Commit Graph

157053 Commits

Author SHA1 Message Date
Chaithrika U S
1a7ff8ff6e davinci: audio: move tlv320aic33 i2c setup into board files
Tested on DM6446, DM355, DM6447, DA850 EVMs.

Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:56:31 +03:00
Sandeep Paulraj
213765d7b4 DaVinci: EDMA: Adding 2 new APIs for allocating/freeing PARAMs
For best performance, codecs often setup linked triggered
transfers with a contiguous block of params, and that is when
this API is used. Setup/configuration of these parameter RAMs
is most efficient if they are contiguous.
There is an API to allocate a set of contiguous parameter RAMs and
a corresponding API to free a set of contiguous parameter RAMs

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:59 +03:00
Sandeep Paulraj
0c30e0d31b DaVinci: DM365: Adding entries for DM365 IRQ's
This patch adds definitions for some DM365 IRQs that are used by
the codecs. Codecs will also use the IRQs.
Entries are being added to enable/disable IRQ's.
There is no use as such for these entires in the kernel itself.
Instead these will be used by the "linuxutils" package of the DVSDK.

For further information on IRQ muxing refer to
http://focus.ti.com/lit/ug/sprufg5a/sprufg5a.pdf

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:58 +03:00
Sandeep Paulraj
1aebb50e06 DaVinci: DM355: Adding PINMUX entries for DM355 Display
This patch adds PINMUX entries for DM355 Display.
These will be used by the DM355 display driver.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:57 +03:00
Sudhakar Rajashekhara
820c4fe32e davinci: Handle pinmux conflict between mmc/sd and nor flash
On DA850/OMAP-L138 EVM, MMC/SD and NOR Flash share
some of the AEMIF pins. This patch prints out a warning
during booting, if both MMC/SD and NOR Flash are enabled
in kernel menuconfig.

If both MMC/SD and NOR Flash are enabled, only MMC/SD
will work correctly.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:57 +03:00
Sudhakar Rajashekhara
7c5ec6095a davinci: Add NOR flash support for da850/omap-l138
This patch adds platform data for the 8MB NOR flash
found on da850/omap-l138 EVM. Both NOR and NAND can
co-exist on da850/omap-l138 as they are using different
chip selects.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:56 +03:00
Sudhakar Rajashekhara
38beb929f2 davinci: Add NAND flash support for DA850/OMAP-L138
This patch adds platform data for the 512MB NAND Flash
found on DA850/OMAP-L138 EVM. Currently it supports
only 1-bit ECC.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:56 +03:00
Sudhakar Rajashekhara
700691f27e davinci: Add MMC/SD support for da850/omap-l138
There are two instances of MMC/SD on da850/omap-l138.
Connector for the first instance is available on the
EVM. This patch adds support for this instance.

This patch also adds support for card detect and write
protect switches on da850/omap-l138 EVM.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:55 +03:00
Sudhakar Rajashekhara
5cbdf276bd davinci: Add platform support for da850/omap-l138 GLCD
This patch adds platform support for the graphic display
(Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:54 +03:00
Sudhakar Rajashekhara
b1466376b2 davinci: Macro to convert GPIO signal to GPIO pin number
Adds a macro to convert the GPIO signal passed as bank number
and signal to GPIO pin number.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:54 +03:00
Chaithrika U S
491214e1f8 davinci: Audio support for DA850/OMAP-L138 EVM
Define resources for McASP used on DA850/OMAP-L138 EVM, add platform
device defintion and Pin Mux configurations.

Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:53 +03:00
Chaithrika U S
e33ef5e3b3 davinci: Audio support for DA830 EVM
Define resources for McASP1 used on DA830/OMAP-L137 EVM, add platform
device defintion, initialization function.  Additionally, this patch
also adds version and FIFO related members to platform data structure.

Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:52 +03:00
Sudhakar Rajashekhara
5a8d5441f4 davinci: Correct the number of GPIO pins for da850/omap-l138
DA850/OMAP-L138 has 144 pins configurable as GPIO, but
currently this has been configured as 128. This patch
corrects it.

Also, this patch adds the base address for GPIO pins
greater than 128.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:52 +03:00
Sudhakar Rajashekhara
53ca5c9169 davinci: Configure MDIO pins for EMAC
Earlier patch which adds EMAC support for da850/omap-l138
was not configuring the MDIO pins.

Ethernet was working fine with the earlier patch, because
the MDIO pins were configured from the boot loader. This
patch removes that dependency.

Also, this patch populates a member in the emac clk structure
to say that EMAC LPSC sits on controller 1.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:51 +03:00
Sandeep Paulraj
cc36e97b0b DaVinci: DM365: Add Support for new Revision of silicon
DM365 RBL has been updated. The variant number has changed for this
new revision of silicon. This patch adds support for the
new revision of DM365.
The name fields are also being updated to reflect the version
of the silicon.

