MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It turns out that v4's firmware provides a command so we can query
the resolution. Let's use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Starting with v3 hardware, the firmware supports this shorter
elantech_send_cmd. Teach the driver to use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This converts the drivers in drivers/input/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.
Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Henk Vergonet <Henk.Vergonet@gmail.com>
Cc: Alessandro Rubini <rubini@ipvvis.unipv.it>
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: "Magnus Hörlin" <magnus@alefors.se>
Cc: Chris Moeller <kode54@gmail.c>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Edwin van Vliet <edwin@cheatah.nl>
Cc: Ping Cheng <pingc@wacom.com>
Cc: Eduard Hasenleithner <eduard@hasenleithner.at>
Cc: Alexander Strakh <strakh@ispras.ru>
Cc: Glenn Sommer <gsommer@datanordisk.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PM methods are basically the same for SPI and I2C busses, so let's
use the same dev_pm_ops for both of them.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the EETI eGalax serial multi touch controller driver.
EETI eGalax serial touch screen controller is a I2C based multiple
capacitive touch screen controller, it can support 5 touch events maximum.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We have determined that the jumpiness previously seen when using
the synaptics kernel mouse driver on OLPC XO was due to not using
the synaptics X11 userspace driver - the xf86-input-evdev driver was
interpreting 'finger near pad' signals as movements. Newer versions
of xf86-input-evdev fix this issue.
Additionally, the synaptics kernel driver is now usable on this
platform, but only when run in relative mode.
Update the comment and refine the check to allow the synaptics driver
to run on OLPC XO in relative mode.
We will continue investigating the EC issue as time becomes available.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is nothing in keypad platform definitions that requires
the driver be complied on Samsung platform only, so let's move them
out of the platform subdirectory and relax the dependencies.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, the synaptics driver puts the device into Absolute mode.
As explained in the synaptics documentation section 3.2, in this mode,
the device sends a continuous stream of packets at the maximum rate
to the host when the user's fingers are near or on the pad or
pressing buttons, and continues streaming for 1 second afterwards.
These packets are even sent when there is no new information to report,
even when they are duplicates of the previous packet.
For embedded systems this is a bit much - it results in a huge
and uninterrupted stream of interrupts at high rate.
This patch adds support for Relative mode, which can be selected as
a new psmouse protocol. In this mode, the device does not send duplicate
packets and acts like a standard PS/2 mouse. However, synaptics-specific
functionality is still available, such as the ability to set the packet
rate, and rather than disabling gestures and taps at the hardware level
unconditionally, a 'synaptics_disable_gesture' sysfs attribute has
been added to allow control of this functionality.
This solves a long standing OLPC issue: synaptics hardware enables
tap to click by default (even in the default relative mode), but we
have found this to be inappropriate for young children and first
time computer users. Enabling the synaptics driver disables tap-to-click,
but we have previously been unable to use this because it also enables
Absolute mode, which is too "spammy" for our desires and actually
overloads our EC with its continuous stream of packets. Now we can enable
the synaptics driver, disabling tap to click while retaining the less
noisy Relative mode.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With commit 67d0a07544 we mark strict_strtox
as obsolete. Convert all remaining such uses in drivers/input/.
Also change long to appropriate types, and return error conditions
from kstrtox separately, as Dmitry sugguests.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix the following compilation failure with v3.2-rc1 by including module.h:
CC drivers/input/serio/ams_delta_serio.o
drivers/input/serio/ams_delta_serio.c:33:15: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c:34:20: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c:35:16: error: expected declaration specifiers or '...' before string constant
drivers/input/serio/ams_delta_serio.c: In function 'ams_delta_serio_init':
drivers/input/serio/ams_delta_serio.c:155:2: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/input/serio/ams_delta_serio.c:155:2: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes some v3 hardware (fw_version: 0x150500) wrongly detected
as v2 hardware.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Tested-By: Marc Dietrich <marvin24@gmx.de>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for two ALPS touchpad protocols not
supported currently by the driver, which I am arbitrarily naming
version 3 and version 4. Support is single-touch only at this time,
although both protocols are capable of limited multitouch support.
Thanks to Andrew Skalski, who did the initial reverse-engineering
of the v3 protocol.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for version 4 protocol support, which has 8-byte
data packets, remove all hard-coded assumptions about packet size
and use psmouse->pktsize instead.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for adding support for more ALPS protocol versions,
add a field for the protocol version to the model info instead of
using a field in the flags. OLDPROTO and !OLDPROTO are now called
version 1 and version 2, repsectively.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for new protocol support, move the protocol
information currently documented in alps.c to
Documentation/input/alps.txt, where it can be expanded without
cluttering up the driver.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo's Pen and Touch packets always start with a value
of 0x02 in first byte. In 3rd gen Bamboo's, the hw is now
periodically sending some additional packets with unrelated data
and uses a value other than 0x02 to inform driver this.
