First set of patches for v5.16. ath11k getting most of new features
this time. Other drivers also have few new features, and of course the
usual set of fixes and cleanups all over.
Major changes:
rtw88
* support adaptivity for ETSI/JP DFS region
* 8821c: support RFE type4 wifi NIC
brcmfmac
* DMI nvram filename quirk for Cyberbook T116 tablet
ath9k
* load calibration data and pci init values via nvmem subsystem
ath11k
* include channel rx and tx time in survey dump statistics
* support for setting fixed Wi-Fi 6 rates from user space
* support for 80P80 and 160 MHz bandwidths
* spectral scan support for QCN9074
* support for calibration data files per radio
* support for calibration data via eeprom
* support for rx decapsulation offload (data frames in 802.3 format)
* support channel 2 in 6 GHz band
ath10k
* include frame time stamp in beacon and probe response frames
wcn36xx
* enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmFeqCYVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622b1+QIAKeCfq25i6ObhdgKP7etAHyaOupP
0wKxXwuOMLllwUSDp/1vyONqMgNbpurXlGzqcwG2fRyljZouuuzAM/WUxtSETVEC
TaXYhoX7+u0DuVZ+QvREL0fK+jBB2qbpRpAneNPQ+nvjND5dVm233NwZ4oG65Z4f
qQC21WeP6rfi870Bj5ycmGIWbb+OVT0B7FHfNzy5tSkcCFmlKZBfP7p6raUyy6/Z
0EBosxEd5FWjAHbWHXLGtXb+k/48ntcFyCswa9qMBjVawahgNfXGG1JwceHFMRvE
fwNMweWj4M5QVs7jBZoQaxijBXUPjJdp/2adybgIpgQp50FmlC8uyRSe9YQ=
=yAni
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
First set of patches for v5.16. ath11k getting most of new features
this time. Other drivers also have few new features, and of course the
usual set of fixes and cleanups all over.
Major changes:
rtw88
* support adaptivity for ETSI/JP DFS region
* 8821c: support RFE type4 wifi NIC
brcmfmac
* DMI nvram filename quirk for Cyberbook T116 tablet
ath9k
* load calibration data and pci init values via nvmem subsystem
ath11k
* include channel rx and tx time in survey dump statistics
* support for setting fixed Wi-Fi 6 rates from user space
* support for 80P80 and 160 MHz bandwidths
* spectral scan support for QCN9074
* support for calibration data files per radio
* support for calibration data via eeprom
* support for rx decapsulation offload (data frames in 802.3 format)
* support channel 2 in 6 GHz band
ath10k
* include frame time stamp in beacon and probe response frames
wcn36xx
* enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net: add a helpers for loading netdev->dev_addr from FW
We're trying to make all writes to netdev->dev_addr go via helpers.
A lot of places pass netdev->dev_addr to of_get_ethdev_address() and
device_get_ethdev_addr() so this set adds new functions which wrap
the functionality.
v2 performs suggested code moves, adds a couple additional clean ups
on the device property side, and an extra patch converting drivers
which can benefit from device_get_ethdev_address().
v3 removes OF_NET and corrects kdoc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a few drivers to device_get_ethdev_address(),
saving a few LoC.
The check if addr is valid in netsec is superfluous,
device_get_ethdev_addr() already checks that (in
fwnode_get_mac_addr()).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new device_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- device_get_mac_address(np, dev->dev_addr, ETH_ALEN)
+ device_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
There is a handful of drivers which pass netdev->dev_addr as
the destination buffer to device_get_mac_address(). Add a helper
which takes a dev pointer instead, so it can call an appropriate
helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass in ETH_ALEN and the function itself
will return -EINVAL for any other address length.
Just assume it's ETH_ALEN like all other mac address
helpers (nvm, of, platform).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fwnode_get_mac_address() and device_get_mac_address()
return a pointer to the buffer that was passed to them
on success or NULL on failure. None of the callers
care about the actual value, only if it's NULL or not.
