S5PV210 SoCs has 2 USB PHY interfaces, both enabled by writing zero to
S3C_PHYPWR register. HS/OTG driver uses only PHY0, so do not touch bits
related to PHY1.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/gadget/s3c-hsotg.c: In function ‘s3c_hsotg_otgreset’:
drivers/usb/gadget/s3c-hsotg.c:2816: error: ‘MHZ’ undeclared (first use in this function)
drivers/usb/gadget/s3c-hsotg.c:2816: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/s3c-hsotg.c:2816: error: for each function it appears in.)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PLL that drives the USB clock supports 3 input clocks: 12, 24 and 48Mhz.
This patch adds support to the USB driver for setting the correct register bit
according to the given clock.
This depends on the following patch:
[PATCH] ARM: S3C64XX: Add USB external clock definition
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If there is more data in the request than we could fit into a single
hardware request, then check when the OutDone event is received if
we have more data, and if so, schedule the new data instead of trying
to complete the request (and in the case of EP0, sending a 0 packet
in the middle of a transfer).
Also, move the debug message about the current transfer state before
the warning about a bad transfer.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The EP0 out limit is the same as the IN limit, so make them the same.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The maximum length for any EP0 IN request on EP0 is 127 bytes, not 128
as the driver currently has it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before trying a new setup transaction after getting an EP0 in complete
interrupt, check that the driver did not try and send more EP0 IN data
before enqueing a new setup transaction.
This fixes a bug where we cannot send all of the IN data in one go
so split the transfer, but then fail to send all the data as we start
waiting for a new OUT transaction
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Limit the IN FIFO write to a single packet per attempt at writing,
as per the specifications and ensure that we don't return fifo-full
so that we can continue writing packets if we have the space.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the dedicated FIFO mode on newer SoCs such as the S5PV210
partly to improve support and to fix the bug where any non-EP0 IN endpoint
requires its own FIFO allocation.
To fix this, we ensure that any non-zero IN endpoint is given a TXFIFO
using the same allocation method as the periodic case (all our current
hardware has enough FIFOs and FIFO memory for a 1:1 mapping) and ensure
that the necessary transmission done interrupt is enabled.
The default settings from reset for the core point all EPs at FIFO0,
used for the control endpoint. However, the controller documentation
states that all IN endpoints _must_ have a unique FIFO to avoid any
contention during transmission.
Note, this leaves us with a large IN FIFO for EP0 (which re-uses the
old NPTXFIFO) for an endpoint which cannot shift more than a pair of
packets at a time... this is a waste, but it looks like we cannot
re-allocate space to the individual IN FIFOs as they are already
maxed out (to be confirmed).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB documentation suggest that the FIFOs should be reset when a
bus reset event happens. Use the s3c_hsotg_init_fifo() to ensure that
the FIFO layout is correct and that the FIFOs are flushed before
acknowledging the reset.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In shared fifo mode (used on older SoCs) the periodic in fifo beahves
much more like a packet buffer, discarding old data when writing new
data. Avoid this by ensuring that we do not load new transactions in
when there is data sitting already in the FIFO.
Note, this may not be an observed bug, we are fixing the case that this
may happen.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a problem where we have been underestimating the space available in
the IN PTX/NPTX FIFOs by assuming that they where simply word aligned
instead of in number-of-words. This means all length calculations need
to be multiplied-by-4.
Note, we do not change the information about fifo size or start addresses
available to userspace as we assume the user can multiply by four easily
and is already knows these values are in words.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Up the FIFO size for the TX to 1024 entries, as this now seems to work
with all the cores. This fixes a problem when using large packets on
a core with MPS set to 512 can hang due to insufficient space for the
writes.
The hang arises due to getting the non-periodic FIFO empty IRQ but
not being able to satisfy any requests since there is never enough
space to write 512 bytes into the buffer. This means we end up with
a stream of interrupt requests.
It is easier to up the TX FIFO to fill the space we left for it
than to try and fix the positions in the code where we should have
limited the max-packet size to < TXFIFOSIZE, since the TXFIFOSIZE
depends on how the TX FIFOs have been setup.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MS Windows mounts removable storage in "Removal optimized mode" by
default. All the writes to the media are synchronous which is achieved
by setting FUA (Force Unit Access) bit in SCSI WRITE(10,12) commands.
This prevents I/O requests aggregation in block layer dramatically
decreasing performance.
