Some devices can monitor the CEC pin using an interrupt, but you
only want to enable the interrupt if you actually switch to pin
monitoring mode.
So add a new op that is called when pin monitoring needs to be
switched on or off.
Also fix a small bug where the initial CEC pin event was sent
again when calling S_MODE twice with the same CEC_MODE_MONITOR_PIN
mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The firmware timestamp is an unsigned 32-bit value, but we copy it into
a signed 32-bit variable, so we can theoretically get an overflow in
the calculation when the timestamp is between 2038 and 2106.
This changes the temporary variable to time64_t and changes the deprecated
time_to_tm() over to time64_to_tm() accordingly.
There is still an overflow in y2106, but that is a limitation of the
firmware interface, not a kernel problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the test_pattern control and the h/vflip controls.
This makes it possible to switch to more interesting test patterns and to
test control handling in v4l-subdevs.
There are more tpg-related controls that can be added, but this is a good
start.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix small whitespace checkpatch warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
fixes intermittent soft reboot issue with firmware load
increases wait time of reset, as required by HW
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When used as part of a display pipeline, the VSP is stopped and
restarted explicitly by the DU from its suspend and resume handlers.
There is thus no need to stop or restart pipelines in the VSP suspend
and resume handlers, and doing so would cause the hardware to be
left in a misconfigured state.
Ensure that the VSP suspend and resume handlers do not affect DRM-based
pipelines.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It's not clear if the transmit status that is printed when debugging
is enabled is hex or decimal. Add 0x prefix to make this explicit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A 'return' was missing when detecting Arbitration Lost and
calling transmit_done. With the return transmit_done could be
called a second time, confusing the CEC framework. Luckily
the Arbitration Lost condition is very rare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is possible to call STREAMON without the minimum number of
buffers queued. In this case the vb2_queue state will be set to
streaming but the start_streaming vb2_op will not be called.
Later when enough buffers are queued, start_streaming will
be called but vb2_is_streaming will already return true.
Also removed the queue state check in stop_streaming since it's
not valid there either.
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Reviewed-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This change fixes the calculation of B-frames and GOP size by
adopt v4l2 controls with the firmware interface expectations.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fixed two small checkpatch comments]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Note that the inputs for the Composite and S-Video are inverted in
regard to most of the other boards using a cx231xx chip.
Signed-off-by: Romain Reignier <r.reignier@robopec.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate checks.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The pointer h is already initialized to codeclist_top so the second
identical assignment is redundant and can be removed. Cleans up clang
warning:
drivers/media/pci/zoran/videocodec.c:322:21: warning: Value stored to 'h'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Variable mask is being set to 0x80 and then set to this value again
in the following for-loop. Remove the extraneous first setting of mask.
Cleans up clang warning:
drivers/media/pci/pt3/pt3_i2c.c:88:2: warning: Value stored to 'mask'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using the ARRAY_SIZE macro improves the readability of the code. Also,
it is not always useful to use a variable to store this constant
calculated at compile time.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use a more typical logging style.
The current macro hides the gspca_dev argument so add it to the
macro uses instead.
Miscellanea:
o Add missing '\n' terminations to formats
o Realign arguments to open parenthesis
o Remove commented out uses of PDEBUG
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use a more typical kernel logging style.
The current macro hides the gspca_dev argument so add it to the
macro uses instead.
Miscellanea:
o Add missing '\n' terminations to formats
o Realign arguments to open parenthesis
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We free the stk_camera device too early. It's allocate first in probe
and it should be freed last in stk_camera_disconnect().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Here, hdpvr_register_videodev() is responsible for setup and
register a video device. Also defining and initializing a worker.
hdpvr_register_videodev() is calling by hdpvr_probe at last.
So no need to flush any work here.
Unregister v4l2, free buffers and memory. If hdpvr_probe() will fail.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the read-only u8 array buf on the stack at run time but
instead make it static const; makes object code smaller saving over 480
bytes:
Before:
text data bss dec hex filename
33030 65936 192 99158 18356 drivers/media/usb/dvb-usb/cxusb.o
After:
text data bss dec hex filename
32446 66032 192 98670 1816e drivers/media/usb/dvb-usb/cxusb.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When building without CONFIG_GPIOLIB, we get a harmless
warning about an unused variable:
drivers/media/pci/solo6x10/solo6x10-gpio.c: In function 'solo_gpio_init':
drivers/media/pci/solo6x10/solo6x10-gpio.c:165:6: error: unused variable 'ret' [-Werror=unused-variable]
This adds another #ifdef around the declaration.