These semantics differ from of_get_mac_address() which
returns an int so to avoid confusion make the device
helpers return an errno.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the mac address helpers out, eth.c already contains
a bunch of similar helpers.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
There are roughly 40 places where netdev->dev_addr is passed
as the destination to a of_get_mac_address() call. Add a helper
which takes a dev pointer instead, so it can call an appropriate
helper.
Note that of_get_mac_address() already assumes the address is
6 bytes long (ETH_ALEN) so use eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rob suggests to move of_net.c from under drivers/of/ somewhere
to the networking code.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rikard Falkeborn says:
====================
nfc: pn533: Constify ops-structs
Constify a couple of ops-structs. This allows the compiler to put the
static structs in read-only memory.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Neither the driver or the core modifies the pn533_phy_ops struct, so
make them const to allow the compiler to put the static structs in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only usage of pn532_serdev_ops is to pass its address to
serdev_device_set_client_ops(), which takes a pointer to const
serdev_device_ops as argument. Make it const to allow the compiler to
put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Add mdiobus_modify_changed() helper
Sean Anderson's recent patch series is introducing more read-write
operations on the MDIO bus that only need to happen if a change is
being made.
We have similar logic in __mdiobus_modify_changed(), but we didn't
add its correponding locked variant mdiobus_modify_changed() as we
had very few users. Now that we are getting more, let's add the
helper.
====================
Link: https://lore.kernel.org/r/YV2UIa2eU+UjmWaE@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the mdiobus_modify_changed() helper in the C22 PCS advertisement
helper.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add mdiobus_modify_changed() helper to reflect the phylib and similar
equivalents. This will avoid this functionality being open-coded, as
has already happened in phylink, and it looks like other users will be
appearing soon.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel says:
====================
ethtool: Add ability to control transceiver modules' power mode
This patchset extends the ethtool netlink API to allow user space to
control transceiver modules. Two specific APIs are added, but the plan
is to extend the interface with more APIs in the future (see "Future
plans").
This submission is a complete rework of a previous submission [1] that
tried to achieve the same goal by allowing user space to write to the
EEPROMs of these modules. It was rejected as it could have enabled user
space binary blob drivers.
However, the main issue is that by directly writing to some pages of
these EEPROMs, we are interfering with the entity that is controlling
the modules (kernel / device firmware). In addition, some functionality
cannot be implemented solely by writing to the EEPROM, as it requires
the assertion / de-assertion of hardware signals (e.g., "ResetL" pin in
SFF-8636).
Motivation
==========
The kernel can currently dump the contents of module EEPROMs to user
space via the ethtool legacy ioctl API or the new netlink API. These
dumps can then be parsed by ethtool(8) according to the specification
that defines the memory map of the EEPROM. For example, SFF-8636 [2] for
QSFP and CMIS [3] for QSFP-DD.
In addition to read-only elements, these specifications also define
writeable elements that can be used to control the behavior of the
module. For example, controlling whether the module is put in low or
high power mode to limit its power consumption.
The CMIS specification even defines a message exchange mechanism (CDB,
Command Data Block) on top of the module's memory map. This allows the
host to send various commands to the module. For example, to update its
firmware.
Implementation
==============
The ethtool netlink API is extended with two new messages,
'ETHTOOL_MSG_MODULE_SET' and 'ETHTOOL_MSG_MODULE_GET', that allow user
space to set and get transceiver module parameters. Specifically, the
'ETHTOOL_A_MODULE_POWER_MODE_POLICY' attribute allows user space to
control the power mode policy of the module in order to limit its power
consumption. See detailed description in patch #1.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the kernel.
Testing and introspection
=========================
See detailed description in patches #1 and #5.
Patchset overview
=================
Patch #1 adds the initial infrastructure in ethtool along with the
ability to control transceiver modules' power mode.
Patches #2-#3 add required device registers in mlxsw.
Patch #4 implements in mlxsw the ethtool operations added in patch #1.
Patch #5 adds extended link states in order to allow user space to
troubleshoot link down issues related to transceiver modules.
Patch #6 adds support for these extended states in mlxsw.
Future plans
============
* Extend 'ETHTOOL_MSG_MODULE_SET' to control Tx output among other
attributes.
* Add new ethtool message(s) to update firmware on transceiver modules.
