In xhci_urb_enqueue(), allocate a block of memory for all the TDs instead
of allocating memory for each of them separately. This reduces the number
of kzalloc calling when an isochronous usb is submitted.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the xHCI driver always return a status value of zero for isochronous
URBs, when the last TD of an isochronous URB is short, the local variable
"status" stays set to -EINPROGRESS. When xHCI driver debugging is turned on,
this causes the log file to fill with messages like this:
[ 38.859282] xhci_hcd 0000:00:14.0: Giveback URB ffff88013ad47800, len = 1408, expected = 580, status = -115
Don't print out the status of an URB for isochronous URBs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI host controller in the Intel Panther Point chipset needs to have
software check whether new devices will fit in the available bus
bandwidth. Activate the software bandwidth checking quirk when we find
the right PCI device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that we have a bandwidth interval table per root port or TT that
describes the endpoint bandwidth information, we can finally use it to
check whether the bus bandwidth is oversubscribed for a new device
configuration/alternate interface setting.
The complication for this algorithm is that the bit of hardware logic that
creates the bus schedule is only 12-bit logic. In order to make sure it
can represent the maximum bus bandwidth in 12 bits, it has to convert the
endpoint max packet size and max esit payload into "blocks" (basically a
less-precise representation). The block size for each speed of device is
different, aside from low speed and full speed. In order to make sure we
don't allow a setup where the scheduler might fail, we also have to do the
bandwidth checking in blocks.
After checking that the endpoints fit in the schedule, we store the
bandwidth used for this root port or TT. If this is a FS/LS device under
an external HS hub, we also update the TT bandwidth and the root port
bandwidth (if this is a newly activated or deactivated TT).
I won't go into the details of the algorithm, as it's pretty well
documented in the comments.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to update the root port or TT's bandwidth interval table, we will
need to keep track of a list of endpoints, per interval. That way we can
easily know the new largest max packet size when we have to remove an
endpoint.
Add an endpoint list for each root port or TT structure, sorted by
endpoint max packet size. Insert new endpoints into the list such that
the head of the list always has the endpoint with the greatest max packet
size. Only insert endpoints and update the interval table with new
information when those endpoints are periodic.
Make sure to update the number of active TTs when we add or drop periodic
endpoints. A TT is only considered active if it has one or more periodic
endpoints attached (control and bulk are best effort, and counted in the
20% reserved on the high speed bus). If the number of active endpoints
for a TT was zero, and it's now non-zero, increment the number of active
TTs for the rootport. If the number of active endpoints was non-zero, and
it's now zero, decrement the number of active TTs.
We have to be careful when we're checking the bandwidth for a new
configuration/alt setting. If we don't have enough bandwidth, we need to
be able to "roll back" the bandwidth information stored in the endpoint
and the root port/TT interval bandwidth table. We can't just create a
copy of the interval bandwidth table, modify it, and check the bandwidth
with the copy because we have lists of endpoints and entries can't be on
more than one list. Instead, we copy the old endpoint bandwidth
information, and use it to revert the interval table when the bandwidth
check fails.
We don't check the bandwidth after endpoints are dropped from the interval
table when a device is reset or freed after a disconnect, because having
endpoints use less bandwidth should not push the bandwidth usage over the
limits. Besides which, we can't fail a device disconnect.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the upcoming patches, we'll use some stored endpoint information to
make software keep track of the worst-case bandwidth schedule. We need to
store several variables associated with each periodic endpoint:
- the type of endpoint
- Max Packet Size
- Mult
- Max ESIT payload
- Max Burst Size (aka number of packets, stored in one-based form)
- the endpoint interval (normalized to powers of 2 microframes)
All this information is available to the hardware, and stored in its
device output context. However, we need to ensure that the new
information is stored before the xHCI driver drops the xhci->lock to wait
on the Configure Endpoint command, so that another driver requesting a
configuration or alt setting change will see the update. The Configure
Endpoint command will never fail on the hardware that needs this software
bandwidth checking (assuming the slot is enabled and the flags are set
properly), so updating the endpoint info before the command completes
should be fine.
Until we add in the bandwidth checking code, just update the endpoint
information after the Configure Endpoint command completes, and after a
Reset Device command completes. Don't bother to clear the endpoint
bandwidth info when a device is being freed, since the xhci_virt_ep is
just going to be freed anyway.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For upcoming patches, we need to keep information about the bandwidth
domains under the xHCI host. Each root port is a separate primary
bandwidth domain, and each high speed hub's TT (and potentially each port
on a multi-TT hub) is a secondary bandwidth domain.
If the table were in text form, it would look a bit like this:
EP Interval Sum of Number Largest Max Max Packet
of Packets Packet Size Overhead
0 N mps overhead
...