Ignore those packets now.
This was reported by users as bad behavior in Gimp. The
invalid packets being processed made the stylus report
out of proximity for the 1 packet and this triggered some
secondary bug which caused Gimp to stop drawing until
user really took pen out of proximity of tablet.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Touchpad input doesn't work with newer HP Pavilion dv4 laptops due to bad i8042
timeout data. Booting with i8042.notimeout and i8042.nomux successfully works
around the problem.
This patch adds the devices to the i8042 notimeout and nomux blacklists.
Signed-off-by: Tomas Miljenovic <TomasM@tomasm.tk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In addition to some laptops needing i8042 reset after resuming from S2R to
get their touchpads working there is another class of laptops - ones that
need i8042 reset before going to S2R, otherwise they will simply reboot
instead of resuming.
See https://bugzilla.kernel.org/show_bug.cgi?id=15612
This change forces reset of i8042 before doing S2R.
Reported-by: Stefan Koch <stefan_koch@gmx.net>
Tested-by: Alexander van Loon <a.vanloon@alexandervanloon.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
These files are not modules but are exporting symbols and/or
making use of THIS_MODULE macro.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in input dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (348 commits)
[media] pctv452e: Remove bogus code
[media] adv7175: Make use of media bus pixel codes
[media] media: vb2: fix incorrect return value
[media] em28xx: implement VIDIOC_ENUM_FRAMESIZES
[media] cx23885: Stop the risc video fifo before reconfiguring it
[media] cx23885: Avoid incorrect error handling and reporting
[media] cx23885: Avoid stopping the risc engine during buffer timeout
[media] cx23885: Removed a spurious function cx23885_set_scale()
[media] cx23885: v4l2 api compliance, set the audioset field correctly
[media] cx23885: hook the audio selection functions into the main driver
[media] cx23885: add generic functions for dealing with audio input selection
[media] cx23885: fixes related to maximum number of inputs and range checking
[media] cx23885: Initial support for the MPX-885 mini-card
[media] cx25840: Ensure AUDIO6 and AUDIO7 trigger line-in baseband use
[media] cx23885: Enable audio line in support from the back panel
[media] cx23885: Allow the audio mux config to be specified on a per input basis
[media] cx25840: Enable support for non-tuner LR1/LR2 audio inputs
[media] cx23885: Name an internal i2c part and declare a bitfield by name
[media] cx23885: Ensure VBI buffers timeout quickly - bugfix for vbi hangs during streaming
[media] cx23885: remove channel dump diagnostics when a vbi buffer times out
...
Fix up trivial conflicts in drivers/misc/altera-stapl/altera.c (header
file rename vs add)
This driver has been tested with hardware and works as expected. To use
it add the platform data as appropriate and register it with the
corresponding I2C bus.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (68 commits)
Input: adp5589-keys - add support for the ADP5585 derivatives
Input: imx_keypad - add pm suspend and resume support
Input: force feedback - potential integer wrap in input_ff_create()
Input: tsc2007 - make sure that X plate resistance is specified
Input: serio_raw - fix memory leak when closing char device
Input: serio_raw - kick clients when disconnecting port
Input: serio_raw - explicitly mark disconnected ports as dead
Input: serio_raw - fix coding style issues
Input: serio_raw - use dev_*() for messages
Input: serio_raw - use bool for boolean data
Input: serio_raw - perform proper locking when adding clients to list
Input: serio_raw - rename serio_raw_list to serio_raw_client
Input: serio_raw - use kref instead of rolling out its own refcounting
Input: psmouse - switch to using dev_*() for messages
Input: wacom - correct max Y value on medium bamboos
Input: wacom - add ABS_DISTANCE to Bamboo Pen reports
Input: wacom - remove unneeded touch pressure initialization
Input: lm8323 - wrap suspend and resume in CONFIG_PM_SLEEP
Input: ad7879-i2c - wrap suspend and resume in CONFIG_PM_SLEEP
Input: synaptics_i2c - wrap suspend and resume in CONFIG_PM_SLEEP
...
3rd generation Bamboo Pen and Touch tablets reuse the older
stylus packet but add an extra fixed zero pad byte to end.
The touch packets are quite different since it supports tracking
of up to 16 touches. The packet is 64-byte fixed size but contains
up to 15 smaller messages indicating data for a single touch or
for tablet button presses.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Override invalid pen based pktlen and x/y_max with touch
values from HID report.
