Don't enable U1 or U2 Link powermanagenet (LPM) states for USB3
devices connected to tier 2 or further hubs.
For unknown reasons we previously only prevented U1.
Be consistent, and prevent both U1/U2 states if tier policy doesn't
allow LPM.
Also check the tier policy a bit earlier, and return if U1/U2 is
not allowed. This avoids unnecessary xhci MEL commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'stop endpoint' command timer was started when a 'stop endpoint'
command was added to the command queue.
This can trigger unwanted timeouts if there are several pending commands
in the queue that xHC needs to handle first.
The generic command timer, which was added later than the 'stop endpoint'
timeout timer, times each command currently being handled by xHC hardware.
A timed out stop endpoint command was treated as a more severe issue than
other failed commands, so the separate stop endpoint timer was left
unchanged.
Use the generic command timer for stop endpoint commands. Identify if
the timed out command was a stop endpoint command in the generic handler,
and treat it with the same severity as earlier.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Activate the just added extension for xhci-plat and omit the shared
hcd if either of the root hubs has no ports.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares xhci-plat for the following scenario
- If either of the root hubs has no ports, then omit shared hcd
- Main hcd can be USB3 if there are no USB2 ports
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is in preparation of an extension where in case of a
root hub with no ports no shared hcd will be created.
Whether one of the root hubs has no ports we figure our in
usb_add_hcd() for the primary hcd. Therefore create the shared hcd
only after this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares xhci for the following scenario:
- If either of the root hubs has no ports, then omit shared hcd
- Main hcd can be USB3 if there are no USB2 ports
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factoring out parts of xhci_gen_setup() has two motivations:
- When adding functionaliy to omit shared hcd if not needed in a
subsequent patch, we'll have to call xhci_hcd_init_usb3_data()
from two places.
- It reduces size of xhci_gen_setup() and makes it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd() if xhci has two roothubs.
This will make sure both primary roothub and secondary roothub will be
registered along with the second HCD.
This is required for cold plugged USB devices to be detected in certain
PCIe USB cards (like Inateck USB card connected to AM64 EVM or J7200 EVM).
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26 ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2 ("usb: hub: Fix usb enumeration issue due to address0
race")
[minor rebase change, and commit message update -Mathias]
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch resolves kernel-doc warnings to add return value description
in function comments.
Addressed warnings:
drivers/usb/host/ehci-xilinx-of.c:37: warning: No description found for return value of 'ehci_xilinx_port_handed_over'
drivers/usb/host/ehci-xilinx-of.c:117: warning: No description found for return value of 'ehci_hcd_xilinx_of_probe'
drivers/usb/host/ehci-xilinx-of.c:201: warning: No description found for return value of 'ehci_hcd_xilinx_of_remove'
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220509170252.28271-1-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch resolves checkpatch warnings for xilinx EHCI driver.
Addressed warnings:
WARNING: quoted string split across lines
50: FILE: drivers/usb/host/ehci-xilinx-of.c:50:
+ "The USB host controller does not support full speed "
+ "nor low speed devices\n");
WARNING: quoted string split across lines
53: FILE: drivers/usb/host/ehci-xilinx-of.c:53:
+ "You can reconfigure the host controller to have "
+ "full speed support\n");
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220510132252.26001-1-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After moving the omap1 platform into generalized multiplatform
support on ARM, the kernel test robot points out a W=1 warning that
now shows up in more configurations:
drivers/usb/host/ehci-omap.c:64:19: warning: unused function 'ehci_read'
The function was last used 9 years ago and can just be removed.
Fixes: 87425ad363 ("USB: ehci-omap: Remove PHY reset handling code")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220428102314.950323-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The third argument of usb_maxpacket(): in_out has been deprecated
because it could be derived from the second argument (e.g. using
usb_pipeout(pipe)).
N.B. function usb_maxpacket() was made variadic to accommodate the
transition from the old prototype with three arguments to the new one
with only two arguments (so that no renaming is needed). The variadic
argument is to be removed once all users of usb_maxpacket() get
migrated.
CC: Duncan Sands <duncan.sands@free.fr>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20220317035514.6378-7-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in oxu_bus_suspend(), which is shown below:
(Thread 1) | (Thread 2)
| timer_action()
oxu_bus_suspend() | mod_timer()
spin_lock_irq() //(1) | (wait a time)
... | oxu_watchdog()
del_timer_sync() | spin_lock_irq() //(2)
(wait timer to stop) | ...
We hold oxu->lock in position (1) of thread 1, and use
del_timer_sync() to wait timer to stop, but timer handler
also need oxu->lock in position (2) of thread 2. As a result,
oxu_bus_suspend() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irq(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417120305.64577-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver, OMAP1 specific, now omits clk_prepare/unprepare() steps, not
supported by OMAP1 custom implementation of clock API. However, non-CCF
stubs of those functions exist for use on such platforms until converted
to CCF.
Update the driver to be compatible with CCF implementation of clock API.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Link: https://lore.kernel.org/r/20220402114353.130775-1-jmkrzyszt@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Zhen Ni <nizhen@uniontech.com>
Link: https://lore.kernel.org/r/20220302033716.31272-1-nizhen@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ)
for requesting IRQ's resources any more, as they can be not ready yet in
case of DT-booting.
platform_get_irq() instead is a recommended way for getting IRQ even if
it was not retrieved earlier.
It also makes code simpler because we're getting "int" value right away
and no conversion from resource to int is required.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220309053611.2081191-1-chi.minghao@zte.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
powerpc's asm/prom.h brings some headers that it doesn't
need itself.
In order to clean it up in a further step, first clean all
files that include asm/prom.h
Some files don't need asm/prom.h at all. For those ones,
just remove inclusion of asm/prom.h
Some files don't need any of the items provided by asm/prom.h,
but need some of the headers included by asm/prom.h. For those
ones, add the needed headers that are brought by asm/prom.h at
the moment, then remove asm/prom.h
Some files really need asm/prom.h but also need some of the
headers included by asm/prom.h. For those one, leave asm/prom.h
but also add the needed headers so that they can be removed
from asm/prom.h in a later step.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/295e87a3094a92784657f7060fb0927e762a2e3c.1650011506.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alderlake has two XHCI controllers with PCI IDs 0x461e and 0x51ed. We
had previously added the quirk to default enable runtime PM for 0x461e,
now add it for 0x51ed as well.
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220408114225.1.Ibcff6b86ed4eacfe4c4bc89c90e18416f3900a3e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In zhaoxin platform, some ehci projects will latch a wakeup signal
internal when plug in a device on port during system S0. This wakeup
signal will turn on when ehci runtime suspend, which will trigger a
system control interrupt that will resume ehci back to D0. As no
device connect, ehci will be set to runtime suspend and turn on the
internal latched wakeup signal again. It will cause a suspend-resume
loop and generate system control interrupt continuously.
Fixed this issue by clear wakeup signal latched in ehci internal when
ehci resume callback is called.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20220324121735.3803-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced.
Fixes: 41a7426d25 ("usb: xhci: tegra: Unlink power domain devices")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220319023822.145641-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The innovator board needs a special case for its phy control.
Move the corresponding code into the board file and out of the
common code by adding another callback.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The omap usb drivers still rely on mach/*.h headers that
are explicitly or implicitly included, but all the required
definitions are now in include/linux/soc/ti/, so use those
instead and allow compile-testing on other architectures.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The register definitions in this header are used in at least four
different places, with little hope of completely cleaning that up.
Split up the file into a portion that becomes a linux-wide header
under include/linux/soc/ti/, and the parts that are actually only
needed by board files.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The mach/hardware.h is included in lots of places, and it provides
three different things on pxa:
- the cpu_is_pxa* macros
- an indirect inclusion of mach/addr-map.h
- the __REG() and io_pv2() helper macros
Split it up into separate <linux/soc/pxa/cpu.h> and mach/pxa-regs.h
headers, then change all the files that use mach/hardware.h to
include the exact set of those three headers that they actually
need, allowing for further more targeted cleanup.
linux/soc/pxa/cpu.h can remain permanently exported and is now in
a global location along with similar headers. pxa-regs.h and
addr-map.h are only used in a very small number of drivers now
and can be moved to arch/arm/mach-pxa/ directly when those drivers
are to pass the necessary data as resources.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-leds@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The first U3 wake signal by the host may be lost if the USB 3 connection is
tunneled over USB4, with a runtime suspended USB4 host, and firmware
implemented connection manager.
Specs state the host must wait 100ms (tU3WakeupRetryDelay) before
resending a U3 wake signal if device doesn't respond, leading to U3 -> U0
link transition times around 270ms in the tunneled case.
Fixes: 0200b9f790 ("xhci: Wait until link state trainsits to U0 after setting USB_SS_PORT_LS_U0")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some situations software handles TRB events slower than adding TRBs.
If the number of TRB events to be processed in a given interrupt is exactly
the same as the event ring size 256, then the local variable
"event_ring_deq" that holds the initial dequeue position is equal to
software_dequeue after handling all 256 interrupts.
It will cause driver to not update ERDP to hardware,
Software dequeue pointer is out of sync with ERDP on interrupt exit.
On the next interrupt, the event ring may full but driver will not
update ERDP as software_dequeue is equal to ERDP.
