Commit Graph

204513 Commits

Author SHA1 Message Date
Jeff Kirsher
2d0bb1c1f4 e100/e1000*/igb*/ixgb*: Add missing read memory barrier
Based on patches from Sonny Rao and Milton Miller...

Combined the patches to fix up clean_tx_irq and clean_rx_irq.

The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.

In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.

The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.

This bug was found during stress testing and adding this barrier has
been shown to fix it.  The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().

This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.

Previously Submitted to e1000-devel only for ixgbe

http://marc.info/?l=e1000-devel&m=126593062701537&w=3

We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.

CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-08 20:02:45 -07:00
John Fastabend
4bc091d85f ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG
Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause
a build error.  This resolves the build error by wrapping
the fcoe.up in CONFIG_IXGBE_DCB ifdefs.

Also frames were being priority VLAN tagged even without DCB
enabled.  This fixes this so that 8021Q priority tags are
only added with DCB actually enabled.

Reported-by: divya <dipraksh@linux.vnet.ibm.com>
Reported-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-08 20:02:44 -07:00
Amit Kumar Salecha
16d884bd90 netxen: protect tx timeout recovery by rtnl lock
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07 23:05:23 -07:00
Dan Carpenter
8bcfbd0af0 isdn: gigaset: use after free
I moved the kfree(cb) below the dereferences.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07 23:04:12 -07:00
Dan Carpenter
7e27a0aeb9 isdn: gigaset: add missing unlock
We should unlock here.  This is the only place where we return from the
function with the lock held.  The caller isn't expecting it.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07 23:04:11 -07:00
David Woodhouse
1f6ea6e511 solos-pci: Fix race condition in tasklet RX handling
We were seeing faults in the solos-pci receive tasklet when packets
arrived for a VCC which was currently being closed:

[18842.727906] EIP: [<e082f490>] br2684_push+0x19/0x234 [br2684] SS:ESP 0068:dfb89d14 

[18845.090712] [<c13ecff3>] ? do_page_fault+0x0/0x2e1 
[18845.120042] [<e082f490>] ? br2684_push+0x19/0x234 [br2684] 
[18845.153530] [<e084fa13>] solos_bh+0x28b/0x7c8 [solos_pci] 
[18845.186488] [<e084f711>] ? solos_irq+0x2d/0x51 [solos_pci] 
[18845.219960] [<c100387b>] ? handle_irq+0x3b/0x48 
[18845.247732] [<c10265cb>] ? irq_exit+0x34/0x57 
[18845.274437] [<c1025720>] tasklet_action+0x42/0x69 
[18845.303247] [<c102643f>] __do_softirq+0x8e/0x129 
[18845.331540] [<c10264ff>] do_softirq+0x25/0x2a 
[18845.358274] [<c102664c>] _local_bh_enable_ip+0x5e/0x6a 
[18845.389677] [<c102666d>] local_bh_enable+0xb/0xe 
[18845.417944] [<e08490a8>] ppp_unregister_channel+0x32/0xbb [ppp_generic] 
[18845.458193] [<e08731ad>] pppox_unbind_sock+0x18/0x1f [pppox] 

This patch uses an RCU-inspired approach to fix it. In the RX tasklet's
find_vcc() function we first refuse to use a VCC which already has the
ATM_VF_READY bit cleared. And in the VCC close function, we synchronise
with the tasklet to ensure that it can't still be using the VCC before
we continue and allow the VCC to be destroyed.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Nathan Williams <nathan@traverse.com.au>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07 23:02:59 -07:00
Jarek Poplawski
eb4a5527b1 pkt_sched: Fix sch_sfq vs tcf_bind_filter oops
Since there was added ->tcf_chain() method without ->bind_tcf() to
sch_sfq class options, there is oops when a filter is added with
the classid parameter.

Fixes commit 7d2681a6ff
netdev thread: null pointer at cls_api.c

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Reported-by: Franchoze Eric <franchoze@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07 22:45:41 -07:00
Changli Gao
cece1945bf net: disable preemption before call smp_processor_id()
Although netif_rx() isn't expected to be called in process context with
preemption enabled, it'd better handle this case. And this is why get_cpu()
is used in the non-RPS #ifdef branch. If tree RCU is selected,
rcu_read_lock() won't disable preemption, so preempt_disable() should be
called explictly.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07 20:35:43 -07:00
Dmitry Popov
ba78e2ddca tcp: no md5sig option size check bug
tcp_parse_md5sig_option doesn't check md5sig option (TCPOPT_MD5SIG)
length, but tcp_v[46]_inbound_md5_hash assume that it's at least 16
bytes long.

