There are reports that 48kHz audio does not work on the WeTek Play 2
(which uses a GXBB SoC), while 44.1kHz audio works fine on the same
board. There are also reports of 48kHz audio working fine on GXL and
GXM SoCs, which are using an (almost) identical AIU (audio controller).
Experimenting has shown that MPLL0 is causing this problem. In the .dts
we have by default:
assigned-clocks = <&clkc CLKID_MPLL0>,
<&clkc CLKID_MPLL1>,
<&clkc CLKID_MPLL2>;
assigned-clock-rates = <294912000>,
<270950400>,
<393216000>;
The MPLL0 rate is divisible by 48kHz without remainder and the MPLL1
rate is divisible by 44.1kHz without remainder. Swapping these two clock
rates "fixes" 48kHz audio but breaks 44.1kHz audio.
Everything looks normal when looking at the info provided by the common
clock framework while playing 48kHz audio (via I2S with mclk-fs = 256):
mpll_prediv 1 1 0 2000000000
mpll0_div 1 1 0 294909641
mpll0 1 1 0 294909641
cts_amclk_sel 1 1 0 294909641
cts_amclk_div 1 1 0 12287902
cts_amclk 1 1 0 12287902
meson-clk-msr however shows that the actual MPLL0 clock is off by more
than 38MHz:
mp0_out 333322917 +/-10416Hz
The rate seen by meson-clk-msr is very close to what we would get when
SDM (the fractional part) was ignored:
(2000000000Hz * 16384) / ((16384 * 6) = 333.33MHz
If SDM was considered the we should get close to:
(2000000000Hz * 16384) / ((16384 * 6) + 12808) = 294.9MHz
Further experimenting shows that HHI_MPLL_CNTL7[15] does not have any
effect on the rate of MPLL0 as seen my meson-clk-msr (regardless of
whether that bit is zero or one the rate is always the same according to
meson-clk-msr). Using HHI_MPLL_CNTL[25] on the other hand as SDM_EN
results in SDM being considered for the rate output by the hardware. The
rate - as seen by meson-clk-msr - matches with what we expect when
SDM_EN is enabled (fractional part is being considered, resulting in a
294.9MHz output) or disable (fractional part being ignored, resulting in
a 333.33MHz output).
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20211031135006.1508796-1-martin.blumenstingl@googlemail.com
Make it possible to build all clk drivers as modules, but default
remains built-in.
No functional changes.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201118191405.36798-1-khilman@baylibre.com
The "mali_0" or "mali_1" clock trees should not be updated while the
clock is running. Enforce this by setting CLK_SET_RATE_GATE on the
"mali_0" and "mali_1" gates. This makes the CCF switch to the "mali_1"
tree when "mali_0" is currently active and vice versa, which is exactly
what the vendor driver does when updating the frequency of the mali
clock.
Also propagate set_rate requests from the gate to the divider and from
the divider to the the mux so the GPU clock frequency can be updated at
runtime (which will be required for GPU DVFS). Don't propagate rate
changes to the mux parents because we don't want to change the MPLL
clocks (these are reserved for audio).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200414195031.224021-2-martin.blumenstingl@googlemail.com
The aiu devices peripheral clocks needs the aiu and aiu_glue clocks to
operate. Reflect this hierarchy in the gxbb clock tree.
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the ACODEC clock gate to the gxl clk controller driver
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The meson-saradc driver manually sets the input clock for
sar_adc_clk_sel. Update the GXBB clock driver (which is used on GXBB,
GXL and GXM) so the rate settings on sar_adc_clk_div are propagated up
to sar_adc_clk_sel which will let the common clock framework select the
best matching parent clock if we want that.
This makes sar_adc_clk_div consistent with the axg-aoclk and g12a-aoclk
drivers, which both also specify CLK_SET_RATE_PARENT.
Fixes: 33d0fcdfe0 ("clk: gxbb: add the SAR ADC clocks and expose them")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (ie. when
all clocks are local to the controller) and use .parent_data otherwise.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This clock controller use the string comparison method to describe parent
relation between the clocks, which is not optimized.
Migrate to the new way by using .parent_hws where possible (ie. when
all clocks are local to the controller) and use .parent_data otherwise.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The documentation says there is an SSEN bit on mpll0 but, after testing
it, no spread spectrum function appears to be enabled by this bit on any
of the MPLLs.
Let's remove it until we know more
Fixes: 1f737ffa13 ("clk: meson: mpll: fix mpll0 fractional part ignored")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
We want the video decoder clocks to always round to closest. While the
muxes are already using CLK_MUX_ROUND_CLOSEST, the corresponding
CLK_DIVIDER_ROUND_CLOSEST was forgotten for the dividers.
Fix this by adding the flag to the two vdec dividers.
