Move the duplicated DIV_ROUND_CLOSEST_ULL macro into the intel_drv.h
header file so that it can be shared between intel_display.c
and intel_panel.c.
Signed-off-by: U. Artie Eoff <ullysses.a.eoff@intel.com>
Reviewed-By: Joe Konno <joe.konno@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Improper truncated integer division in the scale() function causes
actual_brightness != brightness. This (partial) work-around should be
sufficient for a majority of use-cases, but it is by no means a complete
solution.
TODO: Determine how best to scale "user" values to "hw" values, and
vice-versa, when the ranges are of different sizes. That would be a
buggy scenario even with this work-around.
The issue was introduced in the following (v3.17-rc1) commit:
6dda730 drm/i915: respect the VBT minimum backlight brightness
Note that for easier backporting this commit adds a duplicated macro.
A follow-up cleanup patch rectifies this for 3.18+
v2: (thanks to Chris Wilson) clarify commit message, use rounded division
macro
v3: -DIV_ROUND_CLOSEST() fails to build with CONFIG_X86_32=y. (Jani)
-Use DIV_ROUND_CLOSEST_ULL() instead. (Damien)
-v1 and v2 originally authored by Joe Konno.
Signed-off-by: U. Artie Eoff <ullysses.a.eoff@intel.com>
Cc: stable@vger.kernel.org
Reviewed-By: Joe Konno <joe.konno@intel.com>
[danvet: Add backporting note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell and later silicon has added a new pixel replication register
to the pipe timings for each transcoder. Now in addition to the
DPLL_A_MD register for the pixel clock double, we also need to write
to the TRANS_MULT_n (0x6002c) register to double the pixel data. Writing
to the DPLL only double the pixel clock.
ver2: Macro name change from MULTIPLY to PIPE_MULTI. (Daniel)
ver3: Do not set pixel multiplier if transcoder is eDP (Ville)
ver4: Macro name change to PIPE_MULT and default else pixel_multiplier
Cc: Ville =?iso-8859-1?Q?Syrj=E4l=E4?= <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Appease checkpatch and move one hunk back into the right
place that git am misplace!?]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the GPU frequency isn't going to change don't spam dmesg with
debug messages about it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
sg_alloc_table_from_pages() can build us a table with coalesced ranges which
means we need to iterate over pages and not sg table entries when releasing
page references.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Barbalho, Rafael" <rafael.barbalho@intel.com>
Tested-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Remove unused local variable sg.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This reverts commit c76bb61a71.
It's apparently too broken so that Rodrigo submitted a patch to add a
config option for it. Given that the design is also ... suboptimal and
that I've only merged this to get lead engineers and managers off my
back for one second let's just revert this.
/me puts on combat gear again
It was worth a shot ...
References: http://mid.mail-archive.com/1411686380-1953-1-git-send-email-rodrigo.vivi@intel.com
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Daisy Sun <daisy.sun@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
as these have been fixed in production hw and hurt performance
if applied.
v2: adjust requested ring space (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83482
Tested-by: zhoujian <jianx.zhou@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If something while getting panel CRC this means that probably hw I/O error
so hw is busted and try again shouldn't help much.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based upon a patch from Deepak, but reworked to only apply on gen7+
and with the logic a bit clarified.
v2: Fix s/SHIFT/MASK/ fumble that Ville spotted.
Cc: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we believe that the device can cross cache domains in its prefetcher
(i.e. we allow neighbouring pages in different domains), we don't supply
a color_adjust callback. Use the presence of this callback to better
determine when we should be verifying that the GTT space we just
used is valid.
v2: Remove the superfluous struct drm_device function param as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Also adjust the comment per irc discussion with Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gen6 and earlier conflate address space selection (ppgtt vs ggtt) with
the security bit (i.e. only privileged batches were allowed to run from
ggtt). From Haswell only, you are able to select the security bit
separate from the address space - and we always requested to use ppgtt.
