Andrew Lunn says:
====================
smsc W=1 warning fixes
Fixup various W=1 warnings, and then add COMPILE_TEST support, which
explains why these where missed on the previous pass.
v2:
Use while (0)
Rework buffer alignment to make it clearer
v3:
Access the length from the hardware and Use __always_unused to tell the
compiler we want to discard the value.
====================
Link: https://lore.kernel.org/r/20201110030248.1480413-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Improve the build testing of these SMSC drivers by enabling them when
COMPILE_TEST is selected.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/smsc/smc911x.c: In function ‘smc911x_hardware_send_pkt’:
drivers/net/ethernet/smsc/smc911x.c:471:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
471 | cmdA = (((u32)skb->data & 0x3) << 16) |
When built on 64bit targets, the skb->data pointer cannot be cast to a
u32 in a meaningful way. Use uintptr_t instead.
Suggested-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the compiler always sees the parameters passed to the DBG()
macro, it gives an error message about wrong parameters. The comment
says it all:
/* ndev is not valid yet, so avoid passing it in. */
DBG(SMC_DEBUG_FUNC, "--> %s\n", __func__);
You cannot not just pass a parameter!
The DBG does not seem to have any real value, to just remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/smsc/smc911x.c: In function ‘smc911x_timeout’:
drivers/net/ethernet/smsc/smc911x.c:1251:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
1251 | int status, mask;
The status is read in order to print it via the DBG macro. However,
due to the way DBG is disabled, the compiler never sees it being used.
Change the DBG macro to actually make use of the passed parameters,
and the leave the optimiser to remove the unwanted code inside the
while (0).
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/smsc/smc911x.c: In function ‘smc911x_phy_interrupt’:
drivers/net/ethernet/smsc/smc911x.c:976:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
976 | int status;
A comment indicates the status needs to be read from the PHY,
otherwise bad things happen. But due to the macro magic, it is hard to
perform the read without assigning it to a variable. So add
_always_unused attribute to status to tell the compiler we don't
expect to use the value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/smsc/smc91x.c:2199: warning: Function parameter or member 'dev' not described in 'try_toggle_control_gpio'
drivers/net/ethernet/smsc/smc91x.c:2199: warning: Function parameter or member 'desc' not described in 'try_toggle_control_gpio'
drivers/net/ethernet/smsc/smc91x.c:2199: warning: Function parameter or member 'name' not described in 'try_toggle_control_gpio'
drivers/net/ethernet/smsc/smc91x.c:2199: warning: Function parameter or member 'index' not described in 'try_toggle_control_gpio'
drivers/net/ethernet/smsc/smc91x.c:2199: warning: Function parameter or member 'value' not described in 'try_toggle_control_gpio'
drivers/net/ethernet/smsc/smc91x.c:2199: warning: Function parameter or member 'nsdelay' not described in 'try_toggle_control_gpio'
Document these parameters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/smsc/smc91x.c:706:51: warning: variable ‘pkt_len’ set but not used [-Wunused-but-set-variable]
706 | unsigned int saved_packet, packet_no, tx_status, pkt_len;
The read of the packet length in the descriptor probably needs to be
kept in order to keep the hardware happy. So tell the compiler we
don't expect to use the value by using the __always_unused attribute.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The initialization for 'err' with '-ENOSYS' is redundant and
can be removed, as it is updated soon and not used.
Changes since v1:
- Move the err declaration below struct sock *sk
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Link: https://lore.kernel.org/r/5faa01d5.1c69fb81.8451c.cb5b@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn says:
====================
xilinx_emaclite W=1 fixes
kerneldoc, pointer issues, and add COMPILE_TEST support to easy
finding future issues via build testing.
v2:
- Use uintptr_t instead of long
- Added Acked-by's.
====================
Link: https://lore.kernel.org/r/20201110024024.1479741-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To improve build testing of this driver, add COMPILE_TEST support.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet//xilinx/xilinx_emaclite.c:341:35: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
341 | addr = (void __iomem __force *)((u32 __force)addr ^
Use uintptr_t instead of u32 to avoid problems on 64 bit systems.
Also, cast the address to an unsigned long for printing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The txqueue parameter to the watchdog callback is unused in this
driver. But it still needs to be documented.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nfp_cpp_from_nfp6000_pcie() returns ERR_PTR() and never returns
NULL. The NULL test should be removed, also return correct err.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Link: https://lore.kernel.org/r/20201112145852.6580-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Po-Hsu Lin says:
====================
selftests: pmtu.sh: improve the test result processing
The pmtu.sh test script treats all non-zero return code as a failure,
thus it will be marked as FAILED when some sub-test got skipped.
This patchset will:
1. Use the kselftest framework skip code $ksft_skip to replace the
hardcoded SKIP return code.
