OpenBlocks A6 uses second I2C with RTC of s35390a.
This supports them.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Second I2C bus is supported by 88f6282 and 88f6283.
This creates kirkwood-6282.dtsi, and defines DT table
of second I2C bus.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell 98DX412x SoC embed a kirkwood variant that does not have
pinctrl support yet. Even though this kirkwood is very similar to the
88f6281, on the MPP front a lot of pins are not available. That's why a
new kirkwood pinctrl variant is needed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Make use of the pinctrl driver for configuring all the pins, instead
of using the Orion mpp code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There are a couple of different variants of Kirkwood, which differ in
the pin muxing. These DTSI files set the correct compatibility and
define commonly used groups of pins, which board dbs files can
reference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Select the generic mvebu kirkwood pincltr driver and generic mvebu
gpio driver. This requires minor changes to the DT, and the calls to
configure plat-orion gpio driver are removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Tested-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Kirkwood & Dove can also use this driver, so expand the scope to
include all platform orion devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SolidRun CuBox has a led on a gpio pin. As there is now DT pinctrl
support for Dove, make use of a pinhog to ensure the pin is set to
gpio.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Following the ongoing conversion of Orion SoCs to DT, make use of
gpio and pinctrl drivers through DT. The main dtsi for Dove is prepared
to allow board specific descriptors to make use of pinctrl muxing.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When setting audio1 pinmux the bits in the corresponding registers
are not cleared. This fix first clears all bits and then sets the
required bits according to the selected function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There has been a change in readl/writel to require registers
addresses marked as IOMEM(). This patch takes care of this and
also replaces ORing address offsets with adding them.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB and HDD using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to SATA0 and SATA1 using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A few boards use a GPIO line to enable power to subsystems, eg USB or
SATA devices. Pull in the regulator framework as the first step to
controlling these GPIO lines are regulators.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Also enable the gpio-poweroff driver when DT is used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Given appropriate devicetree bindings, this driver registers a
pm_power_off function to set a GPIO line high/low to power down
your board.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by:Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The default chip-delay of 25us is a bit too tight for some DNS-320's,
and D-Link seem to specify 30us in their kernels for both devices.
Increase to 35us to make sure the NAND is stable.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the EHCI driver has DT support, drop old style configuration
of it and add DT in its place. Since all the boards enable the EHCI,
enable it by default in kirkwood.dtsi. Any new boards which don't have
USB can specifically disable it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Based on previous work by Michael Walle and Jason Cooper.
Made their work actually work, which required added interrupt from DT
and auxdata, along with setting the dma_mask, which DT does not
currently do.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for Plat'Home OpenBlocks A6 using the device tree
where possible.
This commit supports SATA, USB, ether and serial console.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
It has been a while since dove_defconfig was updated to recent development.
This patch adds all currently available Dove boards, including a DT-enabled
machine.
DT support requires to allow ATAGS passed by boot loader as most of them are
not yet capable of passing DT blobs. Also OF_SERIAL is enabled to actually
see the bootlog.
Finally, sdhci driver for Dove, mv_cesa, GPIO LEDs, and highmem support is
added.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit converts the 'LaCie Ethernet Disk mini v2' board to the
Device Tree. All devices that have existing Device Tree bindings are
converted over to the Device Tree, the other devices remain
instantiated in the old way, until the respective drivers get the
needed Device Tree bindings.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds basic DT support for the Orion5x SoC family. It adds
an orion5x.dtsi description of the Orion5x SoC as well as the needed
DT_MACHINE structure to support boards converted to DT in the future.
So far, the Device Tree contains the interrupt controller, the GPIO
bank, the UART controllers, the SPI controller, the watchdog, the SATA
controller, the I2C controller and the cryptographic engine.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit is a simple mechanical update of the orion5x_defconfig
file to the current kernel (i.e, just 'make orion5x_defconfig; make
savedefconfig'). Doing this update allows to more easily separate
DT-related configuration changes in the following patches.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Hello, Andrew
> > +#define NSA310_GPIO_LED_ESATA_GREEN 12
> > <..>
> > +#define NSA310_GPIO_POWER_OFF 48
>
> It looks like most of these are not used. Please remove them.
True. Fixed.
> > +static struct mtd_partition nsa310_mtd_parts[] = {
> > + {
> > + .name = "uboot",
> > + .offset = 0,
> > + .size = 0x100000,
> > + .mask_flags = MTD_WRITEABLE,
> > + }, {
> > <..>
> You should be able to put all that into DT. Take a look at
Correct. I did the conversion and tested that the partitions
can be read with dd and produce exactly the same data before and
after conversion. So, the partition offsets at least should be fine.
> > +static struct i2c_board_info __initdata nsa310_i2c_info[] = {
> > + { I2C_BOARD_INFO("adt7476", 0x2e) },
> > +};
>
> You can also do this in DT as well. kirkwood-ts219.dtsi has
>
> i2c@11000 {
> status = "okay";
> clock-frequency = <400000>;
Ok, I did convert the i2c definition to use the devicetree.
The adt7476 device itself is not at reach of device tree,
AFAIK and requires more work at there?
Thanks for your valuable comments. Following is a new patch that
should address the problems and mistakes you pointed and also
some of the pointed by Jason Cooper. The nand and i2c are now
defined at DT and I also removed the pointless defines and
ARM_APPENDED_DTB. It is based against the Linus' official
3.6 version.
Best regards,
Tero
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is a new kirkwood box made by Universal Scientific Industrial, Inc.
The product description is here:
http://www.usish.com/english/products_topkick1281p2.php
It is very similar to the dreamplug and other plug devices, with the
exception that it has room for a 2.5" SATA HDD internally.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Remove board specific gpio-fan driver registration. Moved into device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for the LaCie NAS Network Space Mini v2
(aka SafeBox). The hardware characteristics are very close to those of
the Network Space Lite v2. The main difference are:
- A GPIO fan which is only available on the NS2 Mini.
- A single USB host port is wired on the NS2 Mini. The NS2 Lite provides
an additional dual-mode USB port (host/device).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for the LaCie NAS Network Space Lite v2.
This board is derived from the Network Space v2 and a lot of hardware
characteristics are shared.
- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)
Note that the SATA LED is not compatible with the driver leds-ns2. The
LED behaviour ("on", "off" or "SATA activity blink") is controlled via
a single MPP (21).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for LaCie Network Space v2 and parents,
based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2
(Max) and Internet Space v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
mv64xxx_of_config requires that the tclk frequency be found
through the clk stuff rather than through device tree, so add
another override for the 2nd controller.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