Signed-off-by: Dmitry Popov <dp@highloadlab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-07 20:24:28 -07:00
David S. Miller
e225567960 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2010-08-06 13:30:43 -07:00
Johannes Berg
a24d52f390 iwlwifi: fix locking assertions
spin_is_locked() can return zero on some (UP?)
configurations because locks don't exist, and
that causes an endless amount of warnings. Use
lockdep_assert_held() instead, which has two
advantages:
 1) it verifies the current task is holding
    the lock or mutex
 2) it compiles away completely when lockdep
    is not enabled

Cc: stable@kernel.org [2.6.34+, maybe only parts of patch]
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-06 13:53:58 -04:00
Johannes Berg
e95b743536 iwlwifi: fix TX tracer
The TX tracing code copies with the wrong length,
which will typically copy too little data. Fix
this by using the correct length variable.

Cc: stable@kernel.org [2.6.32+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-06 13:53:58 -04:00
Dan Carpenter
4b030d4288 isdn: fix information leak
The main motivation of this patch changing strcpy() to strlcpy().
We strcpy() to copy a 48 byte buffers into a 49 byte buffers.  So at
best the last byte has leaked information, or maybe there is an
overflow?  Anyway, this patch closes the information leaks by zeroing
the memory and the calls to strlcpy() prevent overflows.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-05 13:21:25 -07:00
Jarek Poplawski
ce9e76c845 net: Fix napi_gro_frags vs netpoll path
The netpoll_rx_on() check in __napi_gro_receive() skips part of the
"common" GRO_NORMAL path, especially "pull:" in dev_gro_receive(),
where at least eth header should be copied for entirely paged skbs.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-05 13:21:25 -07:00
Christian Samsel
23d23e409a usbnet: remove noisy and hardly useful printk
With turned on hspa modem (Dell 5530 internal card) and activated usb auto
suspend, my system gets up 100 "usbnet_resume has delayed data" per
minute. I didnt noticed any pathological behaviour, so just drop
this message. if any objections, please at least change it to _DEBUG.

Signed-off-by: Christian Samsel <christian.samsel@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-05 13:21:24 -07:00
John W. Linville
8f1d2d2be7 rtl8180: avoid potential NULL deref in rtl8180_beacon_work
ieee80211_beacon_get can return NULL...

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
2010-08-05 16:05:27 -04:00
Sujith
c5d2711cb5 ath9k: Remove myself from the MAINTAINERS list
So long.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05 16:05:27 -04:00
Dan Williams
cc02681923 libertas: scan before assocation if no BSSID was given
Fix this leftover TODO from the cfg80211 conversion by doing a scan
if cfg80211 didn't pass in the BSSID for us.  Since the scan code
uses so much of the cfg80211_scan_request structure to build up the
firmware command, we just fake one when the scan request is triggered
internally.  But we need to make sure that internal 'fake' cfg82011
scan request does not get back to cfg82011 via cfg80211_scan_done().

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05 16:05:27 -04:00
Dan Williams
1975753937 libertas: fix association with some APs by using extended rates
Some APs get pissy if you don't send the firmware the extended rates
in the association request's rates TLV.  Found this on a Linksys
WRT54G v2; it denies association with status code 18 unless you
add the extended rates too.  The old driver did this, but it got
lost in the cfg80211 conversion.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05 16:05:26 -04:00
Dan Williams
aebb628f39 libertas: get the right # of scanned BSSes
Let's actually check the right field in the command response; and
if there aren't any reported BSSes, exit early with success.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-05 16:03:40 -04:00
John W. Linville
c0068c8589 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-next-2.6 2010-08-05 15:54:28 -04:00
Rusty Russell
a767bde4d4 virtio_net: implements ethtool_ops.get_drvinfo
I often use "ethtool -i" command to check what driver controls the
ehternet device.  But because current virtio_net driver doesn't
support "ethtool -i", it becomes the following:

        # ethtool -i eth3
        Cannot get driver information: Operation not supported

This patch simply adds the "ethtool -i" support. The following is the
result when using the virtio_net driver with my patch applied to.

