If the controller receives a new SETUP during SETUP data stage,
and will generate SETUPENDISR interrupt, the driver should abort
the current SETUP command and process the new one.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the issue: device doesn't accept LGO_U1/U2:
1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2
by default;
2. enable/disable controller to initiate requests for transition into
U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable hardware remote wakeup from L1 automatically based on the FIFO
status, instead of manual way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The QMU checksum calculation is redundant, mostly used by debug,
so remove it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Originally, when dr_mode is USB_DR_MODE_HOST, it didn't power down device ip,
so host ip sleep will fail at ssusb_host_disable.
Power down device ip at ssusb_host_setup.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Power down feature of DWC2 module integrated in Samsung SoCs doesn't work
properly or needs some additional handling in PHY or SoC glue layer, so
disable it for now. Without disabling power down, DWC2 causes random memory
trashes and fails enumeration if there is no USB link to host on driver
probe.
Fixes: 03ea6d6e9e ("usb: dwc2: Enable power down")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Availability of TRB's is calculated using dwc3_calc_trbs_left(), which
determines total available TRB's based on the HWO bit set in a TRB.
In the present code, __dwc3_prepare_one_trb() is called with a TRB which
needs to be prepared for transfer. This __dwc3_prepare_one_trb() calls
dwc3_calc_trbs_left() to determine total available TRBs and set IOC bit
if the total available TRBs are zero. Since the present working TRB (which
is passed as an argument to __dwc3_prepare_one_trb() ) doesn't yet have
the HWO bit set before calling dwc3_calc_trbs_left(), there are chances
that dwc3_calc_trbs_left() wrongly calculates this present working TRB
as free(since the HWO bit is not yet set) and returns the total available
TRBs as greater than zero (including the present working TRB). This could
be a problem.
This patch corrects the above mentioned problem in __dwc3_prepare_one_trb()
by increementing the dep->trb_enqueue at the last (after preparing the TRB)
instead of increementing at the start and setting the IOC bit only if the
total available TRBs returned by dwc3_calc_trbs_left() is 1 . Since we are
increementing the dep->trb_enqueue at the last, the present working TRB is
also considered as available by dwc3_calc_trbs_left() and non zero value is
returned . So, according to the modified logic, when the total available
TRBs is equal to 1 that means the total available TRBs in the pool are 0.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The stream capable endpoints require stream id to be given
when issuing START TRANSFER. While issuing no-op trb the
stream id is not yet known, so don't issue no-op trb's on
stream capable endpoints.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For stream capable endpoints, stream id related information
needs to be updated into DEPCMD while issuing START TRANSFER.
This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget driver may take an unbounded amount of time to queue requests
after XferNotReady. This is important for isochronous endpoints which
need to be started for a specific (micro-)frame.
If we fail to start a transfer for isochronous endpoint, let's try
queueing to a future interval and see if that helps. We will stop trying
if we fail a start transfer for 5 intervals in the future.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Running out of requests on isochronous endpoints is part of normal
operation. We don't really need to know about it every time it
happens.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
They are much more useful in hexadecimal than in decimal. Moreover,
generic commands are already logged in hex.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sometimes, errors happen when kicking transfers from
__dwc3_gadget_start_isoc(). In those cases, we need to pass along the
error so gadget driver can make informed decisions.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have a list of cancelled requests, we can skip over TRBs
when END_TRANSFER command completes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Whenever we have a request in flight, we can move it to the cancelled
list and later simply iterate over that list and skip over any TRBs we
find.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Extract the logic for skipping over TRBs to its own function. This
makes the code slightly more readable and makes it easier to move this
call to its final resting place as a following patch.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we track how many TRBs a request uses, it's easier to skip
over them in case of a call to usb_ep_dequeue(). Let's do so and
simplify the code a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Both flags are used for the same purpose in dwc3: appending an extra
TRB at the end to deal with controller requirements. By combining both
flags into one, we make it clear that the situation is the same and
that they should be treated equally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DWC_usb31 version 1.70a-ea06 and prior, for highspeed and fullspeed
isochronous IN, BIT[15:14] of the 16-bit microframe number reported by
the XferNotReady event are invalid. The driver uses this number to
schedule the isochronous transfer and passes it to the START TRANSFER
command. Because this number is invalid, the command may fail. If
BIT[15:14] matches the internal 16-bit microframe, the START TRANSFER
command will pass and the transfer will start at the scheduled time, if
it is off by 1, the command will still pass, but the transfer will start
2 seconds in the future. For all other conditions, the START TRANSFER
command will fail with bus-expiry.