2. Improve the result processing, the test will be marked as PASSED
if nothing goes wrong and not all the tests were skipped.
====================
Link: https://lore.kernel.org/r/20201110020049.6705-1-po-hsu.lin@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This test will treat all non-zero return codes as failures, it will
make the pmtu.sh test script being marked as FAILED when some
sub-test got skipped.
Improve the result processing by
* Only mark the whole test script as SKIP when all of the
sub-tests were skipped
* If the sub-tests were either passed or skipped, the overall
result will be PASS
* If any of them has failed with return code 1 or anything bad
happened (e.g. return code 127 for command not found), the
overall result will be FAIL
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This test uses return code 2 as a hard-coded skipped state, let's use
the kselftest framework skip code variable $ksft_skip instead to make
it more readable and easier to maintain.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of the other chip info constants have helpers to get at them; add
one for max_vid to keep things consistent.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201110185720.18228-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Be more consistent about the way in which the nexthop flags are set and
set them in one go.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201110102553.1924232-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In function ‘strncpy’,
inlined from ‘sky2_name’ at drivers/net/ethernet/marvell/sky2.c:4903:3,
inlined from ‘sky2_probe’ at drivers/net/ethernet/marvell/sky2.c:5049:2:
./include/linux/string.h:297:30: warning: ‘__builtin_strncpy’ specified bound 16 equals destination size [-Wstringop-truncation]
None of the device names are 16 characters long, so it was never an
issue. But replace the strncpy with an snprintf() to prevent the
theoretical overflow.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/20201110023222.1479398-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add myself to cover the Hirschmann Hellcreek TSN Ethernet Switch Driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20201110071829.7467-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vincent Bernat says:
====================
net: evaluate net.ipvX.conf.all.* sysctls
Some per-interface sysctls are ignoring the "all" variant. This
patchset fixes some of them when such a sysctl is handled as a
boolean. This includes:
- net.ipvX.conf.all.disable_policy
- net.ipvX.conf.all.disable_policy.disable_xfrm
- net.ipv4.conf.all.proxy_arp_pvlan
- net.ipvX.conf.all.ignore_routes_with_linkdown
Two sysctls are still ignoring the "all" variant as it wouldn't make
much sense for them:
- net.ipv4.conf.all.tag
- net.ipv4.conf.all.medium_id
Ideally, the "all" variant should be removed, but there is no simple
alternative to DEVINET_SYSCTL_* macros that would allow one to not
expose and "all" entry.
====================
Link: https://lore.kernel.org/r/20201107193515.1469030-1-vincent@bernat.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The disable_policy and disable_xfrm are a per-interface sysctl to
disable IPsec policy or encryption on an interface. However, while a
"all" variant is exposed, it was a noop since it was never evaluated.
We use the usual "or" logic for this kind of sysctls.
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduced in 65324144b5, the "proxy_arp_vlan" sysctl is a
per-interface sysctl to tune proxy ARP support for private VLANs.
While the "all" variant is exposed, it was a noop and never evaluated.
We use the usual "or" logic for this kind of sysctls.
Fixes: 65324144b5 ("net: RFC3069, private VLAN proxy arp support")
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduced in 0eeb075fad, the "ignore_routes_with_linkdown" sysctl
ignores a route whose interface is down. It is provided as a
per-interface sysctl. However, while a "all" variant is exposed, it
was a noop since it was never evaluated. We use the usual "or" logic
for this kind of sysctls.
Tested with:
ip link add type veth # veth0 + veth1
ip link add type veth # veth1 + veth2
ip link set up dev veth0
ip link set up dev veth1 # link-status paired with veth0
ip link set up dev veth2
ip link set up dev veth3 # link-status paired with veth2
# First available path
ip -4 addr add 203.0.113.${uts#H}/24 dev veth0
ip -6 addr add 2001:db8:1::${uts#H}/64 dev veth0
# Second available path
ip -4 addr add 192.0.2.${uts#H}/24 dev veth2
ip -6 addr add 2001:db8:2::${uts#H}/64 dev veth2
# More specific route through first path
ip -4 route add 198.51.100.0/25 via 203.0.113.254 # via veth0
ip -6 route add 2001:db8:3::/56 via 2001:db8:1::ff # via veth0
# Less specific route through second path
ip -4 route add 198.51.100.0/24 via 192.0.2.254 # via veth2
ip -6 route add 2001:db8:3::/48 via 2001:db8:2::ff # via veth2
# H1: enable on "all"
# H2: enable on "veth0"
for v in ipv4 ipv6; do
case $uts in
H1)
sysctl -qw net.${v}.conf.all.ignore_routes_with_linkdown=1
;;
H2)
sysctl -qw net.${v}.conf.veth0.ignore_routes_with_linkdown=1
;;
esac
done
set -xe
# When veth0 is up, best route is through veth0
ip -o route get 198.51.100.1 | grep -Fw veth0
ip -o route get 2001:db8:3::1 | grep -Fw veth0
# When veth0 is down, best route should be through veth2 on H1/H2,
# but on veth0 on H2
ip link set down dev veth1 # down veth0
ip route show
[ $uts != H3 ] || ip -o route get 198.51.100.1 | grep -Fw veth0
[ $uts != H3 ] || ip -o route get 2001:db8:3::1 | grep -Fw veth0
[ $uts = H3 ] || ip -o route get 198.51.100.1 | grep -Fw veth2
[ $uts = H3 ] || ip -o route get 2001:db8:3::1 | grep -Fw veth2
Without this patch, the two last lines would fail on H1 (the one using
the "all" sysctl). With the patch, everything succeeds as expected.
