This reverts commit 99082eab63 since it
breaks the build due to differing implementations of iowrite() and
ioread().
Signed-off-by: Mark Brown <broonie@kernel.org>
The core only supports up to 32 slaves, and the chipselect function
expects the same.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Small transfers generally can be accomplished faster in polling mode.
This patch select the transfer which size is bellow the buffer size to
be done on polling mode
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable never leaves the scope of txrx_bufs.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by using the unit used on most of the code logic.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by using the unit used on most of the code logic.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_rx handles the case where the buffer is null. Nevertheless spi_tx
did not handle it, and was handled by the caller function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by removing the tx and and rx function pointers and
substitute them by a single function.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core controls the chip select lines individually.
By default, all the lines are consider active_low. After
spi_setup_transfer, it has its real value.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When no irq is used, there is no need to inhibit the transmission for
every transaction. This inhibition was implemented to avoid a race
condition with the irq handler.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core can run in polling mode. In fact, the performance of the core
is similar (or even better), due to the fact most of the spi
transactions are just a couple of bytes and there is one irq per
transactions.
When an mtd device is connected via spi, reading 8MB of data produces
more than 80K interrupts (with irq disabling, context swith....)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control register has not changed since the previous access.
Therefore we can use the cached value and safe one bus access.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the transmission loop, check for remaining bytes at the loop
condition.
This way we can handle transmissions of 0 bytes and clean the code.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of enabling the IRQ and disabling it for every transaction.
Specially the small transactions (1,2 words) benefit from removing 3 bus
accesses.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of checking the TX_FULL flag for every transaction, find out the
size of the buffer at probe time and use it.
To avoid situations where the core had some data on the buffer before
initialization, the core is reseted before the buffer size is detected
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSPI module need cs change information in
a spi transfer. According to cs change, DSPI
will give last data the right flag. Bitbang
provide cs change behind the last data in
a transfer. So DSPI can not deal the last
data in every transfer properly, so remove
the bitbang in the driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pl08x driver originally selected S3C64XX_PL080 to avoid having
the legacy Samsung DMA interfaces. Those are now gone, so the
select is no longer needed, but it now causes problems when
CONFIG_DMA_ENGINE is disabled:
arch/arm/plat-samsung/built-in.o: In function `s3c64xx_spi0_set_platdata':
:(.init.text+0x518): undefined reference to `pl08x_filter_id'
This simply removes the 'select' to avoid this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently get a warning about potentially uninitialized variables
in the rockchip spi driver, at least in certain toolchain versions:
spi/spi-rockchip.c: In function 'rockchip_spi_prepare_dma':
include/linux/dmaengine.h:796:2: warning: 'txdesc' may be used uninitialized in this function
include/linux/dmaengine.h:796:2: warning: 'rxdesc' may be used uninitialized in this function
The reason seems to be that gcc cannot know whether the value
of the rs->rx and rs->tx variables change between the two points
these are accessed.
The code is actually correct, but to make this clearer to the
compiler, this changes the conditionals to test for the local
rxdesc/txdesc variables instead, which it knows won't change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7566bcc76b ("spi: pxa2xx: Move is_lpss_ssp() tests to caller") did
not check LPSS before calling lpss_ssp_setup() in pxa2xx_spi_resume().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_* API was supposed to be used only in probe function call.
Memory is allocated at 'probe' and free automatically at 'remove'.
Usage of devm_* functions outside probe sometimes leads to memory leak.
Avoid using devm_kzalloc in dspi_setup_transfer and use kzalloc instead.
Also add the dspi_cleanup function to free the controller data upon
cleanup.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The number of words in the read buffer will be exactly the same as the
number of words written on write buffer, once the transaction has
finished.
Instead of cheking the rx_empty flags for every word simply save the
number of words written by fill_tx_fifo.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock information is being kept in the custom register on Intel MID
platforms. Each controller has its own dedicated custom register for that.
Thus, to get a proper frequency we have to read value from the specific offset
to the register block. This patch makes this happen.
Fixes: d58cf5ff65 (spi: dw-pci: describe Intel MID controllers better)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hardware supports LOOP mode. Support it also in the driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hardware supports LSB_FIRST mode. Support it also in the driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds support for multiple hardware chip selects to spi-orion.
Different SoCs support different number of chip selects (up to
8 on some platforms). The driver allows up to this number, and it is up
to the implementer to only use the chip selects that are available.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_setup() will test unsupported mode bits before calling spi->master->setup.
Thus remove duplicate code to test unsupported mode bits in spi_st_setup().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit changes spi-orion to provide setup, set_cs, and transfer_one
functions instead of transfer_one_message. This allows chip select support
for both native and GPIO chip selects to be added.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are more that one SPI controller on the Intel MID boards. This patch
describes the status and IDs of them. From now on we also have to care about
bus number that must be unique per host.
According to the specification the SPI1 has 5 bits for chip selects and SPI2
only 2 bits. The patch makes it depend to PCI ID.
The first controller (SPI1) is DMA capable, meanwhile SPI2 can share same
channels (via software switch) such functionality is not in the scope of this
patch. Thus, attempt to init DMA for SPI2 will always fail for now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When autodetection is used it would be useful to know what the FIFO size is.
The patch adds a debug message for this purpose.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of warning message in ->probe() we have to use HW device name instead
of master because last is not defined yet.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no need to use the synchronous version.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
"sirf,marco-spi" is redundant as all SPI controllers in CSR SiRFSoC are
compatible with prima2-spi.
at the same time, the whole marco project was dropped and its replacement
atlas7 is also compatible with prima2 in SPI.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the following kbuild test robot warnings:
>> drivers/spi/spi-dln2.c:124:1-4: WARNING: end returns can be simplified if negative or 0 value
>> drivers/spi/spi-dln2.c:656:1-4: WARNING: end returns can be simplified if negative or 0 value
Additionally, fix a comment after switching from CONFIG_PM_RUNTIME to
CONFIG_PM.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the FLD bit field is bit[3:2], the MDR1_FLD_MASK value should
be 0x0000000c.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO size is 40 accordingly to the specifications, but this means 0x40,
i.e. 64 bytes. This patch fixes the typo and enables FIFO size autodetection
for Intel MID devices.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code tries to find the highest valid fifo depth by checking the value
it wrote to DW_SPI_TXFLTR. There are a few problems in current code:
1) There is an off-by-one in dws->fifo_len setting because it assumes the latest
register write fails so the latest valid value should be fifo - 1.
2) We know the depth could be from 2 to 256 from HW spec, so it is not necessary
to test fifo == 257. In the case fifo is 257, it means the latest valid
setting is fifo = 256. So after the for loop iteration, we should check
fifo == 2 case instead of fifo == 257 if detecting the FIFO depth fails.
