Fix kconfig warnings:
PTP_1588_CLOCK selects NET_PTP_CLASSIFY, which depends on NET,
so PTP_1588_CLOCK should also depend on NET.
PTP_1588_CLOCK_PCH selects PTP_1588_CLOCK so the former should
depend on NET.
warning: (IXP4XX_ETH && PTP_1588_CLOCK) selects NET_PTP_CLASSIFY which has unmet direct dependencies (NET)
warning: (SFC && TILE_NET && BFIN_MAC_USE_HWSTAMP && TIGON3 && FEC && E1000E && IGB && IXGBE && I40E && MLX4_EN && SXGBE_ETH && STMMAC_ETH && TI_CPTS && PTP_1588_CLOCK_GIANFAR && PTP_1588_CLOCK_IXP46X && DP83640_PHY && PTP_1588_CLOCK_PCH) selects PTP_1588_CLOCK which has unmet direct dependencies (NET)
[This warning is caused by the new 'depends on NET' in PTP_1588_CLOCK.]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-05-08
This one is all from Johannes:
"Here are a few small fixes for the current cycle: radiotap TX flags were
wrong (fix by Bob), Chun-Yeow fixes an SMPS issue with mesh interfaces,
Eliad fixes a locking bug and a cfg80211 state problem and finally
Henning sent me a fix for IBSS rate information."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the cas_lock_tx function we acquire multiple locks in a loop and
need to use nested lock annotation to prevent lockdep warnings.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91ebb928b "bnx2x: Add support for Multi-Function UNDI" contains a bug
which prevent the emptying of the device's Rx buffers before reset.
As a result, on new boards it is likely HW will reach some fatal assertion
once its interfaces load after UNDI was previously loaded.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold says:
====================
net: cpsw and mdio-gpio fixes for v3.15-final
These patches against v3.15-rc4 fix a few issues in the cpsw and
mdio-gpio drivers.
Resend with proper stable CC (git send-email still fails to parse the
Sorry about the noise.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix null-pointer dereference at probe when the mdio platform device is
missing (e.g. when it has been disabled in DT).
Cc: stable <stable@vger.kernel.org> # v3.8
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f8d56d8f89 ("net:
eth: cpsw: Correctly attach to GPIO bitbang MDIO driver").
Fix potential null-pointer dereference at probe if the mdio-gpio device
has not been successfully probed yet.
The offending commit is plain wrong for a number of reasons. First of
all it accesses internal driver data of an unrelated device. Neither
does it check that the data is non-null (which it is in case the device
has not been probed yet).
Furthermore, the decision on whether to treat any driver data according
to the mdio-gpio driver's internals is made based on the node name. But
the name is not compared against "mdio" which is the normal name for the
node, but rather against "gpio" which the node does not have to be named
(and shouldn't be according to the binding documentation). [ If this
hack is to be kept out-of-tree it should at least be matching against
the compatible property. ]
Cc: Stefan Roese <sr@denx.de>
Cc: stable <stable@vger.kernel.org> # v3.14
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a sane default bus id (rather than -ENODEV) and print a warning when
the bus alias id is missing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix aliases syntax in device-tree binding example to avoid
copy-paste errors (the alias would be dropped silently).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver maps 802.1q VLANs to MBIM sessions. The mapping is based on
a bogus assumption that all tagged frames will use the acceleration API
because we enable NETIF_F_HW_VLAN_CTAG_TX. This fails for e.g. frames
tagged in userspace using packet sockets. Such frames will erroneously
be considered as untagged and silently dropped based on not being IP.
Fix by falling back to looking into the ethernet header for a tag if no
accelerated tag was found.
Fixes: a82c7ce5bc ("net: cdc_ncm: map MBIM IPS SessionID to VLAN ID")
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following batch contains netfilter fixes for your net tree, they are:
1) Fix use after free in nfnetlink when sending a batch for some
unsupported subsystem, from Denys Fedoryshchenko.
2) Skip autoload of the nat module if no binding is specified via
ctnetlink, from Florian Westphal.
3) Set local_df after netfilter defragmentation to avoid a bogus ICMP
fragmentation needed in the forwarding path, also from Florian.
4) Fix potential user after free in ip6_route_me_harder() when returning
the error code to the upper layers, from Sergey Popovich.
5) Skip possible bogus ICMP time exceeded emitted from the router (not
valid according to RFC) if conntrack zones are used, from Vasily Averin.
6) Fix fragment handling when nf_defrag_ipv4 is loaded but nf_conntrack
is not present, also from Vasily.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver adds support for EtherCAT master module located on CCAT
FPGA found on Beckhoff CX series industrial PCs. The driver exposes
EtherCAT master as an ethernet interface.
