On platforms that have CONFIG_HZ set to 100, the power ramp time effectively
ends up being 10ms. However, on those that have a higher CONFIG_HZ, the time
ends up *actually* being 5ms, which doesn't allow enough time for the hardware
to be fully powered up before attempting to address it via i2c.
Change the constant to 10ms, which is long enough for the hardware to power
up, and won't really be anymore time than it was previously on platforms
with CONFIG_HZ being 100.
Credit goes to Mauro Carvalho Chehab and Gerd Hoffmann who previously
investigated this issue.
Tested with the Hauppauge USBLive 2, with which the problem was readily
reproducible after setting CONFIG_HZ to 1000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch addresses the regression introduced in the cx231xx
driver which stopped the Hauppauge USBLive2 from working.
Confirmed working by both myself and the user who reported the issue
on the KernelLabs blog (Robert DeLuca).
At some point during refactoring of the cx231xx driver, the USBLive 2 device
became broken. This patch results in the device working again.
Thanks to Robert DeLuca for sponsoring this work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Robert DeLuca <robertdeluca@me.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The search for matching extension units fails to take account of the
current chain. In the case where you have two distinct video chains,
both containing an XU with the same GUID but different unit ids, you
will be unable to perform a mapping on the second chain because entity
on the first chain will always be found first
Fix this by only searching the current chain when performing a control
mapping. This is analogous to the search used by uvc_find_control(),
and is the correct behaviour.
Signed-off-by: Stephan Lachowsky <stephan.lachowsky@maxim-ic.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the DRX-K logic that selects between DVB-C annex A and C
Fix a typo where DVB-C annex type is set via setEnvParameters, but
the driver, uses, instead, setParamParameters[2].
While here, cleans up the code, fixing a bad identation at the fallback
code for other types of firmware, and put the multiple-line comments
into the Linux CodingStyle.
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After return, we don't need any other statement to change the
function flux ;)
Reported-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error propagation changeset c23bf4402 broke the DVB-T
code.
The legacy way for propagate errors was:
do {
status = foo_func()
if (status < 0)
break;
} while (0);
return status;
However, on a few places, it was doing:
do {
switch(foo) {
case bar:
status = foo_func()
if (status < 0)
break;
break;
}
switch(foo2) {
case bar:
status = foo_func()
if (status < 0)
break;
break;
}
...
} while (0);
return (status)
The inner error break were not working, as it were breaking only
the switch, instead of the do. The solution used were to do a
s/break/goto error/ at the inner breaks, but preserving the last
break. Onfortunately, on a few switches, the replacement were
applied also to the final break for the case statements.
Fix the broken logic, by reverting them to break, where pertinent,
in order to fix DVB-T support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both ngene and ddbrige calls dvb_attach once for drxk_attach.
The logic used there, and by tda18271c2dd driver is different
from similar logic on other frontends.
The right fix is to change them to use the same logic, but,
while we don't do that, we need to patch em28xx-dvb in order
to do cope with ngene/ddbridge magic.
While here, document why drxk_t_release should do nothing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit a3e4adf274f86b2363fedaa964297cb38526cef0.
As pointed by Andread Oberritter <obi@linuxtv.org>:
That's wrong, because the array size is DTV_MAX_COMMAND + 1.
Using the ARRAY_SIZE macro instead might reduce the confusion.
Also, changeset 3995223038 already fixed this issue.
Reported-by: Andread Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch adds a new control that makes it possible to set the
luma notch filter type to finetune picture quality.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements support for a sharpness control, using the luma
peaking filter feature of cx2388x.
[mchehab@redhat.com: use cx_andor instead of cx_write]
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add driver for TV Mixer on Samsung platforms from S5P family.
Mixer is responsible for merging images from three layers and
passing result to the output.
Drivers are using:
- v4l2 framework
- videobuf2
- runtime PM
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add drivers for Standard Definition output (SDO) on Samsung platforms
from S5P family. The driver provides control over streaming analog TV
via Composite connector.