This patch fixes above issues.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The irq number is only used inside the probe function, so there is really no
need to store it in the private structure.
Use a local 'irq' variable to hold the the irq number instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Device support SPI_CPOL, but driver have missed to add
support for this configuration.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Once the current message is finished, the driver notifies SPI core about
this by calling spi_finalize_current_message(). This function queues next
message to be transferred. If there are more messages in the queue, it is
possible that the driver is asked to transfer the next message at this
point.
When spi_finalize_current_message() returns the driver clears the
drv_data->cur_chip pointer to NULL. The problem is that if the driver
already started the next message clearing drv_data->cur_chip will cause
NULL pointer dereference which crashes the kernel like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
IP: [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
PGD 78bb8067 PUD 37712067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 1 PID: 11 Comm: ksoftirqd/1 Tainted: G O 3.18.0-rc4-mjo #5
Hardware name: Intel Corp. VALLEYVIEW B3 PLATFORM/NOTEBOOK, BIOS MNW2CRB1.X64.0071.R30.1408131301 08/13/2014
task: ffff880077f9f290 ti: ffff88007a820000 task.ti: ffff88007a820000
RIP: 0010:[<ffffffffa0022bc8>] [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
RSP: 0018:ffff88007a823d08 EFLAGS: 00010202
RAX: 0000000000000008 RBX: ffff8800379a4430 RCX: 0000000000000026
RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff8800379a4430
RBP: ffff88007a823d18 R08: 00000000ffffffff R09: 000000007a9bc65a
R10: 000000000000028f R11: 0000000000000005 R12: ffff880070123e98
R13: ffff880070123de8 R14: 0000000000000100 R15: ffffc90004888000
FS: 0000000000000000(0000) GS:ffff880079a80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000048 CR3: 000000007029b000 CR4: 00000000001007e0
Stack:
ffff88007a823d58 ffff8800379a4430 ffff88007a823d48 ffffffffa0022c89
0000000000000000 ffff8800379a4430 0000000000000000 0000000000000006
ffff88007a823da8 ffffffffa0023be0 ffff88007a823dd8 ffffffff81076204
Call Trace:
[<ffffffffa0022c89>] giveback+0x69/0xa0 [spi_pxa2xx_platform]
[<ffffffffa0023be0>] pump_transfers+0x710/0x740 [spi_pxa2xx_platform]
[<ffffffff81076204>] ? pick_next_task_fair+0x744/0x830
[<ffffffff81049679>] tasklet_action+0xa9/0xe0
[<ffffffff81049a0e>] __do_softirq+0xee/0x280
[<ffffffff81049bc0>] run_ksoftirqd+0x20/0x40
[<ffffffff810646df>] smpboot_thread_fn+0xff/0x1b0
[<ffffffff810645e0>] ? SyS_setgroups+0x150/0x150
[<ffffffff81060f9d>] kthread+0xcd/0xf0
[<ffffffff81060ed0>] ? kthread_create_on_node+0x180/0x180
[<ffffffff8187a82c>] ret_from_fork+0x7c/0xb0
Fix this by clearing drv_data->cur_chip before we call spi_finalize_current_message().
Reported-by: Martin Oldfield <m@mjoldfield.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The MSIOF controller has DTDL and SYNCDL in SITMDR1 register. So,
this patch adds new properties like the following commit:
d0fb47a523
(spi: fsl-espi: Configure FSL eSPI CSBEF and CSAFT)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the 32-bit FIFO is deeper (64 bytes) than the 8-bit FIFO (16 bytes),
use the 32-bit FIFO when there are at least 32 bits remaining to be
transferred in PIO mode or when the transfer length is 32-bit aligned
in DMA mode.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
A 1-byte burst size is rather inefficient and has been shown to cause
TX issues during testing. Increase the DMA burst size to 4-bytes for
both RX and TX DMA when using the 8-bit FIFO.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The double call to init_completion(&mpc8xxx_spi->done); is not needed
presumably this is a editing mistake only.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently SSP registers are accessed by having an own read and write macros
for each register. For instance read_SSSR(iobase) and write_SSSR(iobase).
In my opinion this hurts readability and requires new macros to be defined
for each new added register. Let's define and use instead common
pxa2xx_spi_read() and pxa2xx_spi_write() accessors.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pass pointer to struct driver_data instead of ioaddr to wait_ssp_rx_stall()
for preparing to register access macro cleanup.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move is_lpss_ssp() tests from functions to caller. Although this aims to
improve readability it also saves a few code bytes on x86.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for Diolan DLN2 USB-SPI adapter.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 5.4.6 for the SPI
master module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the SPI portion of ST's SSC device.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is recommended that the SPFI controller be enabled (i.e. setting
SPFI_EN in SPFI_CONTROL) before TX DMA begins.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of new CONFIG_PM_RUNTIME users have been added recently
in the SPI subsystem.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so
#ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/spi/ (again).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
SH-MSIOF driver is enabled autosuspend API of spi framework.
But autosuspend framework doesn't work during initializing.
So runtime PM lock is added in SH-MSIOF driver initializing.
Fixes: e2a0ba547b (spi: sh-msiof: Convert to spi core auto_runtime_pm framework)
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/spi/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Lots of activity in the devicetree code for v3.18. Most of it is related
to getting all of the overlay support code in place, but there are other
important things in there.
There are a few trivial merge conflicts. They shouldn't give you any
trouble.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device tree
- Removal of the of_allnodes list. This used to be used to iterate over
all the nodes in the device tree, but it is unnecessary because the
same thing can be done by iterating over the list of child pointers.
Getting rid of of_allnodes saves some memory and avoids the
possibility of of_allnodes being sorted differently from the child
lists.
- Support for retrieving original DTB blob via sysfs. Needed by kexec.
- More unittests
- Documentation and minor bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ak0A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Lots of activity in the devicetree code for v3.18. Most of it is
related to getting all of the overlay support code in place, but there
are other important things in there.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device
tree
- Removal of the of_allnodes list. This used to be used to iterate
over all the nodes in the device tree, but it is unnecessary
because the same thing can be done by iterating over the list of
child pointers. Getting rid of of_allnodes saves some memory and
avoids the possibility of of_allnodes being sorted differently from
the child lists.
- Support for retrieving original DTB blob via sysfs. Needed by
kexec.