Without this minor fix DM365 REV 1.2 will not boot up

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:50 +03:00
Sandeep Paulraj
866d286953 DaVinci: DM365: Fix Compilation issue due to PINMUX entry
The mask can hold only 8 bit values. This gave a
compilation warning. This patch rectifies the warning.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:50 +03:00
Sandeep Paulraj
a0f0202e2a DaVinci: EDMA: Updating default queue handling
EDMA queues in DM365 are a little different than those
on other DaVinci's. On DM365 Q0 and Q1 have the larger
FIFO size. We want Q0 and Q1 to be used by codecs and
DVSDK demos.
MMC driver is the only driver which uses the flag
'EVENTQ_DEFAULT'. So MMC driver should be using Q2 instead of
Q1 on DM365.
This patch allows us to declare a "default queue" from
SOC specific code. If it is not declared then the EDMA
driver assumes a default of queue 1.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:49 +03:00
Sandeep Paulraj
10eef5a8a0 DaVinci: EDMA: Add queue 2 and 3 for DM365 and DM6467
DM365 and DM6467 have 4 queues. The patch updates the
'dma_event_q' enum to reflect this.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:48 +03:00
Kevin Hilman
889c1e0dab davinci: Kconfig: add dm646x ASoC support 2009-08-26 11:55:48 +03:00
Kevin Hilman
61aa07328d davinci: audio clocks: use struct device instead of clock names
There is no need to pass clock name strings in platform_data.
Instead, setup clkdev nodes to have correct ASoC device names.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:47 +03:00
Hemant Pedanekar
548197bdf0 davinci: dm646x-evm: Add support for IDE
Controls ATA_RSTn and ATA_PWD through CPLD register 0 to enable ATA. An I2C
driver is added for the same. Calls ide init if enabled in configuration.

Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:47 +03:00
Kevin Hilman
10a1af384e davinci: Kconfig: update default defconfig
Updated default defconfig after da850 merge and 2.6.31-rc3 update.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:46 +03:00
Sudhakar Rajashekhara
5a4b131508 davinci: Add EMAC support for da850/omap-l138
Ethernet Media Access Controller (EMAC) on da850/omap-l138
supports 10/100 Mbps operation. It also supports Media
Independent Interface (MII) and Reduced Media Independent
Interface (RMII) to physical layer (PHY).

Phy which supports MII is present on the DA850/OMAP-L138
base board and Phy supporting RMII is present on the
UI card. This patch adds support only for the MII Phy.
Support for RMII Phy will be added later.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:45 +03:00
Sudhakar Rajashekhara
0fbc559215 davinci: Add support for DA850/OMAP-L138 EVM board
Add support for the DA850/OMAP-L138 Evaluation Module (EVM)
from TI.  The EVM has User Interface (UI) card which contains
various devices. This UI card can be connected to the base
board. Support for all the devices on the UI card and ones on
the EVM will be added in subsequent patches.

The EVM schematics are not available publicly yet; but should
be available soon.

A new defconfig for this board has been added mainly because
the DA830/OMAP-L137 defconfig forces writethrough cache mode
which is not required on DA850/OMAP-L138.

This patch has been boot tested on DA850/OMAP-L138 EVM
using ramdisk as filesystem.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:45 +03:00
Sudhakar Rajashekhara
e1a8d7e2ea davinci: Add base DA850/OMAP-L138 SoC support
The DA850/OMAP-L138 is a new SoC from TI in the same family as
DA830/OMAP-L137.

Major changes include better support for power management,
support for SATA devices and McBSP (same IP as DM644x).

DA850/OMAP-L138 documents are available at
http://focus.ti.com/docs/prod/folders/print/omap-l138.html.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:44 +03:00
Sergei Shtylyov
efd911814e davinci: DM646x: pass correct MUSB IRQs
DM646x has MUSB connected to IRQs 13 and 14 (unlike IRQ12 on other platforms),
so pass the correct IRQ resources with the platform device.

Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 11:55:38 +03:00
Sudhakar Rajashekhara
c96b56c53f davinci: Rearrange the da830/omap-l137 macros and functions
Rearrange the PINMUX macros and pinmux_setup function which
are common between da830/omap-l137 and da850/omap-l138.

Also, replace the da830 string in function names to da8xx.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:02 +03:00
Sudhakar Rajashekhara
2259bbd460 davinci: Pass proper EDMA CC interrupt number for DA830/OMAP-L137
In EDMA resource structure, instead of passing EDMA CC
interrupt, EDMA TC error interrupt number is being passed.

