We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add soc node for am4372 with pm-sram phandle to both pm-sram-code and
pm-sram-data regions.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a phandle to point to both the pm-sram-code and pm-sram-data nodes
so that the pm code can locate the sram regions needed to copy low level
PM code.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we will use ti-emif-sram driver for am4372 PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we will use ti-emif-sram driver for am335x PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for RTC on STM32H743 SoC.
It also adds dt-bindings/interrupt-controller/irq.h include and uses it to
configure RTC alarm interrupt.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32h743i-eval in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for USB OTG HS and FS on STM32H743 SoC:
-USB OTG HS controller is the same than the one used on STM32F7 SoCs.
-USB OTG FS controller is the same than the one used on STM32F4 SoCs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32f749-disco in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure USB OTG HS in OTG (DRD) mode on STM32746G_eval.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
USB OTG HS on STM32F746 can also be used as Peripheral (gadget), so
this patch adds DWC2 gadget mode fifo sizes bindings.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add nodes for the four user leds.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The HSE oscillator frequency was wrongly set to 125MHz instead of 25MHz.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds SDIO-related DT nodes required by stm32f469 board
There is a hardware issue on these boards, it misses a pullup on
the GPIO line used as card detect to allow correct SD card
detection. To allow correct card detection "broken-cd" property
is used.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds the pin configuration for SDIO controller on
stm32f4.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since commit 9273083a15 ("usb: dwc2: Fix TxFIFOn sizes and total TxFIFO
size issues") we could use the OTG mode again.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add BCM43438 (bluetooth) as a serdev slave device of uart0 (pl011/ttyAMA0).
This allows to automatically insert the bcm43438 to the bluetooth
subsystem instead of relying on patched userspace helpers (hciattach).
In order to keep a debug UART we need to switch to uart1.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of keeping the firmware's pull settings, we better apply
them via the devicetree pin control. Start with the RPi Zero W relevant
first to keep the effort low.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This stops the driver from trying to probe the ATA slave
interface. The vendor code enables the slave interface
but the driver in the vendor tree does not make use of
it.
Setting it to muxmode 0 disables the slave interface:
the hardware only has the master interface connected
to the one harddrive slot anyways.
Without this change booting takes excessive time, so it
is very annoying to end users.
Fixes: dd5c0561db ("ARM: dts: Add basic devicetree for D-Link DNS-313")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The CONFIG_LIRC symbol has changed from 'tristate' to 'bool, so we now
get a warning for omap2plus_defconfig:
arch/arm/configs/omap2plus_defconfig:322:warning: symbol value 'm' invalid for LIRC
This changes the file to mark the symbol as built-in to get rid of the
warning.
Fixes: a60d64b15c ("media: lirc: lirc interface should not be a raw decoder")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- optimization for the exitless interrupt support that was merged in 4.16-rc1
- improve the branch prediction blocking for nested KVM
- replace some jump tables with switch statements to improve expoline performance
- fixes for multiple epoch facility
ARM:
- fix the interaction of userspace irqchip VMs with in-kernel irqchip VMs
- make sure we can build 32-bit KVM/ARM with gcc-8.
x86:
- fixes for AMD SEV
- fixes for Intel nested VMX, emulated UMIP and a dump_stack() on VM startup
- fixes for async page fault migration
- small optimization to PV TLB flush (new in 4.16-rc1)
- syzkaller fixes
Generic:
- compiler warning fixes
- syzkaller fixes
- more improvements to the kvm_stat tool
Two more small Spectre fixes are going to reach you via Ingo.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEbBAABAgAGBQJakL/fAAoJEL/70l94x66Dzp4H9j6qMzgOTAQ0bYmupQp81tad
V8lNabVSNi0UBYwk2D44oNigtNjQckE18KGnjuJ4tZW+GZ+D7zrrHrKXWtATXgxP
SIfHj+raSd/lgJoy6HLu/N0oT6wS+PdZMYFgSu600Vi618lGKGX1SIAwBhjoxdMX
7QKKAuPcDZ1qgGddhWaLnof28nQQEWcCAVfFeVojmM0TyhvSbgSysh/Gq10ydybh
NVUfgP3fzLtT9gVngX/ZtbogNkltPYmucpI+wT3nWfsgBic783klfWrfpnC/GM85
OeXLVhHwVLG6tXUGhb4ULO+F9HwRGX31+er6iIxmwH9PvqnQMRcQ0Xxf2gbNXg==
=YmH6
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"s390:
- optimization for the exitless interrupt support that was merged in 4.16-rc1
- improve the branch prediction blocking for nested KVM
- replace some jump tables with switch statements to improve expoline performance
- fixes for multiple epoch facility
ARM:
- fix the interaction of userspace irqchip VMs with in-kernel irqchip VMs
- make sure we can build 32-bit KVM/ARM with gcc-8.
x86:
- fixes for AMD SEV
- fixes for Intel nested VMX, emulated UMIP and a dump_stack() on VM startup
- fixes for async page fault migration
- small optimization to PV TLB flush (new in 4.16-rc1)
- syzkaller fixes
Generic:
- compiler warning fixes
- syzkaller fixes
- more improvements to the kvm_stat tool
Two more small Spectre fixes are going to reach you via Ingo"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (40 commits)
KVM: SVM: Fix SEV LAUNCH_SECRET command
KVM: SVM: install RSM intercept
KVM: SVM: no need to call access_ok() in LAUNCH_MEASURE command
include: psp-sev: Capitalize invalid length enum
crypto: ccp: Fix sparse, use plain integer as NULL pointer
KVM: X86: Avoid traversing all the cpus for pv tlb flush when steal time is disabled
x86/kvm: Make parse_no_xxx __init for kvm
KVM: x86: fix backward migration with async_PF
kvm: fix warning for non-x86 builds
kvm: fix warning for CONFIG_HAVE_KVM_EVENTFD builds
tools/kvm_stat: print 'Total' line for multiple events only
tools/kvm_stat: group child events indented after parent
tools/kvm_stat: separate drilldown and fields filtering
tools/kvm_stat: eliminate extra guest/pid selection dialog
tools/kvm_stat: mark private methods as such
tools/kvm_stat: fix debugfs handling
tools/kvm_stat: print error on invalid regex
tools/kvm_stat: fix crash when filtering out all non-child trace events
tools/kvm_stat: avoid 'is' for equality checks
tools/kvm_stat: use a more pythonic way to iterate over dictionaries
...