        # ethtool -i eth3
        driver: virtio_net
        version: N/A
        firmware-version: N/A
        bus-info: virtio0

Personally, "-i" is one of the most frequently-used option, and most
network drivers support "ethtool -i", so I think virtio_net also
should do.

Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE)
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 21:53:17 -07:00
stephen hemminger
d7100da026 ppp: make channel_ops const
The PPP channel ops structure should be const.
Cleanup the declarations to use standard C99 format.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 21:53:17 -07:00
David Howells
3b5bac2bde RxRPC: Fix a potential deadlock between the call resend_timer and state_lock
RxRPC can potentially deadlock as rxrpc_resend_time_expired() wants to get
call->state_lock so that it can alter the state of an RxRPC call.  However, its
caller (call_timer_fn()) has an apparent lock on the timer struct.

The problem is that rxrpc_resend_time_expired() isn't permitted to lock
call->state_lock as this could cause a deadlock against rxrpc_send_abort() as
that takes state_lock and then attempts to delete the resend timer by calling
del_timer_sync().

The deadlock can occur because del_timer_sync() will sit there forever waiting
for rxrpc_resend_time_expired() to return, but the latter may then wait for
call->state_lock, which rxrpc_send_abort() holds around del_timer_sync()...

This leads to a warning appearing in the kernel log that looks something like
the attached.

It should be sufficient to simply dispense with the locks.  It doesn't matter
if we set the resend timer expired event bit and queue the event processor
whilst we're changing state to one where the resend timer is irrelevant as the
event can just be ignored by the processor thereafter.

=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.35-rc3-cachefs+ #115
-------------------------------------------------------
swapper/0 is trying to acquire lock:
 (&call->state_lock){++--..}, at: [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]

but task is already holding lock:
 (&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&call->resend_timer){+.-...}:
       [<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
       [<ffffffff81056184>] lock_acquire+0x57/0x6d
       [<ffffffff8103bb9c>] del_timer_sync+0x3c/0x86
       [<ffffffffa002bb7a>] rxrpc_send_abort+0x50/0x97 [af_rxrpc]
       [<ffffffffa002bdd9>] rxrpc_kernel_abort_call+0xa1/0xdd [af_rxrpc]
       [<ffffffffa0061588>] afs_deliver_to_call+0x129/0x368 [kafs]
       [<ffffffffa006181b>] afs_process_async_call+0x54/0xff [kafs]
       [<ffffffff8104261d>] worker_thread+0x1ef/0x2e2
       [<ffffffff81045f47>] kthread+0x7a/0x82
       [<ffffffff81002cd4>] kernel_thread_helper+0x4/0x10

-> #0 (&call->state_lock){++--..}:
       [<ffffffff81055237>] validate_chain+0x727/0xd23
       [<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
       [<ffffffff81056184>] lock_acquire+0x57/0x6d
       [<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
       [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
       [<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
       [<ffffffff81036828>] __do_softirq+0xa2/0x13e
       [<ffffffff81002dcc>] call_softirq+0x1c/0x28
       [<ffffffff810049f0>] do_softirq+0x38/0x80
       [<ffffffff810361a2>] irq_exit+0x45/0x47
       [<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
       [<ffffffff81002893>] apic_timer_interrupt+0x13/0x20
       [<ffffffff810011ac>] cpu_idle+0x4d/0x83
       [<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1

other info that might help us debug this:

1 lock held by swapper/0:
 #0:  (&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5