- More unittests
- Documentation and minor bug fixes"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
of: Delete unnecessary check before calling "of_node_put()"
of: Drop ->next pointer from struct device_node
spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
of: support passing console options with stdout-path
of: add optional options parameter to of_find_node_by_path()
of: Add bindings for chosen node, stdout-path
of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
ARM: dt: fix up PL011 device tree bindings
of: base, fix of_property_read_string_helper kernel-doc
of: remove select of non-existant OF_DEVICE config symbol
spi/of: Add OF notifier handler
spi/of: Create new device registration method and accessors
i2c/of: Add OF_RECONFIG notifier handler
i2c/of: Factor out Devicetree registration code
of/overlay: Add overlay unittests
of/overlay: Introduce DT overlay support
of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
of/reconfig: Always use the same structure for notifiers
of/reconfig: Add debug output for OF_RECONFIG notifiers
of/reconfig: Add empty stubs for the of_reconfig methods
...
Not a huge amount going on this release, mainly new drivers (there's a
couple more waiting that didn't quite make the cut for this release
too):
- An interface for querying if the current transfer is the last in a
message, allowing controllers that need special handling for the
final transfer to use the core message parsing.
- Support for Amlogic Meson SPIFC, Imagination Technologies SFPI, Intel
Quark X1000 and Samsung Exynos 7 controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUh0aVAAoJECTWi3JdVIfQ/eMH/06iz3nPi0/bkv/1bW72QbUf
glk/dT/AAPzoXPdwtxqbiHGdvt0QrarXs0nsQgqmvIA0SQRuTNvncon8UmJ9+N2B
OaCfUByC9C8hYpyc4KB4HxzN/sFx9W+F81JRLCk5+zAmn43Gofas9v2AfAy4iksD
BdIpGbcfn/0gmXqObjqfiWh2W8Sqv13goI4bHCAg5v6m58Zht9IV9vn4TSWAWB34
lq4Htn0QxMBRmzj/9iWqAzdfhZGMP1bABqpJrrGzJAws+TzFqytVXPC4iYID6RVW
u4TvOSKq9fkHkbmgapuhR2E7H4P/kYcwtEIJdT/fcUxeDF4w4s0lYNweh6tdk3I=
=wBDI
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Not a huge amount going on this release, mainly new drivers (there's a
couple more waiting that didn't quite make the cut for this release
too):
- An interface for querying if the current transfer is the last in a
message, allowing controllers that need special handling for the
final transfer to use the core message parsing.
- Support for Amlogic Meson SPIFC, Imagination Technologies SFPI,
Intel Quark X1000 and Samsung Exynos 7 controllers"
* tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (38 commits)
spi/s3c64xx: Remove redundant runtime PM management
spi: fsl-spi: remove unused variable assignment
spi: spi-fsl-spi: Return an error code in fsl_spi_do_one_msg()
spi: core: Do not mangle error code from kthread_run()
spi: fsl-espi: add (un)prepare_transfer_hardware calls to save power if SPI is not in use
spi: fsl-(e)spi: migrate to generic master queueing
spi/txx9: Deletion of an unnecessary check before the function call "clk_disable"
spi: cadence: Fix 3-to-8 mux mode
spi: cadence: Init HW after reading devicetree attributes
spi: meson: Select REGMAP_MMIO
spi: s3c64xx: add support for exynos7 SPI controller
spi: spi-pxa2xx: SPI support for Intel Quark X1000
spi: meson: meson_spifc_setup_speed() can be static
spi: spi-pxa2xx: Add helpers for regiseters' accessing
spi: spi-mxs: Fix mapping from vmalloc-ed buffer to scatter list
spi: atmel: introduce probe deferring
spi: atmel: remove compat for non DT board when requesting dma chan
spi: meson: Add support for Amlogic Meson SPIFC
spi: meson: Add device tree bindings documentation for SPIFC
spi: core: Add spi_transfer_is_last() helper
...
In order to avoid the situation where the kthread is waiting for another
context to make the hardware idle let the message pump know if it's being
called from the worker thread context and if it isn't then defer to the
worker thread instead of idling the hardware immediately. This will ensure
that if this situation happens we block rather than busy waiting.
Signed-off-by: Mark Brown <broonie@kernel.org>
If we are using the standard SPI message pump (which all drivers should be
transitioning over to) then special case the message enqueue and instead of
starting the worker thread to push messages to the hardware do so in the
context of the caller if the controller is idle. This avoids a context
switch in the common case where the controller has a single user in a
single thread, for short PIO transfers there may be no need to context
switch away from the calling context to complete the transfer.
The code is a bit more complex than is desirable in part due to the need
to handle drivers not using the standard queue and in part due to handling
the various combinations of bus locking and asynchronous submission in
interrupt context.
It is still suboptimal since it will still wake the message pump for each
transfer in order to schedule idling of the hardware and if multiple
contexts are using the controller simultaneously a caller may end up
pumping a message for some random other thread rather than for itself,
and if the thread ends up deferring due to another context idling the
hardware then it will just busy wait. It can, however, have the benefit
of aggregating power up and down of the hardware when a caller performs
a series of transfers back to back without any need for the use of
spi_async().
Signed-off-by: Mark Brown <broonie@kernel.org>
cur_msg is updated under the queue lock and holds the message we are
currently processing. Since currently we only ever do removals in the
pump kthread it doesn't matter in what order we do things but we want
to be able to push things out from the submitting thread so pull the
check to see if we're currently handling a message before we check to
see if the queue is idle.
Signed-off-by: Mark Brown <broonie@kernel.org>
Since most devices now do use the standard queue and in order to avoid
initialisation ordering issues being introduced by further refactorings
to improve performance move the initialisation of the queue and the lock
for it to the main master allocation.
Signed-off-by: Mark Brown <broonie@kernel.org>
The device already asks the core to hold a runtime PM reference while it
is active so it is redundant to open code that in the driver itself.
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit c592becbe7 ("spi: fsl-(e)spi: migrate to generic master
queueing") the function fsl_spi_do_one_msg() is not void anymore, so return
an error code to avoid the following buid warning:
drivers/spi/spi-fsl-spi.c: In function 'fsl_spi_do_one_msg':
>> drivers/spi/spi-fsl-spi.c:374:4: warning: 'return' with no value, in function returning non-void [-Wreturn-type]
return;
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kthread_run() could return ERR_PTR(-EINTR) from kthread_create_on_node().
Return the actual error code in spi_init_queue() instead of mangling it to
-ENOMEM.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use (un)prepare_transfer_hardware calls to set fsl-espi to
low-power idle if not in use. Reference manual states:
"The eSPI is in a idle state and consumes minimal power.
The eSPI BRG is not functioning and the input clock is disabled"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Migrates the fsl-(e)spi driver to use the generic master queuing.
Avoids the "master is unqueued, this is deprecated" warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clk_disable() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
In 3-to-8 mux mode for the CS pins we need to set the PERI_SEL bit in the
control register. Currently the driver never sets this bit even when
configured for 3-to-8 mux mode. This patch adds code which sets the bit
during device initialization when necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This will make it possible to use the settings specified in the devicetree
to configure the hardware.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Meson SPIFC driver uses regmap mmio functions and so it must
select REGMAP_MMIO to avoid the following build error:
spi-meson-spifc.c: undefined reference to `devm_regmap_init_mmio_clk'
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Exynos7 SPI controller supports only the auto Selection of
CS toggle mode and Exynos7 SoC includes six SPI controllers.