PMIC node requires external interrupts for proper operation, but property
defining them was missing. This was probably caused by a limited support
for interrupts from more than one parent, which was not possible to define
when support for this board was added. Fix this by adding
'interrupt-extended' property and properly define interrupt lines for PMIC
node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix the unit addresses of PDMA nodes in Exynos5410 (the reg property is
correct) to get rid of DTC warnings like:
arch/arm/boot/dts/exynos5410-odroidxu.dtb: Warning (simple_bus_reg):
Node /soc/amba/pdma@12680000 simple-bus unit address format error, expected "121a0000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Typo in unit address of PPMU ACP caused DTC warnings:
arch/arm/boot/dts/exynos4412-odroidu3.dtb:
Warning (simple_bus_reg): Node /soc/ppmu_acp@10ae0000 simple-bus unit address format error, expected "106e0000"
PPMU ACP (under 0x10ae0000 address) is present only in Exynos4210 so
move this node to exynos4210.dtsi with fixing the reg address to proper
one.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
split in 2 elements:
-Daughter board (part number: STM32MP157C-ED1)
which includes CPU, memory and power supply
-Mother board (part number: STM32MP157C-EM1)
which includes external peripherals (like display, camera,...)
and extension connectors.
The daughter board can run alone, this is why the device tree files
are split in two layers, for the complete evaluation board (ev1)
and for the daughter board alone (ed1).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch will add the chosen container to point stdout-path to serial2
and set the alias for spi0 to spi1 since the SPI NOR flash exists on SPI1.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now require all at24 users to use the "atmel,<model>" fallback in
device tree for different manufacturers.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Pull cleanup patchlet from Thomas Gleixner:
"A single commit removing a bunch of bogus double semicolons all over
the tree"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide/trivial: Remove ';;$' typo noise
This patch fixes the wrongly included dtsi file which
was breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS.
As per the board name, the correct file should be imx6dl.dtsi instead
of imx6q.dtsi
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Suggested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: 7a9caba55a ("ARM: dts: imx6dl: Add Engicam i.CoreM6 DualLite/Solo RQS initial support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the "i.MX 6Solo/6DualLite Applications Processor
Reference Manual" Rev. 3, 09/2017 there is no LCDIF unit on the
i.MX6DL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no pinctrl_usbotg_2 node in current Hummingboard dts files.
Drop reference to that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the USBOTG-ID pin to the correct definition. The top
USB port stays in device-mode without this change.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit name in order to fix the following
dtc warning with W=1:
arch/arm/boot/dts/imx28-tx28.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
They aren't needed by the etnaviv driver anymore and have been removed
from the binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
None of the slots support 1.8V signaling or SDIO. There is no point in
probing for a SD card on the eMMC controller.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for Advantech DMS-BA16 board, which uses
the Advantech BA-16 module.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a new node for reboot modes on LEGO MINDSTORMS EV3. The EV3's
bootloader looks for a magic number in the ARM local RAM and if found,
it will boot into a special firmware update mode where the flash memory
can be written via USB.
This has been testing working using the command:
# systemctl reboot loader
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a description of the RPi3 GPIO expander that the VC4 firmware controls.
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This allows adding devices for which the firmware exposes control interface
via the mailbox. An example of such device is the GPIO expander.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Since 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
the bcm2835-i2s requires a clock as DT property. Unfortunately
the necessary DT change has never been applied. While we are at it
also fix the first PCM register range to cover the PCM_GRAY register.
Fixes: 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13
carry altenate function, ALT5 for ARM JTAG
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Henry Zhang <henryzhang62@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Device nodes in device tree should use generic names, so rename
all existing power domains to "power-domain". To keep readable domain
names in debug logs, use label property, which has been introduce by
commit b13b2330aa ("soc: samsung: pm_domains: Read domain name from
the new label property");
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This adds support for the MMS152 found on N710x boards.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A section type mismatch warning shows up when building with LTO,
since orion_ge00_mvmdio_bus_name was put in __initconst but not marked
const itself:
include/linux/of.h: In function 'spear_setup_of_timer':
arch/arm/mach-spear/time.c:207:34: error: 'timer_of_match' causes a section type conflict with 'orion_ge00_mvmdio_bus_name'
static const struct of_device_id timer_of_match[] __initconst = {
^
arch/arm/plat-orion/common.c:475:32: note: 'orion_ge00_mvmdio_bus_name' was declared here
static __initconst const char *orion_ge00_mvmdio_bus_name = "orion-mii";
^
As pointed out by Andrew Lunn, it should in fact be 'const' but not
'__initconst' because the string is never copied but may be accessed
after the init sections are freed. To fix that, I get rid of the
extra symbol and rewrite the initialization in a simpler way that
assigns both the bus_id and modalias statically.
I spotted another theoretical bug in the same place, where d->netdev[i]
may be an out of bounds access, this can be fixed by moving the device
assignment into the loop.
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
probe and removal of special opps from the phycore boards that may
run the cpu outside the soc-vendor specs.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqHdYgQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgWwyCACeLElOaIYbFWectAjRvpYhOBMwk4mk/qA+
R5MLVhYRBshyb7KcTG4aBuP/FjrY68BllkxR5ANSF0GZCvvxTGgW3/XCouTRtRjd
YLIMlVKZZPokXEYxN1lqwgJjPx0pHBmDjwWcmU1cJ0gr6z5+/lPwYQW1x43S/yqd
T01vP7TsltG7U5Ai+prQfnWkjcKbPZUEqxDtWIRHqNeudJbcIoiWCOC4H+kYbygN
/w9UvaqGdD97Zs//v3jSxxB9CDdX3EScbPPSLhwFjj5Zckm6GJBRSbO2TWnsPv/H
Ed83duV1eSfIePbRIu2Qk6XrUdFU37GKlNA9SNDE58nphYTW7y2R
=Rdqg
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts32 fixes for 4.16" from Heiko Stübner:
Fix wrong dwmmc tuning clocks that may make probing HS cards fail to
probe and removal of special opps from the phycore boards that may
run the cpu outside the soc-vendor specs.
