The MCI IP is shared among AVR32 and AT91 SOCs.
AT91 has specific bit definitions in the user interface of MCI SD/MMC IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Now tmio_mmc is able to drive the MMC/SD cell in ASIC3.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
In the write recovery routine, the data to get from the card
is allocated from the stack. The DMA mapping documentation says
explicitly stack memory is not mappable by any of the DMA calls.
Change to using kmalloc() to allocate the memory for the result
from the card and then free it once we've finished with the
transaction.
[ Changed to GFP_KERNEL allocation - Pierre Ossman ]
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
If using ADMA, then we should print the ADMA error
and current pointer in sdhci_dumpregs() when any
debug is requested.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This patch fixes the clock setup in tmio_mmc.
* Incorrect divider setting
* Cruft written to the clock registers (seemingly harmless but Not
Good (tm))
It also eliminates some unnecessary ifs and tidies the loop syntax.
Thanks to Philipp Zabel who discovered the divider issue, commenting
"Except for the SDCLK = HCLK (divider bypassed) case, the clock
setting resulted in double the requested frequency.
The smallest possible frequency (f_max/512) is configured with
a divider setting 0x80, not 0x40."
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
ASIC3 can disable the memory, so we need to wait for mfd_cell->enable
to enable the memory before we can map the SD control registers.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Use an IRQF_TRIGGER_ flag in request_irq instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some ASIC3 devices in the wild are connected with the address bus shifted
by one line, so that its 16-bit registers appear 32-bit aligned in host
memory space.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This patch changes the reported error code for the responses
to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved
for non-recoverable host errors, and the responses from
the SD/MMC card may be because of recoverable transmission
errors in the command or in the response. Response codes
in SPI mode are NOT protected by a checksum, so don't trust them.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Added a platform driver which uses the SDHCI core.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The MMC core has now been fixed to not send silly frequencies to the
drivers which means we can remove this workaround.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Changes pxamci.c to use the regulator subsystem. Uses the regulator case
CONFIG_REGULATOR is defined and a matching is regulator is provided, or
falls back to pdata->setpower otherwise. A warning is displayed case
both a valid regulator and pdata is set, and the regulator is used.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because of granularity issues, sometimes we told the hardware to change
to the voltage we were already at. Rework the logic so this doesn't
happen.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
A pointer to mmc_omap_probe which lives in .init.text is passed to the
core via platform_driver_register and so the kernel might oops if probe
is called after the init code is discarded.
As requested by David Brownell platform_driver_probe is used instead of
moving the probe function to .devinit.text. This saves some memory, but
might have the downside that a device being registered after the call to
mmc_omap_init but before the init sections are discarded will not be
bound anymore to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Speedup for slow cards by transfering more data at once.
This patch also reduces the amount of wear-out of the flash
blocks because fewer partial blocks are written.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.
This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/configfs:
configfs: Rework configfs_depend_item() locking and make lockdep happy
configfs: Silence lockdep on mkdir() and rmdir()
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (30 commits)
[S390] wire up sys_perf_counter_open
[S390] wire up sys_rt_tgsigqueueinfo
[S390] ftrace: add system call tracer support
[S390] ftrace: add function graph tracer support
[S390] ftrace: add function trace mcount test support
[S390] ftrace: add dynamic ftrace support
[S390] kprobes: use probe_kernel_write
[S390] maccess: arch specific probe_kernel_write() implementation
[S390] maccess: add weak attribute to probe_kernel_write
[S390] profile_tick called twice
[S390] dasd: forward internal errors to dasd_sleep_on caller
[S390] dasd: sync after async probe
[S390] dasd: check_characteristics cleanup
[S390] dasd: no High Performance FICON in 31-bit mode
[S390] dcssblk: revert devt conversion
[S390] qdio: fix access beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
[S390] vmalloc: add vmalloc kernel parameter support
[S390] uaccess: use might_fault() instead of might_sleep()
[S390] 3270: lock dependency fixes
[S390] 3270: do not register with tty_register_device
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use more NOFS allocation
dlm: connect to nodes earlier
dlm: fix use count with multiple joins
dlm: Make name input parameter of {,dlm_}new_lockspace() const
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Start documenting HAVE_PERF_COUNTERS requirements
perf_counter: Add forward/backward attribute ABI compatibility
perf record: Explicity program a default counter
perf_counter: Remove PERF_TYPE_RAW special casing
perf_counter: PERF_TYPE_HW_CACHE is a hardware counter too
powerpc, perf_counter: Fix performance counter event types
perf_counter/x86: Add a quirk for Atom processors
perf_counter tools: Remove one L1-data alias
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (62 commits)
Blackfin: fix sparseirq/kstat_irqs fallout
Blackfin: fix unused warnings after nommu update
Blackfin: export the last exception cause via debugfs
Blackfin: fix length checking in kgdb_ebin2mem
Blackfin: kgdb: fix up error return values
Blackfin: push access_ok() L1 attribute down
Blackfin: punt duplicated search_exception_table() prototype
Blackfin: add missing access_ok() checks to user functions
Blackfin: convert early_printk EVT init to a loop
Blackfin: document the lsl variants of the L1 allocator
Blackfin: rename Blackfin relocs according to the toolchain
Blackfin: check SIC defines rather than variant names
Blackfin: add SSYNC to set_dma_sg() for descriptor fetching
Blackfin: convert SMP to only use generic time framework
Blackfin: bf548-ezkit/bf537-stamp: add resources for ADXL345/346
Blackfin: override default uClinux MTD addr/size
Blackfin: fix command line corruption with DEBUG_DOUBLEFAULT
Blackfin: fix handling of initial L1 reservation
Blackfin: merge sram init functions
Blackfin: drop unused reserve_pda() function
...