Before the patch:
	root@arago:~# cat /proc/interrupts
	           CPU0
	 12:          0     cp_intc  edma_error
	 13:          0     cp_intc  edma
	Err:

After the patch:
	root@arago:~# cat /proc/interrupts
	           CPU0
	 11:          0     cp_intc  edma
	 12:          0     cp_intc  edma_error
	Err:

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:02 +03:00
Rajashekhara, Sudhakar
bea238f65c davinci: Move the da830/omap-l137 #defines to header file
With the introduction of TI da850/omap-l138, some of the macros
defined for da830/omap-l137 will be needed in da850 source file.
So, move the common macros to da8xx.h header file.

Also, modify the macro names from DA830_... to DA8XX_.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:02 +03:00
Hemant Pedanekar
1c92a554fc davinci: dm646x: Add IDE setup
This patch adds platform data and init function for IDE which could be called
from board specific file to register IDE device.

Note that for 594MHz device the transfer mode is limited to UDMA4 since ideclk
rate is less than 100 MHz, which forces udma_mask in palm_bk3710.c to UDMA4,
while for 729MHz device, it is UDMA5.

Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:02 +03:00
Sekhar Nori
6077d26532 davinci: make arch_idle and arch_reset as inline functions
Make arch_idle and arch_reset inline as inline function.

Not having them inline leads to a warning of this sort when only
one of these functions is used:

arch/arm/mach-davinci/include/mach/system.h:24: warning: 'arch_reset' \
defined but not used

boot, re-boot tested on OMAP-L138 EVM

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:01 +03:00
Kevin Hilman
baf09a4cd0 davinci: da830: updates for mach-type name change
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:01 +03:00
Hemant Pedanekar
9eb7115bcc davinci: Move IO device mapping macros from io.h to hardware.h
This patch takes out IO mapping macros from mach/io.h and puts them in
mach/hardware.h avoiding need to include mach/io.h in various files such as
serial.h, vmalloc.h etc.

The main reason to avoid inclusion of mach/io.h is, when default in/out macros
are overridden by machine specific functions (e.g., in case of PCI I/O), they
result into linker error. An example snippet and error snapshot is listed below.

Following code in mach/io.h:

	#define inl(p)  my_inl()

	static inline unsigned int my_inl(unsigned int addr)
	{
		if (IS_PCI_IO(addr))
			return pci_inl ();
		else
			return le32_to_cpu(__raw_readl(__typesafe_io(addr)));
	}

leads to error:
	LD      arch/arm/boot/compressed/vmlinux
	arch/arm/boot/compressed/misc.o: In function `my_inl':
	misc.c:(.text+0x2744): undefined reference to `pci_inl'
	make[2]: *** [arch/arm/boot/compressed/vmlinux] Error 1

This is because mach/io.h gets included in arch/arm/boot/compressed/misc.c
through mach/serial.h but pci.c file, which defines 'pci_inl' doesn't get built
into compressed vmlinux.

Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:01 +03:00
Hemant Pedanekar
3e25d5f4fd davinci: dm646x: Add clock info and update mux setup for ATA
This patch adds clock data for IDE and also updates pin mux mask for ATA so as
to disable PCI when ATA is selected.

Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:01 +03:00
Kevin Hilman
88659988d5 davinci: Kconfig: update default config for 2.6.31-rc
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:00 +03:00
Chaithrika U S
25acf553ae davinci: ASoC: Add the platform devices for ASP
1) Registers the platform devices for ASP on dm355, dm644x and dm646x
   so that the machine driver can probe to get ASP related platform
   data.
2) Move towards definition of the asp clocks using physical name(for
   dm355 and dm644x)
3) Add platform data to board specific files.

Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:00 +03:00
David Brownell
7a36071e79 davinci: dm365 gpio irq support
Support DM365 GPIOs ... primarily by handling non-banked GPIO IRQs:

 - Flag DM365 chips as using non-banked GPIO interrupts, using a
   new soc_info field.

 - Replace the gpio_to_irq() mapping logic.  This now uses some
   runtime infrastructure, keyed off that new soc_info field,
   which doesn't handle irq_to_gpio().

 - Provide a new irq_chip ... GPIO IRQs handled directly by AINTC
   still need edge triggering managed by the GPIO controller.

DM365 chips no longer falsely report 104 GPIO IRQs as they boot.

Intelligence about IRQ muxing is missing, so for the moment this
only exposes the first eight DM365 GPIOs, which are never muxed.
The next eight are muxed, half with Ethernet (which uses most of
those pins anyway).