Add support for these changes in Exynos7 SPI controller driver.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two SPI controllers exported by PCI subsystem for Intel Quark X1000.
The SPI memory mapped I/O registers supported by Quark are different from
the current implementation, and Quark only supports the registers of 'SSCR0',
'SSCR1', 'SSSR', 'SSDR', and 'DDS_RATE'. This patch is to enable the SPI for
Intel Quark X1000.
This piece of work is derived from Dan O'Donovan's initial work for Intel Quark
X1000 SPI enabling.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add OF notifier handler needed for creating/destroying spi devices
according to dynamic runtime changes in the DT live tree. This code is
enabled when CONFIG_OF_DYNAMIC is selected.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: <linux-spi@vger.kernel.org>
Dynamically inserting spi device nodes requires the use of a single
device registration method. Refactor the existing
of_register_spi_devices() to split out the core functionality for a
single device into a separate function; of_register_spi_device(). This
function will be used by the OF_DYNAMIC overlay code to make live
modifications to the tree.
Methods to lookup a device/master using a device node are added
as well, of_find_spi_master_by_node() & of_find_spi_device_by_node().
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely] Split patch into two pieces for clarity
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: <linux-spi@vger.kernel.org>
drivers/spi/spi-meson-spifc.c:171:6: sparse: symbol 'meson_spifc_setup_speed' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several registers for SPI, and the registers of 'SSCR0' and 'SSCR1'
are accessed frequently. This path is to introduce helper functions to
simplify the accessing of 'SSCR0' and 'SSCR1'.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can only use page_address on memory that has been mapped using kmap,
when the buffer passed to the SPI has been allocated by vmalloc the page
has not necessarily been mapped through kmap. This means sometimes
page_address will return NULL causing the pointer we pass to sg_init_one
to be invalid. Currently, this issue doesn't show up on the MXS
architecture as the defconfig defines CONFIG_HIGHMEM=n which means all
pages are mapped. For the sake of robustness though it is best to
correct the issue.
As we only call page_address so that we can pass a virtual address to
sg_init_one which will eventually call virt_to_page on it, fix this
by calling sg_set_page directly rather then relying on the sg_init_one
helper.
Note this patch is only build tested as I don't have an MXS system to
test on.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return probe defer if requesting a dma channel without a dma controller
probed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All boards with a dma controller have DT support so using
dma_request_slave_channel_compat is no more needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a driver for the Amlogic Meson SPIFC (SPI flash controller),
which is one of the two SPI controllers available on the SoC. It
doesn't support DMA and has a 64-byte unified transmit/receive buffer.
The device is optimized for interfacing with SPI NOR memories and
allows the execution of standard operations such as read, page
program, sector erase, etc. in a simplified way, toggling a bit in a
dedicated register. The driver doesn't use those predefined commands
and relies only on custom transfers.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On CPM1, when the SPI parameter RAM is relocated to somewhere else than the
default location, in accordance with freescale documentation
(refer micropatch SPI application note EB662), init RX/TX params command shall
not be used because it doesn't take into account the new location, and
overwrites data that is in original location of SPI param ram at addresses
SCC2 param base + (u32*)0x88 (u16*)0x90 (u32*)0x98 (u16*)0xA0, hence breaking
activity on SCC2 if SCC2 is used in a mode like QMC for instance.
Therefore, the action shall be done manually as described by freescale and as
was already partly done by the driver.
Reported-by: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
in SPI boot mode, romcode uses SPI controller to fetch data from NOR
flash. Here we need to reset the hardware IP to restore its state.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
if spi device has no frequency, spi core will setup the default frequency
to max_speed_hz of spi_master according to
int spi_setup(struct spi_device *spi)
{
...
if (!spi->max_speed_hz)
spi->max_speed_hz = spi->master->max_speed_hz;
...
}
this patch moves CSR SiRFSoC SPI frequency set to follow SPI core behaviour.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 8c328a262f ("spi: sirf: Avoid duplicate code in various
bits_per_word cases") is wrong in setting data width register of
fifo is not right, it should use sspi->word_width >> 1 to set
related bits. According to hardware spec, the mapping between
register value and data width:
0 - byte
1 - WORD
2 - DWORD
Fixes: 8c328a262f ("spi: sirf: Avoid duplicate code in various bits_per_word cases") is wrong in setting data width register of
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add support for the Synchronous Peripheral Flash Interface (SPFI) master
controller found on IMG SoCs. The SPFI controller supports 5 chip-select
lines and single/dual/quad mode SPI transfers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can only use page_address on memory that has been mapped using kmap,
when the buffer passed to the SPI has been allocated by vmalloc the page
has not necessarily been mapped through kmap. This means sometimes
page_address will return NULL causing the pointer we pass to sg_set_buf
to be invalid.
As we only call page_address so that we can pass a virtual address to
sg_set_buf which will then immediately call virt_to_page on it, fix this
by calling sg_set_page directly rather then relying on the sg_set_buf
helper.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The call to spi_master_put() in rockchip_spi_remove() is redundant since
the master is registered using devm_. This patch removes it.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently spidev allows callers to set the default speed by overriding the
max_speed_hz in the underlying device. This achieves the immediate goal but
is not what devices expect and can easily lead to userspace trying to set
unsupported speeds and succeeding, apart from anything else drivers can't
set a limit on the speed using max_speed_hz as they'd expect and any other
devices on the bus will be affected.
Instead store the default speed in the spidev struct and fill this in on
each transfer.
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of registering the irq name with the driver name, it's better to pass
the device name so that we have a more explicit indication as to what spi
instance the irq is related:
$ cat /proc/interrupts
CPU0
...
27: 0 - 98 80014000.ssp
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The assignment of SPI_GPIO_NO_CHIPSELECT to cs_gpios[0] causes the following
compiler warning, when building for 64 bit systems:
"warning: overflow in implicit constant conversion [-Woverflow]".
This is because the SPI_GPIO_NO_CHIPSELECT flag is a '-1' type casted to
unsigned long and cs_gpios is of the type int.
Furthermore the chip select's GPIO number is locally stored as unsigned int
and compared with SPI_GPIO_NO_CHIPSELECT. Thus the result of the comparison
is always false, if unsigned long and unsigned int have a different size.
As part of the fix this patch adds a check for the device tree's cs-gpios
property.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An IOCTL call that calls spi_setup() and then dw_spi_setup() will
overwrite the persisted last transfer speed. On each transfer, the
SPI speed is compared to the last transfer speed to determine if the
clock divider registers need to be updated (did the speed change?).