In order to workaround this issue, we can test for the correct
combination of BIT[15:14] by sending START TRANSFER commands with
different values of BIT[15:14]: 'b00, 'b01, 'b10, and 'b11. Each
combination is 2^14 uframe apart (or 2 seconds). 4 seconds into the
future will result in a bus-expiry status. As the result, within the 4
possible combinations for BIT[15:14], there will be 2 successful and 2
failure START COMMAND status. One of the 2 successful command status
will result in a 2-second delay start. The smaller BIT[15:14] value is
the correct combination.
Since there are only 4 outcomes and the results are ordered, we can
simply test 2 START TRANSFER commands with BIT[15:14] combinations 'b00
and 'b01 to deduce the smaller successful combination.
Let test0 = test status for combination 'b00 and test1 = test status for
'b01 of BIT[15:14]. The correct combination is as follow:
if test0 fails and test1 passes, BIT[15:14] is 'b01
if test0 fails and test1 fails, BIT[15:14] is 'b10
if test0 passes and test1 fails, BIT[15:14] is 'b11
if test0 passes and test1 passes, BIT[15:14] is 'b00
Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 peripheral v1.70a-ea06 and prior needs a SW workaround for
isoc START TRANSFER command failure. However, some affected versions may
have RTL patches to fix this without a SW workaround. Add this quirk to
disable the SW workaround when it is not needed.
Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a new field to dwc3 structure to track VERSIONTYPE. The VERSIONTYPE
is represented in ASCII in the 32-bit VERSIONTYPE register. In
DWC_usb31, sub releases for each version are tracked with VERSIONTYPE
such as "ea01" and "ea02".
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some protocols implemented in userspace with FunctionFS might require large
buffers, e.g. 64kB or more. Currently the said memory is allocated with
kmalloc, which might fail should system memory be highly fragmented.
On the other hand, some UDC hardware allows scatter-gather operation and
this patch takes advantage of this capability: if the requested buffer
is larger than PAGE_SIZE and the UDC allows scatter-gather operation, then
the buffer is allocated with vmalloc and a scatterlist describing it is
created and passed to usb request.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Nothing to remap, only check length.
Define a minimal structure for CCID descriptor only used to check length.
As this descriptor shares the same value as HID descriptors, keep track and
compare current interface's class to expected HID and CCID standard values.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistake in comment
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The vb2_ops structure can be const as it is only stored in the ops
field of a vb2_queue structure and this field is const.
Done with the help of Coccinelle.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG register
to accept LPM token during ISOC transfers when TxFIFO is
not empty.
- Added two definitions.
#define GLPMCFG_LPM_ACCEPT_CTRL_CONTROL BIT(21)
#define GLPMCFG_LPM_ACCEPT_CTRL_ISOC BIT(22)
This patch uses GLPMCFG_LPM_ACCEPT_CTRL_ISOC.
GLPMCFG_LPM_ACCEPT_CTRL_CONTROL is defined for further use.
- Added setting GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG
register in dwc2_gadget_init_lpm function.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to the databook DCTL_RMTWKUPSIG bit
is defined in DCTL register not in DCFG.
Updated setting DCTL_RMTWKUPSIG bit to DCTL
register.
Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG mode. If
the controller supports DRD but the dr_mode is not specified or set to
OTG, then set the mode to peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a safety connection way for "forced_b_device" with
"workaround_for_vbus" like below:
< Example for R-Car E3 Ebisu >
# modprobe <any usb gadget driver>
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
(connect a usb cable to host side.)
# echo 2 > /sys/kernel/debug/ee020000.usb/b_device
Previous code should have connected a usb cable before the "b_device"
is set to 1 on the Ebisu board. However, if xHCI driver on the board
is probed, it causes some troubles:
- Conflicts USB VBUS/signals between the board and another host.
- "Cannot enable. Maybe the USB cable is bad?" might happen on
both the board and another host with a usb hub.