This patch brings an option to accept or ignore mentioned bit
a) via specifying module parameter "nofua", or
b) through sysfs entry
/sys/devices/platform/_UDC_/gadget/gadget-lunX/nofua
(_UDC_ is the name of the USB Device Controller driver)
Patch is based on the work that was done by Denis Karpov for Maemo 5
platform.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bring a strict way to get the 'ro' parameter from the user.
The patch followed by this one adds another boolean parameter. To be consistent
Michał Nazarewicz proposed to use simple_strtol() in both cases (correspondend
discussion in LKML [1]). Due to simple_strtol() doesn't return error in a good
way and we have a boolean parameter the strict_strtoul() is used.
[1] http://lkml.org/lkml/2010/7/14/169
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous endpoint needs a bigger size of transfer ring. Isochronous URB
consists of multiple packets, each packet needs a isoc td to carry, and
there will be multiple trbs inserted to the ring at one time. One segment
is too small for isochronous endpoints, and it will result in
room_on_ring() check failure and the URB is failed to enqueue.
Allocate bigger ring for isochronous endpoint. 8 segments should be enough.
This will be replaced with dynamic ring expansion in the future.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements isochronous urb enqueue and interrupt handler part.
When an isochronous urb is passed to xHCI driver, first check the transfer
ring to guarantee there is enough room for the whole urb. Then update the
start_frame and interval field of the urb. Always assume URB_ISO_ASAP
is set, and never use urb->start_frame as input.
The number of isoc TDs is equal to urb->number_of_packets. One isoc TD is
consumed every Interval. Each isoc TD consists of an Isoch TRB chained to
zero or more Normal TRBs.
Call prepare_transfer for each TD to do initialization; then calculate the
number of TRBs needed for each TD. If the data required by an isoc TD is
physically contiguous (not crosses a page boundary), then only one isoc TRB
is needed; otherwise one or more additional normal TRB shall be chained to
the isoc TRB by the host.
Set TRB_IOC to the last TRB of each isoc TD. Do not ring endpoint doorbell
to start xHC procession until all the TDs are inserted to the endpoint
transer ring.
In irq handler, update urb status and actual_length, increase
urb_priv->td_cnt. When all the TDs are completed(td_cnt is equal to
urb_priv->length), giveback the urb to usbcore.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add urb_priv data structure to xHCI driver. This structure allows multiple
xhci TDs to be linked to one urb, which is essential for isochronous
transfer. For non-isochronous urb, only one TD is needed for one urb;
for isochronous urb, the TD number for the urb is equal to
urb->number_of_packets.
The length field of urb_priv indicates the number of TDs in the urb.
The td_cnt field indicates the number of TDs already processed by xHC.
When td_cnt matches length, the urb can be given back to usbcore.
When an urb is dequeued or cancelled, add all the unprocessed TDs to the
endpoint's cancelled_td_list. When process a cancelled TD, increase
td_cnt field. When td_cnt equals urb_priv->length, giveback the
cancelled urb.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds mechanism to process Missed Service Error Event.
Sometimes the xHC is unable to process the isoc TDs in time, it will
generate Missed Service Error Event. In this case some TDs on the ring are
not processed and missed. When encounter a Missed Servce Error Event, set
the skip flag of the ep, and process the missed TDs until reach the next
processed TD, then clear the skip flag.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds new cases to trb_comp_code switch, and moves
the switch judgment ahead of fetching td.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the bulk and interrupt td processing part in
handle_tx_event() into a separate function process_bulk_intr_td().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the ctrl td processing part in handle_tx_event()
into a separate function process_ctrl_td().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the td universal processing part in handle_tx_event()
into a separate function finish_td().
if finish_td() returns 1, it indicates the urb can be given back.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds Huawei ETS 1220 product id into the list of supported
devices in 'option' usb serial driver.
Signed-off-by: Pavel Kazlou <p.i.kazlou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Logitech Harmony 700 series needs an extra delay during
initialization. This patch adds a USB quirk which enables such a delay
and adds the device to the quirks list.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enlarging the buffer size via the MON_IOCT_RING_SIZE ioctl causes
general protection faults. It appears the culprit is an incorrect
argument to mon_free_buff: instead of passing the size of the current
buffer being freed, the size of the new buffer is passed.