This bug was observed with the spidev driver using spi-config to
update the max transfer speed.
This fix: Don't overwrite the persisted last transaction clock speed
when updating the SPI parameters in dw_spi_setup(). On the next
transaction, the new speed won't match the persisted last speed
and the hardware registers will be updated.
On initialization, the persisted last transaction clock
speed will be 0 but will be updated after the first SPI
transaction.
Move zeroed clock divider check into clock change test because
chip->clk_div is zero on startup and would cause a divide-by-zero
error. The calculation was wrong as well (can't support odd #).
Reported-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If PM_RUNTIME is enabled, it is easy to trigger the following backtrace
on pxa2xx hosts:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104
[<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14)
[<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c)
[<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24)
[<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8)
[<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34)
[<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54)
[<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74)
[<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8)
[<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208)
[<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0)
[<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8)
[<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc)
[<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc)
[<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4)
[<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec)
[<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24)
---[ end trace 46524156d8faa4f6 ]---
This happens because suspend function tries to disable a clock that is
already disabled by runtime_suspend callback. Add if
(!pm_runtime_suspended()) checks to suspend/resume path.
Fixes: 7d94a50585 (spi/pxa2xx: add support for runtime PM)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In order to describe a single slave device that has no chip select line
the 'num-chipselects' property has to be <0> and the 'cs-gpios' property
doesn't need to be set.
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the
lower 2 bits of the chip select to select a CTAR register.
SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values
if the chip selects 4/5 are used. For those chip selects SPI_CTAR even
calculated offsets of non-existing registers.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Currently driver wouldn't work properly if user asked for simplex transfer. The
patch separates DMA rx and tx callbacks and finishes transfer correctly in any
case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch splits few helpers, namely dw_spi_dma_prepare_rx(),
dw_spi_dma_prepare_tx(), and dw_spi_dma_setup() which will be useful for the
consequent improvements.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's possible that the call to of_match_device() (introduced in commit
df59fa7f ["spi: orion: support armada extended baud rates"]) may return
a NULL if there is no match in the device tree (or perhaps no device tree
at all). Check the return pointer and set the local device data to the
lowest common denominator orion device data if it is NULL.
Reported-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To make it cleaner, the system suspend/resume directly call
the runtime suspend/resume functions
and remove the wapper of CONFIG_PM_RUNTIME, CONFIG_PM_SLEEP.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we are using regmap framework's internal locks, so the
lock_arg for dspi_regmap_config is redundant here.
This patch just remove it, and then the dspi_regmap_config could
be const type.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-atmel.c:1518:1-4: WARNING: end returns can be simpified and declaration on line 1514 can be dropped
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of SPI traffic within short period of time.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
In rx mode, dma must be prepared before spi is enabled.
But in tx and tr mode, spi must be enabled first.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because the minimum divisor in rk3x's spi controller is 2,
if spi_clk is less than 2 * sclk_out, we can't get the right divisor.
So we must set spi_clk again to match slave request.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When mapped RX DMA entries are unmapped in an error condition when DMA
is firstly configured in the driver, the number of TX DMA entries was
passed in, which is incorrect
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
By using separate TX and RX bounce buffers, we avoid potential cache
flush and invalidation sequence issue that may be encountered when a
single bounce buffer is shared between TX and RX
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
The of_node element must be initialized to enable discovery of node
children which takes place in the of_register_spi_devices() function.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Though intel-mid-dma does not follow a new DMA workflow (*) let's prepare SPI
DW driver for that.
(*) The client is obliged to call dma_async_issue_pending() which starts the
actual transfers. Old DMA drivers do not follow this, since requirement was
introduced in the discussion of [1].
[1] http://www.spinics.net/lists/arm-kernel/msg125987.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of direct dereference to dmaengine callbacks we are going to use
DMAengine wrappers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using magic numbers in the code we create a bit map definition of
the DMACR register and use it.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Armada SoC family implementation of this SPI hardware module has
extended the configuration register to allow for a wider range of SPI
clock rates. Specifically the Serial Baud Rate Pre-selection bits in the
SPI Interface Configuration Register now also use bits 6 and 7 as well.
Modify the baud rate calculation to handle these differences for the
Armada case. Potentially a baud rate can be setup using a number of
different pre-scalar and scalar combinations. This code tries all
possible pre-scalar divisors (8 in total) to try and find the most
accurate set.
This change introduces (and documents) a new device tree compatible
device name "armada-370-spi" to support this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 46420dd73b (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sort all the include headers alphabetically for the freescale
spi drivers. If the inlcude headers sorted out of order, maybe
the best logical choice is to append new ones after the exist
ones, while this may create a lot of potential for duplicates
and conflicts for each diffenent changes will add new headers
in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mainly to fix missing MODULE_LICENSE.
Also add MODULE_DESCRIPTION and MODULE_AUTHOR.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
config SPI_BCM53XX needs to depend on BCMA_POSSIBLE and select BCMA.
This fixes below build error:
ERROR: "bcma_driver_unregister" [drivers/spi/spi-bcm53xx.ko] undefined!
ERROR: "__bcma_driver_register" [drivers/spi/spi-bcm53xx.ko] undefined!
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In my test on RK3288-pinky board, if spi is enabled, it will begin to
read data from slave regardless of whether the DMA is ready. So we
need prepare DMA before spi is enable.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Remove the probe info message which also has wrong output. No need to add
KERN_INFO to pr_info. Output was:
6Freescale DSPI master initialized
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a extended PL022 which has an extra register for controlling up
to five chip select signals. This controller is found on the AXM5516 SoC.
Unfortunately the PrimeCell identification registers are identical to a
standard ARM PL022. To work around this, the peripheral ID must be overridden
in the device tree using the "arm,primecell-periphid" property with the value
0x000b6022.
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we cannot make sure the 'n' will always be none zero here, and
then if either equal to zero, the kzalloc() will return ZERO_SIZE_PTR,
which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kzalloc().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make comments be surrounded by spaces and move part of code to one line where
it suits 80 characters.
There is no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For testing purposes it's good to have a loopback mode enabled. The patch adds
necessary bits for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Do full clean up at exit, means terminate all ongoing DMA transfers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In case of 8 bit mode and DMA usage we end up with every second byte written as
0. We have to respect bits_per_word settings what this patch actually does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Currently clps711x arch have a fully functional CLK driver.
This patch migrates clps711x-spi driver to use the new CLK subsystem.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously only the ACPI PM domain was supported by the spi bus.