* tag 'v4.16-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Fix DWMMC clocks
ARM: dts: rockchip: Remove 1.8 GHz operation point from phycore som
This is mostly SoC related fixes for clocks, interconnect, and PM with few
board specifc dts related fixes:
- Fix quirk handling for ti-sysc to check all quirk flags instead of just
the first one
- Fix LogicPD boards for i2c1 muxing to avoid intermittent PMIC errors
- Fix debounce-interval use for omap5-uevm
- Fix debugfs_create_*() usage for omap1
- Fix sar_base initialization for HS omaps
- Fix omap3 prm wake interrupt for resume
- Fix kmemleak for omap_get_timer_dt()
- Enable optional clocks before main clock to prevent interconnect target
module from being stuck in transition
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlqHIH4RHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXMGvRAAy67hEsJnXBMCFTasvruXcJ36H7E9csFj
DRGvfpSvD7+EyqbMT4g9yCWaOtriHoEpZbnlfjqlE/p6Ck6Uh49tcQxqXlwXOvAn
hMwLGxcvSSLpaTQ/VLbDlUykhE8BBL4jcOjAsCYtcZ5gX6d7ksC0yMmnLwxKVva5
zeBCl7qASRCC8/45fSVJ9qGgS2miH215hjQYnQxg9C05iyz6sXeDwt1kVTQ0nB3P
1TIcb2v3EJwWRr/Q/iKoW/jVfrYfrnbh3i4I3LmfUm9zknhv2rpMrgymq7WTBUAT
EkaWjXpMgZ0HIwGn2QMPZzY7Y9k37mrcWNBxDR6HpxlmkWKmSlO2KtTAGkO+Bg46
D/GvDKBc7H8QJG9AyT5WXK0R9ofjXN1FXtC/k4XSVUjUnGtghYN1gg8D2U4p56Uv
zoDhjfqhokhrVIomZYEJ6QRHSO7ZV/izEEN/FDQSLGElaigz4/lsBMFE7J1kul1v
SnNTsrAHg2UqEfA95VOtJ1eMNPDBE1lJo9wEsGwiLYZv/tvfMAAheGsJqMzbiIE8
4oRiYPvh8pR9CeTKYp21I1CkU7BE/Nwse7jXj+0fq/XdnHrDzCpLpD3DNanZSplu
ZxZT01D7LQ/tL76APY6DyndYbMKxGypZgreZrDFudmRazgWOOD8B1tWe/9KHv1C5
lLpd9EAUBys=
=cN4I
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/fixes-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.16-rc cycle
This is mostly SoC related fixes for clocks, interconnect, and PM with few
board specifc dts related fixes:
- Fix quirk handling for ti-sysc to check all quirk flags instead of just
the first one
- Fix LogicPD boards for i2c1 muxing to avoid intermittent PMIC errors
- Fix debounce-interval use for omap5-uevm
- Fix debugfs_create_*() usage for omap1
- Fix sar_base initialization for HS omaps
- Fix omap3 prm wake interrupt for resume
- Fix kmemleak for omap_get_timer_dt()
- Enable optional clocks before main clock to prevent interconnect target
module from being stuck in transition
* tag 'omap-for-v4.16/fixes-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix checking of no-reset-on-init quirk
ARM: dts: LogicPD SOM-LV: Fix I2C1 pinmux
ARM: dts: LogicPD Torpedo: Fix I2C1 pinmux
ARM: dts: OMAP5: uevm: Fix "debounce-interval" property misspelling
ARM: OMAP1: clock: Fix debugfs_create_*() usage
ARM: OMAP2+: Fix sar_base inititalization for HS omaps
ARM: OMAP3: Fix prm wake interrupt for resume
ARM: OMAP2+: timer: fix a kmemleak caused in omap_get_timer_dt
ARM: OMAP2+: hwmod_core: enable optional clocks before main clock
- Updating my emails address (from free-electrons to bootlin)
- Adding back the selection of the PL310 Errata fix for the Cortex A9
based Armada SoCs (Armada 375 and 38x)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWoVeyAAKCRALBhiOFHI7
1aIEAJ47rHwesxLkkkNmuaMGdDplMGoj7gCgqjpKQNQDhf8Jk1+cWU95if/rqWo=
=XtHS
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.16-1' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fixes for 4.16 (part 1)" from Gregory CLEMENT:
- Updating my emails address (from free-electrons to bootlin)
- Adding back the selection of the PL310 Errata fix for the Cortex A9
based Armada SoCs (Armada 375 and 38x)
* tag 'mvebu-fixes-4.16-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Fix broken PL310_ERRATA_753970 selects
MAINTAINERS: update email address for Gregory CLEMENT
Building with LTO revealed that three spi_board_info arrays are marked
__initconst, but not const:
arch/arm/mach-davinci/board-dm365-evm.c: In function 'dm365_evm_init':
arch/arm/mach-davinci/board-dm365-evm.c:729:30: error: 'dm365_evm_spi_info' causes a section type conflict with 'dm646x_edma_device'
static struct spi_board_info dm365_evm_spi_info[] __initconst = {
^
arch/arm/mach-davinci/dm646x.c:603:42: note: 'dm646x_edma_device' was declared here
static const struct platform_device_info dm646x_edma_device __initconst = {
This marks them const as well, as was originally intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The array of string pointers is put in __initconst, and the strings themselves
are marke 'const' but the the pointers are not, which caused a warning when
built with LTO:
arch/arm/mach-clps711x/board-dt.c:72:20: error: 'clps711x_compat' causes a section type conflict with 'feroceon_ids'
static const char *clps711x_compat[] __initconst = {
This marks the array itself const as well, which was certainly the
intention originally.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On lkml suggestions were made to split up such trivial typo fixes into per subsystem
patches:
--- a/arch/x86/boot/compressed/eboot.c
+++ b/arch/x86/boot/compressed/eboot.c
@@ -439,7 +439,7 @@ setup_uga32(void **uga_handle, unsigned long size, u32 *width, u32 *height)
struct efi_uga_draw_protocol *uga = NULL, *first_uga;
efi_guid_t uga_proto = EFI_UGA_PROTOCOL_GUID;
unsigned long nr_ugas;
- u32 *handles = (u32 *)uga_handle;;
+ u32 *handles = (u32 *)uga_handle;
efi_status_t status = EFI_INVALID_PARAMETER;
int i;
This patch is the result of the following script:
$ sed -i 's/;;$/;/g' $(git grep -E ';;$' | grep "\.[ch]:" | grep -vwE 'for|ia64' | cut -d: -f1 | sort | uniq)
... followed by manual review to make sure it's all good.
