Hayes Wang says:
====================
r8152: patches about firmware
The patches fix the issues when the firmware exists.
For the multiple OS, the firmware may be loaded by the
driver of the other OS. And the Linux driver has influences
on it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware would be clear when the power cut is enabled for
RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed by the firmware would occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver, similar to tg3, has a check that will
cause full sized 802.1ad frames to be dropped. The
frame will be larger then the standard mtu due to the
presense of vlan header that has not been stripped.
The driver should not drop this frame and should process
it just like it does for 802.1q.
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of RTL8152_UNPLUG should only be set when the device is
unplugged, not each time the rtl8152_disconnect() is called.
Otherwise, the device wouldn't be stopped normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra says:
====================
netxen: Bug fixes.
This series fixes some TX specific issues.
* Move spin_lock(tx_clean_lock) in down path to fix
atomic sleep bug (Reported by Mike Galbraith).
* Fix hang in interface down while running traffic.
Please consider applying this to 'net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Due to this interface down path gets
stuck forever waiting for NAPI to complete.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o __netxen_nic_down() function might sleep while holding spinlock_t(tx_clean_lock).
Acquire this lock for only releasing TX buffers instead of taking it
for whole down path.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet noticed that all no-nonexthop or no-gateway routes which
are already marked DST_HOST (e.g. input routes routes) will always be
invalidated during sk_dst_check. Thus per-socket dst caching absolutely
had no effect and early demuxing had no effect.
Thus this patch removes rt6i_genid: fn_sernum already gets modified during
add operations, so we only must ensure we mutate fn_sernum during ipv6
address remove operations. This is a fairly cost extensive operations,
but address removal should not happen that often. Also our mtu update
functions do the same and we heard no complains so far. xfrm policy
changes also cause a call into fib6_flush_trees. Also plug a hole in
rt6_info (no cacheline changes).
I verified via tracing that this change has effect.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Long Li <longli@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the CONFIG_HAVE_CLK is selected for the system, the stmmac_pci_probe
will fail with dmesg:
[ 2.167225] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 2.178267] stmmaceth 0000:00:14.6: enabling bus mastering
[ 2.178436] stmmaceth 0000:00:14.6: irq 24 for MSI/MSI-X
[ 2.178703] stmmaceth 0000:00:14.6: stmmac_dvr_probe: warning: cannot
get CSR clock
[ 2.186503] stmmac_pci_probe: main driver probe failed
[ 2.194003] stmmaceth 0000:00:14.6: disabling bus mastering
[ 2.196473] stmmaceth: probe of 0000:00:14.6 failed with error -2
This patch fix the issue by breaking the dependency to devm_clk_get()
as the CSR clock can be obtained at priv->plat->clk_csr from pci driver.
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Negated expressions and sub-expressions need to have their flags checked for
TCF_EM_INVERT and their result negated accordingly.
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8a29111c7c ("net: gro: allow to build full sized skb")
I added a regression for linear skb that traditionally force GRO
to use the frag_list fallback.
Erez Shitrit found that at most two segments were aggregated and
the "if (skb_gro_len(p) != pinfo->gso_size)" test was failing.
This is because pinfo at this spot still points to the last skb in the
chain, instead of the first one, where we find the correct gso_size
information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Reported-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit f187bc6efb ("ipv4: No need to set generic neighbour pointer")
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
ipv6: Return an error when adding an already existing tunnel
The ipv6 tunnel locate functions should not return an existing
tunnel if create is true. Otherwise it is possible to add the
same tunnel multiple times without getting an error.
All our ipv6 tunnels have this bug from the very beginning.
Only the sit tunnel was fixed some years ago with:
commit 8db99e5717 ("sit: Fail to create tunnel, if it already exists").
This patchset fixes the remaining ipv6 tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6gre_tunnel_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vti6_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_tnl_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this alias, we don't need to load manually the module before adding an
ip6gretap interface with iproute2.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HCA is configured in SRIOV IB mode (that is, at least one of
the ports is IB) and the probe_vf module param isn't specified,
mlx4_init_one() failed because of the following condition:
if (ib_ports && (num_vfs_argc > 1 || probe_vfs_argc > 1)) {
.....