Since active area of pen and touch are same on these
devices, set physical x/y size while pen x/y_max and
resolution are still valid.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bit 0x02 always means tip versus eraser. Bit 0x01 is something related
to version of stylus and different values are starting to be used.
Relaxing proximity check is required to be used with 3rd generation
Bamboo Pen and Touch tablets.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo's do not declared a Digitizer-Stylus so the if() was
never executed. wacom_features already contains correct stylus
packet length.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Only the stylus interface on Bamboo's has a feature report that can
be used to set to wacom mode. The touch interface only has 1 report mode
and will return errors for those get/sets requests.
The get request was always erroring out because it was not marked as
an input request. Only down side of error was needlessly resending the
set request 5 times.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
This adds support for the power-on buttons of MC13783 PMIC.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the first step to also support the touch interface of the mc13892
pmic chip.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The ADP5585 family keypad decoder and IO expander is similar to the ADP5589,
however it features less IO pins, and lacks hardware assisted key-lock
functionality. Unfortunately the register addresses are different, as well as
the event codes and bit organization within the port related registers.
Move ADP5589 Register defines from the header file into the main source file.
Add new defines while making sure we don't break existing platform_data.
Add register address translation, and turn device specific defines into variables.
Introduce some helper functions and disable functions that doesn't
exist on the added devices.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The imx_keypad driver was indicating that it was wakeup capable in
imx_keypad_probe(), but it didn't implement suspend or resume methods.
According to the i.MX series MCU Reference Manual, the kpp (keypad
port) is a major wake up source which can detect any key press even
in low power mode and even when there is no clock.
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The problem here is that max_effects can wrap on 32 bits systems.
We'd allocate a smaller amount of data than sizeof(struct ff_device).
The call to kcalloc() on the next line would fail but it would write
the NULL return outside of the memory we just allocated causing data
corruption.
The call path is that uinput_setup_device() get ->ff_effects_max from
the user and sets the value in the ->private_data struct. From there
it is:
-> uinput_ioctl_handler()
-> uinput_create_device()
-> input_ff_create(dev, udev->ff_effects_max);
I've also changed ff_effects_max so it's an unsigned int instead of
a signed int as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The VIBSELL/R bit in the VIBCTLL/R register tells the source of the data,
which is going to be used to drive the attached motor(s).
Do not allow effect execution if any of the channels are set to receive
audio data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bits within the two control registers (for left and right channel)
are identical.
Use common names for the bits acros the two register.
Also add the missing definition for the path selection bit.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Abort driver initialization if X plate resistance was not specified in
platform data as it will cause pressure to be always calculated as 0,
and making userspace ignore touch coordinates.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently we never freed memory allocated when users open our char
devices nor removed old users from the list of connected clients.
Also unregister misc device immediately upon disconnecting the port
instead of waiting until last user drops off (refcounting in misc
device code will make sure needed pieces stay around while they
are needed) and make sure we are not holing holding serio_raw_mutex
when registering/unregistering misc device. This should fix potential
deadlock between serio_raw and misc device code uncovered by lockdep
and reported by Thomas Tuttle.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Send SIGIO/POLL_HUP and otherwise wake up waiters when corresponding serio
port is being disconnected. Also check if port is dead in serio_raw_poll
and signal POLLHUP|POLLERR.
This should speed up process of releasing dead devices by userspace
applications.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of relying on setting serio_raw->serio to NULL upon disconnecting
ports mark them explicitly as "dead". Also take and carry reference to
underlying serio port to make sure it does not go away until we are done
with it.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will ensure our reporting is consistent with the rest of the system.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make sure we hold serio lock when adding clients to client list so that
we do not race with serio_raw_release() removing clients from the same
list.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
'serio_raw_list' and 'list' names do not accurately represent their objects
and are extremely confusing when reading the code. Let's use better suited
names.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will ensure our reporting is consistent with the rest of the system
and we do not refer to obsolete source file names.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: JJ Ding <dgdunix@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Medium size Bamboo P&T driver reused max X/Y form older Bamboo 1
medium size tablets and never updated to real value. Actual
active area of tablet is slightly larger in Y direction.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tablet reports a distance of 0 right at highest point possible
to be in proximity and distance_max when touching tablet. Inverse
the distance since user land has no way of knowing ABS_DISTANCE
is not distance from tablet.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These were left in during removal of touch pressure reports but not
needed now.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
lm8323.c: warning: 'lm8323_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
ad7879-i2c.c: warning: 'ad7879_i2c_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
synaptics_i2c.c: warning: 'synaptics_i2c_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes GCC is not smart enough to recognize that x, y and z are
always used properly initialized in mma8450_poll(). Let's rearrange
the code a bit to help GCC.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysfs attribute show methods are always passed a buffer of length
PAGE_SIZE. To keep from overwriting this buffer and causing havoc, use
snprintf() to guarantee we never write more than the buffer can hold.