Splitting this up is just crazy talk, let's get over with this and just do it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The DT node should be named after its functionality and not after the
IP it's defining.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The TBS A711 has an AXP813 PMIC and a soldered battery, thus, we enable
the battery power supply subnode in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The X-Powers AXP81X PMIC exposes battery supply various data such as
the battery status (charging, discharging, full, dead), current max
limit, current current, battery capacity (in percentage), voltage max
and min limits, current voltage, and battery capacity (in Ah).
This adds the battery power supply subnode for AXP81X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a DT node for the ADC of the PMIC so that there can be
consumers of its IIO channels declaring their consumptions via DT.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a DT node for the ADC of the PMIC so that there can be
consumers of its IIO channels declaring their consumptions via DT.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a DT node for the ADC of the PMIC so that there can be
consumers of its IIO channels declaring their consumptions via DT.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On both the ast2400 and ast2500 SoCs, the LPC reset controller is
required to bring the UARTs out of reset without waiting for the LPC
reset to be deasserted.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The ux500 PMU IRQ bouncer is getting in the way of some fundametnal
changes to the ARM PMU driver, and it's the only special case that
exists today. Let's remove it.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
"Midas" is the codename for a family of smartphones released by Samsung
Mobile. It includes the Galaxy S3 (GT-I9300/I9305) and the Galaxy
Note 2 (GT-N7100/N7105). The boards largely have the same peripherals:
the main differences are touchscreen, display panel and cellular modem.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Midas boards share a lot with Trats2. Split the common parts
out of Trats2 into a common Midas DTSI and a common "Galaxy S3" DTS.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable the display pipeline and HDMI output for the Orange Pi mini
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
These hogs are for parts of the system that need to be in this state,
but do not yet have a driver associated with them but they must be
configured in order to successfully boot the host.
There are also some pinmux hogs, where the default mode of the IP block
is configured.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
These describe the front panel LEDs that are present on a Palmetto
chassis, and the checkstop GPIO that comes from the Power8 CPU to
indicate a host error.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The LPC device uses LCLK.
Tested-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This addresses some differences between the G5 and G4 LPC nodes that
make them hard to compare. There is no functional change.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
These BMC systems require this device to communicate with the host.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The IPMI BT device part of the LPC interface and is used for
communication with the host processor.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the display pipeline and HDMI output
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently, same stm32f746-pinctrl driver is used for stm32f746 and
stm32f769 MCU. As pin map is different between those 2 MCUs,
a stm32f769-pinctrl driver has been recently added.
This patch
-allows to use stm32f769-pinctrl driver for stm32f769 boards
-reworks stm32 devicetree files to fit with stm32f746 / stm32f769
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
This error has propagated across the 32-bit DTs too, so fix those up.
Fixes: 187d7967a5 ("ARM: dts: rockchip: add the sdio/sdmmc node for rk3036")
Fixes: faea098e18 ("ARM: dts: rockchip: add core rk3036 dtsi")
Fixes: 9848ebeb95 ("ARM: dts: rockchip: add core rk3228 dtsi")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
BananaPi M3 includes HDMI connector, so add support for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This commit adds all bits necessary for HDMI on A83T - mixer1, tcon1,
hdmi, hdmi phy and hdmi pinctrl entries.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 stores some magic flags in a portion of the secure SRAM. The
BROM jumps directly to the software entry point set by the SMP code
if the flags are set. This is required for CPU0 hotplugging.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The PRCM is a collection of clock controls, reset controls, and various
power switches/gates. Some of these can be independently listed and
supported, while a number of CPU related ones are used in tandem with
CPUCFG for SMP bringup and CPU hotplugging.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
CPUCFG is a collection of registers that are mapped to the SoC's signals
from each individual processor core and associated peripherals, such as
resets for processors, L1/L2 cache and other things.
These registers are used for SMP bringup and CPU hotplugging.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A80 includes an ARM CCI-400 interconnect to support multi-cluster
CPU caches.
Also add the maximum clock frequency for the CPUs, as listed in the
A80 Optimus Board FEX file.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
In banked-sr.c, we use a top-level '__asm__(".arch_extension virt")'
statement to allow compilation of a multi-CPU kernel for ARMv6
and older ARMv7-A that don't normally support access to the banked
registers.
This is considered to be a programming error by the gcc developers
and will no longer work in gcc-8, where we now get a build error:
/tmp/cc4Qy7GR.s:34: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_usr'
/tmp/cc4Qy7GR.s:41: Error: Banked registers are not available with this architecture. -- `mrs r3,ELR_hyp'
/tmp/cc4Qy7GR.s:55: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_svc'
/tmp/cc4Qy7GR.s:62: Error: Banked registers are not available with this architecture. -- `mrs r3,LR_svc'
/tmp/cc4Qy7GR.s:69: Error: Banked registers are not available with this architecture. -- `mrs r3,SPSR_svc'
/tmp/cc4Qy7GR.s:76: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_abt'
Passign the '-march-armv7ve' flag to gcc works, and is ok here, because
we know the functions won't ever be called on pre-ARMv7VE machines.
Unfortunately, older compiler versions (4.8 and earlier) do not understand
that flag, so we still need to keep the asm around.
Backporting to stable kernels (4.6+) is needed to allow those to be built
with future compilers as well.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84129
Fixes: 33280b4cd1 ("ARM: KVM: Add banked registers save/restore")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The A20 has an ARM Mali 400 GPU, so add binding to our DT.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Rockchip recommends to run the CPU cores only with operations points of
1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default
values instead.