}
The root cause for that is a mistake in the initialization of num_vfs_argc
and probe_vfs_argc. When num_vfs / probe_vf aren't given, their argument
count counterpart should be 0, fix that.
Fixes: dd41cc3bb9 ('net/mlx4: Adapt num_vfs/probed_vf params for single port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
nf pull request for net
This series contains netfilter fixes for net, they are:
1) Fix lockdep splat in nft_hash when releasing sets from the
rcu_callback context. We don't the mutex there anymore.
2) Remove unnecessary spinlock_bh in the destroy path of the nf_tables
rbtree set type from rcu_callback context.
3) Fix another lockdep splat in rhashtable. None of the callers hold
a mutex when calling rhashtable_destroy.
4) Fix duplicated error reporting from nfnetlink when aborting and
replaying a batch.
5) Fix a Kconfig issue reported by kbuild robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off would be called when autoresuming, even though
the cable is plugged. This causes some applications do relative
actions when detecting the carrier off. Keep the status of the
carrier, and let it be modified when the linking change occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8ef29f8aae.
The driver core already calls pinctrl_get() and claims the default
state. There is no need to replicate this in the driver.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In macvtap device delete and open calls can race and
this causes a list curruption of the vlan queue_list.
The race intself is triggered by the idr accessors
that located the vlan device. The device is stored
into and removed from the idr under both an rtnl and
a mutex. However, when attempting to locate the device
in idr, only a mutex is taken. As a result, once cpu
perfoming a delete may take an rtnl and wait for the mutex,
while another cput doing an open() will take the idr
mutex first to fetch the device pointer and later take
an rtnl to add a queue for the device which may have
just gotten deleted.
With this patch, we now hold the rtnl for the duration
of the macvtap_open() call thus making sure that
open will not race with delete.
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra says:
====================
qlcnic: Bug fixes.
This patch series contains following bug fixes:
* Fixes related to ethtool statistics.
* Fix for flash read related API.
Please apply this series to 'net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o When TX queues are not allocated, driver does not fill TX queues stats in the buffer.
However, it is also not advancing data pointer by TX queue stats length, which would
misplace all successive stats data in the buffer and will result in mismatch between
stats strings and it's values.
o Fix this by advancing data pointer by TX queue stats length when
queues are not allocated.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o TX queues stats must be read when queues are allocated regardless
of interface is up or not.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver is doing memset with zero for total number of stats bytes when
it has already filled some data in the stats buffer, which can overwrite
memory area beyond the length of stats buffer.
o Fix this by initializing stats buffer with zero before filling any data in it.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In qlcnic_83xx_setup_idc_parameters() routine use qlcnic_83xx_flash_read32() API
which takes flash lock internally instead of the lockless version
qlcnic_83xx_lockless_flash_read32().
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we try to add an already existing tunnel, we don't return
an error. Instead we continue and call ip_tunnel_update().
This means that we can change existing tunnels by adding
the same tunnel multiple times. It is even possible to change
the tunnel endpoints of the fallback device.
We fix this by returning an error if we try to add an existing
tunnel.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Here is a quick pull request primarily meant to address the deconfig
fallout from changing SCSI_NETLINK from being used via 'select' to
being used via 'depends'.
I applied a set of 5 patches written by Michal Marek, and then I
carefully audited all of the remaining config files, basically:
1) I scanned every arch config file, and if it mentioned CONFIG_INET
or CONFIG_UNIX, I made sure it had CONFIG_NET=y
2) After that, I scanned every arch config file, and if it did not
have CONFIG_NET=y I made sure it did not reference any networking
config options.
Finally, we have some late breaking wireless fixes in here from John
Linville and co"
[ And there's a sparc bpf fix snuck in too ]
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sparc: bpf_jit: fix loads from negative offsets
parisc: Update defconfigs which were missing CONFIG_NET.
powerpc: Update defconfigs which were missing CONFIG_NET.
s390: Update defconfigs which were missing CONFIG_NET.
mips: Update some more defconfigs which were missing CONFIG_NET.