In addition, at least for my touchscreen, the number and size of objects
was far too big to fit in a single 4K page. Therefore, this patch also
trims some redundant framing text to leave more room for actual data.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cintiq 21ux2 has two sets of four LEDs on right and left side of
the tablet, respectively.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The LED also indicates the status of the tablet. Don't turn it off.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The LED luminance level is normally lower when no button is pressed.
Reviewed-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Tested-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts commit 71c86ce597.
The 21UX2 does have touchstrips, but they are in a somewhat-
hidden location.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the TSC-40 serial touchscreen driver and should be
compatible with TSC-10 and TSC-25.
The driver was written by Linutronix on behalf of Bachmann electronic GmbH.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver will be migrated to the RC driver API in a following
commit.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the of_property_read_u32() helper function to retrieve u32 values
from the device tree. Also do not pass the len parameter to
of_get_property if it isn't checked afterwards.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since touchscreen driver does not handle any events to be sent to the
device we can close serio port first and then unregister the input device.
Tested-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of having one large switch based on product ID use pointer to
function actually doing protocol decoding.
Tested-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add multi touch support for PenMount 6250 touch controller.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MSB and LSB of the XY axis value are switched according to the PenMount 9000 protocol. The driver name is also changed from penmountlpc, since it is not for LPC interface at all.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This essentially reverts commit f81bc788ff.
With recent work on elantech driver, I believe we now have complete support
for all elantech touchpads. So remove this hack.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
V2 hardware has many variants. This patch adddresses two issues:
- some model also has debounce packets, but with a different signature
than v3. Now we just check debounce for all v2 hardware.
- due to different scanning methods the hardware uses, x and y ranges have
to be calculated differently. And for some specific versions, we can just
see them as custom-made, so set {x, y} the same values as Windows driver
does.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Tested-by: Richard Schütz <r.schtz@t-online.de>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboos with Product ID's > 0xD4 return values unrelated to pressure
in touch 1 pressure field. They also report 2nd touch X/Y values
shifted down 1 byte (where pressure was). This results in jumpy
1 finger touch and totally invalid 2nd finger data.
For touch detection, switch to a Touch Present single bit that
all versions of Bamboo support.
For touch 2 offset, calculate offset based on a bit that is set
different between the two packet layouts.
Since touch pressure reports were removed from driver, there was
no need to be reading pressure any more.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds trackpad support for the MacBookAir4,1, released in July 2011.
It is very similar to the MacBookAir4,2 patch submitted by Joshua Dillon and
Chase Douglas.
Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
v4 hardware is a true multitouch capable touchpad (up to 5 fingers).
The packet format is quite complex, please see protocol document for
reference.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
v3 hardware's packet format is almost identical to v2 (one/three finger touch),
except when sensing two finger touch, the hardware sends 12 bytes of data.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For v2 hardware, there is no real parity check, but we can still check
some constant bits for data integrity.
Also rename elantech_check_parity_v1 to elantech_packet_check_v1 to make
these packet checking function names consistent.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Don't try to be too clever and remove ETP_EDGE_FUZZ_V2. X, Y ranges
should be just the raw resolution of the device. Otherwise, they can
cause underflow on the Y axis.
Suggested-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With newer hardware, the touchpad provides range info.
Let's use it.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For two finger touches the coordinate of each finger gets reported
separately but with reduced resolution.
With this change, we now have the same range for ST and MT data and
scale MT data because it has lower resolution to match ST.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Acked-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix warning from Geert's build summary emails by changing "if" to
"ifdef". Thsi should fix the following:
drivers/input/misc/twl6040-vibra.c:231:5: warning: "CONFIG_PM_SLEEP" is not defined
Builds cleanly with CONFIG_PM_SLEEP enabled or disabled.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Take spinlock when entering ISR and timer routine to ensure that we do not
race while enabling/disabling FIFO interrupts.
Also we do not need to take teh spinlock in tegra_kbc_startremove() since
interrupt is completely disabled.
Tested-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For wakeup to be reliable, kbc needs to be in interrupt mode before suspend.
Created common routine to control the FIFO interrupt.
Added synchronization to ensure orderly suspend.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
WARNING: drivers/input/keyboard/built-in.o(.text+0xb55b): Section mismatch in reference from the function tc3589x_keypad_open() to the function .devinit.text:tc3589x_keypad_init_key_hardware()
The function tc3589x_keypad_open() references
the function __devinit tc3589x_keypad_init_key_hardware().