This breaks the golden render state batch execution with full-ppgtt as
that is only present in the global GTT and more generally any secure
batch that is not colocated in the ppgtt and ggtt. So we need to
disable the use of the ppgtt selector bit for secure batches, or else we
hang immediately upon boot and thence after every GPU reset...
v2: Only HSW differentiates between secure dispatch and ggtt, so simply
ignore the differentiation and always use secure==ggtt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rectify commit message as noted by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In chv, we have two power wells Render & Media. We need to use
corresponsing forcewake count. If we dont follow this we are getting
error "*ERROR*: Timed out waiting for forcewake old ack to clear" due to
multiple entry into __vlv_force_wake_get.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Requested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also here, i915_gem_evict_vm causes an unbind, which can end up dropping
the last ref to the ppgtt.
Triggered by igt gem_evict_everything test.
Testcase: igt/gem_evict_everything
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Chris Wilson <chris@cris-wilsonc.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow I've overlooked this when simplifying the irq reinit
scheme on gen4.5+ in
commit 78ad455fd2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu May 22 22:18:21 2014 +0200
drm/i915: Improve irq handling after gpu resets
Since display interrups in general survive a gpu reset on those
platforms there's also no need to reinit the hotplug settings.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_send_vblank_event() demands that we hold the event spinlock whilst
calling it, so do so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fix the double lock as requested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before we process the final unbind on an object and move it to the
unbound list, it is semantically cleaner if there are no more active
references to the object. (An active reference would imply that it was
still being accessed by the GPU after it became inaccessible.) The
caveat is that all callsites must be prepared for the object to
disappeared during the unbind - i.e. they must hold their own reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to the lazy retirement semantics, even though we have unbound an
object, it may still hold onto an active reference. So in the debug code,
play safe.
v2: Export i915_gem_shrink() rather than opencoding it.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP panels are generally designed to support only a single clock and
lane configuration.
commit 56071a2076
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue May 6 14:56:52 2014 +0300
drm/i915: use lane count and link rate from VBT as minimums for eDP
should have started using the optimal link parameters for eDP
panels. Turns out a certain other OS uses DPCD instead of VBT, which
means trusting VBT on this may not be so reliable after all. Follow
suit.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81647
Tested-by: Adam Jirasek <libm3l@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79386
Tested-by: Narthana Epa <narthana.epa+freedesktop@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This goes back to
commit 06ea66b6bb
Author: Todd Previte <tprevite@gmail.com>
Date: Mon Jan 20 10:19:39 2014 -0700
drm/i915: Enable 5.4Ghz (HBR2) link rate for Displayport 1.2-capable devices
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Pimp commit message a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Oops, apparently intel_hdmi/intel_dp is the encoder - an object with a
distinct lifetime to the connector, and so we cannot simply reuse the
common function to unset and free the edid.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
830 is very unhappy of the watermark value is too low (indicating a very
high watermark in fact, ie. memory fetch will occur with an almost full
FIFO). Limit the watermark value to at least 8 cache lines.
That also matches the burst size we use on most platforms. BSpec seems
to indicate we should limit the watermark to 'burst size + 1'. But on
gen4 we already use a hardcoded 8 as the watermark value (as the spec
says we should), so just use 8 as the limit on gen2/3 as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec says:
"For the correct operation of the muxed DVO pins (GDEVSELB/ I2Cdata,
GIRDBY/I2CClk) and (GFRAMEB/DVI_Data, GTRDYB/DVI_Clk): Bit 31
(DPLL VCO Enable) and Bit 30 (2X Clock Enable) must be set to “1” in
both the DPLL A Control Register (06014h-06017h) and DPLL B Control
Register (06018h-0601Bh)."
The pipe A and B force quirks take care of DPLL_VCO_ENABLE, so we
just need a bit of special care to handle DPLL_DVO_2X_MODE.
v2: Recompute num_dvo_pipes on the spot, use PIPE_A/PIPE_B instead
of pipe/!pipe for the register offsets in disable (Daniel)
Add a comment about the ordering in enable and another one
about filtering out the DVO 2x bit in state readout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Thomas Richter <richter@rus.uni-stuttgart.de> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit "drm/rcar-du: Use struct videomode in platform data" touches board code
in arch/arm/mach-shmobile. There is, to the best of my knowledge, no risk of
conflict for v3.18. Simon, are you fine with getting those changes merged
through Dave's tree (and could you confirm that no conflict should occur) ?