Fixes: a565242eb9 ("clk: meson: gxbb: add the video decoder clocks")
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190319102537.2043-1-mjourdan@baylibre.com
The function used to probe the peripheral clock controller of the arm64
amlogic SoCs is mostly the same. We now have 3 of those controllers so
it is time to factorize things a bit.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190201145345.6795-5-jbrunet@baylibre.com
Initially, the meson clock directory only hosted 2 controllers drivers,
for meson8 and gxbb. At the time, both used the same set of clock drivers
so managing the dependencies was not a big concern.
Since this ancient time, entropy did its job, controllers with different
requirement and specific clock drivers have been added. Unfortunately, we
did not do a great job at managing the dependencies between the
controllers and the different clock drivers. Some drivers, such as
clk-phase or vid-pll-div, are compiled even if they are useless on the
target (meson8). As we are adding new controllers, we need to be able to
pick a driver w/o pulling the whole thing.
The patch aims to clean things up by:
* providing a dedicated CONFIG_ for each clock drivers
* allowing clock drivers to be compiled as a modules, if possible
* stating explicitly which drivers are required by each controller.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190201125841.26785-5-jbrunet@baylibre.com
Instead of relying on a fixed name for the xtal clock, claim the
controller input clock trough DT.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190116175435.4990-2-jbrunet@baylibre.com
* clk-fixes:
clk: qcom: qcs404: Fix gpll0_out_main parent
clk: zynqmp: Off by one in zynqmp_is_valid_clock()
clk: mmp: Off by one in mmp_clk_add()
clk: mvebu: Off by one bugs in cp110_of_clk_get()
arm64: dts: qcom: sdm845-mtp: Mark protected gcc clocks
clk: zynqmp: handle fixed factor param query error
clk: qcom: gcc: Fix board clock node name
clk: meson: axg: mark fdiv2 and fdiv3 as critical
clk: meson-gxbb: set fclk_div3 as CLK_IS_CRITICAL
clk: fixed-factor: fix of_node_get-put imbalance
- Fix GXL HDMI Pll fractional bits (from first round)
- Add the Meson8/Meson8b video clocks
- Add clk-input helper and use it for axg-audio clock driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=paYp
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-4.21-2' of https://github.com/BayLibre/clk-meson into clk-meson
Pull more meson clk driver updates from Neil Armstrong:
- Fix GXL HDMI Pll fractional bits (from first round)
- Add the Meson8/Meson8b video clocks
- Add clk-input helper and use it for axg-audio clock driver
* tag 'meson-clk-4.21-2' of https://github.com/BayLibre/clk-meson:
clk: meson: axg-audio: use the clk input helper function
clk: meson: add clk-input helper function
clk: meson: meson8b: add the read-only video clock trees
clk: meson: meson8b: add the fractional divider for vid_pll_dco
clk: meson: meson8b: fix the offset of vid_pll_dco's N value
clk: meson: Fix GXL HDMI PLL fractional bits width
These are missing 'static' so sparse complains:
drivers/clk/meson/vid-pll-div.c:58:26: warning: symbol '_get_table_val' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1585:12: warning: symbol 'gxbb_vid_pll_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1620:12: warning: symbol 'gxbb_vclk_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:1980:12: warning: symbol 'gxbb_cts_parent_names' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:2036:12: warning: symbol 'gxbb_cts_hdmi_tx_parent_names' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The GXL Documentation specifies 12 bits for the Fractional bit field,
bit the last bits have a different purpose that we cannot handle right
now, so update the bitwidth to have correct fractional calculations.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added comment on GXL HHI_HDMI_PLL_CNTL register shift]
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lkml.kernel.org/r/20181121111922.1277-1-narmstrong@baylibre.com
Add the clocks entries used in the video clock path, the clock path
is doubled to permit having different synchronized clocks for different
parts of the video pipeline.
All dividers are flagged with CLK_GET_RATE_NOCACHE, and all gates are flagged
with CLK_IGNORE_UNUSED since they are currently directly handled by the
Meson DRM Driver.
Once the DRM Driver is fully migrated to using the Common Clock Framework
to handle the video clock tree, the CLK_GET_RATE_NOCACHE and CLK_IGNORE_UNUSED
will be dropped.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: http://lkml.kernel.org/r/1541516257-16157-5-git-send-email-narmstrong@baylibre.com
In an attempt to better describe the HDMI PLL, a single DCO clock was
left for GXBB and GXL, but the GXL DCO does not have a pre-multiplier.
This patch adds back a GXL specific HDMI PLL DCO with xtal as parent.
Fixes: 87173557d2 ("clk: meson: clk-pll: remove od parameters")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: http://lkml.kernel.org/r/1541516257-16157-3-git-send-email-narmstrong@baylibre.com
On the Khadas VIM2 (GXM) and LePotato (GXL) board there are problems
with reboot; e.g. a ~60 second delay between issuing reboot and the
board power cycling (and in some OS configurations reboot will fail
and require manual power cycling).