Fixes: 903d31e346 ("ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The mmc1_pins node with bias-pull-up attribute is already defined in
the sunxi-h3-h5.dtsi file. Thus, we can remove it from here.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinctrl configuration for mmc0 and mmc1 so let's
drop the _a suffix from both of them.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Most of the boards use the mmc1 pins and their attributes defined in
mmc1_pins_a. Let's default to that by moving the pinctrl attributes to
the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the Droid 4 devicetree to properly describe the reset
GPIO. Also rename the node to touchscreen instead of tsp,
which seems to be commonly used for touchscreens.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for the PDU001 board from EETS GmbH.
The board is built around the byteENGINE module AM335X from
bytes at work AG which in turn is built around a Sitara SoC
from TI.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds dts support for magnetometer on Nokia N9.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: fix missing bracket]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at times.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD DM3730
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, depending on data type.
Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.
Correct all wrong usage:
- clk.rate is unsigned long, not u32,
- clk.flags is u8, not u32, which exposed the successive
clk.rate_offset and clk.src_offset fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
HS omaps use irq_save_secure_context() instead of irq_save_context()
so sar_base will never get initialized and irq_sar_clear() gets called
with a wrong address for HS omaps from irq_restore_context().
Starting with commit f4b9f40ae9 ("ARM: OMAP4+: Initialize SAR RAM
base early for proper CPU1 reset for kexec") we have it available,
and this ideally would been fixed with that commit already.
Fixes: f4b9f40ae9 ("ARM: OMAP4+: Initialize SAR RAM base early for
proper CPU1 reset for kexec")
Cc: Andrew F. Davis <afd@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For platform_suspend_ops, the finish call is too late to re-enable wake
irqs and we need re-enable wake irqs on wake call instead.
Otherwise noirq resume for devices has already happened. And then
dev_pm_disarm_wake_irq() has already disabled the dedicated wake irqs
when the interrupt triggers and the wake irq is never handled.
For devices that are already in PM runtime suspended state when we
enter suspend this means that a possible wake irq will never trigger.
And this can lead into a situation where a device has a pending padconf
wake irq, and the device will stay unresponsive to any further wake
irqs.
This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. Then try to wake up the system by typing to the serial
console.
Note that this affects only omap3 PRM interrupt as that's currently
the only omap variant that does anything in omap_pm_wake().
In general, for the wake irqs to work, the interrupt must have either
IRQF_NO_SUSPEND or IRQF_EARLY_RESUME set for it to trigger before
dev_pm_disarm_wake_irq() disables the wake irqs.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When more than one GP timers are used as kernel system timers and the
corresponding nodes in device-tree are marked with the same "disabled"
property, then the "attr" field of the property will be initialized
more than once as the property being added to sys file system via
__of_add_property_sysfs().
In __of_add_property_sysfs(), the "name" field of pp->attr.attr is set
directly to the return value of safe_name(), without taking care of
whether it's already a valid pointer to a memory block. If it is, its
old value will always be overwritten by the new one and the memory block
allocated before will a "ghost", then a kmemleak happened.
That the same "disabled" property being added to different nodes of device
tree would cause that kind of kmemleak overhead, at least once.
To fix it, allocate the property dynamically, and delete static one.
Signed-off-by: Qi Hou <qi.hou@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti) on
all gpio ports of stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds system config support for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti)
for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Most of the boards use the mmc0 pins and their attributes defined in
mmc0_pins_a. Let's default to those by moving the pinctrl attributes
to the dtsi file. This makes it easier to modify device trees in the
future as there is only one place to change the pinctrl attributes.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GPIO card detection pin (mmc0_cd_pin) is already requested and
configured by mmc_gpiod_request_cd() in drivers/mmc/core/slot-gpio.c
so pinctrl is not needed.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
factor and GPIO holes similar to Raspberry Pi Zero.
It features:
- Allwinner H2+ SoC
- Single-chip (16-bit) 512MiB DDR3 DRAM
- Ampak AP6212 Wi-Fi/Bluetooth module
- MicroSD slot
- Two MicroUSB Type-B ports (one can only be used to power the board and
the other features OTG functionality)
- Two keys, a reset and a GPIO-connected key.
- HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
- CSI connector to connect the camera sensor provided by Sinovoip.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4412 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4210 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4 boards should use them
as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The exynos5440 device tree is the only one left, which does not use
"soc" node. Add a "soc" node to exynos5440.dtsi in order to make it
consistent with other exynos DTS.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In order to use soc node, we need to reference soc child nodes by label
in exynos4412. Define pmu label in exynos4.dtsi. Use it in exynos4412
instead of redefining the node by full path.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The exynos-syscon-restart.dtsi is already included by exynos5.dtsi
(through exynos54xx.dtsi).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Extend camera node by label, not by full path in Exynos
4412 Itop Elite. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera and i2c1_isp nodes by labels, not by full path in Exynos
4412 Trats2. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera node by label, not by full path in Exynos 4412 Odroid
boards. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera node by label, not by full path in Exynos 4412 DTSI.
This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera, fimc, mct and sysram nodes by labels, not by full path in
Exynos 4210 Universal C210 board. This avoids error-prone redefinition
of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera and fimc nodes by labels, not by full path in Exynos
4210 Trats board. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Extend camera, mixer and tmu nodes by labels, not by full path in Exynos
4210 DTSI. This avoids error-prone redefinition of nodes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Define pinctrl labels in exynos4412.dtsi and use them in
exynos4412-pinctrl.dtsi, as it is done in other Exynos DTSes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
"debounce_interval" was never supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The compatible string is incorrect. Add atmel,sama5d3-pinctrl since
it's the appropriate compatible string. Remove the
atmel,at91rm9200-pinctrl compatible string, this fallback is
useless, there are too many changes.
Signed-off-by: Santiago Esteban <Santiago.Esteban@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #v3.18
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The node is referred to as a DAI from the sound node and should
therefore have a #sound-dai-cells property.
Fixes: 21dd0ece34 ("ARM: dts: at91: add devicetree for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The lvds encoder chip was omitted by oversight. Add it.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The nattis currently relies on the cmdline to correctly configure the
MTD partition table, and the one given in the device tree is simply
ignored. Which is fortunate, since the device tree partition table is
bonkers and does not match reality.
So, in order to avoid confusion, fix the device tree partition table
to match what is expected (i.e. what is normally provided on the cmdline).