Let's convert to the common attach/detach functions for PM domains,
which currently means we are extending the support to include the
generic PM domain as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently this driver is missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
This patch adds a missing check.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of one port we have 3 ports and all of them can take advantage of
the shared DMA controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
That field has been deprecated in favour of getting the necessary
information from ACPI/DT.
However, we still need to deal systems that are PCI only (no ACPI to back
up). In order to support such systems, we allow the DMA filter function and
its corresponding parameter via pxa2xx_spi_master platform data. Then when
the pxa2xx_spi_dma_setup() doesn't find the channel via ACPI, it falls back
to use the given filter function.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Enable DMA support on i.mx6. The read speed can increase from 600KB/s
to 1.2MB/s on i.mx6q. You can disable or enable dma function in dts.
If not set "dma-names" in dts, spi will use PIO mode. This patch only
validate on i.mx6, not i.mx5, but encourage ones to apply this patch
on i.mx5 since they share the same IP.
Note:
Sometime, there is a weid data in rxfifo after one full tx/rx
transfer finish by DMA on i.mx6dl, so we disable dma functhion on
i.mx6dl.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds ability to configure delay between transmission of
words over SPI bus if it's required by SPI slave devices.
New optional SPI slave property:
- ti,spi-word-delay : delay between transmission of words
(SPIFMTn.WDELAY, SPIDAT1.WDEL)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove empty function davinci_spi_cleanup().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now CS GPIOs are requested from struct spi_master.setup() callback
and that causes failures when Client SPI device is getting accessed
through SPIDEV driver. The failure happens, because .setup() callback
may be called many times from IOCTL handler and when it's called
second time gpio_request() will fail and return -EBUSY.
Hence, fix it by moving CS GPIOs requesting code in .probe().
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since driver is used on other platforms and debugfs stuff would be useful there
as well let's substitute mrst_ by dw_ where it suits. Additionally let's use
SPI master device name when print registers dump.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FSF address is subject to change, thus remove it from the file. While here,
update a copyright line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using that member we prefer to use dma_dev which represents actual
struct device of the DMA device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The support of the Moorestown was removed [1] from kernel long time ago. This
is just a follow up of that change.
[1] http://www.spinics.net/lists/platform-driver-x86/msg02948.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the driver was compiled with DMA support, but DMA channels weren't acquired
by some reason, mid_spi_dma_exit() will crash the kernel.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to keep FSF address in the head of the file. While here, fix
few typos in the header.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The reference manual from Rockchip claims this about the BSF (SPI Busy
Flag):
* 0 - SPI is idle or disabled
* 1 - SPI is actively transferring data
The above doesn't quite appear to be true. Specifically I found the
busy bit set when SPI was disabled. Let's change the WARN_ON() so we
only check the busy bit if the controller was enabled.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wait_for_idle() could get unlucky and timeout too quickly.
Specifically, the old calculation was effectively:
timeout = jiffies + 1;
if (jiffies >= timeout) print warning;
From the above it should be obvious that if jiffies ticks in just the
wrong place then we'll have an effective timeout of 0.
Fix this by effectively changing the above ">=" to a ">". That gives
us an extra jiffy to finish.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
let "#define" statement keep same indentation. the old code layout is
pretty ugly.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
for command mode spi transfer, HW spec requires to do fifo reset work to
clear FIFO status.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
unify 'cmd_transfer' like 'pio_transfer' and 'dma_transfer' as void
function, and also change left_rx_word according to transfer result.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
in spi interrupt handler, we need check RX_IO_DMA status to ensure
rx fifo have received the specify count data.
if not set, the while statement in spi isr function will keep loop,
at last, make the kernel hang.
[The code is actually there in the interrupt handler but apparently it
needs the interrupt unmasking so the handler sees the status -- broonie]
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
the old codes check the cs-gpios, if the gpio number is 0 like:
<&gpio, 0, 0>, the driver will use the only hardware chipselect.
this is wrong because of_spi_register_master() can read property
cs-gpios from device node and set the spi master's cs number and
gpio cs automatically based on whether the cs-gpios is valid.
this patch fixes the beviour of CSR spi driver and move to a core
level supported way.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
Missing a blank line after declarations.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: macros should not use a trailing semicolon
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: else is not generally useful after a break or return
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required
WARNING: min() should probably be min_t(u32, rx_left, dw_readw(dws, DW_SPI_RXFLR))
WARNING: else is not generally useful after a break or return
WARNING: Missing a blank line after declarations
WARNING: void function return statements are not generally useful
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
WARNING: quoted string split across lines
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
WARNING: Prefer kcalloc over kzalloc with multiply
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@kernel.org>
device_add() expects that any memory allocated via devm_* API is only
done in the device's probe function.
Fix below boot warning:
WARNING: CPU: 1 PID: 1 at drivers/base/dd.c:286 driver_probe_device+0x2b4/0x2f4()
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.16.0-10474-g835c90b-dirty #160
[<c0016364>] (unwind_backtrace) from [<c001251c>] (show_stack+0x20/0x24)
[<c001251c>] (show_stack) from [<c04eaefc>] (dump_stack+0x7c/0x98)
[<c04eaefc>] (dump_stack) from [<c0023d4c>] (warn_slowpath_common+0x78/0x9c)
[<c0023d4c>] (warn_slowpath_common) from [<c0023d9c>] (warn_slowpath_null+0x2c/0x34)
[<c0023d9c>] (warn_slowpath_null) from [<c0302c60>] (driver_probe_device+0x2b4/0x2f4)
[<c0302c60>] (driver_probe_device) from [<c0302d90>] (__device_attach+0x50/0x54)
[<c0302d90>] (__device_attach) from [<c0300e60>] (bus_for_each_drv+0x54/0x9c)
[<c0300e60>] (bus_for_each_drv) from [<c0302958>] (device_attach+0x84/0x90)
[<c0302958>] (device_attach) from [<c0301f10>] (bus_probe_device+0x94/0xb8)
[<c0301f10>] (bus_probe_device) from [<c03000c0>] (device_add+0x434/0x4fc)
[<c03000c0>] (device_add) from [<c0342dd4>] (spi_add_device+0x98/0x164)
[<c0342dd4>] (spi_add_device) from [<c03444a4>] (spi_register_master+0x598/0x768)
[<c03444a4>] (spi_register_master) from [<c03446b4>] (devm_spi_register_master+0x40/0x80)
[<c03446b4>] (devm_spi_register_master) from [<c0346214>] (dw_spi_add_host+0x1a8/0x258)
[<c0346214>] (dw_spi_add_host) from [<c0346920>] (dw_spi_mmio_probe+0x1d4/0x294)
[<c0346920>] (dw_spi_mmio_probe) from [<c0304560>] (platform_drv_probe+0x3c/0x6c)
[<c0304560>] (platform_drv_probe) from [<c0302a98>] (driver_probe_device+0xec/0x2f4)
[<c0302a98>] (driver_probe_device) from [<c0302d3c>] (__driver_attach+0x9c/0xa0)
[<c0302d3c>] (__driver_attach) from [<c0300f0c>] (bus_for_each_dev+0x64/0x98)
[<c0300f0c>] (bus_for_each_dev) from [<c0302518>] (driver_attach+0x2c/0x30)
[<c0302518>] (driver_attach) from [<c0302134>] (bus_add_driver+0xdc/0x1f4)
[<c0302134>] (bus_add_driver) from [<c03035c8>] (driver_register+0x88/0x104)
[<c03035c8>] (driver_register) from [<c030445c>] (__platform_driver_register+0x58/0x6c)
[<c030445c>] (__platform_driver_register) from [<c0700f00>] (dw_spi_mmio_driver_init+0x18/0x20)
[<c0700f00>] (dw_spi_mmio_driver_init) from [<c0008914>] (do_one_initcall+0x90/0x1d4)
[<c0008914>] (do_one_initcall) from [<c06d7d90>] (kernel_init_freeable+0x178/0x248)
[<c06d7d90>] (kernel_init_freeable) from [<c04e687c>] (kernel_init+0x18/0xfc)
[<c04e687c>] (kernel_init) from [<c000ecd8>] (ret_from_fork+0x14/0x20)
Reported-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The FSF address is subject to change, thus remove it from the file. While here,
update a copyright line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of checking for device and vendor IDs inside probe function let's
provide a helper function via driver_data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert system PM callbacks to use dev_pm_ops. In addition remove the PCI calls
related to a power state since the bus code cares about this already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Nevertheless pci_bar is 0 let's explicitly use it when map IO regions. While
here, use pci_name instead of dev_name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let's print info message when controller is found and properly initialized.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit dd1053a93f ("spi/drivers: Enable build of drivers with
COMPILE_TEST") allows compile-testing drivers on platforms they're not
meant for.