stack backtrace:
Pid: 0, comm: swapper Not tainted 2.6.35-rc3-cachefs+ #115
Call Trace:
 <IRQ>  [<ffffffff81054414>] print_circular_bug+0xae/0xbd
 [<ffffffff81055237>] validate_chain+0x727/0xd23
 [<ffffffff810560bc>] __lock_acquire+0x889/0x8fa
 [<ffffffff810539a7>] ? mark_lock+0x42f/0x51f
 [<ffffffff81056184>] lock_acquire+0x57/0x6d
 [<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
 [<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43
 [<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
 [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc]
 [<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5
 [<ffffffff8103b675>] ? run_timer_softirq+0x182/0x2a5
 [<ffffffffa002007e>] ? rxrpc_resend_time_expired+0x0/0x96 [af_rxrpc]
 [<ffffffff810367ef>] ? __do_softirq+0x69/0x13e
 [<ffffffff81036828>] __do_softirq+0xa2/0x13e
 [<ffffffff81002dcc>] call_softirq+0x1c/0x28
 [<ffffffff810049f0>] do_softirq+0x38/0x80
 [<ffffffff810361a2>] irq_exit+0x45/0x47
 [<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96
 [<ffffffff81002893>] apic_timer_interrupt+0x13/0x20
 <EOI>  [<ffffffff81049de1>] ? __atomic_notifier_call_chain+0x0/0x86
 [<ffffffff8100955b>] ? mwait_idle+0x6e/0x78
 [<ffffffff81009552>] ? mwait_idle+0x65/0x78
 [<ffffffff810011ac>] cpu_idle+0x4d/0x83
 [<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 21:53:16 -07:00
Changli Gao
f2f009812f sch_sfq: add sanity check for the packet length
The packet length should be checked before the packet data is dereferenced.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 21:53:16 -07:00
Changli Gao
12dc96d167 cls_rsvp: add sanity check for the packet length
The packet length should be checked before the packet data is dereferenced.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 21:53:15 -07:00
Changli Gao
4b95c3d40d cls_flow: add sanity check for the packet length
The packet length should be checked before the packet data is dereferenced.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 21:53:15 -07:00
Changli Gao
f9599ce111 sk_buff: introduce pskb_network_may_pull()
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 21:53:14 -07:00
Changli Gao
36d12690a2 act_nat: fix on the TX path
On the TX path, skb->data points to the ethernet header, not the network
header. So when validating the packet length for accessing we should
take the ethernet header into account.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 21:53:14 -07:00
Joe Perches
c33788b45f drivers/net/enic: Use %pUB to format a UUID
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 16:18:04 -07:00
Stefan Weil
2a1bc0d56b davinci_emac: Fix use after free in davinci_emac_remove
free_netdev finally calls kfree which makes the contents
of ndev and priv (private data contained in ndev) invalid.

So iounmap should be called before free_netdev.

Cc: David S. Miller <davem@davemloft.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sriramakrishnan <srk@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 16:18:03 -07:00
Kulikov Vasiliy
889635fd6b via-velocity: do not use PCI resources before pci_enable_device()
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.

The semantic match that finds this problem is as follows:

// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@

(
* x->irq
|
* x->resource
|
* request(x, ...)
)
 ...
*pci_enable_device(x)
// </smpl>

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 16:18:03 -07:00
Kulikov Vasiliy
7a0c2029d6 cxgb4vf: do not use PCI resources before pci_enable_device()
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.

The semantic match that finds this problem is as follows:

// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@

(
* x->irq
|
* x->resource
|
* request(x, ...)
)
 ...
*pci_enable_device(x)
// </smpl>

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 16:18:02 -07:00
Kulikov Vasiliy
7aaaaa1e44 cxgb3: do not use PCI resources before pci_enable_device()
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.

The semantic match that finds this problem is as follows:

// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@

(
* x->irq
|
* x->resource
|
* request(x, ...)
)
 ...
*pci_enable_device(x)
// </smpl>