In particular, the rootfs partition should be mtd6.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The used part does contain an eeprom compatible with an Atmel 24c02
chip and it is from NXP, but it is not called 24c02. It's actually a
se97b chip. Adjust the compatible accordingly.
Fixes: 21dd0ece34 ("ARM: dts: at91: add devicetree for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The used part does contain an eeprom compatible with an Atmel 24c02
chip and it is from NXP, but it is not called 24c02. It's actually a
se97b chip. Adjust the compatible accordingly.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The copyright holder for this work is Microchip (formerly Atmel)
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The node name should be generic and must not contain the part number.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The MACH_ARMADA_375 and MACH_ARMADA_38X boards select ARM_ERRATA_753970,
but it was renamed to PL310_ERRATA_753970 by commit fa0ce4035d ("ARM:
7162/1: errata: tidy up Kconfig options for PL310 errata workarounds").
Fix the selects to use the new name.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Fixes: fa0ce4035d ("ARM: 7162/1: errata: tidy up Kconfig options for
PL310 errata workarounds"
cc: stable@vger.kernel.org
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This clock node is unused, remove it.
This allows to fix the following warnings when compiling
dtb with W=1 option :
arch/arm/boot/dts/stih410-b2120.dtb: Warning (simple_bus_reg):
Node /clocks/clockgen-c0 missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2260.dtb: Warning (simple_bus_reg):
Node /clocks/clockgen-c0 missing or empty reg/ranges property
arch/arm/boot/dts/stih418-b2199.dtb: Warning (simple_bus_reg):
Node /clocks/clockgen-c0 missing or empty reg/ranges property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move sound node outside soc node and sti_sasg_codec node
as child of syscfg_core node.
This allows to fix the following warning when compiling
dtb with W=1 option:
arch/arm/boot/dts/stih407-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@0 has a unit name, but no reg property
arch/arm/boot/dts/stih407-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@1 has a unit name, but no reg property
arch/arm/boot/dts/stih407-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@2 has a unit name, but no reg property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (simple_bus_reg):
Node /soc/sti-sasg-codec missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@0 has a unit name, but no reg property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@1 has a unit name, but no reg property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@2 has a unit name, but no reg property
arch/arm/boot/dts/stih407-b2120.dtb: Warning (simple_bus_reg):
Node /soc/sound missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (simple_bus_reg):
Node /soc/sti-sasg-codec missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2260.dtb: Warning (unit_address_vs_reg):
Node /soc/sound/simple-audio-card,dai-link@0 has a unit name, but no reg property
arch/arm/boot/dts/stih410-b2260.dtb: Warning (simple_bus_reg):
Node /soc/sti-sasg-codec missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2260.dtb: Warning (simple_bus_reg):
Node /soc/sound missing or empty reg/ranges property
arch/arm/boot/dts/stih418-b2199.dtb: Warning (simple_bus_reg):
Node /soc/sti-sasg-codec missing or empty reg/ranges property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Bananapi M3 has two controllable LEDs, blue and green, that are tied
to the PMIC's two GPIO pins.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Mele I7 has an HDMI connector wired to the HDMI pins
on the SoC. Enable the display pipeline and HDMI output.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Added "dts" prefix]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Enable the display pipeline and HDMI output on the Olimex
A20-SOM-EVB.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Including sun4i header instead of sun7i prevents using sun7i specific
defines.
Substitute header inclusion in sun7i-a20.dtsi using right one.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A20-SOM204 board has option with onboard 16GB eMMC.
The chip is wired to MMC2 slot.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is new System-On-Module platform with universal dimm socket for
easy insertation. The EVB board is designed to be universal with
future modules. Product page is located here [1].
There are two dts files - one for base model and another for eMMC variant.
Base features of A20-SOM204 board includes:
* 1GB DDR3 RAM
* AXP209 PMU
* KSZ9031 Gigabit PHY
* AT24C16 EEPROM
* Status LED
* LCD connector
* GPIO connector
There will be variants with the following options:
* Second LAN8710A Megabit PHY
* 16MB SPI Flash memory
* eMMC card
* ATECC508 crypto device
The EVB board has:
* Debug UART
* MicroSD card connector
* USB-OTG connector
* Two USB host
* RTL8723BS WiFi/BT combo
* IrDA transceiver/receiver
* HDMI connector
* VGA connector
* Megabit ethernet transceiver
* Gigabit ethernet transceiver
* SATA connector
* CAN driver
* CSI camera
* MIC and HP connectors
* PCIe x4 connector
* USB3 connector
* Two UEXT connectors
* Two user LEDs
Some of the features are multiplexed and cannot be used the same time:
CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3.
[1] https://www.olimex.com/Products/SOM204/
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display pipeline and HDMI output.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display pipeline and HDMI output
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable the WiFi (AP6212) chip and eMMC support for the NanoPi NEO Air.
This patch was originally submitted by Jelle van der Waa. Martin Kelly
modified it to compile on the latest kernel, fixed up some review
comments from Maxime Ripard, and re-tested the patch.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-sunxi@googlegroups.com
Cc: devicetree@vger.kernel.org
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Odroid-C1+ board is equipped with an RTL8211F ethernet PHY
which supports 10/100/1000 Mbps ethernet.
The PHY reset and interrupt lines are controlled by the SoC via
two GPIO lines (GPIOH_4 and GPIOH_3 respectively).
The PHY energy efficient ethernet (eee) mode is marked as broken
using "eee-broken-1000t" because, during tests, high packet losses
were experienced without it.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable S805 (aka Meson8b) ethernet pin multiplexing and
extend the controller description.
The programmable ethernet (PRG_ETHERNET) register address
value (0xc1108108), contained in meson.dtsi, is overridden
according to the value found in S805 SoC manual.
This also required to switch to "amlogic,meson8b-dwmac" compatible
to correctly configure that register.
The two clock sources "clkin0" and "clkin1" are both equals
to MPLL2 because, as reported in bit 9-7 register description,
that is the only Meson8b ethernet clock source.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Tested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now that we support the reset controller on Meson8 we can add the reset
line to the USB PHYs (just like on Meson8b).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Meson8 uses the same reset controller as Meson8b. Add the node along
with the #include for the reset lines to meson8.dtsi so we can use it
from there as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The reset controller in the Meson8b SoCs also supports level resets.