[ 536.377115] xhci_hcd 0000:00:12.0: ERROR unknown event type 37
[ 566.933173] sd 8:0:0:0: [sdb] tag#27 uas_eh_abort_handler 0 uas-tag 7 inflight: CMD OUT
[ 566.933181] sd 8:0:0:0: [sdb] tag#27 CDB: Write(10) 2a 00 17 71 e6 78 00 00 08 00
[ 572.041186] xhci_hcd On some situataions,the0000:00:12.0: xHCI host not responding to stop endpoint command.
[ 572.057193] xhci_hcd 0000:00:12.0: Host halt failed, -110
[ 572.057196] xhci_hcd 0000:00:12.0: xHCI host controller not responding, assume dead
[ 572.057236] sd 8:0:0:0: [sdb] tag#26 uas_eh_abort_handler 0 uas-tag 6 inflight: CMD
[ 572.057240] sd 8:0:0:0: [sdb] tag#26 CDB: Write(10) 2a 00 38 eb cc d8 00 00 08 00
[ 572.057244] sd 8:0:0:0: [sdb] tag#25 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD
Hardware ERDP is updated mid event handling if there are more than 128
events in an interrupt (half of ring size).
Fix this by updating the software local variable at the same time as
hardware ERDP.
[commit message rewording -Mathias]
Fixes: dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYkF9UwAKCRCAXGG7T9hj
vsXpAPwKXI4WIQcvnVCdULQfuXpA1TbD5XZuS9OuiN/OxWHbzAEA1VHWTmS+tpZ1
ptOyoGhAWhTGeplToobDSGz5qTXEPAI=
=FaKX
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- A bunch of minor cleanups
- A fix for kexec in Xen dom0 when executed on a high cpu number
- A fix for resuming after suspend of a Xen guest with assigned PCI
devices
- A fix for a crash due to not disabled preemption when resuming as Xen
dom0
* tag 'for-linus-5.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: fix is_xen_pmu()
xen: don't hang when resuming PCI device
arch:x86:xen: Remove unnecessary assignment in xen_apic_read()
xen/grant-table: remove readonly parameter from functions
xen/grant-table: remove gnttab_*transfer*() functions
drivers/xen: use helper macro __ATTR_RW
x86/xen: Fix kerneldoc warning
xen: delay xen_hvm_init_time_ops() if kdump is boot on vcpu>=32
xen: use time_is_before_eq_jiffies() instead of open coding it
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
Here is the big set of USB and Thunderbolt changes for 5.18-rc1.
Nothing major in here, just lots of little improvements and cleanups and
new device support. Highlights are:
- list iterator fixups for when we walk past the end of the list
(a common problem that was cut/pasted in almost all USB gadget
drivers)
- xen USB driver "hardening" for malicious hosts
- xhci driver updates and fixes for more hardware types
- xhci debug cable fixes to make it actually work again
- usb gadget audio driver improvements
- usb gadget storage fixes to work with OS-X
- lots of other small usb gadget fixes and updates
- USB DWC3 driver improvements for more hardware types
- Lots of other small USB driver improvements
- DTS updates for some USB platforms
Note, the DTS updates will have a merge conflict in your tree. The
fixup should be simple, but if not, I can provide a merged tree if
needed.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYj7qpQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRsQCcCryYifAvE2gHaNfI4B01JRWk7gQAoLNiUgvl
l+srEAXgIVueDhmDxy5P
=/Ppv
-----END PGP SIGNATURE-----
Merge tag 'usb-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 5.18-rc1.
Nothing major in here, just lots of little improvements and cleanups
and new device support. Highlights are:
- list iterator fixups for when we walk past the end of the list (a
common problem that was cut/pasted in almost all USB gadget
drivers)
- xen USB driver "hardening" for malicious hosts
- xhci driver updates and fixes for more hardware types
- xhci debug cable fixes to make it actually work again
- usb gadget audio driver improvements
- usb gadget storage fixes to work with OS-X
- lots of other small usb gadget fixes and updates
- USB DWC3 driver improvements for more hardware types
- Lots of other small USB driver improvements
- DTS updates for some USB platforms
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
usb: gadget: fsl_qe_udc: Add missing semicolon in qe_ep_dequeue()
dt-bindings: usb: mtk-xhci: add compatible for mt8186
usb: dwc3: Issue core soft reset before enabling run/stop
usb: gadget: Makefile: remove ccflags-y
USB: usb-storage: Fix use of bitfields for hardware data in ene_ub6250.c
usb: gadget: eliminate anonymous module_init & module_exit
usb: usbip: eliminate anonymous module_init & module_exit
xen/usb: harden xen_hcd against malicious backends
usb: dwc3: gadget: Wait for ep0 xfers to complete during dequeue
usb: dwc3: gadget: move cmd_endtransfer to extra function
usb: dwc3: gadget: ep_queue simplify isoc start condition
xen/usb: don't use arbitrary_virt_to_machine()
usb: isp1760: remove redundant max_packet() macro
usb: oxu210hp-hcd: remove redundant call to max_packet() macro
usb: common: usb-conn-gpio: Make VBUS supply completely optional
USB: storage: ums-realtek: fix error code in rts51x_read_mem()
usb: early: xhci-dbc: Fix xdbc number parsing
usb: early: xhci-dbc: Remove duplicate keep parsing
x86/tsc: Be consistent about use_tsc_delay()
usb: gadget: udc: s3c2410: remove usage of list iterator past the loop body
...
The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus types,
causing updates to most SPI device drivers. The branch with that on has
been cross merged with a couple of other trees which added new SPI
drivers this cycle, I'm not expecting any build issues resulting from
the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmI4b+8ACgkQJNaLcl1U
h9AB+Qf/WhPzDSCdhK1repnSmEpRNs/J6hItmY2H6pTQaWALpfTB0+p1Nb5tAotg
fHbu6a2AsiiwWt+tDal44GFYhS0CDSOT4hqgLV8msyDDPPJqqr7A2dbu7YrCjTVI
TgNZNwxW7c2LgqBXR9GV7NPWYoxYxveoYh+L+05MSuSQxSOvPl6LUZiZPnPufQM6
dCpEh19atrtasFg3rFnslWBd2C3h8hb6YT7vUZs9gxhg3FvSgpYQwzz5SfFgHXK6
Rg07m8fDTSjf2qo1C4pc/d1Ni1xBe7aHKMtjtR3jJ4q8QqiawfCcvvOep/Iaec1+
s3qnDthohWMJoF1W6ERf3HiAgNIfhg==
=4tlR
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
Make sure a malicious backend can't cause any harm other than wrong
I/O data.
Missing are verification of the request id in a response, sanitizing
the reported actual I/O length, and protection against interrupt storms
from the backend.
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220311103509.12908-1-jgross@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIuUskeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGCFkH/2n3mpGXuITp0ZXE
TNrpbdZOof5SgLw+w7THswXuo6m5yRGNKQs9fvIvDD8Vf7/OdQQfPOmF1cIE5+nk
wcz6aHKbdrok8Jql2qjJqWXZ5xbGj6qywg3zZrwOUsCKFP5p+AjBJcmZOsvQHjSp
ASODy1moOlK+nO52TrMaJw74a8xQPmQiNa+T2P+FedEYjlcRH/c7hLJ7GEnL6+cC
/R4bATZq3tiInbTBlkC0hR0iVNgRXwXNyv9PEXrYYYHnekh8G1mgSNf06iejLcsG
aAYsW9NyPxu8zPhhHNx79K9o8BMtxGD4YQpsfdfIEnf9Q3euqAKe2evRWqHHlDms
RuSCtsc=
=M9Nc
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc8' into usb-next
We need the Xen USB fixes as other patches depend on those changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gnttab_end_foreign_access() family of functions is taking a
"readonly" parameter, which isn't used. Remove it from the function
parameters.
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220311103429.12845-3-jgross@suse.com
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
arbitrary_virt_to_machine() is meant to be used in PV guests only.
Replace its usage with virt_to_gfn().
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220311103500.12885-1-jgross@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function usb_endpoint_maxp() (called by usb_maxpacket()) already
does the sanitazation of the USB endpoint max packet size. The call to
max_packet() does the same thing and is thus removed.