Similar to 'commit c987ac6f1f ("clk:
meson-gxbb: set fclk_div2 as CLK_IS_CRITICAL")' the SCPI Cortex-M4
Co-Processor seems to depend on FCLK_DIV3 being operational.
Until commit 05f814402d ("clk:
meson: add fdiv clock gates"), this clock was modeled and left on by
the bootloader.
We don't have precise documentation about the SCPI Co-Processor and
its clock requirement so we are learning things the hard way.
Marking this clock as critical solves the problem but it should not
be viewed as final solution. Ideally, the SCPI driver should claim
these clocks. We also depends on some clock hand-off mechanism
making its way to CCF, to make sure the clock stays on between its
registration and the SCPI driver probe.
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Putting hard-coded rates inside the parameter tables assumes that
the parent is known and will never change. That's a big assumption
we should not make.
We have everything we need to recalculate the output rate using
the parent rate and the rest of the parameters. Let's do so and
drop the rates from the tables.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Remove od parameters from pll clocks and add post dividers clocks
instead. Some clock, especially the one which feature several ods,
may provide output between those ods. Also, some drivers, such
as the hdmi driver, may require a more detailed control of the
clock dividers, compared to what CCF would perform automatically.
One added benefit of removing ods is that it also greatly reduce the
size of the rate parameter tables.
In the future, we could possibly take the predivider 'n' out of this
driver as well. To do so, we will need to understand the constraints
for the PLL to lock and whether or not it depends on the input clock
rate.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
CLK_GET_RATE_NOCACHE should only be necessary when the registers
controlling the rate of clock may change outside of CCF. On Amlogic,
it should only be the case for the hdmi pll which is directly controlled
by the display driver (WIP to fix this).
The other plls should not require this flag.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the enable the bit of the pll clocks.
These pll clocks may be disabled but we can't model this as an external
gate since the pll needs to lock when enabled.
Adding this bit allows to drop the poke of the first register of PLL.
This will be useful to model the different components of the pll using
generic clocks elements
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
GEN_CLK is able to route several internal clocks to one of the SoC
pads. In the future, even more clocks could be made accessible using
cts_msr_clk - the clock measure block.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
It is actually a lot easier to setup the PLL with carefully chosen rates
than relying on CCF clock propagation for this audio use case.
This way, we can make sure we will always be able to provide the common
audio clock rates, while having the PLL in the optimal operating range.
For this, we stop the rate propagation at the mux picking the
PLL and let it round to the closest matching PLL.
Doing so, we can use the generic divider for the i2s clock.
clk-audio-divider is no longer required. It was a (poor) attempt
to use CCF rate propagation while making sure the PLL rate would
be high enough to work with audio use cases.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The legacy method to access the hhi register space is not longer used.
We can safely drop it now.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
On Amlogic Meson GXBB & GXL platforms, the SCPI Cortex-M4 Co-Processor
seems to be dependent on the FCLK_DIV2 to be operationnal.
The issue occurred since v4.17-rc1 by freezing the kernel boot when
the 'schedutil' cpufreq governor was selected as default :
[ 12.071837] scpi_protocol scpi: SCP Protocol 0.0 Firmware 0.0.0 version
domain-0 init dvfs: 4
[ 12.087757] hctosys: unable to open rtc device (rtc0)
[ 12.087907] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 12.102241] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
But when disabling the MMC driver, the boot finished but cpufreq failed to
change the CPU frequency :
[ 12.153045] cpufreq: __target_index: Failed to change cpu frequency: -5
A bisect between v4.16 and v4.16-rc1 gave
05f814402d ("clk: meson: add fdiv clock gates") to be the first bad commit.
This commit added support for the missing clock gates before the fixed PLL
fixed dividers (FCLK_DIVx) and the clock framework basically disabled
all the unused fixed dividers, thus disabled a critical clock path for
the SCPI Co-Processor.
This patch simply sets the FCLK_DIV2 gate as critical to ensure
nobody can disable it.
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[few corrections in the commit description]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Replace every license notices in drivers/clk/meson by SPDX license
identifiers, as described in license-rules.rst
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the SEL/DIV/GATE for VDEC_1 and VDEC_HEVC.
Signed-off-by: Maxime Jourdan <maxi.jourdan@wanadoo.fr>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Fixes the following warnings:
drivers/clk/meson/meson8b.c:512:19: warning: symbol 'meson8b_mpeg_clk_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:526:19: warning: symbol 'meson8b_clk81' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:540:19: warning: symbol 'meson8b_cpu_in_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:591:19: warning: symbol 'meson8b_cpu_scale_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:608:19: warning: symbol 'meson8b_cpu_scale_out_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:626:19: warning: symbol 'meson8b_cpu_clk' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:392:27: warning: symbol 'gxbb_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:439:27: warning: symbol 'gxl_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:195:27: warning: symbol 'axg_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:248:27: warning: symbol 'axg_hifi_init_regs' was not declared. Should it be static?
drivers/clk/meson/meson8b.c: In function 'meson8b_clkc_probe':
drivers/clk/meson/meson8b.c:1052:14: warning: unused variable 'clk' [-Wunused-variable]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk81 is a composite clock which parents all the peripheral clocks of the
platform. It is a critical clock which is used as provided by the
bootloader. We don't want to change its rate or reparent it, ever.