Driver is using:
- v4l2 framework
- runtime PM
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callback is used to acquire current analog TV standard from a subdev.
It is used to avoid keeping current standard in top-level driver.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callback is used to acquire current digital video preset from a subdev.
It is used to avoid keeping dv preset in top-level driver.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callback is used to acquire TV norms supported by a subdev.
It is used to avoid having standards in top-level driver.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx88 driver would force core->input to always be zero when doing the
the request_acquire(). While it wasn't actually changing the input register
in the hardware, the driver makes decision based on the current input. In
particular, it decides whether to do things like enabling the comb filter
when on a composite input but disabling it on s-video. So for example, on
the HVR-1300, using the s-video input with the MPEG encoder would end up with
the video decoder core configured as though the input type were composite.
In short, the driver state did not match the hardware state.
This patch does two things:
1. It forces the input to zero only if actually switching to DVB mode. This
prevents the input from changing when the blackbird driver opens the device.
2. Keep track of what the input was set to when switching to DVB, and reset
it back when done. This eliminates a condition where for example the user
had the analog side of the board set to capture on the s-video input, then
he used DVB for a bit, then the analog input would unexpectedly be set to
the tuner input.
This work was sponsored by Anevia S.A.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multi Format Codec 5.1 is a hardware video coding acceleration
module found in the S5PV210 and Exynos4 Samsung SoCs. It is
capable of handling a range of video codecs and this driver
provides a V4L2 interface for video decoding and encoding.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is admittedly a bit of a hack, but if we change our timeout value
to something longer and fudge our synthesized trailing space sample
based on the initial pulse sample, rc-core decode continues to work just
fine with both rc-6 and rc-5, and now lirc userspace decode shows proper
repeats for both of those protocols as well. Also tested NEC
successfully with both decode options.
We do still need a reset timer callback using the hardware's timeout
value to make sure we actually process samples correctly, regardless of
our somewhat hacky timeout and synthesized trailer above.
This also adds a missing del_timer_sync call to the module unload path.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trying to cap duration before multiplying it was obviously wrong.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We already add a trailing space, this wasn't doing anything useful, and
actually confused lirc userspace a bit. Rip it out.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is useless. There is only one physical I2C-adapter.
2nd adapter was added originally due to some plans for allowing only one
demod to access bus at time. But I never implemented proper locking...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove old code which is not used anymore since IR code is read
directly from memory nowadays.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reported-by: Jacek M. Holeczek <jacek.m.holeczek@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That's this tuner:
The credit card sized remote more or less works if I set remote=4,
so I added the hash to get it autodetected. (`more or less' there
meaning sometimes buttons are `stuck on repeat', i.e. ir-keytable -t
keeps repeating the same scancode until i press another button.)
Signed-off-by: Juergen Lock <nox@jelal.kn-bremen.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In drivers/media/dvb/frontends/drxd_hard.c::load_firmware() I see 3
small issues:
1) When the 'fw' variable goes out of scope we'll leak the memory
allocated to it by request_firmware() by neglecting to call
release_firmware().
2) After a successful request_firmware() we allocate fw->size bytes
of memory using kzalloc() only to immediately overwrite all that
memory with memcpy(), so asking for zeroed memory seems like wasted
effort - just use kmalloc().
3) In one of the error messages "no memory" lacks a space and is
written as "nomemory".
This patch fixes all 3 issues.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Microsoft's Windows Media Center specification and requirements doc from
2011.03.18 now refers to the former Power Toggle button as the Sleep
Toggle, and recommends using a new moon sleep icon for it. Its the same
key, but its apparently always been meant to put the system to sleep,
not power it off. Adjust accordingly. While we're here, lets also remove
the duplicate KEY_PLAYPAUSE entry.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clear the cx231xx_devused variable and free dev in the error handling code,
as done in the error handling code nearby.