Use the correct size argument to mon_free_buff when changing the size of
the buffer.
Signed-off-by: Steven Robertson <steven@strobe.cc>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed entry referencing g_eth_ffs.c file from Makefile.
The file never existed and the line was a leftover from a
developing process.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1409) removes some dead code from the ehci-hcd
scheduler. Thanks to the previous patch in this series, stream->depth
is no longer used. And stream->start and stream->rescheduled
apparently have not been used for quite a while, except in some
statistics-reporting code that never gets invoked.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1408) rearranges the scheduling code in ehci-hcd, partly
to improve its structure, but mainly to change the way it works.
Whether or not a transfer exceeds the hardware schedule length will
now be determined by looking at the last frame the transfer would use,
instead of the first available frame following the end of the transfer.
The benefit of this change is that it allows the driver to accept
valid URBs which would otherwise be rejected. For example, suppose
the schedule length is 1024 frames, the endpoint period is 256 frames,
and a four-packet URB is submitted. The four transfers would occupy
slots that are 0, 256, 512, and 768 frames past the current frame
(plus an extra slop factor). These don't exceed the 1024-frame limit,
so the URB should be accepted. But the current code notices that the
next available slot would be 1024 frames (plus slop) in the future,
which is beyond the limit, and so the URB is rejected unnecessarily.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1407) fixes a bug in ehci-hcd's isochronous scheduler.
All its calculations should be done in terms of microframes, but for
full-speed devices, sched->span is stored in frames. It needs to be
converted.
This fix is liable to expose problems in other drivers. The old code
would accept URBs that should not have been accepted, so drivers have
had no reason to avoid submitting URBs that exceeded the maximum
schedule length. In an attempt to partially compensate for this, the
patch also adjusts the schedule length from a minimum of 256 frames up
to a minimum of 512 frames.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1406) adds a micro-optimization to ehci-hcd's scheduling
code. Instead of computing remainders with respect to the schedule
length, use bitwise-and (which is quicker). We know that the schedule
length will always be a power of two, but the compiler doesn't have
this information.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1405) fixes a small bug in ehci-hcd's isochronous
scheduler. Not all EHCI controllers are PCI, and the code shouldn't
assume that they are. Instead, introduce a special flag for
controllers which need to delay iso scheduling for full-speed devices
beyond the scheduling threshold.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: David Brownell <david-b@pacbell.net>
CC: stable <stable@kernel.org>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Enable MSI/MSI-X supporting in xhci driver.
Provide the mechanism to fall back using MSI and Legacy IRQs
if MSI-X IRQs register failed.
Signed-off-by: Dong Nguyen <Dong.Nguyen@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>,
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1) Introduce ulpi specific flags for control of the ulpi phy
2) Extend the generic ulpi driver with support for Function and
Interface control of upli phy
3) Update the platforms using the generic ulpi driver with new ulpi
flags
4) Remove the otg control flags not in use
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ulpi_set_vbus and ulpi_set_flags are using ULPI_SET(register) to write
to the PHY's registers, which means we can only set bits in the PHY's
register and not clear them.
By directly using the address of the register without any offset, we
now get the expected behaviour for these functions.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONFIG_ARCH_KARO doesn't exist in Kconfig and is never defined anywhere
else, therefore removing all references for it from the source code.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Usb serial port device is child of its usb interface device, so
we can enable async suspend of usb serial port device to speedup
system suspend.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch for the musb usb controller.
It allows forwarding of the debug mode feature to its gadget in order
to be able to act as an ehci debug device.
This patch has been tested on an IGEPv2 board running a 2.6.35-rc1
kernel.
Signed-off-by: Stephane Duverger <stephane.duverger@gmail.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch that implements an USB EHCI Debug Device using the
Gadget API. This patch applies to a 2.6.35-rc3 kernel.
The gadget needs a compliant usb controller that forwards the
USB_DEVICE_DEBUG_MODE feature to its gadget.
The gadget provides two configuration modes, one that only printk() the
received data, and one that exposes a serial device to userland
(/dev/ttyGSxxx).
The gadget has been tested on an IGEPv2 board running a 2.6.35-rc1
kernel. The debug port was fed on the host side by a 2.6.34 kernel.
Signed-off-by: Stephane Duverger <stephane.duverger@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed several coding style issues in freecom.c.
Signed-off-by: Martin Enderleit <menderleit@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