* Extend ethtool(8) to parse more diagnostic information from CMIS
modules. No kernel changes required.
[1] https://lore.kernel.org/netdev/20210623075925.2610908-1-idosch@idosch.org/
[2] https://members.snia.org/document/dl/26418
[3] http://www.qsfp-dd.com/wp-content/uploads/2021/05/CMIS5p0.pdf
Previous versions:
[4] https://lore.kernel.org/netdev/20211003073219.1631064-1-idosch@idosch.org/
[5] https://lore.kernel.org/netdev/20210824130344.1828076-1-idosch@idosch.org/
[6] https://lore.kernel.org/netdev/20210818155202.1278177-1-idosch@idosch.org/
[7] https://lore.kernel.org/netdev/20210809102152.719961-1-idosch@idosch.org/
====================
Link: https://lore.kernel.org/r/20211006104647.2357115-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the transceiver module extended state and sub-state
added in previous patch. The extended state is meant to describe link
issues related to transceiver modules.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an extended state and sub-state to describe link issues related to
transceiver modules.
The 'ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY' extended sub-state
tells user space that port is unable to gain a carrier because the CMIS
Module State Machine did not reach the ModuleReady (Fully Operational)
state. For example, if the module is stuck at ModuleLowPwr or
ModuleFault state. In case of the latter, user space can read the fault
reason from the module's EEPROM and potentially reset it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement support for ethtool_ops::.get_module_power_mode and
ethtool_ops::set_module_power_mode.
The get operation is implemented using the Management Cable IO and
Notifications (MCION) register that reports the operational power mode
of the module and its presence. In case a module is not present, its
operational power mode is not reported to ethtool and user space. If not
set before, the power mode policy is reported as "high", which is the
default on Mellanox systems.
The set operation is implemented using the Port Module Memory Map
Properties (PMMP) register. The register instructs the device's firmware
to transition a plugged-in module to / out of low power mode by writing
to its memory map.
When the power mode policy is set to 'auto', a module will not
transition to low power mode as long as any ports using it are
administratively up. Example:
# devlink port split swp11 count 4
# ethtool --set-module swp11s0 power-mode-policy auto
$ ethtool --show-module swp11s0
Module parameters for swp11s0:
power-mode-policy auto
power-mode low
# ip link set dev swp11s0 up
# ip link set dev swp11s1 up
$ ethtool --show-module swp11s0
Module parameters for swp11s0:
power-mode-policy auto
power-mode high
# ip link set dev swp11s1 down
$ ethtool --show-module swp11s0
Module parameters for swp11s0:
power-mode-policy auto
power-mode high
# ip link set dev swp11s0 down
$ ethtool --show-module swp11s0
Module parameters for swp11s0:
power-mode-policy auto
power-mode low
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the Management Cable IO and Notifications register. It will be used
to retrieve the power mode status of a module in subsequent patches and
whether a module is present in a cage or not.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the Port Module Memory Map Properties register. It will be used to
set the power mode of a module in subsequent patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and
'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver
modules parameters and retrieve their status.
The first parameter to control is the power mode of the module. It is
only relevant for paged memory modules, as flat memory modules always
operate in low power mode.
When a paged memory module is in low power mode, its power consumption
is reduced to the minimum, the management interface towards the host is
available and the data path is deactivated.
User space can choose to put modules that are not currently in use in
low power mode and transition them to high power mode before putting the
associated ports administratively up. This is useful for user space that
favors reduced power consumption and lower temperatures over reduced
link up times. In QSFP-DD modules the transition from low power mode to
high power mode can take a few seconds and this transition is only
expected to get longer with future / more complex modules.
User space can control the power mode of the module via the power mode
policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible
values:
* high: Module is always in high power mode.
* auto: Module is transitioned by the host to high power mode when the
first port using it is put administratively up and to low power mode
when the last port using it is put administratively down.
The operational power mode of the module is available to user space via
the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not
reported to user space when a module is not plugged-in.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the CPU.
CMIS testing
============
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
The module is not in low power mode, as it is not forced by hardware
(LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off).
The power mode can be queried from the kernel. In case
LowPwrAllowRequestHW was on, the kernel would need to take into account
the state of the LowPwrRequestHW signal, which is not visible to user
space.