However, the macro max_packet() is kept because it is used elsewhere
in the file.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20220306075524.706660-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- New support:
- Mediatek tphy support for MT8186
- Qualcomm usb phy support for sc8180x and sc8280xp
- Qualcomm ufs phy support for sc8180x and sc8280xp
- Qualcomm usb phy support for MSM8953
- Cadence D-Phy Rx support
- Sun4i support for USB phy
- Rockchip naneng combo phy support for RK3568
- Qualcomm eDP PHY for sc7280
- Updates:
- wake on support for Synopsis XHCI controllers
- Yamilify Qualcomm USB HS phy binding
- Charger detection support for TI tusb1210
-----BEGIN PGP SIGNATURE-----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=8baK
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.18
- New support:
- Mediatek tphy support for MT8186
- Qualcomm usb phy support for sc8180x and sc8280xp
- Qualcomm ufs phy support for sc8180x and sc8280xp
- Qualcomm usb phy support for MSM8953
- Cadence D-Phy Rx support
- Sun4i support for USB phy
- Rockchip naneng combo phy support for RK3568
- Qualcomm eDP PHY for sc7280
- Updates:
- wake on support for Synopsis XHCI controllers
- Yamilify Qualcomm USB HS phy binding
- Charger detection support for TI tusb1210
* tag 'phy-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (53 commits)
phy: qcom-qmp: add sc8280xp UFS PHY
dt-bindings: phy: qcom,qmp: add sc8180x and sc8280xp ufs compatibles
phy: qcom-snps: Add sc8280xp support
dt-bindings: phy: qcom,usb-snps-femto-v2: Add sc8180x and sc8280xp
dt-bindings: Revert "dt-bindings: soc: grf: add naneng combo phy register compatible"
phy: dt-bindings: Add Cadence D-PHY Rx bindings
phy: dt-bindings: cdns,dphy: add power-domains property
phy: dt-bindings: Convert Cadence DPHY binding to YAML
phy: cadence: Add Cadence D-PHY Rx driver
dt-bindings: phy: renesas,usb2-phy: Document RZ/V2L phy bindings
Revert "PCI: aardvark: Fix initialization with old Marvell's Arm Trusted Firmware"
Revert "usb: host: xhci: mvebu: make USB 3.0 PHY optional for Armada 3720"
Revert "ata: ahci: mvebu: Make SATA PHY optional for Armada 3720"
phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation
phy: marvell: phy-mvebu-a3700-comphy: Remove port from driver configuration
phy: phy-brcm-usb: fixup BCM4908 support
dt-bindings: phy: mediatek,tphy: Add compatible for MT8192
phy: ti: tusb1210: Add charger detection
phy: ti: tusb1210: Add a delay between power-on and restoring the phy-parameters
phy: ti: tusb1210: Drop tusb->vendor_specific2 != 0 check from tusb1210_power_on()
...
The usage of gnttab_end_foreign_access() in xenhcd_gnttab_done() is
not safe against a malicious backend, as the backend could keep the
I/O page mapped and modify it even after the granted memory page is
being used for completely other purposes in the local system.
So replace that use case with gnttab_try_end_foreign_access() and
disable the PV host adapter in case the backend didn't stop using the
granted page.
In xenhcd_urb_request_done() immediately return in case of setting
the device state to "error" instead of looking into further backend
responses.
Reported-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
---
V2:
- use gnttab_try_end_foreign_access()
The ret/retval will be set when it used, no need to init at definition.
[modified subject line -Mathias]
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store temperary value in hcc_params.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The for loop to find page size bit can be replaced with ffs().
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race between system resume and device-initiated resume may result in
runtime PM imbalance on USB2 root hub. If a device-initiated resume
starts and system resume xhci_bus_resume() directs U0 before hub driver
sees the resuming device in RESUME state, device-initiated resume will
not be finished in xhci_handle_usb2_port_link_resume(). In this case,
usb_hcd_end_port_resume() call is missing.
This changes calls usb_hcd_end_port_resume() if resuming device reaches
U0 to keep runtime PM balance.
Fixes: a231ec41e6 ("xhci: refactor U0 link state handling in get_port_status")
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_decode_ctrl_ctx() returns the untouched buffer as-is if both "drop"
and "add" parameters are zero.
Fix the function to return an empty string in that case.
It was not immediately clear from the possible call chains whether this
issue is currently actually triggerable or not.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 90d6d5731d ("xhci: Add tracing for input control context")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
commit 4843b4b5ec ("xhci: fix even more unsafe memory usage in xhci tracing")
Link: https://lore.kernel.org/r/20220303110903.1662404-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_decode_usbsts() is expected to return a zero-terminated string by
its only caller, xhci_stop_endpoint_command_watchdog(), which directly
logs the return value:
xhci_warn(xhci, "USBSTS:%s\n", xhci_decode_usbsts(str, usbsts));
However, if no recognized bits are set in usbsts, the function will
return without having called any sprintf() and therefore return an
untouched non-zero-terminated caller-provided buffer, causing garbage
to be output to log.
Fix that by always including the raw value in the output.
Note that before commit 4843b4b5ec ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 9c1aa36efd ("xhci: Show host status when watchdog triggers and host is assumed dead.")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac1912 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here, and it resolves a merge conflict in:
drivers/usb/dwc3/dwc3-pci.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3241929b67.
Armada 3720 phy driver (phy-mvebu-a3700-comphy.c) does not return
-EOPNOTSUPP from phy_power_on() callback anymore.
So remove XHCI_SKIP_PHY_INIT flag from xhci_mvebu_a3700_plat_setup() and
then also whole xhci_mvebu_a3700_plat_setup() function which is there just
to handle -EOPNOTSUPP for XHCI_SKIP_PHY_INIT.
xhci plat_setup callback is not used by any other xhci plat driver, so
remove this callback completely.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220203214444.1508-5-kabel@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This has been allocated just a few lines earlier with a
zalloc(). The value is known and "|=" is a waste of memory
cycles.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220217133549.27961-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of qtd_fill(), we assign the 'int count' variable to the 'size_t
length' field of 'struct ehci_qtd' -- which implies a problematic type cast.
Let's make that variable and the function's result *unsigned int* instead...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8c64fdeb-5857-8cb3-cfd8-0c248a14b909@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_endpoint_{disable|reset}() the expression '&vdev->eps[ep_index]'
just cannot be NULL, so the checks have no sense at all...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every lpm commmand, both for USB 2 and USB 3 devies used the same
xhci->lpm_command structure to change max exit latency.
xhci->lpm_command is only protected by a hcd->bandwidth mutex, which is
not enoungh as USB 2 and USB 3 devices are behind separate HCDs.
Simplify code and avoid unnecessary locking risks by allocating
separate command structures for each lpm command, just like with
all other commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support systems with several xhci controllers with active
dbc on each xhci we need to use IDR to identify and give
an index to each port.
Avoid using global struct tty_driver.driver_state for storing
dbc port pointer as it won't work with several dbc ports
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current workaround to call the dbc_tty_init() in probe is
not working in case we have several xhci devices with dbc enabled.
dbc_tty_init() should be called only once by a module init call when
module is loaded.
until dbgtty is its own module call dbc_tty_init() from xhci
module init call.
Same is true for unloading and dbc_tty_exit()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These names give the impression the functions are related to
module init calls, but are in fact creating and removing the dbc
fake device
Rename them to xhci_create_dbc_dev() and xhci_remove_dbc_dev().
We will need the _init and _exit names for actual dbc module init
and exit calls.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn the dbgtty closer to a device driver by allocating the dbc
structure in its own xhci_dbc_tty_probe() function, and freeing it
in xhci_dbc_tty_remove()
Remove xhci_do_dbc_exit() as its no longer needed.
allocate and create the dbc strcuture in xhci_dbc_tty_probe()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor xhci_dbc_init(), splitting it into logical
parts closer to the Linux device model.
- Create the fake dbc device, depends on xhci strucure
- Allocate a dbc structure, xhci agnostic
- Call xhci_dbc_tty_probe(), similar to actual probe.
Adjustments to xhci_dbc_exit and xhci_dbc_remove are also needed
as a result to the xhci_dbc_init() changes
Mostly non-functional changes, except for creating the dbc sysfs
entry earlier, together with the dbc structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the custom functions xhci_mtk_ldos_{enable,disable}() by
switching to using regulator_bulk to perform the very same thing,
as the regulators are always either both enabled or both disabled.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220214111905.77903-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
[commit message and header edit -Mathias]
Fixes: 203a86613f ("xhci: Avoid NULL pointer deref when host dies.")
Cc: stable@vger.kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.
Cc: stable@vger.kernel.org
Signed-off-by: Puma Hsu <pumahsu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original workaround was added prior to commit e4788edc73 ("USB:
EHCI: Add alias for Broadcom INSNREG"). Now that brcm_insnreg exists in
struct ehci_regs we can use that instead of having a local definition.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20220215000813.1779032-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'ret' local variables are often initialized to 0 but this value is
unused, thus we can kill those initializers...
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/901b7478-45b6-d8b3-f5c6-555712485232@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support ip-sleep wakeup for mt8195, it's a specific revision for
each USB controller, and not following IPM rule.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220128062902.26273-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmH2lIMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWzkH/jmR4RpGgrV5SUHF
8R6tsIjae1WItJ8NoaDgImWRxLKXFU7MM77HoFykuZx5Y5yz5Xf5zuJNXRPrHQbC
lE/8wqWut89LX0+k/pKSzt8BQbyZzImfm5rOSBpMC9VkvMcbuQ8NSJ/YbJOD4iAp
jfRRIkJtLQWL6YRc/xPlHCfVY5Qx+TkNZuFFckPtM2HKIEXS225VCESX9JcABDcQ
j7zG5bq/H+8qGItD2iUg8Nw9hqrLutdKSOgP29wxVOajY5QWVczYr1J0nfyRSPMb
/Xs1Oo1/+zO+dfCmR45puJZYua+e/iFTJv2RPFLRIE2AV1vMq4WNIgTJlq8DwfQK
C7Jq080=
=6u+c
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc2' into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/usb/host/xhci-mtk-sch.c:265:20: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/160
Link: https://github.com/KSPP/linux/issues/174
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20220120015546.GA75917@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/usb/host/fotg210-hcd.c:4017:20: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20220120222043.GA33559@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worse scenario, could lead to heap overflows.