This is often because tc3589x_keypad_open lacks a __devinit
annotation or the annotation of tc3589x_keypad_init_key_hardware is wrong.
Signed-off-by: Harvey Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adds INPUT_PROP_POINTER or INPUT_PROP_DIRECT as necessary to the
hardware supported by the Wacom driver. The DIRECT property is
assigned to devices with an embedded screen (i.e. touchscreens
and display tablets). The POINTER property is assigned to those
without embedded screens.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This commit enables control of the LEDs and OLED displays found on the
Wacom Intuos4 M, L, and XL. For this purpose, a new "wacom_led" attribute
group is added to the sysfs entry of the USB device.
This "wacom_led" group only shows up when the correct device (M, L, or XL)
is detected. The attributes are described in
Documentation/ABI/testing/sysfs-wacom
Signed-off-by: Eduard Hasenleithner <eduard@hasenleithner.at>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For i2c drivers, we should use "i2c:" prefix for modalias.
MODULE_DEVICE_TABLE will setup the modulalias for us, thus adding
a MODULE_ALIAS is redundant (in addition to being incorrect).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will ensure that the device delivers input events only when there
are users.
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of using hard IRQ and workqueue solution switch to using threaded
interrupt handler to simplify the code and locking rules.
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If successful, usb_control_msg returns the number of bytes transferred,
otherwise a negative error number.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Wacom PenPartner should advertise its stylus tip and button
in addition to the eraser tool. These are both physically
present on the hardware, and emitted from 'wacom_penpartner_irq'.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad714x - read the interrupt status registers in a row
Input: ad714x - use DMA-safe buffers for spi_write()
Input: ad714x - fix endianness issues
Input: ad714xx-spi - force SPI bus into the default 8-bit mode
Input: ep93xx_keypad - add missing include of linux/module.h
Input: tnetv107x-ts - add missing include of linux/module.h
Input: max11801_ts - correct license statement
Input: atmel_mxt_ts - report pressure information from the driver
Input: bcm5974 - Add support for newer MacBookPro8,2
Input: wacom - report id 3 returns 4 bytes of data
Input: wacom - add WAC_MSG_RETRIES define
Input: wacom - add support for the Wacom Bamboo Pen (CTL-660/K)
Input: tegra-kbc - correct call to input_free_device
Input: mpu3050 - correct call to input_free_device
Input: bcm5974 - add support for touchpads found in MacBookAir4,2
Input: mma8450 - fix module device table type
Input: remove CLOCK_TICK_RATE from analog joystick driver
Change the placement of __init and __exit annotations to be consistent
with the rest of the drivers.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics image sensor touchpads track up to 5 fingers, but only report 2.
They use a special "TYPE=2" (AGM-CONTACT) packet type that reports
the number of tracked fingers and which finger is reported in the SGM
and AGM packets.
With this new packet type, it is possible to tell userspace when 4 or 5
fingers are touching.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
"4-finger scroll" is a gesture supported by some applications and
operating systems.
"Resting thumb" is when a clickpad user rests a finger (e.g., a
thumb), in a "click zone" (typically the bottom of the touchpad) in
anticipation of click+move=select gestures.
Thus, "4-finger scroll + resting thumb" is a 5-finger gesture.
To allow userspace to detect this gesture, we send BTN_TOOL_QUINTTAP.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics image sensor touchpads track 5 fingers, but only report 2.
This patch attempts to deal with some idiosyncrasies of these touchpads:
* When there are 3 or more fingers, only two are reported.
* The touchpad tracks the 5 fingers in slot[0] through slot[4].
* It always reports the lowest and highest valid slots in SGM and AGM
packets, respectively.
* The number of fingers is only reported in the SGM packet. However,
the number of fingers can change either before or after an AGM
packet.
* Thus, if an SGM reports a different number of fingers than the last
SGM, it is impossible to tell whether the intervening AGM corresponds
to the old number of fingers or the new number of fingers.
* For example, when going from 2->3 fingers, it is not possible to tell
whether tell AGM contains slot[1] (old 2nd finger) or slot[2] (new
3rd finger).
* When fingers are added one at at time, from 1->2->3, it is possible to
track which slots are contained in the SGM and AGM packets:
1 finger: SGM = slot[0], no AGM
2 fingers: SGM = slot[0], AGM = slot[1]
3 fingers: SGM = slot[0], AGM = slot[2]
* It is also possible to track which slot is contained in the SGM when 1
of 2 fingers is removed. This is because the touchpad sends a special
(0,0,0) AGM packet whenever all fingers are removed except slot[0]:
Last AGM == (0,0,0): SGM contains slot[1]
Else: SGM contains slot[0]
* However, once there are 3 fingers, if exactly 1 finger is removed, it
is impossible to tell which 2 slots are contained in SGM and AGM.