- Cannot enumerate a usb gadget correctly because an interruption
of VBUS change happens unexpectedly.
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow extcon device, found by name, to provide DR status for USB.
This is needed, for example, in case of Intel Merrifield platform,
where the Intel Basin Cove PMIC provides an extcon device to communicate
the detected role.
Note, that the "linux,extcon-name" property name is only for kernel
internal use by X86/ACPI platform code and as such is not documented
in the device tree bindings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Switch to device property for 'extcon' handling.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's not very useful to repeat a bunch of probe deferral errors. And
it's also not very useful to log "failed" without telling the error
code.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The usb_gadget_ops structure can be const as it is only stored in
the ops field of a usb_gadget structure and this field is const.
Done with the help of Coccinelle.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support the option to disable USB2 LPM. Set xhci "usb2-lpm-disable"
property via "snps,usb2-lpm-disable" property.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add an option to disable USB2 LPM from host. There maybe cases where the
user does not want to enable USB2 LPM (e.g. USB2 LPM is broken).
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GUSB2PHYCFG.ENBLSLPM enables the controller to assert low power signals
to the PHY. Unless disabled via device property, explicitly set
GUSB2PHYCFG.ENBLSLPM as it may not be set by default.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Current implementation only prints/sets the link state for peripheral
mode only. Check and prevent printing bogus link state if the current
mode of operation is not peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Highspeed device and below has different state names than superspeed and
higher. Add proper checks and printouts of link states for highspeed and
below.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To dump internal LSP and endpoint state debug registers, we must write
to GDBGLSPMUX register. This patch correctly dump LSP and endpoint
states from the debug registers.
If the controller is in device mode, all LSP and endpoint state
registers will be dumped via the debugfs attribute "lsp_dump". In host
mode, the user has to write the LSP number to "lsp_dump" to dump a
specific LSP selection.
Fixes: 80b776340c ("usb: dwc3: Dump LSP and BMU debug info")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
TxFIFO and RxFIFO from GDBGFIFOSPACE are fifo depths in MDWIDTH. Convert
them into bytes for easier read.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Tx/RxFIFO types in the GDBGFIFOSPACE.FIFO_QUEUE_SELECT are not
queue. Properly rename them.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
- 0 is a valid physical address on some arm boards, we can't use
0 as the error value
- don't try to cache flush the error return value (no matter what it is)
-----BEGIN PGP SIGNATURE-----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=mdIx
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.20-3' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Two dma-direct / swiotlb regressions fixes:
- zero is a valid physical address on some arm boards, we can't use
it as the error value
- don't try to cache flush the error return value (no matter what it
is)"
* tag 'dma-mapping-4.20-3' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: Skip cache maintenance on map error
dma-direct: Make DIRECT_MAPPING_ERROR viable for SWIOTLB
Highlights include:
Bugfixes:
- Fix a NFSv4 state manager deadlock when returning a delegation
- NFSv4.2 copy do not allocate memory under the lock
- flexfiles: Use the correct stateid for IO in the tightly coupled case
-----BEGIN PGP SIGNATURE-----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=hqbe
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.20-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a NFSv4 state manager deadlock when returning a delegation
- NFSv4.2 copy do not allocate memory under the lock
- flexfiles: Use the correct stateid for IO in the tightly coupled case
* tag 'nfs-for-4.20-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
flexfiles: use per-mirror specified stateid for IO
NFSv4.2 copy do not allocate memory under the lock
NFSv4: Fix a NFSv4 state manager deadlock
I'm taking over the maintainance of Sparse so add myself as
maintainer and move Christopher's info to CREDITS.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We found some bugs in the DAX conversion to XArray (and one bug which
predated the XArray conversion). There were a couple of bugs in some of
the higher-level functions, which aren't actually being called in today's
kernel, but surfaced as a result of converting existing radix tree &
IDR users over to the XArray. Some of the other changes to how the
higher-level APIs work were also motivated by converting various users;
again, they're not in use in today's kernel, so changing them has a low
probability of introducing a bug.