Remove the CLK_IGNORE_UNUSED on the mux and divider. These clock can't
gate so the flag is useless, and the gate is already critical, so the
clock won't ever be unused.
Remove CLK_SET_RATE_NO_REPARENT from mux, it is useless since the mux is
read-only.
Remove CLK_SET_RATE_PARENT from the gate and divider and use ro_ops for
the divider. A peripheral clock should not try to change the rate of
clk81. Stopping the rate propagation is good way to make sure such request
would be ignored.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fdiv fixed dividers clocks of the fixed_pll can actually gate
independently. We never had an issue so far because these clocks
were provided 'enabled' by the bootloader.
Add these gates to enable/disable the clocks when required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
mpll clocks parent can actually be divided by 1 or 2. So far, this
divider has always been set to 1, so the calculation was correct.
Now that we know it exists, model the tree correctly. If we ever get
a platform where the divider is different, we won't get into trouble
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the frac parameter for the gp0 pll of the axg and gxl.
This allows to achieve rates between the fixed settings provided
by the table.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After testing, it appears that the gxl (and axg) does not require the
special locking/reset loop which was initially added for it.
All the values present in the gxl table can locked with the simple lock
checking loop.
The change switches the gxl and axg gp0 back to the simple lock checking
loop and removes the code no longer required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Poking CNTL first may take the PLL out of reset while we are still
applying the initial settings, including the filter values
initialization. This is the case for the axg and gxl gp0 pll.
Doing this poke last ensures the pll stays in reset while the initial
settings are applied.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On gxbb and axg, try to get the hhi regmap from the parent DT node, which
should be the HHI system controller once the necessary changes have been
made in amlogic's DTs
Until then, if getting regmap through the system controller fails, the
clock controller will fall back to the old way, requesting memory region
directly and then registering the regmap itself.
This should allow a smooth transition to syscon
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The mpll clock is a kind of fractional divider which can gate.
When the RW operation have been added, enable/disable ops have been
mistakenly inserted in this driver. These ops are essentially a
poor copy/paste of the generic gate ops.
This change removes the gate ops from the mpll driver and inserts a
generic gate clock on each mpll divider, simplifying the mpll
driver and reducing code duplication.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson pll driver to use clk_regmap and move meson8b, gxbb and
axg's clock using meson_clk_pll to clk_regmap.
This rework is not just about clk_regmap, there a serious clean-up of
the driver code:
* Add lock and reset field: Previously inferred from the n field.
* Simplify the reset logic: Code seemed to apply reset differently but
in fact it was always the same -> assert reset, apply params,
de-assert reset. The 2 lock checking loops have been kept for now, as
they seem to be necessary.
* Do the sequence of init register pokes only at .init() instead of in
.set_rate(). Redoing the init on every set_rate() is not necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson audio divider driver to use clk_regmap and move gxbb
clock using meson_clk_audio_divider to clk_regmap.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson mpll driver to use clk_regmap and move meson8b, gxbb
and axg clocks using meson_clk_mpll to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_mux to clk_regmap
Also remove a few useless tables in the process
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_divider to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_gate to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This change registers a regmap in meson8b, gxbb and axg controllers.
The clock are still accessing their registers directly through iomem.
Once all clocks handled by these controllers have been move to regmap,
the regmap register will be removed and replaced with a syscon request.
This is needed because other drivers, such as the HDMI driver, need to
access the HHI register region
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Over time things changes in CCF and issues have been fixed in meson
controllers.
Now, clk81 is decently modeled by read-only PLLs, a mux, a divider
and a gate. We can remove the FIXME comments related to clk81.
Also remove the comment about devm_clk_hw_register, as there is
apparently nothing wrong with it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We don't need several loop index variables in the probe function
This is far from being critical but since we are doing a vast
rework of meson clock controllers, now is the time to lower the
entropy a bit
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
There is no remove callbacks in meson's clock controllers and
of_clk_del_provider is never called if of_clk_add_hw_provider has been
executed, introducing a potential memory leak.
Fixing this by the using the devm variant.
In reality, the leak would never happen since these controllers are
never unloaded once in use ... still, this is worth cleaning.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The 'dev' pointer is directly available in gxbb and axg clock
controller, so consistently use it instead of going the through the
'pdev' pointer once in while
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