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04 16:18:02 -07:00
Linus Torvalds
3cfc2c42c1 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (48 commits)
  Documentation: update broken web addresses.
  fix comment typo "choosed" -> "chosen"
  hostap:hostap_hw.c Fix typo in comment
  Fix spelling contorller -> controller in comments
  Kconfig.debug: FAIL_IO_TIMEOUT: typo Faul -> Fault
  fs/Kconfig: Fix typo Userpace -> Userspace
  Removing dead MACH_U300_BS26
  drivers/infiniband: Remove unnecessary casts of private_data
  fs/ocfs2: Remove unnecessary casts of private_data
  libfc: use ARRAY_SIZE
  scsi: bfa: use ARRAY_SIZE
  drm: i915: use ARRAY_SIZE
  drm: drm_edid: use ARRAY_SIZE
  synclink: use ARRAY_SIZE
  block: cciss: use ARRAY_SIZE
  comment typo fixes: charater => character
  fix comment typos concerning "challenge"
  arm: plat-spear: fix typo in kerneldoc
  reiserfs: typo comment fix
  update email address
  ...
2010-08-04 15:31:02 -07:00
Linus Torvalds
5cf65713f8 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits)
  Revert "HID: add support for the Wacom Intuos 4 wireless"
  HID: fix up Kconfig entry for ACRUX driver
  HID: add ACRUX game controller force feedback support
  HID: Force input registration for "VEC footpedal"
  HID: add HID_QUIRK_HIDINPUT_FORCE
  HID: hid-input.c: indentation fixes
  HID: hiddev: use usb_find_interface, get rid of BKL
  HID: ignore digitizer usage Undefined (0x00)
  HID: Add support for Conceptronic CLLRCMCE
  HID: hid-ids.h: Whitespace fixup, align using TABs
  HID: picolcd: implement refcounting of framebuffer
  HID: picolcd: do not reallocate memory on depth change
  HID: picolcd: Add minimal palette required by fbcon on 8bpp
  HID: magicmouse: Correct parsing of large X and Y motions.
  HID: magicmouse: report last touch up
  HID: picolcd: fix deferred_io init/cleanup to fb ordering
  HID: hid-ids.h: keep vendor ids in alphabetical order
  HID: add proper support for Elecom BM084 bluetooth mouse
  HID: magicmouse: enable horizontal scrolling
  HID: magicmouse: add param for scroll speed
  ...
2010-08-04 15:23:49 -07:00
Linus Torvalds
b7c8e55db7 Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (39 commits)
  random: Reorder struct entropy_store to remove padding on 64bits
  padata: update API documentation
  padata: Remove padata_get_cpumask
  crypto: pcrypt - Update pcrypt cpumask according to the padata cpumask notifier
  crypto: pcrypt - Rename pcrypt_instance
  padata: Pass the padata cpumasks to the cpumask_change_notifier chain
  padata: Rearrange set_cpumask functions
  padata: Rename padata_alloc functions
  crypto: pcrypt - Dont calulate a callback cpu on empty callback cpumask
  padata: Check for valid cpumasks
  padata: Allocate cpumask dependend recources in any case
  padata: Fix cpu index counting
  crypto: geode_aes - Convert pci_table entries to PCI_VDEVICE (if PCI_ANY_ID is used)
  pcrypt: Added sysfs interface to pcrypt
  padata: Added sysfs primitives to padata subsystem
  padata: Make two separate cpumasks
  padata: update documentation
  padata: simplify serialization mechanism
  padata: make padata_do_parallel to return zero on success
  padata: Handle empty padata cpumasks
  ...
2010-08-04 15:23:14 -07:00
Linus Torvalds
ffd386a9a8 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: allow limited allocation before slab is online
  percpu: make @dyn_size always mean min dyn_size in first chunk init functions
2010-08-04 15:17:52 -07:00
Linus Torvalds
03da309867 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (276 commits)
  [SCSI] zfcp: Trigger logging in the FCP channel on qdio error conditions
  [SCSI] zfcp: Introduce experimental support for DIF/DIX
  [SCSI] zfcp: Enable data division support for FCP devices
  [SCSI] zfcp: Prevent access on uninitialized memory.
  [SCSI] zfcp: Post events through FC transport class
  [SCSI] zfcp: Cleanup QDIO attachment and improve processing.
  [SCSI] zfcp: Cleanup function parameters for sbal value.
  [SCSI] zfcp: Use correct width for timer_interval field
  [SCSI] zfcp: Remove SCSI device when removing unit
  [SCSI] zfcp: Use memdup_user and kstrdup
  [SCSI] zfcp: Fix retry after failed "open port" erp action
  [SCSI] zfcp: Fail erp after timeout
  [SCSI] zfcp: Use forced_reopen in terminate_rport_io callback
  [SCSI] zfcp: Register SCSI devices after successful fc_remote_port_add
  [SCSI] zfcp: Do not try "forced close" when port is already closed
  [SCSI] zfcp: Do not unblock rport from REOPEN_PORT_FORCED
  [SCSI] sd: add support for runtime PM
  [SCSI] implement runtime Power Management
  [SCSI] convert to the new PM framework
  [SCSI] Unify SAM_ and SAM_STAT_ macros
  ...
2010-08-04 15:15:15 -07:00
Andy Lutomirski
2411054ae9 iwlagn: Improve aggregation failure error messages
82ca934176 added scary looking
but harmless error messages.  Make them clearer and make the
actual failure message show up with the same severity as the
harmless one.

Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:30:55 -04:00
Kulikov Vasiliy
47cb905d6b rt2x00: do not use PCI resources before pci_enable_device()
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.

The semantic match that finds this problem is as follows:

// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@

(
* x->irq
|
* x->resource
|
* request(x, ...)
)
 ...
*pci_enable_device(x)
// </smpl>

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:28:37 -04:00
Juuso Oikarinen
93c08c3291 mac80211: Fix compilation warning when CONFIG_INET is not set
The warning is:
  net/mac80211/main.c:688: warning: label ‘fail_ifa’ defined but not used

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:28:37 -04:00
Christoph Fritz
93c0584ca9 wireless: ipw2100: check result of kzalloc()
If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is
called by register_netdev.

CC: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:28:37 -04:00
Jan Friedrich
c8f3b72133 ath9k: fix erased ieee80211_rx_status.mactime
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again -
mactime is always 0. This causes problems in IBSS mode.

ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed.
Without this patch the merge is triggered by each beacon received.

This can be recognized by the "beacon TSF higher than local TSF - IBSS
merge with BSSID" log message accompanying each beacon.

This problem was not completely fixed in commit
a6d2055b02 and is not a stable kernel fix.
It is solely intended for wireless-testing.

Signed-off-by: Jan Friedrich <jft@dev2day.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:28:37 -04:00
Larry Finger
5f7aebd845 p54pci: Add PCI ID for SMC2802W
The SMC2802W appears to work with p54pci.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: David Cozatt <olbrannon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:27:38 -04:00
Lorenzo Bianconi
7540184942 ath9k: fix an issue in ath_atx_tid paused flag management
I noticed a possible issue in the paused flag management of the
ath_atx_tid data structure. In particular, in a noisy environment and
under heavy load, I observed that the AGGR session establishment could
fail several times consecutively causing values of the paused flag
greater than one for this TID (ath_tx_pause_tid is called more than
once from ath_tx_aggr_start).

Considering that the session for this TID can not be established also
after the mac80211 stack calls the ieee80211_agg_tx_operational() since
the ath_tx_aggr_resume() lowers the paused flag only by one.

This patch also replaces some BUG_ON calls with WARN_ON, as even if
these unlikely conditions happen, it's not fatal enough to justify a
BUG_ON.

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:27:38 -04:00
Luis R. Rodriguez
824b185adf ath9k_hw: Fix regulatory CTL index usage for AR9003
AR9003 was not relying on the CTL indexes from the EEPROM for capping the
max output power. The CTL indexes from the EEPROM provide calibrated
limits for output power for each tested and supported frequency. Without
this the device operates at a power level which only conforms to the
transmit spectrum mask as specified by IEEE Annex I.2.3.

The regulatory limit by CRDA is always used but does not provide
calibrated values for optimal performance, specially on band edges.
Using the calibrated data from the EEPROM ensures the device
operates at optimal output power while still ensuring proper
regulatory compliance. The device uses the minimum of these tree
values, the value from CRDA, the calibrated value from CTL indexex,
and the value to conform to the IEEE transmit spectrum mask.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:27:38 -04:00
Kulikov Vasiliy
bb1236115e net: wl12xx: do not use kfree'd memory
wl1271_dump() uses cmd after kfree(cmd). Move kfree() just after
wl1271_dump().

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:27:38 -04:00
Wey-Yi Guy
74dee2c3e1 iwlagn: fix typo in ucode_bt_stats_read debugfs
small typo fix in ucode_bt_stats_read debugfs file

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:27:38 -04:00
Wey-Yi Guy
735df29a06 iwlwifi: BA scd_flow not match condition detected
It is a uCode bug which cause the tx queue id not match scd_flow
in compressed block ack frame, and it need to be addressed in uCode.
Currently, driver will log the information when it happen.

Since it is possible happen very often and we do not want to fill the syslog,
so don't enable the logging by default.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:27:37 -04:00