EtherCAT is a fieldbus protocol defined on top of ethernet and Beckhoff
CX5020 PCs come with built-in EtherCAT master module located on a FPGA,
which in turn is connected to a PCI bus.
Signed-off-by: Dariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly, when CONFIG_SYSCTL is not set, ping_group_range should still
work, just that no one can change it. Therefore we should move it out of
sysctl_net_ipv4.c. And, it should not share the same seqlock with
ip_local_port_range.
BTW, rename it to ->ping_group_range instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_SYSCTL is not set, ip_local_port_range should still work,
just that no one can change it. Therefore we should move it out of sysctl_inet.c.
Also, rename it to ->ip_local_ports instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dst is released one line before we access it again with dst->error.
Fixes: 58e35d1471 netfilter: ipv6: propagate routing errors from
ip6_route_me_harder()
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If CONFIG_OF is not set, make of_mdiobus_register() call
mdiobus_register() instead of returning -ENOSYS.
This way, we can just call of_mdiobus_register() from all DT-enabled
drivers to handle the compat cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increment fib_info_cnt in fib_create_info() right after successfuly
alllocating fib_info structure, overwise fib_metrics allocation failure
leads to fib_info_cnt incorrectly decremented in free_fib_info(), called
on error path from fib_create_info().
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia says:
====================
qlcnic: Bug fixes.
This patch series contain following bug fixes.
* Fix panic where driver was accessing un-initialized crb_intr_mask
in non Multi-Tx queue mode while dumping TX queue.
* Do not set netdev->real_num_tx_queues directly from driver instead
use kernel defined netif_set_real_num_tx_queues() API. Also notify
stack about change in number of Rx queues.
Please apply this series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set netdev->real_num_tx_queues directly,
let netif_set_real_num_tx_queues() take care of it.
Do not overwrite netdev->num_tx_queues everytime when driver
changes its Tx ring size through ethtool -L and also notify
stack to update number of Rx queues.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In case of non-multi TX queue mode driver does not initialize "crb_intr_mask" pointer
and driver was accessing that un-initialized pointer while dumping TX queue.
So dump "crb_intr_mask" only when it is initilaized.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The jme driver forgot to check the return status from pci_map_page in its tx
path, causing a dma api warning on unmap. Easy fix, just do the check and
augment the tx path to tell the stack that the driver is busy so we re-queue the
frame.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
net: ip: push gso skb forwarding handling down the stack
Turns out doing the segmentation in forwarding was not a bright idea,
there are corner-cases where this has unintended side-effects.
This patch pushes the segmentation downwards.
After this, netif_skb_dev_features() function can be removed
again, it was only added to fetch the features of the output device,
we can just use skb->dev after the pushdown.
Tested with following setup:
host -> kvm_router -> kvm_host
mtu 1500 mtu1280
- 'host' has route to kvm_host with locked mtu of 1500
- gso/gro enabled on all interfaces
Did tests with all of following combinations:
- netfilter conntrack off and on on kvm_router
- virtio-net and e1000 driver on kvm_router
- tcp and udp bulk xmit from host to kvm_host
for tcp, I added TCPMSS mangling on kvm_host to make it lie about tcp mss.
Also added a dummy '-t mangle -A POSTROUTING -p udp -f'
rule to make sure no udp fragments are seen in the 'conntrack on'
and 'virtio-net' case.
Also checked (with ping -M do -s 1400)' that it still sends the wanted
icmp error message when size exceeds 1280.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d206940319,
there are no more callers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing the segmentation in the forward path has one major drawback:
When using virtio, we may process gso udp packets coming
from host network stack. In that case, netfilter POSTROUTING
will see one packet with udp header followed by multiple ip
fragments.
Delay the segmentation and do it after POSTROUTING invocation
to avoid this.
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If conntrack defragments incoming ipv6 frags it stores largest original
frag size in ip6cb and sets ->local_df.
We must thus first test the largest original frag size vs. mtu, and not
vice versa.
Without this patch PKTTOOBIG is still generated in ip6_fragment() later
in the stack, but
1) IPSTATS_MIB_INTOOBIGERRORS won't increment
2) packet did (needlessly) traverse netfilter postrouting hook.
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
local_df means 'ignore DF bit if set', so if its set we're
allowed to perform ip fragmentation.
This wasn't noticed earlier because the output path also drops such skbs
(and emits needed icmp error) and because netfilter ip defrag did not
set local_df until couple of days ago.
Only difference is that DF-packets-larger-than MTU now discarded
earlier (f.e. we avoid pointless netfilter postrouting trip).