However, adding "|| COMPILE_TEST" bypasses all other implicit dependencies
assumed by the platform dependencies before, like HAS_DMA.
If NO_DMA=y:
drivers/built-in.o: In function `atmel_spi_dma_unmap_xfer':
drivers/spi/spi-atmel.c:915: undefined reference to `dma_unmap_single'
drivers/spi/spi-atmel.c:918: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_spi_next_xfer_data':
drivers/spi/spi-atmel.c:690: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `atmel_spi_dma_map_xfer':
drivers/spi/spi-atmel.c:890: undefined reference to `dma_map_single'
drivers/spi/spi-atmel.c:893: undefined reference to `dma_mapping_error'
drivers/spi/spi-atmel.c:897: undefined reference to `dma_map_single'
drivers/spi/spi-atmel.c:900: undefined reference to `dma_mapping_error'
drivers/spi/spi-atmel.c:902: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_spi_probe':
drivers/spi/spi-atmel.c:1540: undefined reference to `dma_alloc_coherent'
drivers/spi/spi-atmel.c:1623: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `atmel_spi_remove':
drivers/spi/spi-atmel.c:1665: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ep93xx_spi_dma_finish':
drivers/spi/spi-ep93xx.c:550: undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `ep93xx_spi_dma_prepare':
drivers/spi/spi-ep93xx.c:516: undefined reference to `dma_map_sg'
drivers/spi/spi-ep93xx.c:522: undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `omap2_mcspi_rx_dma':
drivers/spi/spi-omap2-mcspi.c:475: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `omap2_mcspi_txrx_dma':
drivers/spi/spi-omap2-mcspi.c:589: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `omap2_mcspi_transfer_one_message':
drivers/spi/spi-omap2-mcspi.c:1202: undefined reference to `dma_map_single'
drivers/spi/spi-omap2-mcspi.c:1204: undefined reference to `dma_mapping_error'
drivers/spi/spi-omap2-mcspi.c:1211: undefined reference to `dma_map_single'
drivers/spi/spi-omap2-mcspi.c:1213: undefined reference to `dma_mapping_error'
drivers/spi/spi-omap2-mcspi.c:1217: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `tegra_spi_deinit_dma_param':
drivers/spi/spi-tegra114.c:675: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `tegra_spi_copy_spi_rxbuf_to_client_rxbuf':
drivers/spi/spi-tegra114.c:415: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra114.c:440: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_spi_copy_client_txbuf_to_spi_txbuf':
drivers/spi/spi-tegra114.c:381: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra114.c:405: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_spi_start_dma_based_transfer':
drivers/spi/spi-tegra114.c:543: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_slink_deinit_dma_param':
drivers/spi/spi-tegra20-slink.c:705: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `tegra_slink_copy_spi_rxbuf_to_client_rxbuf':
drivers/spi/spi-tegra20-slink.c:427: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra20-slink.c:452: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_slink_copy_client_txbuf_to_spi_txbuf':
drivers/spi/spi-tegra20-slink.c:393: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra20-slink.c:417: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_slink_start_dma_based_transfer':
drivers/spi/spi-tegra20-slink.c:561: undefined reference to `dma_sync_single_for_cpu'
Add dependencies on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make local symbol static, because this is used only in this file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If our client is requesting a clock that is above the maximum clock
then the following division will result in 0:
rs->max_freq / rs->speed
We'll then program 0 into the SPI_BAUDR register. The Rockchip TRM
says: "If the value is 0, the serial output clock (sclk_out) is
disabled."
It's much better to end up with the fastest possible clock rather than
a clock that is off, so enforce a minimum value.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for MSIOF in:
- r8a7792 (R-Car V2H)
- r8a7793 (R-Car M2-N)
- r8a7794 (R-Car E2)
r8a7791 is now called "R-Car M2-W".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for QSPI in:
- r8a7792 (R-Car V2H)
- r8a7793 (R-Car M2-N)
- r8a7794 (R-Car E2)
r8a7791 is now called "R-Car M2-W".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The obvious fix after the commit d9c73bb8a3 "spi: dw: add support for gpio
controlled chip select". This patch fixes the issue by using locally defined
temporary variable.
Fixes: d9c73bb8a3 (spi: dw: add support for gpio controlled chip select)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org>
The commit 04f421e7 "spi: dw: use managed resources" changes drivers to use
managed functions, but seems wasn't properly tested in PCI case. The regs field
of struct dw_spi left uninitialized. Thus, kernel crashes when tries to access
to the SPI controller registers. This patch fixes the issue.
Fixes: 04f421e7 (spi: dw: use managed resources)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The driver should not touch CS lines if SPI_NO_CS flag is set.
This patch fixes it as this functionality was broken accidentally
by
commit a88e34ea21 ("spi: davinci: add support to configure gpio cs through dt").