Fixes: d3202d1981 ("media: solo6x10: export hardware GPIO pins 8:31 to gpiolib interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Acked-by: Anton Sviridenko <anton@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the arrays RegAddr on the stack, instead make them static
const. Makes the object code smaller by over 980 bytes:
Before:
text data bss dec hex filename
64923 304 0 65227 fecb drivers/media/tuners/mxl5005s.o
After:
text data bss dec hex filename
63779 464 0 64243 faf3 drivers/media/tuners/mxl5005s.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use WARN_ON() instead of BUG_ON() to avoid crashing the kernel.
Signed-off-by: Srishti Sharma <srishtishar@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current implementation has to search the list of controls for the
pixel rate control, each time it is set. This can be optimised easily
by storing the ctrl pointer in the CSI/TX object, and referencing that
directly.
While at it, fix up a missing blank line also highlighted in review
comments.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mt9v032_power_on() leaves clk enabled in case of errors,
but it is not expected by its callers.
There is a similar problem in mt9v032_registered().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov7670 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The sub-device for ov7670 is registered by v4l2_async_register_subdev().
So it should be unregistered by v4l2_async_unregister_subdev() instead of
v4l2_device_unregister_subdev().
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Connect voice coil lens to the camera sensor, so that it can be used
by camera applications.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Document dts support of LED/focus.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the missing MAINTAINERS entry for imx274, fix error handling in driver
probe and unregister the correct control handler in driver remove.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When matching and registering a sub-device from a sub-notifier use the
v4l2_device from the root parent notifier. Using the v4l2_dev stored in
the sub-notifier itself is incorrect as it might not be set.
This can be demonstrated by unbinding and rebinding the adv748x driver
and observing that it fails to probe due to the check !v4l2_dev in
v4l2_device_register_subdev().
# echo 4-0070 > /sys/bus/i2c/drivers/adv748x/unbind
# echo 4-0070 > /sys/bus/i2c/drivers/adv748x/bind
adv748x 4-0070: chip found @ 0xe0 revision 2143
adv748x 4-0070: Failed to probe TXA
adv748x: probe of 4-0070 failed with error -22
Looking at the commit which adds sub-notifiers to V4L2 it looks like
this is the intended behavior of the original commit. With this fix the
adv748x can be re-bound and still function properly.
Fixes: 2cab00bb07 ("media: v4l: async: Allow binding notifiers to sub-devices")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Current implementation of __v4l2_async_notifier_parse_fwnode_endpoints()
checks first whether subdev_count >= subdev_max and only then whether
the port being parsed matches the given port index. This triggers an
error in otherwise valid cases of skipping ports that do not match.
Fix this by moving the check below the port index check.
Fixes: 9ca4653121 ("media: v4l: fwnode: Support generic parsing of graph endpoints in a device")
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_async_register_subdev_sensor_common() is only provided when
CONFIG_V4L2_FWNODE is enabled, otherwise we get a link failure:
drivers/media/i2c/et8ek8/et8ek8_driver.o: In function `et8ek8_probe':
et8ek8_driver.c:(.text+0x884): undefined reference to `v4l2_async_register_subdev_sensor_common'
This adds a Kconfig 'select' statement like all the other users of
this interface have.
Fixes: d8932f38c1 ("media: et8ek8: Add support for flash and lens devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov13858 driver depends on the V4L2 fwnode, thus add that to Kconfig.
Fixes: 5fcf092e0c ("[media] ov13858: add support for OV13858 sensor")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit d57ea877af ("media: rc: per-protocol repeat period"), most
IR protocols have a lower keyup timeout. This causes problems on the
ite-cir, which has default IR timeout of 200ms.
Since the IR decoders read the trailing space, with a IR timeout of 200ms,
the last keydown will have at least a delay of 200ms. This is more than
the protocol timeout of e.g. rc-6 (which is 164ms). As a result the last
IR will be interpreted as a new keydown event, and we get two keypresses.
Revert the protocol timeout to 250ms, except for cec which needs a timeout
of 550ms.