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp11 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp11 up
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp11 down
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
SFF-8636 testing
================
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm
Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm
Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm
Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm
Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm
Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm
Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm
The module is not in low power mode, as it is not forced by hardware
(Power override is on) or by software (Power set is off).
The power mode can be queried from the kernel. In case Power override
was off, the kernel would need to take into account the state of the
LPMode signal, which is not visible to user space.
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp13 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp13 up
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm
Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm
Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm
Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm
Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm
Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm
Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp13 down
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a spelling mistake in a DP_VERBOSE message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static checkers and runtime checkers such as KMSan will complain that
we do not initialize the last 6 bytes of "cb_priv". The caller only
uses the first two bytes so it doesn't cause a runtime issue. Still
worth fixing though.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dst_update_pmtu_no_confirm() is a just wrapper function of
->update_pmtu(). So, it doesn't change logic
Signed-off-by: Gyeongun Kang <kyeongun15@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err variable is checked for true or false a few lines above. When
!err is checked again, it always evaluates to true. Therefore we should
skip this check.
We should also group the adjacent statements together for readability.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij says:
====================
RTL8366RB enhancements
This patch set is a set of reasonably mature improvements
for the RTL8366RB switch, implemented after Vladimir
challenged me to dig deeper into the switch functions.
ChangeLog v4->v5:
- Drop dubious flood control patch: these registers probably
only deal with rate limiting, we will deal with this
another time if we can figure it out.
ChangeLog -> v4:
- Rebase earlier circulated patches on the now merged
VLAN set-up cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for setting the STP state to the RTL8366RB
DSA switch. This rids the following message from the kernel on
e.g. OpenWrt:
DSA: failed to set STP state 3 (-95)
Since the RTL8366RB has one STP state register per FID with
two bit per port in each, we simply loop over all the FIDs
and set the state on all of them.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements fast aging per-port using the special "security"
register, which will flush any learned L2 LUT entries on a port.
The vendor API just enabled setting and clearing this bit, so
we set it to age out any entries on the port and then we clear
it again.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8366RB hardware supports disabling learning per-port
so let's make use of this feature. Rename some unfortunately
named registers in the process.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the embedded fast-ethernet PHY found on the QCA9561
WiSoC platform. It supports the usual Atheros PHY featureset including
the cable tester.
Tested on a Xiaomi MiRouter 4Q (QCA9561)
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20211005225401.10653-1-mail@david-bauer.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Add support for MediaTek MT7922 and MT7921
- Enable support for AOSP extention in Qualcomm WCN399x and Realtek
8822C/8852A.
- Add initial support for link quality and audio/codec offload.
- Rework of sockets sendmsg to avoid locking issues.
- Add vhci suspend/resume emulation.
-----BEGIN PGP SIGNATURE-----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=QRkQ
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2021-10-01' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for MediaTek MT7922 and MT7921
- Enable support for AOSP extention in Qualcomm WCN399x and Realtek
8822C/8852A.
- Add initial support for link quality and audio/codec offload.
- Rework of sockets sendmsg to avoid locking issues.
- Add vhci suspend/resume emulation.
====================
Link: https://lore.kernel.org/r/20211001230850.3635543-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert usb drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
Manually checked these are either usbnet or pure etherdevs.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
mlx4: prep for constant dev->dev_addr
This patch converts mlx4 for dev->dev_addr being const. It converts
to use of common helpers but also removes some seemingly unnecessary
idiosyncrasies.
Please review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->dev_addr will become const soon. Make sure all
functions which pass it around mark appropriate args
as const.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_u64_to_mac() takes the dev->dev_addr pointer and writes
to it byte by byte. It also clears the two bytes _after_ ETH_ALEN
which seems unnecessary. dev->addr_len is set to ETH_ALEN just
before the call.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_u64_to_mac() predates the common helper but doesn't
make the argument constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_mac_to_u64() predates and opencodes ether_addr_to_u64().
It doesn't make the argument constant so it'll be problematic
when dev->dev_addr becomes a const. Convert to the generic helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No users in tree since commit a3498436b3 ("netns: restrict uevents"),
so remove this functionality.