15 N mps overhead
Overhead is the maximum packet overhead (for bit stuffing, CRC, protocol
overhead, etc) for all the endpoints in this interval. Devices with
different speeds have different max packet overhead. For example, if
there is a low speed and a full speed endpoint that both have an interval
of 3, we would use the higher overhead (the low speed overhead). Interval
0 is a bit special, since we really just want to know the sum of the max
ESIT payloads instead of the largest max packet size. That's stored in
the interval0_esit_payload variable. For root ports, we also need to keep
track of the number of active TTs.
For each root port, and each TT under a root port, store some information
about the bandwidth consumption. Dynamically allocate an array of root
port bandwidth information for the number of root ports on the xHCI host.
Each root port stores a list of TTs under the root port. A single TT hub
only has one entry in the list, but a multi-TT hub will have an entry per
port.
When the USB core says that a USB device is a hub, create one or more
entries in the root port TT list for the hub. When a device is deleted,
and it is a hub, search through the root port TT list and delete all
TT entries for the hub. Keep track of which TT entry is associated with a
device under a TT.
LS/FS devices attached directly to the root port will have usb_device->tt
set to the roothub. Ignore that, and treat it like a primary bandwidth
domain, since there isn't really a high speed bus between the roothub and
the host.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the xHCI driver now has split USB2/USB3 roothubs, devices under each
roothub can have duplicate "fake" port numbers. For the next set of
patches, we need to keep track of the "real" port number that the xHCI
host uses to index into the port status arrays.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the code to check whether we've reached the host controller's limit
on the number of endpoints out of the two conditional statements, to
remove duplicate code.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "port" field in xhci_virt_dev stores the port number associated with
one of the two xHCI split roothubs, not the unique port number the xHCI
hardware uses. Since we'll need to store the real hardware port number in
future patches, rename this field to "fake_port".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some alternate interface settings have no endpoints associated with them.
This shows up in some USB webcams, particularly the Logitech HD 1080p,
which uses the uvcvideo driver. If a driver switches between two alt
settings with no endpoints, there is no need to issue a configure endpoint
command, because there is no endpoint information to update.
The only time a configure endpoint command with just the add slot flag set
makes sense is when the driver is updating hub characteristics in the slot
context. However, that code never calls xhci_check_bandwidth, so we
should be safe not issuing a command if only the slot context add flag is
set.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
- Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: Fix wrong initializer for "locked" variable in assert_panel_unlocked
i915: do not setup intel_backlight twice
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: ftdi_sio: add Calao reference board support
USB option driver K3765/K4505 avoid CDC_DATA interface
USB: option: add YUGA device id to driver
usb: s5p-ehci: fix a NULL pointer deference
USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume().
USB option driver add PID of Huawei Vodafone K4605
USB option driver add PID of Huawei Vodafone K3806
xhci: Handle zero-length isochronous packets.
USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
usb: musb: gadget: fix error path
usb: gadget: f_phonet: unlock in error case
usb: musb: blackfin: include prefetch head file
usb: musb: tusb6010: fix compilation
usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h
usb: musb: cppi: fix build errors due to DBG and missing musb variable
usb: musb: ux500: replace missing DBG with dev_dbg
usb: musb: ux500: set dma config for both src and dst
usb: musb: fix oops on musb_gadget_pullup
usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1)
usb: gadget: hid: don't STALL when processing a HID Descriptor request
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
omap-serial: Allow IXON and IXOFF to be disabled.
TTY: serial, document ignoring of uart->ops->startup error
TTY: pty, fix pty counting
8250: Fix race condition in serial8250_backup_timeout().
serial/8250_pci: delete duplicate data definition
8250_pci: add support for Rosewill RC-305 4x serial port card
tty: Add "spi:" prefix for spi modalias
atmel_serial: fix atmel_default_console_device
serial: 8250_pnp: add Intermec CV60 touchscreen device
drivers/serial/ucc_uart.c: Fix compiler warning
pch_uart: Set PCIe bus number using probe parameter
serial: samsung: Fix build error
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] memory hotplug: only unassign assigned increments
[S390] Change default action from reipl to stop for on_restart
[S390] arch/s390/kernel/ipl.c: correct error detection check
[S390] drivers/s390/block/dasd_ioctl.c: add missing kfree
[S390] nss,initrd: kernel image and initrd must be in different segments
According to the SFI specification irq number 0xFF means device has no
interrupt or interrupt attached via GPIO.
Currently, we don't handle this special case and set irq field in
*_board_info structs to 255. It leads to confusion in some drivers.
