Support interrupt based pio mode to optimize cpu usage.
When transmitting data size is larget than 32 bytes, operates with
interrupt based pio mode.
By using the FIFORDY INT, an interrupt can be triggered when
the desired size of data has been received. Using this, we can support
interrupt based pio mode.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com
Link: https://lore.kernel.org/r/20230502062813.112434-4-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org
In polling mode, the status register is continuously read to check data
transfer completion. It can cause excessive CPU usage.
To reduce this, we can calculate the transfer time and put the sleep during
transfer.
When test on ExynosAuto9 SADK board, throughput remained the same, but
100% CPU utilization decreased to 40%.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230502062813.112434-3-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org
Previously, Polling mode was supported as quirk for SOC without DMA.
To provide more flexible support for polling mode, it changed to polling
mode when the 'dmas' property is not present in the devicetree, rather than
using a quirk.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Link: https://lore.kernel.org/r/20230502062813.112434-2-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org
Supporting multi-cs in spi drivers would require the chip_select & cs_gpiod
members of struct spi_device to be an array. But changing the type of these
members to array would break the spi driver functionality. To make the
transition smoother introduced four new APIs to get/set the
spi->chip_select & spi->cs_gpiod and replaced all spi->chip_select and
spi->cs_gpiod references with get or set API calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Acked-by: Heiko Stuebner <heiko@sntech.de> # Rockchip drivers
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org> # Aspeed driver
Reviewed-by: Dhruva Gole <d-gole@ti.com> # SPI Cadence QSPI
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> # spi-stm32-qspi
Acked-by: William Zhang <william.zhang@broadcom.com> # bcm63xx-hsspi driver
Reviewed-by: Serge Semin <fancer.lancer@gmail.com> # DW SSI part
Link: https://lore.kernel.org/r/167847070432.26.15076794204368669839@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-63-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The COUNT_VALUE in the PACKET_CNT register is 16-bit so the maximum
value is 65535. Asking the driver to transfer a larger size currently
leads to the DMA transfer timing out. Implement ->max_transfer_size()
and have the core split the transfer as needed.
Fixes: 230d42d422 ("spi: Add s3c64xx SPI Controller driver")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-5-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use NULL for dma channel pointer initialization instead of plain integer.
sparse warnings: (new ones prefixed by >>)
>> drivers/spi/spi-s3c64xx.c:387:34: sparse: sparse: Using plain integer as NULL pointer
drivers/spi/spi-s3c64xx.c:388:34: sparse: sparse: Using plain integer as NULL pointer
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 82295bc0d1 ("spi: s3c64xx: move dma_release_channel to unprepare")
Fixes: f52b03c707 ("spi: s3c64xx: requests spi-dma channel only during data transfer")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220808004851.25122-1-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add exynosautov9 spi port configuration. It supports up to 12 spis so
MAX_SPI_PORTS should be increased from 6 to 12.
It has DIV_4 as the default internal clock divider and an internal
loopback mode to run a loopback test.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220629102304.65712-5-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Modern exynos SoCs such as Exynos Auto v9 have different internal clock
divider, for example "4". To support this internal value, this adds
clk_div of the s3c64xx_spi_port_config and assign "2" as the default
value to existing s3c64xx_spi_port_config.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220629102304.65712-3-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Modern exynos SoCs can support self loopback mode via setting BIT(3) of
MODE_CFG register. Previous SoCs don't have the bit so we need to add
has_loopback field in the s3c64xx_spi_port_config. Exynos Auto v9 SoC
has the bit and it will define the field to "true".
When it is set, SPI_LOOP mode will be marked.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220629102304.65712-2-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the sequence of dma_release_channel.
Since commit f52b03c707 ("spi: s3c64xx: requests spi-dma channel only
during data transfer"),
dma_release_channel has been located in the s3c64xx_spi_transfer_one
but this makes invalid return of can_dma callback.