These use the same defines (from
dt-bindings/reset/amlogic,meson8b-reset.h) as the reset pulses.
The reset-meson driver internally handles the difference if a consumer
requests a reset pulse or a level reset. However, for this to work we
must extend the memory zone of the reset controller.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Labels for pinctrl's are defined in exynos4210.dtsi. Use them in
exynos4210-pinctrl instead of full names, as it is done in other Exynos
DTSes.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The only user of DTSI for Samsung K3PE0E000B memory was removed in
commit fa63d03728 ("ARM: dts: omap5: Make uevm as the official board
and deprecate sevm support") so get rid of this DTSI as well.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The display frontend can be used to do hardware scaling, colorspaces
conversion or to implement the buffer format output by the Cedar VPU.
Since we're starting to have some support for it in the DRM driver, let's
enable its DT node.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This board has a SPI flash, activate it also in device tree by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Artik 520 module, there is a bcm4354 attached to mshc_1. Enable
it and turn on the regulator used for it, so that both WiFi & Bluetooth
will work.
Verified to work on the Artik 520 evaluation board.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As sti-display-subsystem sub-nodes (sti-compositor, sti-tvout
sti-hdmi, sti-hda and sti-hqvdp) are SoC's IP, we add a fake
reg property.
This allows to fix the following warning when compiling
dtb with W=1 option:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (unit_address_vs_reg):
Node /soc/sti-display-subsystem/sti-hda@8d02000 has a unit name, but no reg property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Leds are not part of soc, so nove them outside soc node.
This allows to fix the following warnings when compiling
dtb with W=1 option :
arch/arm/boot/dts/stih407-b2120.dtb: Warning (simple_bus_reg):
Node /soc/leds missing or empty reg/ranges property
arch/arm/boot/dts/stih410-b2120.dtb: Warning (simple_bus_reg):
Node /soc/leds missing or empty reg/ranges property
arch/arm/boot/dts/stih418-b2199.dtb: Warning (simple_bus_reg):
Node /soc/leds missing or empty reg/ranges property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove leading 0x and 0s from bindings notation
Add missing unit-address and remove some which are useless.
This allows to fix several warnings like :
Warning (unit_address_vs_reg): Node XXXX has a reg or ranges property, but no unit name
Warning (simple_bus_reg): Node XXXX simple-bus unit address format error, expected "123456"
Warning (unit_address_vs_reg): Node XXXX has a unit name, but no reg property
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support for the Computer on Module Colibri iMX6ULL and its
Bluetooth/Wifi variant along with the development/evaluation carrier
board device trees. Follow the usual hierarchic include model,
maintaining shared configuration in imx6ull-colibri.dtsi and
imx6ull-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is a rebased version of patch [0].
The 32 kHz reference clock on the i.MX6UL(L) can be output by
setting the external signal XTALOSC_REF_CLK_32K in one of the
following ways [1]:
|----------------------------------------------------------|
| Signal | Pad | Mode | Direction |
|----------------------------------------------------------|
| XTALOSC_REF_CLK_32K | ENET1_RX_EN | ALT2 | O |
| | GPIO1_IO03 | ALT3 | |
| | JTAG_TCK | ALT6 | |
|----------------------------------------------------------|
Before patch [2] the mux mode for the external reference clock was
missing. The patch named the mux mode as used in the NXP Linux
4.9.11_1.0.0 release, but the Reference Manual uses the name
OSC32K_32K_OUT, e.g. in [3].
As Philipp and Shawn suggest the name from the RM should be used
instead.
[0] https://patchwork.kernel.org/patch/10172187/
[1] IMX6ULRM, Rev. 1, 04/2016, Table 58-1, p. 3649
[2] https://patchwork.kernel.org/patch/10156121/
[3] IMX6ULRM, Rev. 1, 04/2016, 30.5.47 SW_MUX_CTL_PAD_ENET1_RX_EN SW MUX
Control Register (IOMUXC_SW_MUX_CTL_PAD_ENET1_RX_EN), p. 1357
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ull-14x14-evk.dts currently includes the imx6ul.dtsi file for an
i.MX6ULL SoC which is plain wrong.
Rename the current imx6ul-14x14-evk.dts to .dtsi and include it from
imx6ul-14x14-evk.dts and imx6ull-14x14-evk.dts, so that both can
include the appropriate SoC specific (imx6ul.dtsi/imx6ull.dtsi) file.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Put the UART clock node directly under root with a unique node name and
drop unit-address in order to fix the following build warning with W=1:
arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dtb: Warning (simple_bus_reg): Node /clocks/osc26m missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The missing last digit of the CONFIG values is added. Looks like a typo
of some sort when comparing to the downstream dt. This fixes
intermittent behavior behaviour of the ethernet controllers.
Signed-off-by: Aapo Vienamo <aapo@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The eSDHC does not work properly if the SION bit is not set for the
bidirectional CMD signal, whatever the eSDHC instance and the selected
pad. Therefore, setting SION is mandatory for all eSDHC CMD ports. Do
this for MX25_PAD_*__ESDHCn_CMD in imx25-pinfunc.h in order to enforce
this behavior for all boards.
This had already been done for eSDHC1, but not for eSDHC2. Also, define
MX25_PAD_FEC_MDC__ESDHC2_CMD so that all the possible cases are covered
from now on.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This file had several naming inconsistencies for eSDHC:
- the instances were named sometimes SDn, sometimes SDHCn, whereas they
are named ESDHCn in the reference manual, e.g.:
MX25_PAD_SD1_CMD__SD1_CMD
MX25_PAD_D15__SDHC1_DAT7
- the data ports were named sometimes DATAn, sometimes DATn like in the
reference manual, e.g.:
MX25_PAD_SD1_DATA0__SD1_DATA0
MX25_PAD_D15__SDHC1_DAT7
- in one case, the clock port was named DAT_CLK instead of CLK:
MX25_PAD_CSI_D7__SDHC2_DAT_CLK
This change:
- introduces new definitions using the naming from the reference
manual,
- keeps definitions using the legacy naming in order not to break
compatibility for out-of-tree users (they can be removed later),
- updates the in-tree files that were using the legacy naming.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at24' as fallback is now deprecated - use the full
'atmel,<model>' string.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the empty reg property from the SoC dtsi files in order to avoid
duplicate memory nodes when the correct size is passed in board dts files.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In preparation for removing 'reg = <0 0>;' from the dtsi SoC files, pass
'reg = <0 0 >;' to the dts/dtsi board files that do not pass the memory
size.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PU power domain support, GPU is the only
module inside PU power domain, and PU power
is supplied by LDO_SOC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch configures the board to output UART6 to the mikroBus.