Also, address the following sparse warning:
drivers/usb/host/ehci-sched.c:1168:40: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/160
Link: https://github.com/KSPP/linux/issues/174
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20220111075427.GA76390@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.
BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk
Original patch went to stable so this should go there as well.
Fixes: ea0f69d821 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller")
Cc: stable@vger.kernel.org
cc: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1aebf115af as the
prerequsite commit for it is not in the tree.
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmG/rsoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGLW8H/0sfRUxZNJ+DgO6W
0LpyIx1DF7S2x1wOQGl7VZsjdy+dtuOW4BtEoqhuQWgQ2sr0zbavbeyZYTXD1+d6
I1h5C6JMD138JkoqZNdeyWwsalAFtVItH+lzszUGKTxueTbKCJTkGMerBZVu/gVY
U3QYZHEkUH6o/2fINYfSMhEgyJpjVEUoaztB2drsC0tNUGeDjTmrhlRrWIKZ6Kn+
oAiMqsomSBF09TZ++GEqMYDTm39CwNDPJzKGyyOx86ydcg4ErWvjp1jfAUX0cvFG
dso2K5mDzTewdF8bW0A1KvsQaliMFpxgZ5CTblYQ6HvyltjRj+0B8207VzHQXBKV
YFZ8y9A=
=mfug
-----END PGP SIGNATURE-----
Merge 5.16-rc6 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO for some strange reason. Switch to propagating the error codes
upstream.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20211214204247.7172-5-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -ENODEV. Switch to propagating the error codes upstream. IRQ0 is no
longer returned by platform_get_irq(), so we now can safely ignore it...
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20211214204247.7172-4-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing platform device resources directly has long been deprecated for
DT as IRQ resources may not be available at device creation time. Drivers
continuing to use static IRQ resources is blocking removing the static setup
from the DT core code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215225203.1991003-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing platform device resources directly has long been deprecated for
DT as IRQ resources may not be available at device creation time. Drivers
relying on the static IRQ resources is blocking removing the static setup
from the DT core code.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215225358.1993774-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory resource is already retrieved with platform_get_resource(), so
let's use it instead of assuming it is the first resource in the array.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215225509.1995417-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing unlock before return from function xenhcd_urb_request_done()
and xenhcd_conn_notify() in the error handling case.
Fixes: 494ed3997d ("usb: Introduce Xen pvUSB frontend (xen hcd)")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211215035805.375244-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD's Yellow Carp platform has few more XHCI controllers,
enable the runtime power management support for the same.
Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211215093216.1839065-1-Nehal-Bakulchandra.shah@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is warning of 'list_del corruption' when enable list debug
(CONFIG_DEBUG_LIST=y), fix it by using list_del_init()
Fixes: 4ce186665e ("usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211209025422.17108-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduces the Xen pvUSB frontend. With pvUSB it is possible for a Xen
domU to communicate with a USB device assigned to that domU. The
communication is all done via the pvUSB backend in a driver domain
(usually Dom0) which is owner of the physical device.
The pvUSB frontend is a USB hcd for a virtual USB host connector.
The code is taken from the pvUSB implementation in Xen done by Fujitsu
based on Linux kernel 2.6.18.
Changes from the original version are:
- port to upstream kernel
- put all code in just one source file
- move module to appropriate location in kernel tree
- adapt to Linux style guide
- minor code modifications to increase readability
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211123132048.5335-3-jgross@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d356 ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms, e.g. 8183/8192, use low level latch way to keep
wakeup signal, it may latch a wrong signal if debounce more time,
and enable wakeup function earlier.
____________________
ip_sleep ____/ \_____________
___________________
wakeup_signal ____________/ \______
_______________________________
wakeup_en _______/
^ ^
|(1) |(2)
latch wakeup_signal mistakenly at (1), should latch it at (2);
Workaround: delay about 100us to enable wakeup, meanwhile decrease
debounce time.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20211102025004.29156-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Peter Chen <peter.chen@kernel.or> # for chipidea part
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/563123a8117d6cafae3f134e497587bd2b8bb7f4.1636734453.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to (wIndex & 0xff) - 1 can get an integer greater than 15, this
can cause array index to be out of bounds since the size of array
port_status is 15. This change prevents a possible out-of-bounds
pointer computation by forcing the use of a valid port number.
Reported-by: TCS Robot <tcs_robot@tencent.com>
Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20211113165320.GA59686@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small reverts and fixes for USB drivers for issues that
came up during the 5.16-rc1 merge window.
These include:
- two reverts of xhci and USB core patches that are causing
problems in many systems.
- xhci 3.1 enumeration delay fix for systems that were having
problems.
All 3 of these have been in linux-next all week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYziZw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXCACgpgGRQ3yKJJtWczKQy8sFrVmcuIQAn3HXWFnr
VIyCINPkC52d/k1Zj56F
=JGlS
-----END PGP SIGNATURE-----
Merge tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small reverts and fixes for USB drivers for issues that
came up during the 5.16-rc1 merge window.
These include:
- two reverts of xhci and USB core patches that are causing problems
in many systems.
- xhci 3.1 enumeration delay fix for systems that were having
problems.
All three of these have been in linux-next all week with no reported
issues"
* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Fix USB 3.1 enumeration issues by increasing roothub power-on-good delay
Revert "usb: core: hcd: Add support for deferring roothub registration"
Revert "xhci: Set HCD flag to defer primary roothub registration"
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
Some USB 3.1 enumeration issues were reported after the hub driver removed
the minimum 100ms limit for the power-on-good delay.
Since commit 90d28fb53d ("usb: core: reduce power-on-good delay time of
root hub") the hub driver sets the power-on-delay based on the
bPwrOn2PwrGood value in the hub descriptor.
xhci driver has a 20ms bPwrOn2PwrGood value for both roothubs based
on xhci spec section 5.4.8, but it's clearly not enough for the
USB 3.1 devices, causing enumeration issues.
Tests indicate full 100ms delay is needed.
Reported-by: Walt Jr. Brake <mr.yming81@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 90d28fb53d ("usb: core: reduce power-on-good delay time of root hub")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211105160036.549516-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt driver updates for 5.16-rc1.
Nothing major in here, just lots of little cleanups and additions for
new hardware, all of which have been in linux-next for a while with no
reported problems.
Included in here are:
- tiny Thunderbolt driver updates
- USB typec driver updates
- USB serial driver updates
- USB gadget driver updates
- dwc2 and dwc3 controller driver updates
- tiny USB host driver updates
- minor USB driver fixes and updates
- USB dts updates for various platforms
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPaPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylH3wCghhRCsLl5axOKdbkJO2ZUApR71DwAn2Vjwo2Y
Jgo6v3bVWWhL43YwCkf6
=UNgI
-----END PGP SIGNATURE-----
Merge tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
5.16-rc1.
Nothing major in here, just lots of little cleanups and additions for
new hardware, all of which have been in linux-next for a while with no
reported problems.
Included in here are:
- tiny Thunderbolt driver updates
- USB typec driver updates
- USB serial driver updates
- USB gadget driver updates
- dwc2 and dwc3 controller driver updates
- tiny USB host driver updates
- minor USB driver fixes and updates
- USB dts updates for various platforms"
* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (123 commits)
usb: gadget: Mark USB_FSL_QE broken on 64-bit
usb: gadget: f_mass_storage: Disable eps during disconnect
usb: gadget: udc: core: Revise comments for USB ep enable/disable
USB: serial: keyspan: fix memleak on probe errors
USB: serial: cp210x: use usb_control_msg_recv() and usb_control_msg_send()
USB: serial: ch314: use usb_control_msg_recv()
USB: iowarrior: fix control-message timeouts
Documentation: USB: fix example bulk-message timeout
usb: dwc2: stm32mp15: set otg_rev
usb: dwc2: add otg_rev and otg_caps information for gadget driver
dt-bindings: usb: dwc2: adopt otg properties defined in usb-drd.yaml
dt-bindings: usb: dwc2: Add reference to usb-drd.yaml
usb: gadget: uvc: implement dwPresentationTime and scrSourceClock
usb: gadget: uvc: use on returned header len in video_encode_isoc_sg
usb:gadget: f_uac1: fixed sync playback
Docs: usb: remove :c:func: for usb_register and usb_deregister
Docs: usb: update struct usb_driver
usb: gadget: configfs: change config attributes file operation
usb: gadget: configfs: add cfg_to_gadget_info() helper
usb: dwc3: Align DWC3_EP_* flag macros
...
Merge updates related to system sleep for 5.16-rc1:
- Clean up hib_wait_io() (Falla Coulibaly).
- Fix sparse warnings in hibernation-related code (Anders Roxell).
- Use vzalloc() and kzalloc() instead of their open-coded
equivalents in hibernation-related code (Cai Huoqing).
- Prevent user space from crashing the kernel by attempting to
restore the system state from a swap partition in use (Ye Bin).
- Do not let "syscore" devices runtime-suspend during system PM
transitions (Rafael Wysocki).
- Do not pause cpuidle in the suspend-to-idle path (Rafael Wysocki).