Tested on DM355 (10 unbanked IRQs _or_ 104 banked ones) and also
on DM365 (16 unbanked ones, only 8 made available).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:00 +03:00
Sandeep Paulraj
af5dbaef76 davinci: DM365 Updating PINMUX Entries
Patch updates DM365 PINMUX by adding entries for Video, SPI 1 - 4,
PWM 0 - 3.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:57:00 +03:00
Mark A. Greer
8593790d60 davinci: da8xx: Add support for DA830/OMAP-L137 EVM board
Add support for the DA830/OMAP-L137 Evaluation Module (EVM)
from TI.  The EVM has User Interface (UI) and Audio cards
that can be connected which contain various devices.
Support for those devices and ones on the EVM will be
added in subsequent patches.

Additional generalizations for future SoCs in da8xx family done by
Sudhakar Rajashekhara and Sekhar Nori.

Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:59 +03:00
Mark A. Greer
55c79a40e3 davinci: da8xx: Add base DA830/OMAP-L137 SoC support
The da830/omap l137 is a new SoC from TI that is similar
to the davinci line.  Since its so similar to davinci,
put the support for the da830 in the same directory as
the davinci code.

There are differences, however.  Some of those differences
prevent support for davinci and da830 platforms to work
in the same kernel binary.  Those differences are:

1) Different physical address for RAM.  This is relevant
   to Makefile.boot addresses and PHYS_OFFSET.  The
   Makefile.boot issue isn't truly a kernel issue but
   it means u-boot won't work with a uImage including
   both architectures.  The PHYS_OFFSET issue is
   addressed by the "Allow for runtime-determined
   PHYS_OFFSET" patch by Lennert Buytenhek but it
   hasn't been accepted yet.

2) Different uart addresses.  This is only an issue
   for the 'addruart' assembly macro when CONFIG_DEBUG_LL
   is enabled.  Since the code in that macro is called
   so early (e.g., by _error_p in kernel/head.S when
   the processor lookup fails), we can't determine what
   platform the kernel is running on at runtime to use
   the correct uart address.

These areas have compile errors intentionally inserted
to indicate to the builder they're doing something wrong.

A new config variable, CONFIG_ARCH_DAVINCI_DMx, is added
to distinguish between a true davinci architecture and
the da830 architecture.

Note that the da830 currently has an issue with writeback
data cache so CONFIG_CPU_DCACHE_WRITETHROUGH should be
enabled when building a da830 kernel.

Additional generalizations for future SoCs in the da8xx family done by
Sudhakar Rajashekhara and Sekhar Nori.

Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:59 +03:00
David Brownell
ff255c6caa davinci: dm365 evm cpld support: leds, card detect, other setup
Add basic support for the CPLD on the DM365 EVM board:

 - Read SW5 to set up NAND and keypad vs (someday) OneNAND
 - Export MMC/SD card detect and writeprotect signals
 - LED support (same layout as on DM355 EVM)
 - Static config for video input:
     * external HD imager precludes MMC1, Ethernet, audio
     * else either tvp5146 (SD/default) or tvp7002 (HD)

The video input could actually be switched around dynamically;
change that if/when that's needed (and after those other video
inputs have driver support).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:59 +03:00
Sandeep Paulraj
37b798da5d davinci: dm365: add NAND support to EVM board
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:59 +03:00
Sandeep Paulraj
a45c8ba30b davinci: MMC/SD Support for dm365 EVM
Patch adds support for MMC/SD in the DM365 EVM.
Pinmux for MMC/SD slot 1 on the DM365 EVM is also
configured.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:59 +03:00
Sandeep Paulraj
19ff3bf2e8 davinci: dm365: add MMC/SD support
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:58 +03:00
Sandeep Paulraj
15061b5d02 davinci: dm365: add EDMA support
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:58 +03:00
Sandeep Paulraj
8ed0a9d4e7 davinci: dm365: EMAC support for SoC and dm365 EVM
The patch adds Support for EMAC in the DM365 SOC and
the DM365 EVM board.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:58 +03:00
Sandeep Paulraj
9f51315383 davinci: dm365: add mux entries for EDMA, RTC, EMAC, keypad.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:58 +03:00
Sandeep Paulraj
a46e9e403c davinci: Adding DM365 entries to Makefile/Kconfig/defconfig
This patch does the following
1) Adds entries to davinci_all_defconfig for DM365
2) Adds entries to the Makefile for DM365
3) Adds entries for DM365 in the Kconfig

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:58 +03:00
Sandeep Paulraj
37dd009563 davinci: Adding DM365 EVM board support
The patch adds support for Evaluation Module (EVM) board for the dm365
SoC.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:57 +03:00
Sandeep Paulraj
fb8fcb8913 davinci: Adding DM365 SOC Support
The patch adds base support for new TI SOC DM365, which s
similar to the dm355.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-08-26 10:56:57 +03:00