Fixes: d57ea877af ("media: rc: per-protocol repeat period")
Cc: <stable@vger.kernel.org> # 4.14
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For the dvb-frontends that are now part of the documentation,
complete the kernel-doc markups, in order for them to be
properly used at the driver's kAPI documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add to the media book the attachment kAPI for the DVB
frontend drivers that have already some kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now, the Kernel checks for kernel_doc format issues.
Weird enough, it didn't get any of those troubles. Shssst!
Well, let's fix it, as a preventive way to avoid having
hundreds of new warnings on some next Linux version.
Tested by adding all files under dvb-frontends that have
"/**" on them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several comments are wrongly tagged as kernel-doc, causing
those warnings:
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'irq'
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'data'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'solo_dev'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'ch'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'qp'
drivers/media/usb/pwc/pwc-dec23.c:652: warning: Cannot understand *
on line 652 - I thought it was a doc line
drivers/media/usb/dvb-usb/cinergyT2-fe.c:40: warning: No description found for parameter 'op'
drivers/media/usb/dvb-usb/friio-fe.c:301: warning: Cannot understand * (reg, val) commad list to initialize this module.
on line 301 - I thought it was a doc line
drivers/media/rc/streamzap.c:201: warning: No description found for parameter 'urb'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'intf'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'id'
drivers/media/rc/streamzap.c:464: warning: No description found for parameter 'interface'
drivers/media/i2c/ov5647.c:432: warning: Cannot understand * @short Subdev core operations registration
on line 432 - I thought it was a doc line
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'd'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'addr'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wlen'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rlen'
drivers/media/platform/vim2m.c:350: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/tua6100.c:34: warning: cannot understand function prototype: 'struct tua6100_priv '
drivers/media/platform/sti/hva/hva-h264.c:140: warning: cannot understand function prototype: 'struct hva_h264_stereo_video_sei '
drivers/media/platform/sti/hva/hva-h264.c:150: warning: Cannot understand * @frame_width: width in pixels of the buffer containing the input frame
on line 150 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:356: warning: Cannot understand * @ slice_size: slice size
on line 356 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:369: warning: Cannot understand * @ bitstream_size: bitstream size
on line 369 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:395: warning: Cannot understand * @seq_info: sequence information buffer
on line 395 - I thought it was a doc line
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fe'
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fw'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'n'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'd'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_i'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_f'
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:83: warning: cannot understand function prototype: 'struct ttusb '
drivers/media/platform/sh_veu.c:277: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/zl10036.c:33: warning: cannot understand function prototype: 'int zl10036_debug; '
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'frequency'
drivers/media/platform/rcar_fdp1.c:1139: warning: No description found for parameter 'priv'
drivers/media/platform/ti-vpe/vpe.c:933: warning: No description found for parameter 'priv'
drivers/media/usb/gspca/ov519.c:36: warning: No description found for parameter 'fmt'
drivers/media/usb/dvb-usb/dib0700_devices.c:3367: warning: No description found for parameter 'adap'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this warning:
drivers/media/i2c/lm3560.c:69: warning: No description found for parameter 'dev'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On kernel-doc, struct declarations should be declared as "struct foo".
Fix the following warnings:
drivers/media/platform/rcar_jpu.c:265: warning: cannot understand function prototype: 'struct jpu_q_data '
drivers/media/platform/rcar_jpu.c:281: warning: cannot understand function prototype: 'struct jpu_ctx '
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this warning:
drivers/media/platform/vsp1/vsp1_dl.c:87: warning: No description found for parameter 'has_chain'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove this warning:
drivers/media/platform/soc_camera/soc_scale_crop.c:309: warning: Cannot understand * @icd - soc-camera device
on line 309 - I thought it was a doc line
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Fix those warnings:
drivers/media/tuners/mt2063.c:1413: warning: No description found for parameter 'f_ref'
drivers/media/tuners/mt2063.c:1413: warning: Excess function parameter 'f_Ref' description in 'MT2063_fLO_FractionalTerm'
drivers/media/tuners/mt2063.c:1476: warning: Excess function parameter 'f_Avoid' description in 'MT2063_CalcLO2Mult'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Solve those warnings:
drivers/media/radio/radio-wl1273.c:1337: warning: No description found for parameter 'radio'
drivers/media/radio/radio-wl1273.c:1337: warning: Excess function parameter 'core' description in 'wl1273_fm_set_tx_power'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this warning:
drivers/media/platform/s3c-camif/camif-core.c:112: warning: No description found for parameter 'vp'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