- Pause cpuidle later and resume it earlier during system PM
transitions (Rafael Wysocki).
- Make system suspend code use valid_state() consistently (Rafael
Wysocki).
- Add support for enabling wakeup IRQs after invoking the
->runtime_suspend() callback and make two drivers use it (Chunfeng
Yun).
* pm-sleep:
usb: mtu3: enable wake-up interrupt after runtime_suspend called
usb: xhci-mtk: enable wake-up interrupt after runtime_suspend called
PM / wakeirq: support enabling wake-up irq after runtime_suspend called
PM: suspend: Use valid_state() consistently
PM: sleep: Pause cpuidle later and resume it earlier during system transitions
PM: suspend: Do not pause cpuidle in the suspend-to-idle path
PM: sleep: Do not let "syscore" devices runtime-suspend during system transitions
PM: hibernate: Get block device exclusively in swsusp_check()
PM: hibernate: swap: Use vzalloc() and kzalloc()
PM: hibernate: fix sparse warnings
Revert "PM: sleep: Do not assume that "mem" is always present"
PM: hibernate: Remove blk_status_to_errno in hib_wait_io
PM: sleep: Do not assume that "mem" is always present
Use new function dev_pm_set_dedicated_wake_irq_reverse() to request
dedicated wake-up interrupt, due to we want to enable the wake IRQ
after running ->runtime_suspend().
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of maintaining a single-linked list of devices that must be
searched linearly in .remove() just use spi_set_drvdata() to remember the
link between the spi device and the driver struct. Then the global list
and the next member can be dropped.
This simplifies the driver, reduces the memory footprint and the time to
search the list. Also it makes obvious that there is always a corresponding
driver struct for a given device in .remove(), so the error path for
!max3421_hcd can be dropped, too.
As a side effect this fixes a data inconsistency when .probe() races with
itself for a second max3421 device in manipulating max3421_hcd_list. A
similar race is fixed in .remove(), too.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211018204028.2914597-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While going into S3 or S4 suspend, an OHCI host controller can
generate interrupt requests if the INTR_SF enable flag is set. The
interrupt handler routine isn't prepared for this and it doesn't turn
off the flag, causing an interrupt storm.
To fix this problem, make ohci_rh_suspend() always disable INTR_SF
interrupts after processing the done list and the ED unlinks but
before the controller goes into the suspended (non-UsbOperational)
state. There's no reason to leave the flag enabled, since a
suspended controller doesn't generate Start-of-Frame packets.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/1634095928-29639-1-git-send-email-zhuyinbo@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Struct pci_driver contains a struct device_driver, so for PCI devices, it's
easy to convert a device_driver * to a pci_driver * with to_pci_driver().
The device_driver * is in struct device, so we don't need to also keep
track of the pci_driver * in struct pci_dev.
Replace pdev->driver with to_pci_driver(). This is a step toward removing
pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
AMD's Yellow Carp platform supports runtime power management for
XHCI Controllers, so enable the same by default for all XHCI Controllers.
[ regrouped and aligned the PCI_DEVICE_ID definitions -Mathias]
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211014121200.75433-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211011134920.118477-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested on SD5200T TB3 dock which has Fresco Logic FL1100 USB 3.0 Host
Controller.
Before this patch streaming video from USB cam made mouse and keyboard
connected to the same USB bus unusable. Also video was jerky.
With this patch streaming video doesn't have any effect on other
periferals and video is smooth.
Cc: stable@vger.kernel.org
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located.
Cc: stable@vger.kernel.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to allocate resources before registering the tty device to
avoid having a racing open() and write() fail to enable rx or
dereference a NULL pointer when accessing the uninitialised fifo.
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Cc: stable@vger.kernel.org # 4.16
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
[ bjorn: rebased to v5.14-rc2 ]
Link: https://github.com/raspberrypi/linux/issues/3060
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small USB fixes for 5.15-rc5 that resolve a number of
reported issues:
- gadget driver fixes
- xhci build warning fixes
- build configuration fix
- cdc-acm tty handling fixes
- cdc-wdm fix
- typec fixes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYWBsEw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn5KwCfYnVRiMWOqOfbOc3pROB9fV6BrocAoIKyzVoR
BkEqytEaB/DW/5vPzns6
=W9cz
-----END PGP SIGNATURE-----
Merge tag 'usb-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.15-rc5 that resolve a number of
reported issues:
- gadget driver fixes
- xhci build warning fixes
- build configuration fix
- cdc-acm tty handling fixes
- cdc-wdm fix
- typec fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-acm: fix break reporting
USB: cdc-acm: fix racy tty buffer accesses
usb: gadget: f_uac2: fixed EP-IN wMaxPacketSize
usb: cdc-wdm: Fix check for WWAN
usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle
usb: typec: tcpm: handle SRC_STARTUP state if cc changes
usb: typec: tcpci: don't handle vSafe0V event if it's not enabled
usb: typec: tipd: Remove dependency on "connector" child fwnode
Partially revert "usb: Kconfig: using select for USB_COMMON dependency"
usb: dwc3: gadget: Revert "set gadgets parent to the right controller"
usb: xhci: tegra: mark PM functions as __maybe_unused
This is a larger than normal update for Arm SoC specific code, most
of it in device trees, but also drivers and the omap and at91/sama7
platforms:
- There are four new entries to the MAINTAINERS file: Sven Peter and
Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
and Vignesh Raghavendra for TI K3
- Build fixes to address randconfig warnings in sharpsl, dove, omap1,
and qcom platforms as well as the scmi and op-tee subsystems
- Regression fixes for missing CONFIG_FB and other options for several
defconfigs
- Several bug fixes for the newly added Microchip SAMA7 platform,
mostly regarding power management
- Missing SMP barriers to protect accesses to SCMI virtio device
- Regression fixes for TI OMAP, including a boot-time hang on am335x.
- Lots of bug fixes for NXP i.MX, mostly addressing incorrect settings
in devicetree files, and one revert for broken suspend.
- Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
of schema warnings.
- Regression fixes for qualcomm SoC specific drivers and devicetree
files, reverting an mdt_loader change and at least pastially
reverting some of the 5.15 DTS changes, plus some minor bugfixes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Mrh2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a larger than normal update for Arm SoC specific code, most of
it in device trees, but also drivers and the omap and at91/sama7
platforms:
- There are four new entries to the MAINTAINERS file: Sven Peter and
Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
and Vignesh Raghavendra for TI K3
- Build fixes to address randconfig warnings in sharpsl, dove, omap1,
and qcom platforms as well as the scmi and op-tee subsystems
- Regression fixes for missing CONFIG_FB and other options for
several defconfigs
- Several bug fixes for the newly added Microchip SAMA7 platform,
mostly regarding power management
- Missing SMP barriers to protect accesses to SCMI virtio device
- Regression fixes for TI OMAP, including a boot-time hang on am335x.
- Lots of bug fixes for NXP i.MX, mostly addressing incorrect
settings in devicetree files, and one revert for broken suspend.
- Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
of schema warnings.
- Regression fixes for qualcomm SoC specific drivers and devicetree
files, reverting an mdt_loader change and at least pastially
reverting some of the 5.15 DTS changes, plus some minor bugfixes"
* tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits)
MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
firmware: arm_scmi: Add proper barriers to scmi virtio device
firmware: arm_scmi: Simplify spinlocks in virtio transport
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
ARM: sharpsl_param: work around -Wstringop-overread warning
ARM: defconfig: gemini: Restore framebuffer
ARM: dove: mark 'putc' as inline
ARM: omap1: move omap15xx local bus handling to usb.c
MAINTAINERS: Add Vignesh to TI K3 platform maintainership
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
ARM: at91: pm: preload base address of controllers in tlb
ARM: at91: pm: group constants and addresses loading
ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
...
Commit 38225f2ef2 ("ARM/omap1: switch to use dma_direct_set_offset for
lbus DMA offsets") removed a lot of mach/memory.h, but left the USB
offset handling split into arch/arm/mach-omap1/usb.c and
drivers/usb/host/ohci-omap.c.
This can cause a randconfig build warning that now fails the build
with -Werror:
arch/arm/mach-omap1/usb.c:561:30: error: 'omap_1510_usb_ohci_nb' defined but not used [-Werror=unused-variable]
561 | static struct notifier_block omap_1510_usb_ohci_nb = {
| ^~~~~~~~~~~~~~~~~~~~~
Move it all into the platform file to get rid of the final
location that relies on mach/memory.h.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210927144118.2464881-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The added #ifdefs in the PM rework were almost correct, but still
cause warnings in some randconfig builds:
drivers/usb/host/xhci-tegra.c:2147:12: error: 'tegra_xusb_resume' defined but not used [-Werror=unused-function]
2147 | static int tegra_xusb_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-tegra.c:2105:12: error: 'tegra_xusb_suspend' defined but not used [-Werror=unused-function]
2105 | static int tegra_xusb_suspend(struct device *dev)
Replace the #ifdef checks with simpler __maybe_unused annotations to
reliably shut up these warnings.