The semantic match that finds this problem is as follows:
// <smpl>
@r@
identifier x;
@@
kfree(x)
@@
identifier r.x;
expression E1!=0,E2,E3,E4;
statement S;
@@
(
if (<+...x...+>) S
|
if (...) { ... when != kfree(x)
when != if (...) { ... kfree(x); ... }
when != x = E3
* return E1;
}
... when != x = E2
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Free the recently allocated qcam in each case.
The semantic match that finds this problem is as follows:
// <smpl>
@r@
identifier x;
@@
kfree(x)
@@
identifier r.x;
expression E1!=0,E2,E3,E4;
statement S;
@@
(
if (<+...x...+>) S
|
if (...) { ... when != kfree(x)
when != if (...) { ... kfree(x); ... }
when != x = E3
* return E1;
}
... when != x = E2
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were several coding style errors as reported by checkpatch.pl. This
patch should fix those errors with the single exception of the open square
bracket issue on line 45.
[mchehab@redhat.com: Fix a merge conflict]
Signed-off-by: Adam M. Dutko <dutko.adam@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the tvp->cmd == DTV_MAX_COMMAND then we read past the end of the
array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch, based on code by Mirek Slugen, implements support for the
Leadtek WinFast PxDVR3200 H card with XC4000 tuner (107d:6f39).
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure that the 'static' keywork is at the beginning of declaration
for drivers/media/video/omap/omap_vout.c
This gets rid of warnings like
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delete a couple of leftover fields whose time has passed.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Marvell camera core can support all three videobuf2 buffer modes, which
is slick, but it also requires that all three modes be built and present,
even though only one is likely to be used. This patch allows the supported
modes to be selected at configuration time, reducing the footprint of the
driver. Prior to this patch, the MMP camera driver looked like this:
mmp_camera 19092 0
videobuf2_core 15542 1 mmp_camera
videobuf2_dma_sg 3173 1 mmp_camera
videobuf2_dma_contig 2188 1 mmp_camera
videobuf2_vmalloc 1718 1 mmp_camera
videobuf2_memops 2100 3 videobuf2_dma_sg,videobuf2_dma_contig,videobuf2_vmalloc
Afterward, instead, with scatter/gather only configured:
mmp_camera 16021 0
videobuf2_core 15542 1 mmp_camera
videobuf2_dma_sg 3173 1 mmp_camera
videobuf2_memops 2100 1 videobuf2_dma_sg
The total goes from 43,813 bytes to 36,836.
The emphasis has been on simplicity and minimal #ifdef use rather than on
squeezing out every possible byte of code. For configuration, the driver
simply looks at which videobuf2 modes have been configured in and supports
them all; it's simplistic but should be good enough.
The cafe driver is set to support vmalloc and dma-contig; mmp supports only
dma-sg, since that's the only mode that really makes sense to use.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If registration does not work, we don't want to leave the sensor powered on.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Somewhere along the way the code stopped actually paying any attention to
them, and I doubt anybody has ever made use of them.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code shows signs of having been mucked with over the last five years
or so; things were kind of mixed up. This patch reorders functions into a
more rational organization which, with luck, will facilitate making the
buffer modes selectable at configuration time. Code movement only: no
functional changes here.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This structure got passed over in the videobuf2 conversion; it has no
reason to exist now.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The third parameter of module_param is supposed to represent sysfs
file permissions. A value of "1" leads to the following:
$ ls -l /sys/module/radio_tea5764/parameters/
total 0
I am changing it to "0" to align with the other module parameters in
this driver.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Fabio Belavenuto <belavenuto@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on the work of John Newbigin, Davor Emard and others who contributed
on the mailing lists.
The previous 'support' for this card was a partial merge of John's changes
that, as far as I can tell, never actually got the thing working (no DVB-T,
analog tuner not initialised).
Initialise the analog tuner properly and hook up the DVB tuner and demodulator.
DVB-T and analog now work (though I can't tune every DVB channel, but I think
there's an issue with the aerial and signal boosters here that is causing
me problems).
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
