono code uses the same initialisation functions as the
earlier Currituck board. Rather than create a copy of this code for
Akebono we will instead integrate support for it into the same file as
the Currituck code.
This patch just renames the board support file and updates the Makefile.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we never get around to seeing an HEA ethernet adapter, there's
no point in restricting ourselves to 4k IO page size.
This speeds up IO maps when CONFIG_IBMEBUS is disabled.
[ Updated the test to also lift the restriction on arch 2.07
(Power 8) which cannot have an HEA
-- BenH ]
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
foo
Unaligned stores take alignment exceptions on POWER7 running in little-endian.
This is a dumb little-endian base memcpy that prevents unaligned stores.
Once booted the feature fixup code switches over to the VMX copy loops
(which are already endian safe).
The question is what we do before that switch over. The base 64bit
memcpy takes alignment exceptions on POWER7 so we can't use it as is.
Fixing the causes of alignment exception would slow it down, because
we'd need to ensure all loads and stores are aligned either through
rotate tricks or bytewise loads and stores. Either would be bad for
all other 64bit platforms.
[ I simplified the loop a bit - Anton ]
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we do a treclaim and we are not in TM suspend mode, it results in a TM bad
thing (ie. a 0x700 program check). Similarly if we do a trechkpt and we have
an active transaction or TEXASR Failure Summary (FS) is not set, we also take a
TM bad thing.
This should never happen, but if it does (ie. a kernel bug), the cause is
almost impossible to debug as the GPR state is mostly userspace and hence we
don't get a call chain.
This adds some checks in these cases case a BUG_ON() (in asm) in case we ever
hit these cases. It moves the register saving around to preserve r1 till later
also.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We save r1 to the scratch SPR and restore it from there after the trechkpt so
saving r1 to the paca is not needed.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement a method named pnv_get_proc_freq(unsigned int cpu) which
returns the current clock rate on the 'cpu' in Hz to be reported in
/proc/cpuinfo. This method uses the value reported by cpufreq when
such a value is sane. Otherwise it falls back to old way of reporting
the clockrate, i.e. ppc_proc_freq.
Set the ppc_md.get_proc_freq() hook to pnv_get_proc_freq() on the
PowerNV platform.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the code in setup-common.c for powerpc assumes that all
clock rates are same in a smp system. This value is cached in the
variable named ppc_proc_freq and is the value that is reported in
/proc/cpuinfo.
However on the PowerNV platform, the clock rate is same only across
the threads of the same core. Hence the value that is reported in
/proc/cpuinfo is incorrect on PowerNV platforms. We need a better way
to query and report the correct value of the processor clock in
/proc/cpuinfo.
The patch achieves this by creating a machdep_call named
get_proc_freq() which is expected to returns the frequency in Hz. The
code in show_cpuinfo() can invoke this method to display the correct
clock rate on platforms that have implemented this method. On the
other powerpc platforms it can use the value cached in ppc_proc_freq.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Firmware update on PowerNV platform takes several minutes. During
this time one CPU is stuck in FW and the kernel complains about "soft
lockups".
This patch returns all secondary CPUs to firmware before starting
firmware update process.
[ Reworked a bit and cleaned up -- BenH ]
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates the implementation of pci_process_bridge_OF_ranges to use
the of_pci_range_parser helpers.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support to legacy serial for
UARTS with shifted registers.
The MVME5100 Single Board Computer is a PowerPC platform
that has 16550 style UARTS with register addresses that are
16 bytes apart (shifted by 4).
Commit 309257484c
"powerpc: Cleanup udbg_16550 and add support for LPC PIO-only UARTs"
added support to udbg_16550 for shifted registers by adding a "stride"
parameter to the initialisation operations for Programmed IO and
Memory Mapped IO.
As a consequence it is now possible to use the services of legacy serial
to provide early serial console messages for the MVME5100.
An added benefit of this is that the serial console will always be
"ttyS0" irrespective of whether the computer is fitted with extra
PCI 8250 interface boards or not.
I have tested this patch using the four PowerPC platforms available to me:
MVME5100 - shifted registers,
SAM440EP - unshifted registers,
MPC8349 - unshifted registers,
MVME4100 - unshifted registers.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code is only slightly modified : entry points now use the
FIXUP_ENDIAN trampoline to switch endian order. The 32bit wrapper
is kept for big endian kernels and 64bit is enforced for little
endian kernels with a PPC64_BOOT_WRAPPER config option.
The linker script is generated using the kernel preprocessor flags
to make use of the CONFIG_* definitions and the wrapper script is
modified to take into account the new elf64ppc format.
Finally, the zImage file is compiled as a position independent
executable (-pie) which makes it loadable at any address by the
firmware.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When entering the boot wrapper in little endian, we will need to fix
the endian order using a fixup trampoline like in the kernel. This
patch overrides the _zimage_start entry point for this purpose.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support a 64bit wrapper entry point. As in 32bit, the
entry point does its own relocation and can be loaded at any address
by the firmware.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch defines a 'prom' routine similar to 'enter_prom' in the
kernel.