Link: https://lore.kernel.org/all/20210421135613.3560777-2-arnd@kernel.org/
Fixes: 971ee24706 ("usb: xhci: tegra: Enable ELPG for runtime/system PM")
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211005112057.2700888-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that Kees Cook has added a definition for HCS_N_PORTS_MAX in
commit 72dd184323 ("USB: EHCI: Add register array bounds to HCS
ports"), the code in ehci_hub_control() which sanitizes port index
values can be improved a little.
The idea behind this change is that it prevents a possible
out-of-bounds pointer computation, which the compiler might be able to
detect since the port_status[] array now has a fixed length rather
than a variable length.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20211002190217.GA537967@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dma_map_single() instead of pci_map_single(),
because only dma_map_single() is called here.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210925124920.1564-3-caihuoqing@baidu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dma_map_single() instead of pci_map_single(),
because only dma_map_single() is called here.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210925124920.1564-2-caihuoqing@baidu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dma_map_single() instead of pci_map_single(),
because only dma_map_single() is called here.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210925124920.1564-1-caihuoqing@baidu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd(). This will make sure both
primary roothub and secondary roothub will be registered along with the
second HCD. This is required for cold plugged USB devices to be detected
in certain PCIe USB cards (like Inateck USB card connected to AM64 EVM
or J7200 EVM).
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f3de5d857b.
That commit broke USB on all routers that have USB always powered on and
don't require toggling any GPIO. It's a majority of devices actually.
The original code worked and seemed safe: vcc GPIO is optional and
bcma_hci_platform_power_gpio() takes care of checking the pointer before
using it.
This revert fixes:
[ 10.801127] bcma_hcd: probe of bcma0:11 failed with error -2
Fixes: f3de5d857b ("USB: bcma: Add a check for devm_gpiod_get")
Cc: stable <stable@vger.kernel.org>
Cc: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20210831065419.18371-1-zajec5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use platform_register_drivers() and platform_unregister_drivers() to
register and unregister ehci platform drivers. This simplifies the code
and prevents the following build errors seen with sparc:allmodconfig.
drivers/usb/host/ehci-hcd.c:1301: error:
"PLATFORM_DRIVER" redefined
drivers/usb/host/ehci-sh.c:173:31: error:
'ehci_hcd_sh_driver' defined but not used
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210907123002.3951446-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for USB Host High Speed Port HSIC phy.
Tested-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Link: https://lore.kernel.org/r/20210910163842.1596407-3-cristian.birsan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Aspeed, HCHalted status depends on not only Run/Stop but also
ASS/PSS status.
Handshake CMD_RUN on startup instead.
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20210910073619.26095-1-neal_liu@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210911112631.10004-1-len.baker@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a number
of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9+Tw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqyQCgxWjp4VD9Ycbz1XsHRIkkERWj6WgAnRe4mCpG
n5csYXATbYUD0UdH0hru
=xZCV
-----END PGP SIGNATURE-----
Merge tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a
number of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: isp1760: otg control register access
usb: isp1760: use the right irq status bit
usb: isp1760: write to status and address register
usb: isp1760: fix qtd fill length
usb: isp1760: fix memory pool initialization
usb: typec: tcpm: Fix spelling mistake "atleast" -> "at least"
usb: dwc2: Fix spelling mistake "was't" -> "wasn't"
usb: renesas_usbhs: Fix spelling mistake "faile" -> "failed"
usb: host: xhci-rcar: Don't reload firmware after the completion
usb: xhci-mtk: allow bandwidth table rollover
usb: mtu3: fix random remote wakeup
usb: mtu3: return successful suspend status
usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint
usb: xhci-mtk: modify the SOF/ITP interval for mt8195
usb: xhci-mtk: add a member of num_esit
usb: xhci-mtk: check boundary before check tt
usb: xhci-mtk: update fs bus bandwidth by bw_budget_table
usb: xhci-mtk: fix issue of out-of-bounds array access
usb: xhci-mtk: support option to disable usb2 ports
usb: xhci-mtk: fix use-after-free of mtk->hcd
...
Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more cleanups
on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9/lg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylZNwCggKViEViSGqJFIafAZZjmI3Nt6tUAoMkRlhcd
n1MS3snS0Sq+7BdJs37M
=GyxP
-----END PGP SIGNATURE-----
Merge tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more
cleanups on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (83 commits)
tty: serial: uartlite: Use read_poll_timeout for a polling loop
tty: serial: uartlite: Use constants in early_uartlite_putc
tty: Fix data race between tiocsti() and flush_to_ldisc()
serial: vt8500: Use of_device_get_match_data
serial: tegra: Use of_device_get_match_data
serial: 8250_ingenic: Use of_device_get_match_data
tty: serial: linflexuart: Remove redundant check to simplify the code
tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
tty: serial: fsl_lpuart: enable two stop bits for lpuart32
tty: serial: fsl_lpuart: fix the wrong mapbase value
mxser: use semi-colons instead of commas
tty: moxa: use semi-colons instead of commas
tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
tty: replace in_irq() with in_hardirq()
serial: sh-sci: fix break handling for sysrq
serial: stm32: use devm_platform_get_and_ioremap_resource()
serial: stm32: use the defined variable to simplify code
Revert "arm pl011 serial: support multi-irq request"
tty: serial: samsung: Add Exynos850 SoC data
tty: serial: samsung: Fix driver data macros style
...
According to the datasheet, "Upon the completion of FW Download,
there is no need to write or reload FW.". Otherwise, it's possible
to cause unexpected behaviors. So, adds such a condition.
Fixes: 4ac8918f3a ("usb: host: xhci-plat: add support for the R-Car H2 and M2 xHCI controllers")
Cc: stable@vger.kernel.org # v3.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210827063227.81990-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-mtk has 64 slots for periodic bandwidth calculations and each
slot represents byte budgets on a microframe. When an endpoint's
allocation sits on the boundary of the table, byte budgets' slot
can be rolled over but the current implementation doesn't.
This patch allows the microframe index rollover and prevent
out-of-bounds array access.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210827033105.26595-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent attempt to handle an unknown ROM state in the commit
d143825baf ("usb: renesas-xhci: Fix handling of unknown ROM state")
resulted in a regression and reverted later by the commit 44cf53602f
("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"").
The problem of the former fix was that it treated the failure of
firmware loading as a fatal error. Since the firmware files aren't
included in the standard linux-firmware tree, most users don't have
them, hence they got the non-working system after that. The revert
fixed the regression, but also it didn't make the firmware loading
triggered even on the devices that do need it. So we need still a fix
for them.
This is another attempt to handle the unknown ROM state. Like the
previous fix, this also tries to load the firmware when ROM shows
unknown state. In this patch, however, the failure of a firmware
loading (such as a missing firmware file) isn't handled as a fatal
error any longer when ROM has been already detected, but it falls back
to the ROM mode like before. The error is returned only when no ROM
is detected and the firmware loading failed.
Along with it, for simplifying the code flow, the detection and the
check of ROM is factored out from renesas_fw_check_running() and done
in the caller side, renesas_xhci_check_request_fw(). It avoids the
redundant ROM checks.
The patch was tested on Lenovo Thinkpad T14 gen (BIOS 1.34). Also it
was confirmed that no regression is seen on another Thinkpad T14
machine that has worked without the patch, too.
Fixes: 44cf53602f ("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1189207
Link: https://lore.kernel.org/r/20210826124127.14789-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-mtk depends on xhci's internal virt_dev when it retrieves its
internal data from usb_host_endpoint both in add_endpoint and
drop_endpoint callbacks. But when setup packet was retired by
transaction errors in xhci_setup_device() path, a virt_dev for the slot
is newly created with real_port 0. This leads to xhci-mtks's NULL pointer
dereference from drop_endpoint callback as xhci-mtk assumes that virt_dev's
real_port is always started from one. The similar problems were addressed
by [1] but that can't cover the failure cases from setup_device.
This patch drops the usages of xhci's virt_dev in xhci-mtk's drop_endpoint
callback by adopting hashtable for searching mtk's schedule entity
from a given usb_host_endpoint pointer instead of searching a linked list.
So mtk's drop_endpoint callback doesn't have to rely on virt_dev at all.
[1] f351f4b63d ("usb: xhci-mtk: fix oops when unbind driver")
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210826025144.51992-5-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 4 USB controllers on MT8195, the controllers (IP1~IP3,
exclude IP0) have a wrong default SOF/ITP interval which is
calculated from the frame counter clock 24Mhz by default, but
in fact, the frame counter clock is 48Mhz, so we should set
the accurate interval according to 48Mhz for those controllers.
Note: the first controller no need set it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1629189389-18779-9-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use @bw_budget_table[] to update fs bus bandwidth due to
not all microframes consume @bw_cost_per_microframe, see
setup_sch_info().
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1629189389-18779-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bus bandwidth array access is based on esit, increase one
will cause out-of-bounds issue; for example, when esit is
XHCI_MTK_MAX_ESIT, will overstep boundary.
Fixes: 7c986fbc16 ("usb: xhci-mtk: get the microframe boundary for ESIT")
Cc: <stable@vger.kernel.org>
Reported-by: Stan Lu <stan.lu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1629189389-18779-5-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to disable specific usb2 host ports, it's useful when
a usb2 port is disabled on some platforms, but enabled on others
for the same SoC.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1629189389-18779-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I find the patch introduce some issues, e.g.