While at it, drop the repeated test ip_exceeds_mtu, checking it once
is enough...
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
Yasevich.
2) ns_capable() check in sock_diag netlink code, from Andrew
Lutomirski.
3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.
4) Checksum offloading busted in sxgbe driver due to incorrect
descriptor layout, fix from Byungho An.
5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
Lim.
6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
Starovoitov.
7) Fix arch dependencies of candence driver.
8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.
9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
IFLA_EXT_MASK, from David Gibson.
10) IPV6 FIB dump restart doesn't handle table changes that happen
meanwhile, causing the code to loop forever or emit dups, fix from
Kumar Sandararajan.
11) Memory leak on VF removal in bnx2x, from Yuval Mintz.
12) Bug fixes for new Altera TSE driver from Vince Bridgers.
13) Fix route lookup key in SCTP, from Xugeng Zhang.
14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
driver. From Oliver Hartkopp.
15) TCP doesn't bump retransmit counters in some code paths, fix from
Eric Dumazet.
16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
zero. Fix from Liu Yu.
17) Fix locking imbalance in error paths of HHF packet scheduler, from
John Fastabend.
18) Properly reference the transport module when vsock_core_init() runs,
from Andy King.
19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.
20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
ip_tunnel_rcv(), fix from Ying Cai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
net: macb: Fix race between HW and driver
net: macb: Remove 'unlikely' optimization
net: macb: Re-enable RX interrupt only when RX is done
net: macb: Clear interrupt flags
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
e1000e: Fix issue with link flap on 82579
e1000e: Expand workaround for 10Mb HD throughput bug
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
net/mlx4_core: Load the Eth driver first
net/mlx4_core: Fix slave id computation for single port VF
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
net: cdc_ncm: fix buffer overflow
Altera TSE: ALTERA_TSE should depend on HAS_DMA
vsock: Make transport the proto owner
net: sched: lock imbalance in hhf qdisc
net: mvmdio: Check for a valid interrupt instead of an error
net phy: Check for aneg completion before setting state to PHY_RUNNING
...
Here are some small fixes and device ids for 3.15-rc4.
All have been in linux-next just fine.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNoAMYACgkQMUfUDdst+ymm5QCgzEdgN+YTpuivw63Z/r4ZHGJW
u/QAoLxnz5vjXk9bZDGfnUMEWHrw98Lu
=epx3
-----END PGP SIGNATURE-----
Merge tag 'usb-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small fixes and device ids for 3.15-rc4.
All have been in linux-next just fine"
* tag 'usb-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Nokia 5300 should be treated as unusual dev
USB: Nokia 305 should be treated as unusual dev
fsl-usb: do not test for PHY_CLK_VALID bit on controller version 1.6
usb: storage: shuttle_usbat: fix discs being detected twice
usb: qcserial: add a number of Dell devices
USB: OHCI: fix problem with global suspend on ATI controllers
usb: gadget: at91-udc: fix irq and iomem resource retrieval
usb: phy: fsm: change "|" to "||" for condition OTG_STATE_A_WAIT_BCON at statemachine
usb: phy: fsm: update OTG HNP state transition
Here are some tty and serial driver fixes for things reported recently.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNn/10ACgkQMUfUDdst+ynKXgCg1BE7sLm2Nmxkm+nfYceWmRG2
pQAAnRnY2wBwtpVa4mVy1ZR3ykiKPvmY
=42O2
-----END PGP SIGNATURE-----
Merge tag 'tty-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for things reported
recently"
* tag 'tty-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix lockless tty buffer race
Revert "tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
drivers/tty/hvc: don't free hvc_console_setup after init
n_tty: Fix n_tty_write crash when echoing in raw mode
tty: serial: 8250_core.c Bug fix for Exar chips.
Here are some small IIO driver fixes for 3.15-rc4 that resolve some
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNn+48ACgkQMUfUDdst+yn06wCgzKTAHNtiZDir6xddEr4DfkH+
XNsAoLRJAr+w9hdRuA9JcxnQBK1srTvq
=vuRJ
-----END PGP SIGNATURE-----
Merge tag 'staging-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / iio fixes from Greg KH:
"Here are some small IIO driver fixes for 3.15-rc4 that resolve some
reported issues"
* tag 'staging-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: adc: Nothing in ADC should be a bool CONFIG
iio: exynos_adc: use indio_dev->dev structure to handle child nodes
iio:imu:mpu6050: Fixed segfault in Invensens MPU driver due to null dereference
staging:iio:ad2s1200 fix missing parenthesis in a for statment.
Pull Ceph fixes from Sage Weil:
"First, there is a critical fix for the new primary-affinity function
that went into -rc1.
