If firmware advertises support for TxBF then the
driver has to instruct the firmware accordingly
during runtime. Without this patch connecting to
an AP with beamformer support would yield abysmal
Rx performance.
This has been tested with wmi-tlv and qca6174
while acting as a STA beamformee only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This processes and pushes fw stats to the debug
module (if enabled).
Changing the generic ath10k_wmi_requests_stats()
call to use more stat bits has no effect on older
firmware binaries.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New qca6174 wmi-tlv firmware revisions support
more stat event bits.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The expected parameter is not a single value but a
mask of values.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New qca6174 wmi-tlv firmware supports vdev stats.
This patch adds support for it in the debug
frontend.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't notify host about
self-bss-peer removal until after associated vdev
is deleted. This has been observed with qca6174
WLAN.RM.2.0-00073 firmware.
This patch fixes AP teardown slowdowns and
prevents delays and warnings:
ath10k_pci 0000:00:05.0: failed to remove peer for AP vdev 0: -110
ath10k_pci 0000:00:05.0: removing stale peer xx:xx:xx:xx:xx:xx from vdev_id 0
ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 24
ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 8
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The value was off by one. The error probably has no negative
affect on any upstream firmware, but should be fixed anyway
in case it comes into use in the future.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A bit of general cleanup to make debug messages more useful.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case firmware fails to start the scan, then complete
the start condition and clean up so that driver does not
block on timeout.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* Enable stuck queue detection for iwlmvm
* A few fixes for EBS scan
* Fixes for various failure paths
* Improvements for TDLS Offchannel
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6aXS
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-02-03' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Add support for beamforming
* Enable stuck queue detection for iwlmvm
* A few fixes for EBS scan
* Fixes for various failure paths
* Improvements for TDLS Offchannel
The functions brcmu_pkt_buf_free_skb() and usb_free_urb() test whether
their argument is NULL and then return immediately. Thus the test around
the call is not needed.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The relay_close() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The functions kfree() and release_firmware() were called in a few cases
by the cw1200_load_firmware_cw1200() function during error handling even if
the passed variables contained still a null pointer.
Corresponding implementation details could be improved by adjustments for
jump targets.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only an API consolidation to make things more readable.
Instances of HZ / CONST are replaced by appropriate msecs_to_jiffies().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbe ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Fixes: 1846ac3dbe ("ath5k: Use usleep_range where possible")
Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the transmit rate for the keep-alive frames
as 1M/CCK when the current channel is in the
2GHz band.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chips in the AR9003 family have a second TSF, which
needs to be cleared when putting the card to
sleep.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setting the required configuration in the PCIE
WorkAround register needs to be done after all the
WoW parameters have been set.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch addresses several issues with the
ath9k_hw_wow_enable() routine:
* The usage of set/clr variables is removed. Writing
the required values to registers is cleaner.
* The shift value of 28 for the contention window field
in AR_WOW_PATTERN is incorrect, change it to 27.
* Disabling Keep Alive needs to be done based on the
LINK_CHANGE option. This is done unconditionally now,
fix this.
* The workaround for the D1/D3 issue is required only
for AR9462.
* The bitfield for enabling pattern matching for packets
less than 256 bytes has expanded for new chips, handle
this accordingly.
* General cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the number of user patterns is higher for
newer chips, make sure that this is registered
during initialization.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips like WB222, WB335 support more than
8 user-configurable patterns. This patch adds
support for it by setting up the correct HW
registers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver utilizes a FIFO buffer for RX descriptors. There are four places
in the code where it calculates the number of free slots. Several of those
locations do the calculation incorrectly. To fix these and to prevent future
mistakes, a common inline routine is created.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware and firmware for the RTL8192EE utilize a FIFO list of
descriptors. There were some problems with the initial implementation.
The worst of these failed to detect that the FIFO was becoming full,
which led to the device needing to be power cycled. As this condition
is not relevant to most of the devices supported by rtlwifi, a callback
routine was added to detect this situation. This patch implements the
necessary changes in the pci handler, and the linkage into the appropriate
rtl8192ee routine.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 3.2 revision has a different target BMI
version so it wasn't recognized by ath10k (despite
the chip_id rev being on the supported list
already).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce an optional log level configuration for the existing debugfs fw_dbglog file. It
allows users to configure the desired log level for firmware dbglog messages.
To configure log level as WARN:
echo 0xffffffff 2 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
The values are:
VERBOSE 0
INFO 1
WARN 2
ERR 3
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise ath10k will just checksum everything even if it did not
go through the TCP/IP stack (for example bridged frames). In the worst
case this could mean recreating the checksum for incorrect data.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The command logic shouldn't really care about
arvif structure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ath10k driver sets wrong default key idx that results in
sending unicast frames with multicast key.
The reason for this behavior is that cached broadcast key
is installed for station MAC address on association. After
dot1x completes, unicast key is installed for station
MAC address. Default key idx is set to broadcast key id when
driver tries to send broadcast frame. This causes firmware
to use broadcast key id to transmit unicast frames to stations.
Used TX_USAGE flag to set default key for stations.
Added callback for setting unicast default idx which will be
invoked on every default key idx configuration.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current implementation depends on msm-bus driver which
is not merged into mainline kernel therefore
this code is removed
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Print (at debug level) all cipher and AKM suites
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Print Tx descriptors
Print ring index for all Tx related messages
Sort prefixes: Tx for transmit, TxC for completion, added "D"
for descriptor related prints
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use spinlock, this should not impact Tx as lock is always free
except for de-allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Non-cacheable Tx descriptor for the last fragment of
multi-fragment frame used to be written back twice.
Refactor code to always write non-cacheable descriptor
only once
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the Tx, work around used to force destination index 0
to be used. This is no more necessary, as firmware supports
multiple destinations
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the maximum number of configurable patterns
is chip-specific, use the HW capability instead
of a fixed value for checking if a free pattern
slot is available.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These macros are applicable to pre-AR9003 chips
and the addresses are different for the AR9003
family. Since they are unused anyway, remove them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the number of patterns that can be configured in
the HW is higher for newer chips, store the chip-specific
value in ath9k_hw_wow.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be used to hold the WOW state in
ath9k_hw.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to allocate a new structure and
free it for every user pattern, instead use local
variables.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