The NXP WaRP7 board can route UART6 to the mikroBus, where an RS232
click board can be plugged in to get an additional serial port.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Default boot medium must be internal eMMC, we don't want the SDIO to be
used for these devices. This commit disables the SD card interface for
GE Healthcare Bx50v3 devices.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PPD uses the PMIC's TSI pins in general purpose ADC mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Utilise new support in Atmel MaxTouch driver to drive the
touchscreen controllers reset line correctly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In i.MX 6ULL UART8 is part of the AIPS-3 memory map instead of
AIPS-1. Clocks and interrupts remain the same.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 6ULL features another IOMUX Controller called IOMUXC
SNVS which allows to control BOOT_MODE and TAMPER pins. Add the
controller to the i.MX 6ULL specific imx6ull.dtsi device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add per-core ARM architected timer. Unfortunately bootloaders (U-Boot)
currently do not make the necessary initialization. Also specifing the
clock manually using the clock-frequency property seems not to help.
Therefor leave the timer disabled by default for now.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Cortex-A7 and its GIC support virtualization extensions. To
make use of them the CPU private interrupt needs to be specified.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX 6ULL, the pin MUX and CTRL register of BOOT_MODEx and TAMPERx
pins are available through IOMUXC_SNVS. Add additional pinfunc defines.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PHYTEC phyBOARD-Mira with i.MX 6QuadPlus with NAND.
It is based on the phyBOARD-Mira with i.MX 6Quad/Dual and supports the
same interfaces.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PHYTEC phyBOARD-Mira Low-Cost Rapid Development Kit
with i.MX 6DualLight/Solo with NAND.
Following interfaces are supported:
- 100 MBit Ethernet
- USB Host
- RS232
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PHYTEC phyBOARD-Mira Rapid Development Kit with
i.MX 6Quad/Dual with eMMC or NAND.
Following interfaces are supported:
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
- LVDS
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board
for PHYTEC phyCORE-i.MX 6.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
6Quad/Dual or i.MX 6DualLight/Solo.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7D SDB has a MPL3115 Pressure sensor.
Add support for this sensor, which is included in the trivial i2c devices
and according to the bindings documentation, just need a compatible field
and an address.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 6UL EVK has a MAG3110 Magnetometer sensor in its base board.
Add support for this sensor, which is included in the trivial i2c devices
and according to the bindings documentation, just need a compatible field
and an address.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The system has an external watchdog in the environment processor
so the internal watchdog is of no use.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: cphealy@gmail.com
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ads7846 is connected to SPI chip select 0, so pass the unit address
accordingly to fix the following build warning with W=1:
arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dtb: Warning (unit_address_vs_reg): Node /soc/aipi@10000000/cspi@1000e000/ads7846 has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move i2cmux node from soc node to root node.
i2cmux node does not have any register properties and thus shouldn't be
placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx28-cfa10049.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbx@80040000/i2cmux missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:
arch/arm/boot/dts/imx28-apx4devkit.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc2-sck-cfg-apx4 missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass unit address and reg to IOMUX node to fix the following build
warning with W=1:
arch/arm/boot/dts/imx23-evk.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/gpmi-pins-fixup missing or empty reg/ranges property
arch/arm/boot/dts/imx23-evk.dtb: Warning (simple_bus_reg): Node /apb@80000000/apbh@80000000/pinctrl@80018000/mmc0-pins-fixup missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although the two nodes constitute one contiguous 128K region, still
describe them separately:
- That's how they are described in the reference manual: "Each OCRAM
occupies a 64 KB of address region...", and the names ocram1 and
ocram2 are also as used in the manual.
- The two areas are treated differently by the boot ROM code: OCRAM2 is
zero-initialized, while, again quoting the RM, "software must perform
the zero initialization of OCRAM1."
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make it possible to fallback to GPIO for I2C4 on the EXIO-E connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, corrected board name in subject, fixed aliases, switched
to named GPIOs, fixed pinmux for I2C4]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, corrected board name in subject, fixed aliases, switched
to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make it possible to fallback to GPIO for I2C4 on the EXIO-E connector.
This is based on reference work for the I2C0 core of the lager/r8a7790
by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOS, fixed pinmux for I2C4]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C2 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs, sorted by SCL
pins]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for da9063 PMIC and da9210 regulator
related I2C slaves.
Based on similar work for HDMI by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, corrected chip name in commit msg, updated aliases]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Create a separate bus for HDMI related I2C slaves.
Based on work by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, removed typo in comment, fixed aliases, switched to
named GPIOS, sort SCL pins first]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add VSP support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VSP support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7745 to DT with a disabled
status.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7743 to DT with a disabled
status.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together and sorted alphabetically.
Minor whitespace and line-wrapping changes are also made
to match the formatting of R-Car Gen2 SoCs.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together and sorted alphabetically.
Minor whitespace and line-wrapping changes are also made
to match the formatting of R-Car Gen2 SoCs.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space before a =.
This patch fixes instances where a tab is used instead.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space before a =.
This patch fixes instances where a tab is used instead.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space before a =.
This patch fixes instances where a tab is used instead.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
Also re-align comment of audio_clka to match other R-Car SoCs.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3, RZ/G1, and
R-Car V2H (R8A77920) SoCs upstream. It is intended to migrate other R-Car
Gen2 SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space after a =.
This patch removes instances where a tab is used instead.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3, RZ/G1, and
R-Car V2H (R8A77920) SoCs upstream. It is intended to migrate other R-Car
Gen2 SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Consistently use a single space after a =.
This patch removes instances where a tab is used instead. It also avoids
running over 80 columns in width in one of the lines where whitespace is
updated.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort subnodes of root node to aid maintenance.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3, RZ/G1, and
R-Car V2H (R8A77920) SoCs upstream. It is intended to migrate other R-Car
Gen2 SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