The (SGM,AGM) could be (0,1), (0,2), or (1,2). There is no way to know.
* Similarly, if two fingers are simultaneously removed (3->1), then it
is only possible to know if SGM still contains slot[0].
* Since it is not possible to reliably track which slot is being
reported, we invalidate the tracking_id every time the number of
fingers changes until this ambiguity is resolved when:
a) All fingers are removed.
b) 4 or 5 fingers are touched, generates an AGM-CONTACT packet.
c) All fingers are removed except slot[0]. In this special case, the
ambiguity is resolved since by the (0,0,0) AGM packet.
Behavior of the driver:
When 2 or more fingers are present on the touchpad, the kernel reports
up to two MT-B slots containing the position data for two of the fingers
reported by the touchpad. If the identity of a finger cannot be tracked
when the number-of-fingers changes, the corresponding MT-B slot will be
invalidated (track_id set to -1), and a new track_id will be assigned in
a subsequent input event report.
The driver always reports the total number of fingers using one of the
EV_KEY/BTN_TOOL_*TAP events. This could differ from the number of valid
MT-B slots for two reasons:
a) There are more than 2 fingers on the pad.
b) During ambiguous number-of-fingers transitions, the correct track_id
for one or both of the slots cannot be determined, so the slots are
invalidated.
Thus, this is a hybrid singletouch/MT-B scheme. Userspace can detect
this behavior by noting that the driver supports more EV_KEY/BTN_TOOL_*TAP
events than its maximum EV_ABS/ABS_MT_SLOT.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A Synaptics image sensor tracks 5 fingers, but can only report 2.
The algorithm for choosing which 2 fingers to report and in which packet:
Touchpad maintains 5 slots, numbered 0 to 4
Initially all slots are empty
As new fingers are detected, assign them to the lowest available slots
The touchpad always reports:
SGM: lowest numbered non-empty slot
AGM: highest numbered non-empty slot, if there is one
In addition, these touchpads have a special AGM packet type which reports
the number of fingers currently being tracked, and which finger is in
each of the two slots. Unfortunately, these "TYPE=2" packets are only used
when more than 3 fingers are being tracked. When less than 4 fingers
are present, the 'w' value must be used to track how many fingers are
present, and knowing which fingers are being reported is much more
difficult, if not impossible.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics makes (at least) two kinds of touchpad sensors:
* Older pads use a profile sensor that could only infer the location
of individual fingers based on the projection of their profiles
onto row and column sensors.
* Newer pads use an image sensor that can track true finger position
using a two-dimensional sensor grid.
Both sensor types support an "Advanced Gesture Mode":
When multiple fingers are detected, the touchpad sends alternating
"Advanced Gesture Mode" (AGM) and "Simple Gesture Mode" (SGM)
packets.
The AGM packets have w=2, and contain reduced resolution finger data
The SGM packets have w={0,1} and contain full resolution finger data
Profile sensors try to report the "upper" (larger y value) finger in
the SGM packet, and the lower (smaller y value) in the AGM packet.
However, due to the nature of the profile sensor, they easily get
confused when fingers cross, and can start reporting the x-coordinate
of one with the y-coordinate of the other. Thus, for profile
sensors, "semi-mt" was created, which reports a "bounding box"
created by pairing min and max coordinates of the two pairs of
reported fingers.
Image sensors can report the actual coordinates of two of the fingers
present. This patch detects if the touchpad is an image sensor and
reports finger data using the MT-B protocol.
NOTE: This patch only adds partial support for 2-finger gestures.
The proper interpretation of the slot contents when more than
two fingers are present is left to later patches. Also,
handling of 'number of fingers' transitions is incomplete.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When a Synaptics touchpad is in "AGM" mode, and multiple fingers are
detected, the touchpad sends alternating "Advanced Gesture Mode" (AGM) and
"Simple Gesture Mode" (SGM) packets.
The AGM packets have w=2, and contain reduced resolution finger data.
The SGM packets have w={0,1} and contain full resolution finger data.
Refactor the parsing of agm packets to its own function, and rename the
synaptics_data.mt field to .agm to indicate that it contains the contents of
the last agm packet.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics touchpads report increasing y from bottom to top.
This is inverted from normal userspace "top of screen is 0" coordinates.
Thus, the kernel driver reports inverted y coordinates to userspace.
This patch refactors this inversion.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since touchscreen driver does not handle any events to be sent to the
device we can close serio port first and then unregister the input device.
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Implement open() and close() methods for the input device so that we
do not start the device unless there are users listening to the events.
Acked-by: Chris Bagwell <chris@cnpbagwell.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The interrupt status registers should be read in row to avoid invalid data.