Also document the sysctl in `ip-sysctl.rst`.
Fixes: 0eeb075fad ("net: ipv4 sysctl option to ignore routes when nexthop link is down")
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Loic Poulain says:
====================
net: qrtr: Add distant node support
QRTR protocol allows a node to communicate with an other non-immediate
node via an intermdediate immediate node acting as a 'bridge':
node-0 <=> node-1 <=> node-2
This is currently not supported in this upstream version and this
series aim to fix that.
This series is V2 because changes 1, 2 and 3 have already been submitted
separately on LKML.
Changes in v2:
- Add reviewed-by tags from Bjorn and Mani
- Fixing checkpatch issue reported by Jakub
====================
Link: https://lore.kernel.org/r/1604684010-24090-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Distant QRTR nodes can be accessed via an other node that acts as
a bridge. When the a QRTR endpoint associated to a bridge node is
released, all the linked distant nodes should also be released.
This patch fixes endpoint release by:
- Submitting QRTR BYE message locally on behalf of all the nodes
accessible through the endpoint.
- Removing all the routable node IDs from radix tree pointing to
the released node endpoint.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This will be requested for allocating control packet in atomic context.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to reach non-immediate remote node services that are
accessed through an intermediate node, the route to the remote
node needs to be saved.
E.g for a [node1 <=> node2 <=> node3] network
- node2 forwards node3 service to node1
- node1 must save node2 as route for reaching node3
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A remote endpoint (immediate neighbors node) can forward services
from other nodes (non-immadiate), in that case ctrl packet node ID
(offering distant service) can differ from the qrtr source node
(forwarding the packet).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The port ID for control messages was uncorrectly set with broadcast
node ID value, causing message to be dropped on remote side since
not passing packet filtering (cb->dst_port != QRTR_PORT_CTRL).
Fixes: d27e77a3de ("net: qrtr: Reset the node and port ID of broadcast messages")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return pointer of dwc_eth_dwmac_data's .probe isn't used, and
"probe" usually return int, so change the prototype to follow standard
way. Secondly, it can simplify the tegra_eqos_probe() code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201109160440.3a736ee3@xhacker.debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The referenced commit added in .config_intr() the part of code which upon
configuration of the IRQ state it also clears up any pending IRQ. If
there were actually pending IRQs, a read on the IRQ status register will
return something non zero. This should not result in the callback
returning an error.
Fix this by returning an error only when the result of the
phy_read_mmd() is negative.
Fixes: e11ef96d44 ("net: phy: aquantia: remove the use of .ack_interrupt()")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Link: https://lore.kernel.org/r/20201109154601.3812574-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder says:
====================
net: ipa: little fixes
This series adds a few small fixes to the IPA code.
The first patch appeared in a different form in June, and got some
pushback from David because he felt a problem that can be caught at
build time *should* be caught at build time.
https://lore.kernel.org/netdev/20200610195332.2612233-1-elder@linaro.org/
I agree with that, but in this case the "problem" was never actually
a problem. There's a little more explanation on the patch, but
basically now we remove the BUILD_BUG_ON() call entirely.
The second deletes a line of code that isn't needed.
The third converts a warning message to be a debug, as requested by
Stephen Boyd.
And the last one just gets rid of an error message that would be
output after a different message had already reported a problem.
====================
Link: https://lore.kernel.org/r/20201109165635.5449-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need for gsi_modem_channel_halt() to report an error,
because gsi_generic_command() will already have done that if the
command times out. So get rid of the extra message.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When we determine from hardware what the size of IPA memory is
we compare it against what we learned about it from DT.
If DT defines a region that's larger than actual memory, we use the
smaller actual size and issue a warning.
If DT defines a smaller region than actual memory we issue a warning
too. But in this case the difference is harmless; so rather than
issuing a warning, just provide a debug message instead.