Accelerometer driver tries to register interrupt 255, fails and prints
"Cannot get IRQ" to dmesg.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (32 commits)
ALSA: hda: Conexant: Allow different output types to share DAC
ASoC: Correct element count for WM8996 sidetone HPF
ASoC: Tegra: wm8903 machine driver: Drop Ventana support
ASoC: Add samsung maintainer
ASoC: Add Springbank I/O card to Speyside Kconfig
ALSA: hda/conexant - Enable ADC-switching for auto-mic mode, too
ALSA: hda - Fix double-headphone/speaker paths for Cxt auto-parser
ALSA: hda - Update jack-sense info even when no automute is set
ALSA: hda - Fix output-path initialization for Realtek auto-parser
sound/soc/fsl/mpc8610_hpcd.c: add missing of_node_put
sound/soc/fsl/p1022_ds.c: add missing of_node_put
sound/soc/ep93xx/ep93xx-i2s.c: add missing kfree
sound/soc/kirkwood/kirkwood-i2s.c: add missing kfree
ASoC: soc-core: use GFP_KERNEL flag for kmalloc in snd_soc_cnew
sound/soc/fsl/fsl_dma.c: add missing of_node_put
ASoC: Clear completions from late WM8996 FLL lock IRQs
ASoC: Clear any outstanding WM8962 FLL lock completions before waiting
ASoC: Ensure we only run Speyside WM8962 bias level callbacks once
ASoC: Fix configuration of WM8996 input enables
ASoC: WM8996 record paths need AIFCLK
...
This bug causes the IECSR register clear failure. In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared. So the related ISR may be called persistently.
The RETE bit in IECSR is cleared by writing a 1 to it.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous rtc-s3c had two issues related with its IRQ.
1. Users cannot open rtc multiple times because an open operation
calls request_irq on the same IRQ. (e.g., two user processes wants to
open and read RTC time from rtc-s3c at the same time)
2. If alarm is set and no one has the rtc opened with filesystem
(either the alarm is set by kernel/boot-loader or user set an alarm and
closed rtc dev file), the pending bit is not cleared and no further
interrupt is invoked. When the alarm is used by the system itself such
as a resume from suspend-to-RAM or other Low-power modes/idle, this is
a critical issue.
This patch mitigates these issues by calling request_irq at probe and
free_irq at remove.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bd2802_unregister_led_classdev() should unregister all registered
instances of led_classdev class that had registered by
bd2802_register_led_classdev().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kim Kyuwon <q1.kim@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following build errors:
drivers/tty/serial/8250_early.c:160: error: 'BASE_BAUD' undeclared (first use in this function): 1 errors in 1 logs
drivers/tty/serial/8250_early.c:37:24: error: asm/serial.h: No such file or directory: 1 errors in 1 logs
I am not sure if (1843200 / 16) is suitable for cris, but most other
arch's define it as this value.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 43cc71eed1 ("platform: prefix MODALIAS with "platform:""), the
platform modalias is prefixed with "platform:".
This patch changes the MODULE_ALIAS to "platform:ab8500-pwm".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Arun Murthy <arun.murthy@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure we are passing the same cookie in all calls to
request_threaded_irq() and free_irq().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an i2c driver, not a platform driver, thus use "i2c" prefix for
the module alias.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need a callback to do some things after pwm_enable, pwm_disable
and pwm_config.
Signed-off-by: Dilan Lee <dilee@nvidia.com>
Reviewed-by: Robert Morell <rmorell@nvidia.com>
Reviewed-by: Arun Murthy <arun.murthy@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 79dfdaccd1 ("memcg: make oom_lock 0 and 1 based rather than
counter") tried to oom lock the hierarchy and roll back upon
encountering an already locked memcg.
The code is confused when it comes to detecting a locked memcg, though,
so it would fail and rollback after locking one memcg and encountering
an unlocked second one.
The result is that oom-locking hierarchies fails unconditionally and
that every oom killer invocation simply goes to sleep on the oom
waitqueue forever. The tasks practically hang forever without anyone
intervening, possibly holding locks that trip up unrelated tasks, too.
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing include of linux/module.h for drivers that use interfaces from
linux/module.h. This patch fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ep93xx_bl.c uses interfaces from linux/module.h, so it should include
that file. This patch fixes build errors:
CC [M] drivers/video/backlight/ep93xx_bl.o
drivers/video/backlight/ep93xx_bl.c:138: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/video/backlight/ep93xx_bl.c:158: error: expected declaration specifiers or '...' before string constant
drivers/video/backlight/ep93xx_bl.c:158: warning: data definition has no type or storage class
...
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace/remove use of RIO v.1.2 registers/bits that are not
forward-compatible with newer versions of RapidIO specification.
RapidIO specification v.1.3 removed Write Port CSR, Doorbell CSR,
Mailbox CSR and Mailbox and Doorbell bits of the PEF CAR.
Use of removed (since RIO v.1.3) register bits affects users of
currently available 1.3 and 2.x compliant devices who may use not so
recent kernel versions.