__spi_unmap_msg will check whether the request is requested by dma or
not via can_dma callback. When it is calling to check it, the channels
will be already released at the end of s3c64xx_spi_transfer_one so the
callback function will return always "false". So, they can't be unmapped
from __spi_unmap_msg call. To fix this, we need to add
unprepare_transfer_hardware callback and move the dma_release_channel
from s3c64xx_spi_transfer_one to there.
Fixes: f52b03c707 ("spi: s3c64xx: requests spi-dma channel only during data transfer")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220627013845.138350-1-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are pointers being set to null using use. Use NULL instead.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220612203428.2754823-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return boolean values ("true" or "false") instead of 1 or 0 from bool
function.
As reported by coccicheck:
./drivers/spi/spi-s3c64xx.c:385:9-10: WARNING: return of 0/1 in function
's3c64xx_spi_can_dma' with return type bool
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220609071250.59509-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220608081912.2083086-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current s3c64xx SPI driver acquires DMA channel during driver
probe and holds on it even when channels are not used
(no DMA transfer). This is a problem especially when all the
DMA channels are exhausted (as other IPs on the same DMA
controller also acquires DMA channel) and if a new IP/Device
requests for a DMA channel (on the same DMA controller), it won’t
get DMA channel allocated.
The said issue can be avoided if s3c64xx driver request and
release DMA channel before and after data transfer. Let’s modify
the driver to request and release DMA channel before and after
DMA mode data transfer.
Signed-off-by: Adithya K V <adithya.kv@samsung.com>
Link: https://lore.kernel.org/r/20220524140132.59300-1-adithya.kv@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Alim Akhtar:
This series adds support for the SPI controller in the Tesla FSD SoC,
also pulling in:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-spi-dt-v5.18
from the MFD tree which has dependencies for the DT bindings.
Add compatible and port configuration for spi controller
for Tesla Full Self-Driving SoC.
Cc: linux-fsd@tesla.com
Signed-off-by: Aswani Reddy <aswani.reddy@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20220308121640.27344-2-alim.akhtar@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Samsung SoC SPI driver requires to provide controller-data node
for each of SPI peripheral device nodes. Make this controller-data node
optional, so DTS could be simpler.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220124082347.32747-5-krzysztof.kozlowski@canonical.com
Convert the S3C64xx SPI host to use GPIO descriptors.
Provide GPIO descriptor tables for the one user with CS
0 and 1.
Cc: linux-samsung-soc@vger.kernel.org
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220118230915.157797-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The match data (struct s3c64xx_spi_port_config) stored in of_device_id
and platform_device_id tables is not modified by the driver and can be
handled entirely in a const-way to increase the code safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the name of s3c64xx_spi_port_config structure in kerneldoc:
drivers/spi/spi-s3c64xx.c:154: warning:
expecting prototype for struct s3c64xx_spi_info. Prototype was for struct s3c64xx_spi_port_config instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to make the code slightly smaller and to
remove the of_device_id table forward declaration.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
s3c64xx_spi_hwinit() disables interrupts. In s3c64xx_spi_probe() after
calling s3c64xx_spi_hwinit() they are enabled with the following call.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-10-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Increase timeout by 30 ms for some wiggle room and set the minimum value
to 100 ms. This ensures a non-zero value for short transfers which
may take less than 1 ms. The timeout value does not affect
performance because it is used with a completion.
Similar formula is used in other drivers e.g. sun4i, sun6i.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-9-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure the cur_speed value used in s3c64xx_enable_datapath()
to configure DMA channel and in s3c64xx_wait_for_*() to calculate the
transfer timeout is set to the actual value of (half) the clock speed.
Don't change non-CMU case, because no frequency calculation errors have
been reported.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Suggested-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-8-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove descriptions for non-existent fields and fix indentation.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-7-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename S3C64XX_SPI_SLAVE_* to S3C64XX_SPI_CS_* to match documentation.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201002122243.26849-6-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Report amount of pending data when a transfer stops due to errors.