Simon acked the merge:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add OF support
drm/rcar-du: Use struct videomode in platform data
video: Add DT bindings for the R-Car Display Unit
video: Add THC63LVDM83D DT bindings documentation
video: Add ADV7123 DT bindings documentation
video: Add DT binding documentation for VGA connector
devicetree: Add vendor prefix "thine" to vendor-prefixes.txt
devicetree: Add vendor prefix "mitsubishi" to vendor-prefixes.txt
drm/shmob: Update copyright notice
drm/rcar-du: Update copyright notice
While zone->name is currently hard coded, the call to kobject_init_and_add()
should follow the more defensive argument list usage (as already done in
other places in ttm_memory.c) where "%s" is used instead of directly passing
in a variable as a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to support the "enable GPIO" available in many panel devices,
this commit adds a proper devicetree binding.
By providing an enable GPIO in the devicetree, the driver can now turn
off and on the panel device, and/or the backlight device. Both the
backlight and the GPIO are optional properties.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of setting an initial value for the return code, set it explicitly
on each error path. This is just a cosmetic cleanup, as preparation for the
enable GPIO support.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current backlight support is broken; the driver expects a backlight-class
in the panel devicetree node. Fix this by implementing it properly, getting
an optional backlight from a phandle.
This shouldn't cause any backward-compatibility DT issue because the current
implementation doesn't work and is not even documented.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Using the managed variant to allocate the resource makes the code simpler
and less error-prone.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just a cosmetic cleanup.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just a trivial cleanup to remove the variable.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds the missing calls to of_node_put to release the node
that's currently held by the of_get_child_by_name() call in the panel
info parsing code.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current error path calls tilcdc_unload() in case of an error to release
the resources. However, this is wrong because not all resources have been
allocated by the time an error occurs in tilcdc_load().
To fix it, this commit adds proper labels to bail out at the different
stages in the load function, and release only the resources actually allocated.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
Pull in first set of changes from Ben for ast on ppc.
I've done a quick boot test on x86 and it still seems to boot.
* 'drm-next-ast-fixes' of ssh://people.freedesktop.org/~/linux:
drm/ast: Cleanup analog init code path
drm/ast: Don't assume DVO enabled means SIL164 on uninitialized chips
drm/ast: Properly initialize P2A base before using it in ast_init_3rdtx()
drm/ast: POST chip at probe time if VGA not enabled
drm/ast: Try to use MMIO registers when PIO isn't supported
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
This is the main merge request for Nouveau 3.18, overview:
- various bits of roy's gt21x clock work
- various bits of kepler memory clock work (don't get too excited, there's at least one more major bit left that's busting higher freqs)
- misc fan control improvements
- kepler hdmi infoframe fixes
- dp audio
- l2 cache + cbc improvements
* 'linux-3.18' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (68 commits)
drm/gt214-/disp: enable dp audio
drm/gt214-/kms: fix hda eld regression
drm/g94-/disp: calculate some dp audio constants
drm/gt214-/kms: perform hda codec setup on displayport too
drm/gk104-/disp: infoframe registers moved yet again on kepler
drm/nouveau/bios: parse older ramcfg/timing data like we do newer ones
drm/nva3/fb/ram: Per-partition regs
drm/nouveau/fb/ram: Support strided regs
drm/nv50/fb/ram: Store the number of partitions in the designated fields
drm/nv50/kms: Set VBLANK time in modeset script
drm/nouveau/bios: Add rammap support for version 1.0
drm/gf100-/pwr/memx: block host and fifo around reclock
drm/nouveau/pwr/memx: fix command ordering around block/unblock
drm/nouveau/pwr/memx: rename fb off/on to block/unblock
drm/nva3/clk: Pause the GPU before reclocking
drm/nouveau/gpio: rename g92 class to g94
drm/gk104-/fb/ram: move fb enable/disable to same place as nvidia
drm/gk104/fb/ram: twiddle some more bits when reclocking
drm/nouveau/bios: parse another large chunk of random memory config data
drm/gk104-/fb/ram: perform certain steps only when bios data differs
...
NVIDIA appear to have tweaked the algorithm from GF110, this implements
the previous algorithm for them still.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Solves blinking on reclocking memory. The value set is an underestimate, but
with non-reduced vblanking this should give us plenty of time
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