sparc: Set CONFIG_NET=y in defconfigs
sh: Set CONFIG_NET=y in defconfigs
powerpc: Set CONFIG_NET=y in defconfigs
parisc: Set CONFIG_NET=y in defconfigs
mips: Set CONFIG_NET=y in defconfigs
brcmfmac: Fix off by one bug in brcmf_count_20mhz_channels()
ath9k: Fix NULL pointer dereference on early irq
net: rfkill: gpio: Fix clock status
NFC: st21nfca: Fix potential depmod dependency cycle
NFC: st21nfcb: Fix depmod dependency cycle
NFC: microread: Potential overflows in microread_target_discovered()
- fix BPF_LD|ABS|IND from negative offsets:
make sure to sign extend lower 32 bits in 64-bit register
before calling C helpers from JITed code, otherwise 'int k'
argument of bpf_internal_load_pointer_neg_helper() function
will be added as large unsigned integer, causing packet size
check to trigger and abort the program.
It's worth noting that JITed code for 'A = A op K' will affect
upper 32 bits differently depending whether K is simm13 or not.
Since small constants are sign extended, whereas large constants
are stored in temp register and zero extended.
That is ok and we don't have to pay a penalty of sign extension
for every sethi, since all classic BPF instructions have 32-bit
semantics and we only need to set correct upper bits when
transitioning from JITed code into C.
- though instructions 'A &= 0' and 'A *= 0' are odd, JIT compiler
should not optimize them out
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-09-23
Please consider pulling this one last batch of fixes intended for the 3.17 stream!
For the NFC bits, Samuel says:
"Hopefully not too late for a handful of NFC fixes:
- 2 potential build failures for ST21NFCA and ST21NFCB, triggered by a
depmod dependenyc cycle.
- One potential buffer overflow in the microread driver."
On top of that...
Emil Goode provides a fix for a brcmfmac off-by-one regression which
was introduced in the 3.17 cycle.
Loic Poulain fixes a polarity mismatch for a variable assignment
inside of rfkill-gpio.
Wojciech Dubowik prevents a NULL pointer dereference in ath9k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit df568d8e ("scsi: Use 'depends' with LIBFC instead of
'select'.") removed what happened to be the only instance of 'select
NET'. Defconfigs that were relying on the select now lack networking
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d6be6a5 ("scsi_netlink : Make SCSI_NETLINK dependent on NET
instead of selecting NET") removed what happened to be the only instance
of 'select NET'. Defconfigs that were relying on the select now lack
networking support.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-mips@linux-mips.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull one last block fix from Jens Axboe:
"We've had an issue with scsi-mq where probing takes forever. This was
bisected down to the percpu changes for blk_mq_queue_enter(), and the
fact we now suffer an RCU grace period when killing a queue. SCSI
creates and destroys tons of queues, so this let to 10s of seconds of
stalls at boot for some.
Tejun has a real fix for this, but it's too involved for 3.17. So
this is a temporary workaround to expedite the queue killing until we
can fold in the real fix for 3.18 when that merge window opens"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe
Enumeration
- Revert "PCI: Don't scan random busses in pci_scan_bridge()" (Bjorn Helgaas)
- Revert "PCI: Make sure bus number resources stay within their parents bounds" (Bjorn Helgaas)
PCI device hotplug
- Fix pciehp pcie_wait_cmd() timeout (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qP+Z
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a few fixes that should be in v3.17.
- Reverting "Don't scan random busses" covers up a CardBus regression
having to do with allocating CardBus bus numbers.
- Reverting "Make sure bus numbers stay within parents bounds" covers
up an ACPI _CRS bug that makes us reconfigure a bridge, causing a
broken device behind it to stop responding.
- The pciehp timeout change fixes some code we added in v3.17.
Without the fix, we can send a new hotplug command too early,
before the timeout has expired.
I hope for better fixes for the reverts, but those will have to come
after v3.17"
* tag 'pci-v3.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: pciehp: Fix pcie_wait_cmd() timeout
Revert "PCI: Make sure bus number resources stay within their parents bounds"
Revert "PCI: Don't scan random busses in pci_scan_bridge()"
Pull crypto fixes from Herbert Xu:
"This fixes three issues:
- if ccp is loaded on a machine without ccp, it will incorrectly
activate causing all requests to fail. Fixed by preventing ccp
from loading if hardware isn't available.