The second batch of patches from Zheng fix a range of problems with
directory fragmentation, readdir, and a few odds and ends for cephfs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: reserve caps for file layout/lock MDS requests
ceph: avoid releasing caps that are being used
ceph: clear directory's completeness when creating file
libceph: fix non-default values check in apply_primary_affinity()
ceph: use fpos_cmp() to compare dentry positions
ceph: check directory's completeness before emitting directory entry
Under "heavy" RX load, the driver cannot handle the descriptors fast
enough. In detail, when a descriptor is consumed, its used flag is
cleared and once the RX budget is consumed all descriptors with a
cleared used flag are prepared to receive more data. Under load though,
the HW may constantly receive more data and use those descriptors with a
cleared used flag before they are actually prepared for next usage.
The head and tail pointers into the RX-ring should always be valid and
we can omit clearing and checking of the used flag.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverage data suggests that the unlikely case of receiving data while
the receive handler is running may not be that unlikely.
Coverage data after running iperf for a while:
91320: 891: work_done = bp->macbgem_ops.mog_rx(bp, budget);
91320: 892: if (work_done < budget) {
2362: 893: napi_complete(napi);
-: 894:
-: 895: /* Packets received while interrupts were disabled */
4724: 896: status = macb_readl(bp, RSR);
2362: 897: if (unlikely(status)) {
762: 898: if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
762: 899: macb_writel(bp, ISR, MACB_BIT(RCOMP));
-: 900: napi_reschedule(napi);
-: 901: } else {
1600: 902: macb_writel(bp, IER, MACB_RX_INT_FLAGS);
-: 903: }
-: 904: }
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When data is received during the driver processing received data the
NAPI is re-scheduled. In that case the RX interrupt should not be
re-enabled.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few interrupt flags were not cleared in the ISR, resulting in a sytem
trapped in the ISR in cases one of those interrupts occurred. Clear all
flags to avoid such situations.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just as commit "net: macb: DMA-unmap full rx-buffer"
(48330e08fa), pass the size that
was used for mapping the memory also to the unmap routine to
avoid warnings from the DMA_API.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip_tunnel_rcv(), set skb->network_header to inner IP header
before IP_ECN_decapsulate().
Without the fix, IP_ECN_decapsulate() takes outer IP header as
inner IP header, possibly causing error messages or packet drops.
Note that this skb_reset_network_header() call was in this spot when
the original feature for checking consistency of ECN bits through
tunnels was added in eccc1bb8d4 ("tunnel: drop packet if ECN present
with not-ECT"). It was only removed from this spot in 3d7b46cd20
("ip_tunnel: push generic protocol handling to ip_tunnel module.").
Fixes: 3d7b46cd20 ("ip_tunnel: push generic protocol handling to ip_tunnel module.")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Ying Cai <ycai@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000e only.
David provides four fixes for e1000e, first is a workaround for a hardware
erratum on 82579 devices which experienced packet loss in gigabit and 100
speeds when interconnect between the PHY and MAC is exiting K1 power saving
state. Second expands the scope of a workaround to include i217 and i218
parts as well to address over aggressive transmit behavior when connecting
at 10Mbs half-duplex. Next is to resolve a reported link flap issue on
82579 parts which was root caused as an interoperability problem between
82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake
mechanism. Lastly, restricts the workaround of putting the PHY into MDIO
slow mode to access the PHY id to relevant parts since this issue has been
fixed on the newer hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts. The issue that necessitated the workaround has been fixed on the
newer hardware.
We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.
To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle. This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.
Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 772d05c51c "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.
This same behavior is seen on i217 and i218 parts as well. This patch expands
the original workaround to encompass these parts.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.
Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.
Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Or Gerlitz says:
====================
This series contains fixes for 3.15-rc, mostly around SRIOV. The patches by Jack,
Matan and myself fix few issues related to mlx4 SRIOV support for RoCE and single
port VFs, and the patch from Eyal eliminates checking PCI caps for VFs which is misleading.
Patches done against the net tree, commit 014f1b2 "net: bonding: Fix format string
mismatch in bond_sysfs.c"
We'd be happy to get Eyal's patch queued in your -stable list for 3.14.y
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Carrying out PCI speed/width checks through pcie_get_minimum_link()
on VFs yield wrong results, so remove them.
Fixes: b912b2f ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth')
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in SRIOV mode, VM that is assigned with a non-provisioned
Ethernet VFs get themselves a random mac when the Eth driver starts. In
this case, if the IB driver startup code that deals with RoCE runs first,
it will use a zero mac as the source mac for the Para-Virtual CM MADs
which is buggy. To handle that, we change the order of loading.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