* 'for-linus' of git://linux-arm.org/linux-2.6:
kmemleak: Add more info to the MAINTAINERS entry
kmemleak: Remove the kmemleak.h include in drivers/char/vt.c
git commit 0a0c5168 "PM: Introduce functions for suspending and resuming
device interrupts" introduced some helper functions. However these
functions are only available for architectures which support
GENERIC_HARDIRQS.
Other architectures will see this build error:
drivers/built-in.o: In function `sysdev_suspend':
(.text+0x15138): undefined reference to `check_wakeup_irqs'
drivers/built-in.o: In function `device_power_up':
(.text+0x1cb66): undefined reference to `resume_device_irqs'
drivers/built-in.o: In function `device_power_down':
(.text+0x1cb92): undefined reference to `suspend_device_irqs'
To fix this add some empty inline functions for !GENERIC_HARDIRQS.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The *_nvs_* routines in swsusp.c make use of the io*map()
functions, which are only provided for HAS_IOMEM, thus
breaking compilation if HAS_IOMEM is not set. Fix this
by moving the *_nvs_* routines into hibernate_nvs.c, which
is only compiled if HAS_IOMEM is set.
[rjw: Change the name of the new file to hibernate_nvs.c, add the
license line to the header comment.]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the name of kernel/power/disk.c to kernel/power/hibernate.c
in analogy with the file names introduced by the changes that
separated the suspend to RAM and standby funtionality from the
common PM functions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Move the suspend to RAM and standby code from kernel/power/main.c
to two separate files, kernel/power/suspend.c containing the basic
functions and kernel/power/suspend_test.c containing the automatic
suspend test facility based on the RTC clock alarm.
There are no changes in functionality related to these modifications.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
This patch reworks the platform driver code for legacy
suspend and resume to avoid installing callbacks in
struct device_driver. A warning is also added telling
users to update the platform driver to use dev_pm_ops.
The functions platform_legacy_suspend()/resume() directly
call suspend and resume callbacks in struct platform_driver
instead of wrapping things in platform_drv_suspend()/resume().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch removes the legacy callbacks ->suspend() and
->resume() from struct device_type. These callbacks seem
unused, and new code should instead make use of struct
dev_pm_ops.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
A future patch is going to modify the memory shrinking code so that
it will make memory allocations to free memory instead of using an
artificial memory shrinking mechanism for that. For this purpose it
is convenient to move swsusp_shrink_memory() from
kernel/power/swsusp.c to kernel/power/snapshot.c, because the new
memory-shrinking code is going to use things that are local to
kernel/power/snapshot.c .
[rev. 2: Make some functions static and remove their headers from
kernel/power/power.h]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Remove the shrinking of memory from the suspend-to-RAM code, where
it is not really necessary.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Remove the ->suspend_late() and ->resume_early() callbacks
from struct bus_type V2. These callbacks are legacy stuff
at this point and since there seem to be no in-tree users
we may as well remove them. New users should use dev_pm_ops.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1241) renames a bunch of functions in the PM core.
Rather than go through a boring list of name changes, suffice it to
say that in the end we have a bunch of pairs of functions:
device_resume_noirq dpm_resume_noirq
device_resume dpm_resume
device_complete dpm_complete
device_suspend_noirq dpm_suspend_noirq
device_suspend dpm_suspend
device_prepare dpm_prepare
in which device_X does the X operation on a single device and dpm_X
invokes device_X for all devices in the dpm_list.
In addition, the old dpm_power_up and device_resume_noirq have been
combined into a single function (dpm_resume_noirq).
Lastly, dpm_suspend_start and dpm_resume_end are the renamed versions
of the former top-level device_suspend and device_resume routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rename the functions performing "_noirq" dev_pm_ops
operations from device_power_down() and device_power_up()
to device_suspend_noirq() and device_resume_noirq().
The new function names are chosen to show that the functions
are responsible for calling the _noirq() versions to finalize
the suspend/resume operation. The current function names do
not perform power down/up anymore so the names may be misleading.
Global function renames:
- device_power_down() -> device_suspend_noirq()
- device_power_up() -> device_resume_noirq()
Static function renames:
- suspend_device_noirq() -> __device_suspend_noirq()
- resume_device_noirq() -> __device_resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch removes unused asm/suspend.h files for
the following architectures:
alpha, arm, ia64, m68k, mips, s390, um
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is the last unification step. Here we do remove one of the files
and rename the left one as cpu.c, as both are now the same.
Also update power/Makefile, telling it to build cpu.o, instead of
cpu_(32|64).o
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In this step, we do unify the copyright notes for both files
cpu_32.c and cpu_64.c, making such files exactly the same.
It's the last step before the actual unification, that will
rename one of them to cpu.c and remove the other one.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In this step we do unify cpu_32.c and cpu_64.c functions that
work on restoring the saved processor state. Also, we do
eliminate the forward declaration of fix_processor_context()
for X86_64, as it's not needed anymore.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In this step we do unify cpu_32.c and cpu_64.c functions that
work on saving the processor state.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