The difference is in the MSR which is built before entering prom. Big
endian order is enforced as in the kernel but 32bit mode is not. It
prepares ground for the next patches which will introduce Little endian
order.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It could certainly be improved using Elf macros and byteswapping
routines, but the initial version of the code is organised to be a
single file program with limited dependencies. yaboot is the same.
Please scream if you want a total rewrite.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These are not the most efficient versions of swab but the wrapper does
not do much byte swapping. On a big endian cpu, these routines are
a no-op.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/boot/oflib.c:211:9: warning: cast to pointer from integer of \
different size [-Wint-to-pointer-cast]
return (phandle) of_call_prom("finddevice", 1, 1, name);
This is a work around. The definite solution would be to define the
phandle typedef as a u32, as in the kernel, but this would break the
device tree ops API.
Let it be for the moment.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes 64bit compile warnings and updates the wrapper code
to converge the kernel code in prom_init.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is mostly useful to make to the boot wrapper code closer with
the kernel code in prom_init.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Values will need to be byte-swapped when calling prom (big endian) from
a little endian boot wrapper.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates the wrapper code to converge with the kernel code in
prom_init.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes warnings when the wrapper is compiled in 64bit and
updates the boot wrapper code related to prom to converge with the
kernel code in prom_init. This should make the review of changes easier.
The kernel has a different number of possible arguments (10) when
entering prom. There does not seem to be any good reason to have
12 in the wrapper, so the patch changes this value to args[10] in
the prom_args struct.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the boot wrapper is compiled in 64bit, there is no need to
use __div64_32.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Function early_init_dt_scan_fw_dump() is called to scan the device
tree for fdump properties under node "rtas". Any one of them is
invalid, we can stop scanning the device tree early by returning
"1". It would save a bit time during boot.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the PE contains single PCI function, "pe->pbus" would be NULL.
It's not reliable to be used by pci_domain_nr(). We just grab the
PCI domain number from the PCI host controller (struct pci_controller)
instance.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In function pnv_pci_ioda2_setup_dma_pe(), the IOMMU table type is
set to (TCE_PCI_SWINV_CREATE | TCE_PCI_SWINV_FREE) unconditionally.
It was just set to TCE_PCI by pnv_pci_setup_iommu_table(). So the
primary IOMMU table type (TCE_PCI) is lost. The patch fixes it.
Also, pnv_pci_setup_iommu_table() already set "tbl->it_busno" to
zero and we needn't do it again. The patch removes the redundant
assignment.
The patch also fixes similar issues in pnv_pci_ioda_setup_dma_pe().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch intends to support fundamental reset on PLX downstream
ports. If the PCI device matches any one of the internal table,
which includes PLX vendor ID, bridge device ID, register offset
for fundamental reset and bit, fundamental reset will be done
accordingly. Otherwise, it will fail back to hot reset.
Additional flag (EEH_DEV_FRESET) is introduced to record the last
reset type on the PCI bridge.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When PCI_ERS_RESULT_CAN_RECOVER returned from device drivers, the
EEH core should enable I/O and DMA for the affected PE. However,
it was missed to have DMA enabled in eeh_handle_normal_event().
Besides, the frozen state of the affected PE should be cleared
after successful recovery, but we didn't.
The patch fixes both of the issues as above.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the kdump scenario, the first kerenl doesn't shutdown PCI devices
and the kdump kerenl clean PHB IODA table at the early probe time.
That means the kdump kerenl can't support PCI transactions piled
by the first kerenl. Otherwise, lots of EEH errors and frozen PEs
will be detected.
In order to avoid the EEH errors, the PHB is resetted to drop all
PCI transaction from the first kerenl.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The problem was initially reported by Wendy who tried pass through
IPR adapter, which was connected to PHB root port directly, to KVM
based guest. When doing that, pci_reset_bridge_secondary_bus() was
called by VFIO driver and linkDown was detected by the root port.
That caused all PEs to be frozen.
The patch fixes the issue by routing the reset for the secondary bus
of root port to underly firmware. For that, one more weak function
pci_reset_secondary_bus() is introduced so that the individual platforms
can override that and do specific reset for bridge's secondary bus.
Reported-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Basically, we have 3 types of resets to fulfil PE reset: fundamental,
hot and PHB reset. For the later 2 cases, we need PCI bus reset hold
and settlement delay as specified by PCI spec. PowerNV and pSeries
platforms are running on top of different firmware and some of the
delays have been covered by underly firmware (PowerNV).
The patch makes the delays unified to be done in backend, instead of
EEH core.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Resetting root port has more stuff to do than that for PCIe switch
ports and we should have resetting root port done in firmware instead
of the kernel itself. The problem was introduced by commit 5b2e198e
("powerpc/powernv: Rework EEH reset").
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In pseries_eeh_get_state(), EEH_STATE_UNAVAILABLE is always
overwritten by EEH_STATE_NOT_SUPPORT because of the missed
"break" there. The patch fixes the issue.
Reported-by: Joe Perches <joe@perches.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Once one specific PE has been marked as EEH_PE_ISOLATED, it's in
the middile of recovery or removed permenently. We needn't report
the frozen PE again. Otherwise, we will have endless reporting
same frozen PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