Reorder these checks so the one that matters more is done first.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Delete a spurious line of code in ipa_hardware_config(). It reads a
register value then ignores the value, so is completely unnecessary.
Add a missing word in a comment.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following call in ipa_validate_build() is erroneous:
BUILD_BUG_ON(sizeof(struct gsi_trans) > 128);
The fact is, it is not a bug for the size of a GSI transaction to be
bigger than 128 bytes. The correct operation of the driver is not
dependent on the size of this structure. The only consequence of
the transaction being large is that the amount of memory required
is larger.
The problem this was trying to flag is that a *slight* increase in
the size of this structure will have a disproportionate effect on
the amount of memory used. E.g. if the structure grew to 132 bytes
the memory requirement for the transaction arrays would be about
double.
With various debugging build flags enabled, the size grows to 160
bytes. But there's no reason to treat that as a build-time bug.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
inet: prevent skb changes in udp{4|6}_lib_lookup_skb()
This came while reviewing Alexander Lobakin patch against UDP GRO:
We want to make sure skb wont be changed by these helpers
while it is owned by GRO stack.
====================
Link: https://lore.kernel.org/r/20201109231349.20946-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The skb is needed only to fetch the keys for the lookup.
Both functions are used from GRO stack, we do not want
accidental modification of the skb.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
inet_sdif() does not modify the skb.
This will permit propagating the const qualifier in
udp{4|6}_lib_lookup_skb() functions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The left shift of u16 variable high is promoted to the type int and
then sign extended to a 64 bit u64 value. If the top bit of high is
set then the upper 32 bits of the result end up being set by the
sign extension. Fix this by explicitly casting the value in high to
a u64 before left shifting by 16 places.
Also, remove the initialisation of variable value to 0 at the start
of each loop iteration as the value is never read and hence the
assignment it is redundant.
Addresses-Coverity: ("Unintended sign extension")
Fixes: e4b27ebc78 ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20201109124008.2079873-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some typos are found out by misspell-fixer tool:
$ misspell-fixer -rnv ./net/sched/
./net/sched/act_api.c:686
./net/sched/act_bpf.c:68
./net/sched/cls_rsvp.h:241
./net/sched/em_cmp.c:44
./net/sched/sch_pie.c:408
Fix typos found by misspell-fixer.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/5fa8e9d4.1c69fb81.5d889.5c64@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The '!=' expression itself is bool, no need to convert it to bool.
Fix the following coccicheck warning:
./drivers/net/ethernet/aquantia/atlantic/aq_nic.c:1477:34-39: WARNING: conversion to bool not needed here
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1604797919-10157-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The initialization for 'err' with '-EINVAL' is redundant and
can be removed, as it is updated soon.
Changes since v1:
- Remove redundant empty line
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Link: https://lore.kernel.org/r/20201108010541.12432-1-dong.menglong@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some systems have rp_filter=1 as default configuration. This breaks
bareudp.sh as the intermediate namespaces handle part of the routing
with regular IPv4 routes but the reverse path is done with tc
(flower/tunnel_key/mirred).
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://lore.kernel.org/r/28140b7d20161e4f766b558018fe2718f9bc1117.1604767577.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to commit fda55eca5a
("net: introduce skb_transport_header_was_set()"), avoid resetting
transport offsets that were already set by GRO layer. This not only
mirrors the behavior of __netif_receive_skb_core(), but also makes
sense when it comes to UDP GSO fraglists forwarding: transport offset
of such skbs is set only once by GRO receive callback and remains
untouched and correct up to the xmitting driver in 1:1 case, but
becomes junk after untagging in ingress VLAN case and breaks UDP
GSO offload. This does not happen after this change, and all types
of forwarding of UDP GSO fraglists work as expected.
Since v1 [1]:
- keep the code 1:1 with __netif_receive_skb_core() (Jakub).
[1] https://lore.kernel.org/netdev/zYurwsZRN7BkqSoikWQLVqHyxz18h4LhHU4NFa2Vw@cp4-web-038.plabs.ch
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/7JgIkgEztzt0W6ZtC9V9Cnk5qfkrUFYcpN871syCi8@cp4-web-040.plabs.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit says:
====================
net: add and use dev_get_tstats64
It's a frequent pattern to use netdev->stats for the less frequently
accessed counters and per-cpu counters for the frequently accessed
counters (rx/tx bytes/packets). Add a default ndo_get_stats64()
implementation for this use case. Subsequently switch more drivers
to use this pattern.
v2:
- add patches for replacing ip_tunnel_get_stats64
Requested additional migrations will come in a separate series.
v3:
- add atomic_long_t member rx_frame_errors in patch 3 for making
counter updates atomic
====================
Link: https://lore.kernel.org/r/99273e2f-c218-cd19-916e-9161d8ad8c56@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