1. oops happens when xhci_gen_setup() failed, and hash is not init
but try to destroy it;
2. memory leakage happens when fail to insert ep, need free sch_ep,
or insert ep after insert int list;
3. memory leakage happens when fail to allocate sch_array, need destroy
rhashtable;
4. it's better to check ep->hcpriv when drop ep;
so prefer to revert this patch, and resend it after the issues are fixed.
This reverts commit b873120995.
Cc: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210820065913.64490-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As discussed in following patch:
https://patchwork.kernel.org/patch/12420339
No need calculate number of uframes again, but should use value
form check_sch_tt(), if we plan to remove extra CS, also can do
it in check_sch_tt(). So revert this patch, and prepare to send
new patch for it.
This reverts commit 548011957d.
Cc: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210820065913.64490-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.
Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 8c869edaee ("ARM: Orion: EHCI: Add support for enabling clocks")
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we register two usb buses for each xHC, and systems with several
hosts are more and more common it is getting hard to follow the
flow of debug messages without knowing which bus they belong to
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add more debugging messages to follow what happends to a URB internally
in special cases like URB cancel, halted endpoints and endpoint reset.
Helps tracking issues like URB never given back by host.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5d5323a6f3.
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only TDs with status TD_CLEARING_CACHE will be given back after
cache is cleared with a set TR deq command.
xhci_invalidate_cached_td() failed to set the TD_CLEARING_CACHE status
for some cancelled TDs as it assumed an endpoint only needs to clear the
TD it stopped on.
This isn't always true. For example with streams enabled an endpoint may
have several stream rings, each stopping on a different TDs.
Note that if an endpoint has several stream rings, the current code
will still only clear the cache of the stream pointed to by the last
cancelled TD in the cancel list.
This patch only focus on making sure all canceled TDs are given back,
avoiding hung task after device removal.
Another fix to solve clearing the caches of all stream rings with
cancelled TDs is needed, but not as urgent.
This issue was simultanously discovered and debugged by
by Tao Wang, with a slightly different fix proposal.
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: <stable@vger.kernel.org> #5.12
Reported-by: Tao Wang <wat@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes static char buffer usage in the following decode functions:
xhci_decode_ctrl_ctx()
xhci_decode_slot_context()
xhci_decode_usbsts()
xhci_decode_doorbell()
xhci_decode_ep_context()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor changes are needed in other xhci code as these functions are also
used elsewhere
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes static char buffer usage in the following decode functions:
xhci_decode_trb()
xhci_decode_ptortsc()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor chanes are needed in xhci debugfs code as these functions are also
used there. Changes include moving XHCI_MSG_MAX definititon from
xhci-trace.h to xhci.h
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor struct ehci_regs to avoid accessing beyond the end of
port_status. This change results in no difference in the final
object code.
Avoids several warnings when building with -Warray-bounds:
drivers/usb/host/ehci-brcm.c: In function 'ehci_brcm_reset':
drivers/usb/host/ehci-brcm.c:113:32: warning: array subscript 16 is above array bounds of 'u32[15]' {aka 'unsigned int[15]'} [-Warray-bounds]
113 | ehci_writel(ehci, 0x00800040, &ehci->regs->port_status[0x10]);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/ehci.h:274,
from drivers/usb/host/ehci-brcm.c:15:
./include/linux/usb/ehci_def.h:132:7: note: while referencing 'port_status'
132 | u32 port_status[HCS_N_PORTS_MAX];
| ^~~~~~~~~~~
Note that the documentation around this proprietary register was
confusing. If "USB_EHCI_INSNREG00" is at port_status[0x0f], its offset
would be 0x80 (not 0x90). The comments have been adjusted to fix this
apparent typo.
Fixes: 9df231511b ("usb: ehci: Add new EHCI driver for Broadcom STB SoC's")
Cc: Al Cooper <alcooperx@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818173018.2259231-3-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1b00767fd8 ("MIPS: Remove PMC MSP71xx platform") deletes
./arch/mips/pmcs-msp71xx/Kconfig, including its config MSP_HAS_USB.
Hence, since then, the corresponding EHCI support for on-chip PMC MSP71xx
USB controller is dead code. Remove this dead driver.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210818071137.22711-2-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to usb_add_hcd() (which takes
*unsigned* IRQ #), causing request_irq() that it calls to fail with
-EINVAL, overriding an original error code. Stop calling usb_add_hcd()
with the invalid IRQ #s.
Fixes: 78c73414f4 ("USB: ohci: add support for tmio-ohci cell")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/402e1a45-a0a4-0e08-566a-7ca1331506b1@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently xhci-mtk needs software-managed bandwidth allocation for
periodic endpoints, it allocates the microframe index for the first
start-split packet for each endpoint. As this index allocation logic
should avoid the conflicts with other full/low-speed periodic endpoints,
it uses the worst case byte budgets on high-speed bus bandwidth
For example, for an isochronos IN endpoint with 192 bytes budget,
it will consume the whole 4 u-frames(188 * 4) while the actual
full-speed bus budget should be just 192bytes.
This patch changes the low/full-speed bandwidth allocation logic
to use "approximate" best case budget for lower speed bandwidth
management. For the same endpoint from the above example, the
approximate best case budget is now reduced to (188 * 2) bytes.
Without this patch, many usb audio headsets with 3 interfaces
(audio input, audio output, and HID) cannot be configured
on xhci-mtk.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210805133937.1.Ia8174b875bc926c12ce427a5a1415dea31cc35ae@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-mtk depends on xhci's internal virt_dev when it retrieves its
internal data from usb_host_endpoint both in add_endpoint and
drop_endpoint callbacks. But when setup packet was retired by
transaction errors in xhci_setup_device() path, a virt_dev for the slot
is newly created with real_port 0. This leads to xhci-mtks's NULL pointer
dereference from drop_endpoint callback as xhci-mtk assumes that virt_dev's
real_port is always started from one. The similar problems were addressed
by [1] but that can't cover the failure cases from setup_device.
This patch drops the usages of xhci's virt_dev in xhci-mtk's drop_endpoint
callback by adopting rhashtable for searching mtk's schedule entity
from a given usb_host_endpoint pointer instead of searching a linked list.
So mtk's drop_endpoint callback doesn't have to rely on virt_dev at all.
[1] https://lore.kernel.org/r/1617179142-2681-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210805133731.1.Icc0f080e75b1312692d4c7c7d25e7df9fe1a05c2@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SAMA7G5 suspending ports will cut the access to OHCI registers and
any subsequent access to them will lead to CPU being blocked trying to
access that memory. Same thing happens on resume: if OHCI memory is
accessed before resuming ports the CPU will block on that access. The
OCHI memory is accessed on suspend/resume though
ohci_suspend()/ohci_resume().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210721132905.1970713-1-claudiu.beznea@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the fixes in here, and this resolves a merge issue with
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to call platform_get_irq() when the driver's probe()
method calls usb_add_hcd() -- the platform_get_irq()'s result will have
been stored already in the 'irq' local variable...
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/3e4ad969-f2ae-32f7-53fd-ea369f140703@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mv_ehci_enable() did not disable and unprepare clocks in case of
failures of phy_init(). Besides, it did not take into account failures
of ehci_clock_enable() (in effect, failures of clk_prepare_enable()).
The patch fixes both issues and gets rid of redundant wrappers around
clk_prepare_enable() and clk_disable_unprepare() to simplify this a bit.
Found by Linux Driver Verification project (linuxtesting.org).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Link: https://lore.kernel.org/r/20210708083056.21543-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should acquire the actual_length of an iso packet
from the iTD directly using FOTG210_ITD_LENGTH() macro.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-4-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we should make use of the
usb_endpoint_* helpers instead and remove the unnecessary
max_packet()/hb_mult() macro.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-3-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cb6a0db8fd for the
same reason as commit 43b78f1155 in the
ehci-hcd driver.
Alan writes:
What you can't see just from reading the patch is that in both
cases (ehci->itd_pool and ehci->sitd_pool) there are two
allocation paths -- the two branches of an "if" statement -- and
only one of the paths calls dma_pool_[z]alloc. However, the
memset is needed for both paths, and so it can't be eliminated.
Given that it must be present, there's no advantage to calling
dma_pool_zalloc rather than dma_pool_alloc.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Link: https://lore.kernel.org/r/20210627125747.127646-2-kelly.devilliv@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a66d21d7db ("usb: xhci: Add support for Renesas controller with
memory") added renesas_usb_fw.mem firmware reference to xhci-pci. Thus
modinfo indicates xhci-pci.ko has "firmware: renesas_usb_fw.mem". But
the firmware is only actually used with CONFIG_USB_XHCI_PCI_RENESAS. An
unusable firmware reference can trigger safety checkers which look for
drivers with unmet firmware dependencies.
Avoid referring to renesas_usb_fw.mem in circumstances when it cannot be
loaded (when CONFIG_USB_XHCI_PCI_RENESAS isn't set).
Fixes: a66d21d7db ("usb: xhci: Add support for Renesas controller with memory")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Thelen <gthelen@google.com>
Link: https://lore.kernel.org/r/20210702071224.3673568-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.
To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.