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Misc updates for mlx5 driver
1) Add TX max rate support for MQPRIO channel mode
2) Trivial TC action and modify header refactoring
3) TC support for accept action in fdb offloads
4) Allow single IRQ for PCI functions
5) Bridge offload: Pop PVID VLAN header on egress miss
Vlad Buslov says:
=================
With current architecture of mlx5 bridge offload it is possible for a
packet to match in ingress table by source MAC (resulting VLAN header push
in case of port with configured PVID) and then miss in egress table when
destination MAC is not in FDB. Due to the lack of hardware learning in
NICs, this, in turn, results packet going to software data path with PVID
VLAN already added by hardware. This doesn't break software bridge since it
accepts either untagged packets or packets with any provisioned VLAN on
ports with PVID, but can break ingress TC, if affected part of Ethernet
header is matched by classifier.
Improve compatibility with software TC by restoring the packet header on
egress miss. Effectively, this change implements atomicity of mlx5 bridge
offload implementation - packet is either modified and redirected to
destination port or appears unmodified in software.
=================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmFbpiEACgkQSD+KveBX
+j4rjQf/a1UTqBH31Rh3+zr71yAhfsEYHdSogdPe1oo9zA4IvDZ0uwwdBNPNjzYa
ZTcDPKmHgbi6UUqokpmWHYDieXNsZz95lPWS0/QcySgnSag9keGpS2I1y9KtvurH
MkejWuCUD1UniPPIw02F1AJ3hNOLjDst8gydyt2T52lqxHX9xprcgxAXcUPkGCsW
7jw+g5F6hbahgh1fFdBERqdLmvJiv2i0gmo5XEIYr5lQePqba43B4EQNKZkSQ/91
Gz8537wCHixW4q2e81m60b0olXrG65JTQAj+ckUUR8VbHwxCBbM5jzOZZXw9FXbB
hebTL+GflwbmshVWluXLlSKLu2gBaw==
=iVdj
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-10-04' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-10-04
Misc updates for mlx5 driver
1) Add TX max rate support for MQPRIO channel mode
2) Trivial TC action and modify header refactoring
3) TC support for accept action in fdb offloads
4) Allow single IRQ for PCI functions
5) Bridge offload: Pop PVID VLAN header on egress miss
Vlad Buslov says:
=================
With current architecture of mlx5 bridge offload it is possible for a
packet to match in ingress table by source MAC (resulting VLAN header push
in case of port with configured PVID) and then miss in egress table when
destination MAC is not in FDB. Due to the lack of hardware learning in
NICs, this, in turn, results packet going to software data path with PVID
VLAN already added by hardware. This doesn't break software bridge since it
accepts either untagged packets or packets with any provisioned VLAN on
ports with PVID, but can break ingress TC, if affected part of Ethernet
header is matched by classifier.
Improve compatibility with software TC by restoring the packet header on
egress miss. Effectively, this change implements atomicity of mlx5 bridge
offload implementation - packet is either modified and redirected to
destination port or appears unmodified in software.
=================
=================
Signed-off-by: David S. Miller <davem@davemloft.net>
Check ethernet controller DT node for "mdio" subnode and use it with
of_mdiobus_register() when present. That allows specifying MDIO and its
PHY devices in a standard DT based way.
This is required for BCM53573 SoC support. That family is sometimes
called Northstar (by marketing?) but is quite different from it. It uses
different CPU(s) and many different hw blocks.
One of shared blocks in BCM53573 is Ethernet controller. Switch however
is not SRAB accessible (as it Northstar) but is MDIO attached.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use info from DT if available
It allows describing for example a fixed link. It's more accurate than
just guessing there may be one (depending on a chipset).
2. Verify PHY ID before trying to connect PHY
PHY addr 0x1e (30) is special in Broadcom routers and means a switch
connected as MDIO devices instead of a real PHY. Don't try connecting to
it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to cast the pointer, unlike memcpy() eth_hw_addr_set()
does not take void *. The driver already casts &port->mac_addr
to u8 * in other places.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: a96d317fb1 ("ethernet: use eth_hw_addr_set()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