Fixes: a88e34ea21 ("spi: davinci: add support to configure gpio cs through dt")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SPI host controller is the same as used in Baytrail, only the ACPI ID
is different so add this new ID to the list.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Fix a build failure introduced with commit 30670539b8
(spi: au1550: Fix bug in deallocation of memory)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to unset driver data pointer at removal stage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Client drivers such as the ChomeOS EC driver sometimes use transfers with
no buffers and only a delay specified in order to allow a delay after the
assertion of /CS. Rather than require controller drivers handle this noop
case gracefully put checks in the core to ensure that we don't call into
the controller for such transfers.
Reported-by: Addy Ke <addy.ke@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
devices). If board has a serial flash, it's connected over SPI and the
bcma bus includes a SPI controller. Example log from such a board:
bus0: Found chip with id 53010, rev 0x00 and package 0x02
(...)
bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
This patch adds a bcma driver for SPI core, it registers SPI master
controller and "bcm53xxspiflash" SPI device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI PXA2XX core layer has dependency on common clock framework
to obtain information on host supported clock rate. Thus, we
setup the clock device in the PCI glue layer to enable PCI mode
host pass in the clock rate information.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The new Renesas R-Car Gen2 DMA Controller driver (rcar-dmac) requires
explicit configuration of the DMA slave bus width.
Hardcode the DMA transfer size to 4 bytes, as MSIOF DMA is limited to
32-bit words.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The new Renesas R-Car Gen2 DMA Controller driver (rcar-dmac) requires
explicit configuration of the DMA slave bus width.
Hardcode the DMA transfer size to 1 byte for both directions, as that's
the only supported configuration (16-bit DMA support was removed in
commit 9c5de2c175 ("spi: rspi: Remove
unused 16-bit DMA support")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the devm_kasprintf() helper function instead of open coding
error-prone buffer handling and string formatting.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
If dmaengine_prep_slave_sg() or dmaengine_submit() fail, we may leak
unused DMA descriptors.
As per Documentation/dmaengine.txt, once a DMA descriptor has been
obtained, it must be submitted. Hence:
- First prepare and submit all DMA descriptors,
- Prepare the SPI controller for DMA,
- Start DMA by calling dma_async_issue_pending(),
- Make sure to call dmaengine_terminate_all() on all descriptors that
haven't completed.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
If dmaengine_prep_slave_sg() or dmaengine_submit() fail, we may leak
unused DMA descriptors.
As per Documentation/dmaengine.txt, once a DMA descriptor has been
obtained, it must be submitted. Hence:
- First prepare and submit all DMA descriptors,
- Prepare the SPI controller for DMA,
- Start DMA by calling dma_async_issue_pending(),
- Make sure to call dmaengine_terminate_all() on all descriptors that
haven't completed.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unused definition which cause the following warnings
drivers/spi/spi-omap-100k.c:73:0: warning: "WRITE" redefined [enabled by default]
include/linux/fs.h:193:0: note: this is the location of the previous definition
drivers/spi/spi-omap-100k.c:74:0: warning: "READ" redefined [enabled by default]
include/linux/fs.h:192:0: note: this is the location of the previous definition
Signed-off-by: Nick Krause <xerofoiffy@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These are all arguments or fields that got added without updating the
kerneldoc comments.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The spi hangs waiting the completion of omap2_mcspi_rx_callback.
Signed-off-by: Jorge A. Ventura <jorge.araujo.ventura@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT5DYPAAoJEIwa5zzehBx37egQAIiatNiLLqZnfo3rwGADRz/a
POfPovktj68aPcobyzoyhFtToMqGvi9PpysyFTIQD2HJFG+5BtiIAuqtg0875zDe
EpBWgsfugrm0YktJWAtUerj60oAmNPbKfaEm1cOOWuM2lb2mV+QkRrwSTAgsqkT7
927BzMXKKBRPOVLL0RYhoF8EXa0Eg8kCqAHP8fJrzVYkRp+UrZJDnGiUP1XmWJN+
VXQMu5SEjcPMtqT7+tfX455RfREHJfBcJ1ZN/dPF8HMWDwClQG0lyc6hifh1MxwO
8DjIZNkfZeKqgDqVyC17re7pc7p8md5HL8WXbrKpK0A9vQ5bRexbPHxcwJ1T/C2Y
465H+st5XXbuzV1gbMwjK1/ycsH0tCyffckk8Yl/2e1Fs7GgPNbAELtTdl+5vV1Y
xmDXkyo/9WlRM3LQ23IGKwW7VzN86EfWVuShssfro0fO7xDdb4OOYLdQI+4bCG+h
ytQYun1vU32OEyNik5RVNQuZaMrv2c93a3bID4owwuPHPmYOPVUQaqnRX/0E51eA
aHZYbk2GlUOV3Kq5aSS4iyLg1Yj+I9/NeH9U+A4nc+PQ5FlgGToaVSCuYuw4DqbP
AAG+sqQHbkBMvDPobQz/yd1qZbAb4eLhGy11XK1t5S65rApWI55GwNXnvbyxqt8x
wpmxJTASGxcfuZZgKXm7
=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
A quiet release, more bug fixes than anything else. A few things do
stand out though:
- Updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- Support for Rockchip SPI controllers (their first mainline
submission).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u37g
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A quiet release, more bug fixes than anything else. A few things do
stand out though:
- updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- support for Rockchip SPI controllers (their first mainline
submission)"
* tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
spi: davinci: use spi_device.cs_gpio to store gpio cs per spi device
spi: davinci: add support to configure gpio cs through dt
spi/pl022: Explicitly truncate large bitmask
spi/atmel: Fix pointer to int conversion warnings on 64 bit builds
spi: davinci: fix to support more than 2 chip selects
spi: topcliff-pch: don't hardcode PCI slot to get DMA device
spi: orion: fix incorrect handling of cell-index DT property
spi: orion: Fix error return code in orion_spi_probe()
spi/rockchip: fix error return code in rockchip_spi_probe()
spi/rockchip: remove redundant dev_err call in rockchip_spi_probe()
spi/rockchip: remove duplicated include from spi-rockchip.c
ARM: dts: fix the chip select gpios definition in the SPI nodes
spi: s3c64xx: Update binding documentation
spi: s3c64xx: use the generic SPI "cs-gpios" property
spi: s3c64xx: Revert "spi: s3c64xx: Added provision for dedicated cs pin"
spi: atmel: Use dmaengine_prep_slave_sg() API
spi: topcliff-pch: Update error messages for dmaengine_prep_slave_sg() API
spi: sh-msiof: Use correct device for DMA mapping with IOMMU
spi: sh-msiof: Handle dmaengine_prep_slave_single() failures gracefully
spi: rspi: Handle dmaengine_prep_slave_sg() failures gracefully
...