Fixes: 2d53139f31 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MSI is used by the ehci-hcd driver, it can cause lost interrupts which
results in EHCI only continuing to work due to a polling fallback. But the
reliance of polling drastically reduces performance of any I/O through EHCI.
Interrupts are lost as the EHCI interrupt handler does not safely handle
edge-triggered interrupts. It fails to ensure all interrupt status bits are
cleared, which works with level-triggered interrupts but not the
edge-triggered interrupts typical from using MSI.
To fix this problem, check if the driver may have raced with the hardware
setting additional interrupt status bits and clear status until it is in a
stable state.
Fixes: 306c54d0ed ("usb: hcd: Try MSI interrupts on PCI devices")
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Link: https://lore.kernel.org/r/20210715213744.GA44506@redhat
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.
When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.
To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.
checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.
If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.
CPU0 CPU1
(hub thread) (xhci event handler)
xhci_hub_status_data()
status = bus_state->resuming_ports;
<Interrupt>
handle_port_status()
spin_lock()
bus_state->resuming_ports = 1
set_flag(HCD_FLAG_POLL_RH)
spin_unlock()
spin_lock()
if (!status)
clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()
Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d143825baf.
Justin reports some of his systems now fail as result of this commit:
xhci_hcd 0000:04:00.0: Direct firmware load for renesas_usb_fw.mem failed with error -2
xhci_hcd 0000:04:00.0: request_firmware failed: -2
xhci_hcd: probe of 0000:04:00.0 failed with error -2
The revert brings back the original issue the commit tried to solve but
at least unbreaks existing systems relying on previous behavior.
Cc: stable@vger.kernel.org
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Justin Forbes <jmforbes@linuxtx.org>
Reported-by: Justin Forbes <jmforbes@linuxtx.org>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Fixes: d143825baf ("usb: renesas-xhci: Fix handling of unknown ROM state")
Link: https://lore.kernel.org/r/20210719070519.41114-1-mdf@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM3EA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGewCeMg7YvtCnqFBNebC+GfKpFTgWxO4AnAppjSrZ
RPGQgfZdWmx7daCXWbSK
=u68a
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEESH4wyp42V4tXvYsjUqAMR0iAlPIFAmDa2mEACgkQUqAMR0iA
lPKBiBAAgvhNnaRVR6/GBVrv5jYM8obJM7PHPxp8dh+ZRb1mDyL1ZDU2r7lmQjMD
ORBN5eK6pXk/gVabXR5lY0B7vQ8phJmYO98Lk2E3n9ZTgMkTHQ5WOHzBpt93gd/y
l9m00ZD0YcHrkmM1fq73FuZVEMzPk85cjTe8n6JeHJgSAdoOY/rl61Cn57ZHFIa4
DkpdNGkJaf77UIWOc8NLAXOdSD9NxSGycHXpU0q8QO9UFq+Le2qN4OPj3S1CNCO2
ciy+VcW1VQ/BesPPlBIk3ImHWPS4ty3n4EYFzNm+saElIaWxyhNBXAvcBAK/x9LK
3QibfBFwbS3sllhnk96Z24UaWWMg2AygbV2aqd3xMLpW3XD6q/MVnWGHfayhnmYj
aNcWpldIjwDH4iZJ5vnD4KewQpYp+Jc5Hqv6UyIf1O8nEvvQubrDXjSDLLcbZFI1
m2cs9DTc5ezyX/DifBsViDbw8hPjJg7QAbRjVk1EfVQrH090mRQoSoQQI4QtuMEi
pPiTALNG1HRKIoYrKxQMB43JvZ1zjaSbtNbW4JJ9Bm3kxFZ/Oa8NXzE5BOjeykZm
bCePtc018GZaGNW0z/Zr460c/Tuaj8fZSzUOj9Xnw5Hv4G3W5+5EqDy7sU/GTPjL
It9rAZYo+cM9vp1BD2343YPZgnChWHaW0BF/WDqFAhLd9av/WKI=
=Oa1c
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Add %pt[RT]s modifier to vsprintf(). It overrides ISO 8601 separator
by using ' ' (space). It produces "YYYY-mm-dd HH:MM:SS" instead of
"YYYY-mm-ddTHH:MM:SS".
- Correctly parse long row of numbers by sscanf() when using the field
width. Add extensive sscanf() selftest.
- Generalize re-entrant CPU lock that has already been used to
serialize dump_stack() output. It is part of the ongoing printk
rework. It will allow to remove the obsoleted printk_safe buffers and
introduce atomic consoles.
- Some code clean up and sparse warning fixes.
* tag 'printk-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: fix cpu lock ordering
lib/dump_stack: move cpu lock to printk.c
printk: Remove trailing semicolon in macros
random32: Fix implicit truncation warning in prandom_seed_state()
lib: test_scanf: Remove pointless use of type_min() with unsigned types
selftests: lib: Add wrapper script for test_scanf
lib: test_scanf: Add tests for sscanf number conversion
lib: vsprintf: Fix handling of number field widths in vsscanf
lib: vsprintf: scanf: Negative number must have field width > 1
usb: host: xhci-tegra: Switch to use %ptTs
nilfs2: Switch to use %ptTs
kdb: Switch to use %ptTs
lib/vsprintf: Allow to override ISO 8601 date and time separator
This patch is used to relax bandwidth schedule by allowing multiple
Start-Split in the same microframe.
Reviewed-and-Tested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1623995165-25759-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The continue statement at the end of a for-loop has no effect,
remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Continue has no effect")
Cc: Mathias Nyman <mathias.nyman@intel.com>
Link: https://lore.kernel.org/r/20210618090447.99114-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken task->state references and let wake_up_process() DTRT.
The anti-pattern in these patches breaks the ordering of ->state vs
COND as described in the comment near set_current_state() and can lead
to missed wakeups:
(OoO load, observes RUNNING)<-.
for (;;) { |
t->state = UNINTERRUPTIBLE; |
smp_mb(); ,-----> | (observes !COND)
| /
if (COND) ---------' | COND = 1;
break; `- if (t->state != RUNNING)
wake_up_process(t); // not done
schedule(); // forever waiting
}
t->state = TASK_RUNNING;
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210611082838.160855222@infradead.org
This reverts commit c950686b38 as the
patch series is causing build issues in linux-next at the moment.
Cc: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/YMuRcrE8xlWnFSWW@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when system is doing s4, the process of xhci_resume may be as below:
1、xhci_mem_cleanup
2、xhci_init->xhci_mem_init->xhci_mem_cleanup(when memory is not enough).
xhci_mem_cleanup will be executed twice when system is out of memory.
xhci->port_caps is freed in xhci_mem_cleanup,but it isn't set to NULL.
It will be freed twice when xhci_mem_cleanup is called the second time.
We got following bug when system resumes from s4:
kernel BUG at mm/slub.c:309!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
CPU: 0 PID: 5929 Tainted: G S W 5.4.96-arm64-desktop #1
pc : __slab_free+0x5c/0x424
lr : kfree+0x30c/0x32c
Call trace:
__slab_free+0x5c/0x424
kfree+0x30c/0x32c
xhci_mem_cleanup+0x394/0x3cc
xhci_mem_init+0x9ac/0x1070
xhci_init+0x8c/0x1d0
xhci_resume+0x1cc/0x5fc
xhci_plat_resume+0x64/0x70
platform_pm_thaw+0x28/0x60
dpm_run_callback+0x54/0x24c
device_resume+0xd0/0x200
async_resume+0x24/0x60
async_run_entry_fn+0x44/0x110
process_one_work+0x1f0/0x490
worker_thread+0x5c/0x450
kthread+0x158/0x160
ret_from_fork+0x10/0x24
Original patch that caused this issue was backported to 4.4 stable,
so this should be backported to 4.4 stabe as well.
Fixes: cf0ee7c60c ("xhci: Fix memory leak when caching protocol extended capability PSI tables - take 2")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: Tao Xue <xuetao09@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the urb->actual_length to bytes successfully copied in case all bytes
weren't copied from a temporary buffer to the URB sg list.
Also print a debug message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save a bit of power by not interrupting so often by default if
XHCI_AVOID_BEI quirk is set.
In normal cases the xhci driver will only generate an interrupt on the last
isochronous TRB of an URB. In a common UVC webcam usecase there are 32 TRBs
per URB.
if AVOID_BEI flag is set then xhci driver will force an interrupt every 8th
isoc TRB to make sure the event ring doesn't get too full.
This is however way too frequent in common single webcam use cases, causing
1000 interrupts/sec and thus poor powermanagement performance.
Instead start with interrupting every 32 isoc TRB, and halve it in case
event ring becomes half-full. Stop halving when reaching a rate of every
8th trb.
This is a one way solution. If interrupt rate is increased it will stay
high until driver is reloaded. The highest rate is the same as the old
default rate.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want those around confusing people.
ERST_NUM_SEGS is used both when allocating event ring segments, and when
allocating entries in the event ring segment table (erst).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are continue statements at the end of loops that have
no effect and are redundant. Remove them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Continue has no effect")
Link: https://lore.kernel.org/r/20210617123826.13764-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function. of_node_put() on it before exitting
this function.
Fixes: 971ee24706 ("usb: xhci: tegra: Enable ELPG for runtime/system PM")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210616044519.2183826-2-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