Removing checks for unsupported bits makes corresponding routines
compatible with all versions of RapidIO specification. Therefore,
backporting makes stable kernel versions compliant with RIO v.1.3 and
later as well.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Chul Kim <chul.kim@idt.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ZONE_CONGESTED is only cleared in kswapd, but pages can be freed in any
task. It's possible ZONE_CONGESTED isn't cleared in some cases:
1. the zone is already balanced just entering balance_pgdat() for
order-0 because concurrent tasks free memory. In this case, later
check will skip the zone as it's balanced so the flag isn't cleared.
2. high order balance fallbacks to order-0. quote from Mel: At the
end of balance_pgdat(), kswapd uses the following logic;
If reclaiming at high order {
for each zone {
if all_unreclaimable
skip
if watermark is not met
order = 0
loop again
/* watermark is met */
clear congested
}
}
i.e. it clears ZONE_CONGESTED if it the zone is balanced. if not,
it restarts balancing at order-0. However, if the higher zones are
balanced for order-0, kswapd will miss clearing ZONE_CONGESTED as
that only happens after a zone is shrunk. This can mean that
wait_iff_congested() stalls unnecessarily.
This patch makes kswapd clear ZONE_CONGESTED during its initial
highmem->dma scan for zones that are already balanced.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems that 7bf693951a ("console: allow to retain boot console via
boot option keep_bootcon") doesn't always achieve what it aims, as when
printk_late_init() runs it unconditionally turns off all boot consoles.
With this patch, I am able to see more messages on the boot console in
KVM guests than I can without, when keep_bootcon is specified.
I think it is appropriate for the relevant -stable trees. However, it's
more of an annoyance than a serious bug (ideally you don't need to keep
the boot console around as console handover should be working -- I was
encountering a situation where the console handover wasn't working and
not having the boot console available meant I couldn't see why).
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <gregkh@suse.de>
Acked-by: Fabio M. Di Nitto <fdinitto@redhat.com>
Cc: <stable@kernel.org> [2.6.39.x, 3.0.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul said: I left Google at the end of last week - if it's not bouncing
already, menage@google.com isn't going to work for much longer.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Paul Menage <paul@paulmenage.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I get the below warning:
BUG: using smp_processor_id() in preemptible [00000000] code: bash/746
caller is native_sched_clock+0x37/0x6e
Pid: 746, comm: bash Tainted: G W 3.0.0+ #254
Call Trace:
[<ffffffff813435c6>] debug_smp_processor_id+0xc2/0xdc
[<ffffffff8104158d>] native_sched_clock+0x37/0x6e
[<ffffffff81116219>] try_to_free_mem_cgroup_pages+0x7d/0x270
[<ffffffff8114f1f8>] mem_cgroup_force_empty+0x24b/0x27a
[<ffffffff8114ff21>] ? sys_close+0x38/0x138
[<ffffffff8114ff21>] ? sys_close+0x38/0x138
[<ffffffff8114f257>] mem_cgroup_force_empty_write+0x17/0x19
[<ffffffff810c72fb>] cgroup_file_write+0xa8/0xba
[<ffffffff811522d2>] vfs_write+0xb3/0x138
[<ffffffff8115241a>] sys_write+0x4a/0x71
[<ffffffff8114ffd9>] ? sys_close+0xf0/0x138
[<ffffffff8176deab>] system_call_fastpath+0x16/0x1b
sched_clock() can't be used with preempt enabled. And we don't need
fast approach to get clock here, so let's use ktime API.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The various basic memory allocation function return NULL, not an
ERR_PTR.
The semantic patch that makes this change is available in
scripts/coccinelle/null/eno.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Cc: Niranjana Vishwanathapura <nvishwan@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The test for bad usage of min_t() and max_t() is missing the --ignore
type. Add it.
Signed-off-by: Hui Zhu <teawater@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change to new git tree -
(git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git).
Signed-off-by: Ralf Thielow <ralf.thielow@googlemail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d1a05b6973 ("memcg do not try to drain per-cpu caches without
pages") added a drain_local_stock() call to a preemptible section.
The draining task looks up the cpu-local stock twice to set the
draining-flag, then to drain the stock and clear the flag again. If the
task is migrated to a different CPU in between, noone will clear the
flag on the first stock and it will be forever undrainable. Its charge
can not be recovered and the cgroup can not be deleted anymore.
Properly pin the task to the executing CPU while draining stocks.
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The for loop was looking for i <= 0 instead of i >= 0 so this function
never did anything. Also we started with i = NB_SYSFS_BIN_FILES instead
of "NB_SYSFS_BIN_FILES - 1" which is an off by one bug.
Reported-by: Bojan Prtvar <prtvar.b@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jean-Franois Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