Report if DMA was used to transfer data and print the status code.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-5-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check return values in prepare_dma() and s3c64xx_spi_config() and
propagate errors upwards.
Fixes: 788437273f ("spi: s3c64xx: move to generic dmaengine API")
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-4-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix issues with DMA transfers bigger than 512 bytes on Exynos3250. Without
the patches such transfers fail.
The vendor kernel for ARTIK5 handles CS in a simmilar way.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201002122243.26849-3-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix issues with DMA transfers bigger than 512 bytes on Exynos3250. Without
the patches such transfers fail to complete. This solution to the problem
is found in the vendor kernel for ARTIK5 boards based on Exynos3250.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20201002122243.26849-2-l.stelmach@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'quirks' not described in 's3c64xx_spi_port_config'
drivers/spi/spi-s3c64xx.c:150: warning: Function parameter or member 'clk_ioclk' not described in 's3c64xx_spi_port_config'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'pdev' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'rx_dma' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'tx_dma' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_conf' not described in 's3c64xx_spi_driver_data'
drivers/spi/spi-s3c64xx.c:189: warning: Function parameter or member 'port_id' not described in 's3c64xx_spi_driver_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Andi Shyti <andi@etezian.org>
Cc: Jaswinder Singh <jassi.brar@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Link: https://lore.kernel.org/r/20200717135424.2442271-8-lee.jones@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Since Linux v4.10 release (commit 1d9174fbc5 "PM / Runtime: Defer
resuming of the device in pm_runtime_force_resume()"),
pm_runtime_force_resume() function doesn't runtime resume device if it was
not runtime active before system suspend. Thus, driver should not do any
register access after pm_runtime_force_resume() without checking the
runtime status of the device. To fix this issue, simply move
s3c64xx_spi_hwinit() call to s3c64xx_spi_runtime_resume() to ensure that
hardware is always properly initialized. This fixes Synchronous external
abort issue on system suspend/resume cycle on newer Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some variants of the SPI controller have no DMA support, in such case
SPI transfers longer than the FIFO length are not currently properly
handled by the driver. Fix it by doing multiple transfers in the
s3c64xx_spi_transfer_one() function if the SPI transfer length exceeds
the FIFO size.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
More references to fifo_len are added in subsequent patch.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a s3c64xx_ prefix to remaining generic function names so it is clear
the code is part of the driver when grepping or looking at debug logs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi pointer argument is not used now so remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change indentation so register address offset and register bit definitions
are aligned to same column.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently timeout errors in polling I/O mode transfer are silently ignored.
Fix it by returning an error when we time out waiting on the RX FIFO level
to reach the transfer length.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The channel argument is not used and anyway it could be retrieved from
the passed driver data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tgl_spi pointer is now unused so remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the original license statement with the SPDX identifier.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer sci is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/spi/spi-s3c64xx.c:791:2: warning: Value stored to 'sci' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a92e7c3d82 ("spi: s3c64xx: consider the case when the CS
line is not connected") introduced an inconsistency between the
binding, where the disconnected CS line was marked as
'no-cs-readback', and the driver.
The driver is erroneously checking for that attribute with
property name of 'broken-cs'.
Check for 'no-cs-readback' in the driver as well.
Fixes: a92e7c3d82 ("spi: s3c64xx: consider the case when the CS line is not connected")
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We accidentally mixed up freeing the rx and tx channels which would a
leak and an oops.
Fixes: 3d63a47a38 ("spi: s3c64xx: Don't request/release DMA channels for each SPI transfer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Requesting a DMA channel might be a time consuming operation, so there is
no need to acquire and release DMA channel for each SPI transfer.
DMA channels can be requested during driver probe and kept all the time,
also because there are no shared nor dynamically allocated channels on
Samsung S3C/S5P/Exynos platforms.
While moving dma_requrest_slave_channel calls, lets switch to
dma_request_slave_channel_reason(), which returns error codes on failure,
which can be properly propagated to the caller (this for example defers
SPI probe when DMA controller is not yet available).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