- not all IRQs were enabled for the qat driver, leading to potential
stalls when it is used
- disabled buggy AVX CTR implementation in aesni"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni - disable "by8" AVX CTR optimization
crypto: ccp - Check for CCP before registering crypto algs
crypto: qat - Enable all 32 IRQs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nEDO
-----END PGP SIGNATURE-----
Merge tag 'media/v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For some last time fixes:
- a regression detected on Kernel 3.16 related to VBI Teletext
application breakage on drivers using videobuf2 (see
https://bugzilla.kernel.org/show_bug.cgi?id=84401). The bug was
noticed on saa7134 (migrated to VB2 on 3.16), but also affects
em28xx (migrated on 3.9 to VB2);
- two additional sanity checks at videobuf2;
- two fixups to restore proper VBI support at the em28xx driver;
- two Kernel oops fixups (at cx24123 and cx2341x drivers);
- a bug at adv7604 where an if was doing just the opposite as it
would be expected;
- some documentation fixups to match the behavior defined at the
Kernel"
* tag 'media/v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] em28xx-v4l: get rid of field "users" in struct em28xx_v4l2"
[media] em28xx: fix VBI handling logic
[media] DocBook media: improve the poll() documentation
[media] DocBook media: fix the poll() 'no QBUF' documentation
[media] vb2: fix VBI/poll regression
[media] cx2341x: fix kernel oops
[media] cx24123: fix kernel oops due to missing parent pointer
[media] adv7604: fix inverted condition
[media] media/radio: fix radio-miropcm20.c build with io.h header file
[media] vb2: fix plane index sanity check in vb2_plane_cookie()
[media] DocBook media: update version number and V4L2 changes
[media] DocBook media: fix fieldname in struct v4l2_subdev_selection
[media] vb2: fix vb2 state check when start_streaming fails
[media] videobuf2-core.h: fix comment
[media] videobuf2-core: add comments before the WARN_ON
[media] videobuf2-dma-sg: fix for wrong GFP mask to sg_alloc_table_from_pages
particularly, but not only, fixing new "resync" code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=gMsu
-----END PGP SIGNATURE-----
Merge tag 'md/3.17-more-fixes' of git://git.neil.brown.name/md
Pull bugfixes for md/raid1 from Neil Brown:
"It is amazing how much easier it is to find bugs when you know one is
there. Two bug reports resulted in finding 7 bugs!
All are tagged for -stable. Those that can't cause (rare) data
corruption, cause lockups.
Particularly, but not only, fixing new "resync" code"
* tag 'md/3.17-more-fixes' of git://git.neil.brown.name/md:
md/raid1: fix_read_error should act on all non-faulty devices.
md/raid1: count resync requests in nr_pending.
md/raid1: update next_resync under resync_lock.
md/raid1: Don't use next_resync to determine how far resync has progressed
md/raid1: make sure resync waits for conflicting writes to complete.
md/raid1: clean up request counts properly in close_sync()
md/raid1: be more cautious where we read-balance during resync.
md/raid1: intialise start_next_window for READ case to avoid hang
blk-mq uses percpu_ref for its usage counter which tracks the number
of in-flight commands and used to synchronously drain the queue on
freeze. percpu_ref shutdown takes measureable wallclock time as it
involves a sched RCU grace period. This means that draining a blk-mq
takes measureable wallclock time. One would think that this shouldn't
matter as queue shutdown should be a rare event which takes place
asynchronously w.r.t. userland.
Unfortunately, SCSI probing involves synchronously setting up and then
tearing down a lot of request_queues back-to-back for non-existent
LUNs. This means that SCSI probing may take more than ten seconds
when scsi-mq is used.
This will be properly fixed by implementing a mechanism to keep
q->mq_usage_counter in atomic mode till genhd registration; however,
that involves rather big updates to percpu_ref which is difficult to
apply late in the devel cycle (v3.17-rc6 at the moment). As a
stop-gap measure till the proper fix can be implemented in the next
cycle, this patch introduces __percpu_ref_kill_expedited() and makes
blk_mq_freeze_queue() use it. This is heavy-handed but should work
for testing the experimental SCSI blk-mq implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christoph Hellwig <hch@infradead.org>
Link: http://lkml.kernel.org/g/20140919113815.GA10791@lst.de
Fixes: add703fda9 ("blk-mq: use percpu_ref for mq usage count")
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