Dan can still trigger a bug in the DAX code with hot-offline/online,
and we're working on tracking that down.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEejHryeLBw/spnjHrDpNsjXcpgj4FAlv542AUHHdpbGx5QGlu
ZnJhZGVhZC5vcmcACgkQDpNsjXcpgj5BoAf/QZzbBcYuYMLMDYofvHKGlmk2yx/a
ObUlxlQtXGHvPp3oC3rdwAvcN/KAMDpU0u+PXab2MnrNw5okhpS6ZwGODlkarNA4
XbVQNGbtEbACr1V3CWc0NzLbYm6JtGpMum0Wx9MVR/VdTnGArBLBYQMYa/c1YhKA
vEBPf+w0j0QoCTAgPiIvq0aksuBQERUvjhlUvoaMY7F4sAhnaW558lvaEcc1xGxq
70+3cRPT6Uh12tEvi0LKP1NNEXebvQSftMvFEUPF2xo5z2v//KEobzv/anbojxQ8
BtxouIGSr4tME9g3xSpd9rTbUcW3bwDAhuWZvpP/ViRwW2UkEQonpApdaw==
=0Ert
-----END PGP SIGNATURE-----
Merge tag 'xarray-4.20-rc4' of git://git.infradead.org/users/willy/linux-dax
Pull XArray updates from Matthew Wilcox:
"We found some bugs in the DAX conversion to XArray (and one bug which
predated the XArray conversion). There were a couple of bugs in some
of the higher-level functions, which aren't actually being called in
today's kernel, but surfaced as a result of converting existing radix
tree & IDR users over to the XArray.
Some of the other changes to how the higher-level APIs work were also
motivated by converting various users; again, they're not in use in
today's kernel, so changing them has a low probability of introducing
a bug.
Dan can still trigger a bug in the DAX code with hot-offline/online,
and we're working on tracking that down"
* tag 'xarray-4.20-rc4' of git://git.infradead.org/users/willy/linux-dax:
XArray tests: Add missing locking
dax: Avoid losing wakeup in dax_lock_mapping_entry
dax: Fix huge page faults
dax: Fix dax_unlock_mapping_entry for PMD pages
dax: Reinstate RCU protection of inode
dax: Make sure the unlocking entry isn't locked
dax: Remove optimisation from dax_lock_mapping_entry
XArray tests: Correct some 64-bit assumptions
XArray: Correct xa_store_range
XArray: Fix Documentation
XArray: Handle NULL pointers differently for allocation
XArray: Unify xa_store and __xa_store
XArray: Add xa_store_bh() and xa_store_irq()
XArray: Turn xa_erase into an exported function
XArray: Unify xa_cmpxchg and __xa_cmpxchg
XArray: Regularise xa_reserve
nilfs2: Use xa_erase_irq
XArray: Export __xa_foo to non-GPL modules
XArray: Fix xa_for_each with a single element at 0
Pull HID fixes from Jiri Kosina:
- revert of the high-resolution scrolling feature, as it breaks certain
hardware due to incompatibilities between Logitech and Microsoft
worlds. Peter Hutterer is working on a fixed implementation. Until
that is finished, revert by Benjamin Tissoires.
- revert of incorrect strncpy->strlcpy conversion in uhid, from David
Herrmann
- fix for buggy sendfile() implementation on uhid device node, from
Eric Biggers
- a few assorted device-ID specific quirks
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
Revert "Input: Add the `REL_WHEEL_HI_RES` event code"
Revert "HID: input: Create a utility class for counting scroll events"
Revert "HID: logitech: Add function to enable HID++ 1.0 "scrolling acceleration""
Revert "HID: logitech: Enable high-resolution scrolling on Logitech mice"
Revert "HID: logitech: Use LDJ_DEVICE macro for existing Logitech mice"
Revert "HID: logitech: fix a used uninitialized GCC warning"
Revert "HID: input: simplify/fix high-res scroll event handling"
HID: Add quirk for Primax PIXART OEM mice
HID: i2c-hid: Disable runtime PM for LG touchscreen
HID: multitouch: Add pointstick support for Cirque Touchpad
HID: steam: remove input device when a hid client is running.
Revert "HID: uhid: use strlcpy() instead of strncpy()"
HID: uhid: forbid UHID_CREATE under KERNEL_DS or elevated privileges
HID: input: Ignore battery reported by Symbol DS4308
HID: Add quirk for Microsoft PIXART OEM mouse