Alter "read" method for both bus options to allow reading several registers
in a row and make sure we read interrupt status registers properly.
Read sequence saves 50% of bus transactions compared to single register
reads. So use it also for the result registers, which are also located
in a row.
Also update copyright notice.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
spi_write() requires use of DMA-safe (cacheline aligned) buffers.
Also use the same buffers when reading data since to avoid extra
locking and potential memory allocation in spi_write_then_read().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow driver to be used on Big Endian boxes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ep93xx_keypad.c uses interfaces from linux/module.h,
so it should include that file. This patch fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
tnetv107x-ts.c uses interfaces from linux/module.h,
so it should include that file. This patch fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The original license statement was confusing since it was unclear if
the license was pure GPLv2 or GPLv2+ and did not match the license
of the driver max11801_ts was derived from. The license is GPLv2+.
Signed-off-by: Jiejing Zhang <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Atmel mxt1386 touch controller has the touch pressure information so
let's report it to the user space.
[dtor@mail.ru: added ABS_RESSURE reporting for ST emulation.]
Signed-off-by: Yufeng Shen <miletus@chromium.org>
Acked-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New MacBook Pro devices reporting product name MacBookPro8,2 come with
newer/higher resolution touchpads than others with the same product
name with USB ID 05ac:0252. This patch adds support for these devices.
Signed-off-by: Andrew Drake <adrake@adrake.org>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If kzalloc for kbc fails, then we have NULL pointer dereference while
calling input_free_device(kbc->idev) in the error handling.
So it is safer to always use the original name, input_dev.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
input_free_device() should be used if input_register_device() was not called
yet or if it failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Albert Zhang <xu.zhang@bosch-sensortec.com>
Signed-off-by: Eric Andersson <eric.andersson@unixphere.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
To allow open/ioctl(EVIOCGABS)/close use pattern for polled devices read
the device in context of open() call instead of offloading the first read
to a workqueue. This will ensure that once call to open() returns device
would have cached reasonably recent axis values that can be retrieved via
appropriate ioctl.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Added USB device IDs for MacBookAir4,2 trackpad. Device constants were
copied from the MacBookAir3,2 constants. The 4,2 device specification is
reportedly unchanged from the 3,2 predecessor and seems to work well.
Signed-off-by: Joshua V Dillon <jvdillon@gmail.com>
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The module device table for of_device_id should use "of" type.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The analog joystick driver is written for x86 systems. This
patch updates it to use the PIT_TICK_RATE value instead of
CLOCK_TICK_RATE as they are equivalent on x86 and we want to
deprecate the latter.
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Input close or device disable should not interact with the exported
gpiolib functionality. However that's the case. __ad7879_disable()
clears the entire AD7879_REG_CTRL2, while it should just power down
the ADC and its reference.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add missing header.
Error log:
CC drivers/input/serio/xilinx_ps2.o
drivers/input/serio/xilinx_ps2.c: In function 'xps2_of_probe':
drivers/input/serio/xilinx_ps2.c:249: error: implicit declaration of function 'of_address_to_resource'
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It adds device tree probe support for mma8450 driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Eric Miao <eric.miao@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add missing device_remove_file() for dev_attr_time in lm8323_remove().
Also calling device_remove_file() in lm8323_probe() error path to
remove sysfs attribute file.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix a constant definition and computation of polling time.
[dtor@mail.ru: switched to using DIV_ROUND_UP as was suggested by
Thierry Reding <thierry.reding@avionic-design.de>]
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to explicitly include module.h since some of its facilities
are used.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
hgpk.c uses interfaces from linux/module.h, so it should include that file.
This fixes build errors.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
Input: synaptics - fix reporting of min coordinates
Input: tegra-kbc - enable key autorepeat
Input: kxtj9 - fix locking typo in kxtj9_set_poll()
Input: kxtj9 - fix bug in probe()
Input: intel-mid-touch - remove pointless checking for variable 'found'
Input: hp_sdc - staticize hp_sdc_kicker()
Input: pmic8xxx-keypad - fix a leak of the IRQ during init failure
Input: cy8ctmg110_ts - set reset_pin and irq_pin from platform data
Input: cy8ctmg110_ts - constify i2c_device_id table
Input: cy8ctmg110_ts - fix checking return value of i2c_master_send
Input: lifebook - make dmi callback functions return 1
Input: atkbd - make dmi callback functions return 1
Input: gpio_keys - switch to using SIMPLE_DEV_PM_OPS
Input: gpio_keys - add support for device-tree platform data
Input: aiptek - remove double define
Input: synaptics - set minimum coordinates as reported by firmware
Input: synaptics - process button bits in AGM packets
Input: synaptics - rename set_slot to be more descriptive
Input: synaptics - fuzz position for touchpad with reduced filtering
Input: synaptics - set resolution for MT_POSITION_X/Y axes
...
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
We were testing wrong bit in the extended capability query.
Reported-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
To support key repeats, keyboard needs to be setup as an autorepeating
device.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
According to the comments we want to call mutex_lock() here instead
of mutex_unlock(). That makes more sense.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We are testing the wrong variable here. I believe tj9->input_dev
is always NULL at this point, so probe() will fail.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The implementation does break from the for loop after we assign 'i' to
variable 'found'.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It's not referenced outside this file so there's no need for it to be in
the global name space.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make sure we are passing the same cookie in all calls to
request_any_context_irq() and free_irq().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The implementation in cy8ctmg110_probe() does not properly set reset_pin
and irq_pin from platform data. Let's fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
i2c_master_send returns negative errno, or else the number of bytes written.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We only care about if there is a successful match from the table (or
no match at all), so let's make dmi_check_system return immediately
instead of iterating thorough the whole table.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We only care about if there is a successful match from the table (or
no match at all), so let's make dmi_check_system return immediately
instead of iterating thorough the whole table.
Make the dmi callback function return 1 then dmi_check_system
will return immediately if we have a successful match.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables fetching configuration data, which is normally provided
via platform_data, from the device-tree instead.
If the device is configured from device-tree data, the platform_data struct
is not used, and button data needs to be allocated dynamically. Big part of
this patch deals with confining pdata usage to the probe function, to make
this possible.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Newer Synaptics firmware allows to query minimum coordinates reported by
the device, let's use this data.
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The twl6040_request_irq/free_irq inline functions are going
to be removed, so replace them with direct calls.
The irq number is provided by the core driver via resource.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
AGM packets contain valid button bits, too.
This patch refactors packet processing to parse button bits in AGM packets.
However, they aren't actually used or reported.
The point is to more completely process AGM packets,
and prepare for future patches that may actually use AGM packet button bits.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics touchpads indicate via a capability bit when they perform reduced
filtering on position data. In such a case, use a non-zero fuzz value.
Fuzz = 8 was chosen empirically by observing the raw position data
reported by a clickpad indicating it had reduced filtering.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Set resolution for MT_POSITION_X and MT_POSITION_Y to match ABS_X and
ABS_Y, respectively.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The old code may call input_sync() without sending any other events.
While it will be suppressed by the input core not calling it at all
is still cheaper.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bamboo touch sets BTN_BACK, BTN_FORWARD, BTN_LEFT, and BTN_RIGHT
as the default button events for tablet buttons. Change Graphire4
and old Bamboo to the same settings.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With the removal of BTN_TOOL_FINGER for tablet buttons and
expresskeys, serial number is needed to distingush if the
events were from a regular tool (stylus, eraser, or mouse)
or the attribures (buttons, strips, or wheels) on the tablet
since there are overlapped events between the tools and the
tablet attributes.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
BTN_TOOL_FINGER was designed to indicate a single finger touch.
Remove the lines that borrowed this type for expresskeys and
tablet buttons.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, battery drivers also use poll_sample() provided by the
wm97xx-core but this code always checks if the pen is down. Mark the
channels which really need this (i.e. for the touchscreen) with the
PEN_DOWN bit, and skip the checks otherwise. Now, the battery channels
can always be read.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The current implementation of poll_sample() has the problem that one of
its arguments, the channel to be selected, differs from wm9713 to other
variants. This parameter gets passed to the (currently unused)
mach-specific functions pre_sample() and post_sample() which thus have
to deal with codec-specific differences. Refactor the routine so that
the argument to poll_sample() is generic for all codecs and do necessary
conversions only in the codec-specific driver. The outcome even uses
less code and removes the non-standard use of the PEN_DOWN bit to mark
the AUX-channels.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch implements rumble support for XBox360 Wireless Controllers.
Signed-off-by: Chris Moeller <kode54@gmail.c>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allign the platform data names for twl4030 audio submodule:
twl4030_audio_data: for the core MFD driver
twl4030_codec_data: for ASoC codec driver
twl4030_vibra_data: for the input/ForceFeedback driver
To avoid breakage, change all depending drivers, files
to use the new types.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Rename the driver, and header file from twl4030-codec to
twl4030-audio.
To avoid breakage change depending drivers at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
The "#if" above should really be an "#ifdef" to avoid this warning:
CC drivers/input/keyboard/sh_keysc.o
drivers/input/keyboard/sh_keysc.c:294:5: warning: "CONFIG_PM_SLEEP" is
not defined
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
