1. ioremap must be balanced by an iounmap and failing to do so can
result in a memory leak.
2. Handle return value correctly
Tested (compilation only) with:
- allmodconfig
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unnecessary cmd_busy member from struct
controller. Read command status register instead of using cmd_busy.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that shpchp driver could mis-detect
command failures if the system was under heavy load.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_find is not hotplug safe, so it really doesn't want to be in an
actual hotplug driver either.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Thu, 2006-09-28 at 03:42, Olaf Hering wrote:
> PCI-Express AER implemetation: pcie_portdrv error handler
>
> This patch breaks if CONFIG_PM is not enabled,
> pcie_portdrv_restore_config() will be undefined.
I move the definition of pcie_portdrv_restore_config
out of CONFIG_PM.
Below patch is against 2.6.18-mm1. Could you try it?
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ACPIPnP implementation had the understanding of Linux resource flags very
wrong, resulting in a nonfunctional implementation of DMA resource
allocation.
This was usually not a problem, since almost no on-board PnP devices use ISA
DMA, with the exception of ECP parallel ports. Even with that, parallel port
DMA is preconfigured by the BIOS, so this routine isn't normally called.
Except in the case where somebody does 'rmmod parport_pc; modprobe
parport_pc', where the rmmod case disables the ECP parallel port resources,
and they need to be enabled again to initialize the module. This didn't
work, resulting in a non-printing printer.
The application doing exactly the above to force reprobing of printers is
the YaST printer module. Thus without this fix YaST wedged the printer when
configuring it, and was not able to print a test page.
Reported-by: Ralf Flaxa <rf@suse.de>
Reproduced-by: Jiri Dluhos <jdluhos@suse.cz>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_fixup_video turns into generic code because there are many platforms need this fixup
for embedded VGA as well as x86. The Video BIOS integrates into System BIOS on a machine
has embedded VGA although embedded VGA generally don't have PCI ROM. As a result,
embedded VGA need the way that the sysfs rom points to the Video BIOS of System
RAM (0xC0000). PCI-to-PCI Bridge Architecture specification describes the condition whether
or not PCI ROM forwards VGA compatible memory address. fixup_video suits this specification.
Although the Video ROM generally implements in x86 code regardless of platform, some
application such as X Window System can run this code by dosemu86. Therefore,
pci_fixup_video should turn into generic code.
Signed-off-by: Eiichiro Oiwa <eiichiro.oiwa.nm@hitachi.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__must_check goes on the declaration, not the definition.
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The most recent VIA IRQ quirk changes have broken various VIA devices for
some users. We are not able to add these devices to the blacklist as they
are also available in PCI-card form, and running the quirk on these devices
brings us back to square one (running the VIA quirk on non-VIA boards where
the quirk is not needed).
This patch, based on suggestions from Sergey Vlasov, implements a scheme
similar to but more restrictive than the scheme we had in 2.6.16 and
earlier. It runs the quirk on all VIA hardware, but *only* if a VIA
southbridge was detected on the system.
To further reduce the amount of quirked devices, this patch includes a
change suggested by Linus at http://lkml.org/lkml/2005/9/27/113 This
ensures that devices bound to non-legacy IO-APIC interrupt lines are not
quirked. We have made one change to Linus' suggestion: we do a comparison
of ">15" rather than ">=15", as 15 is still in the legacy interrupt range.
There is still a downside to this patch: if the user inserts a VIA PCI card
into a VIA-based motherboard, in some circumstances the quirk will also run
on the VIA PCI card. This corner case is hard to avoid.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this was spotted by coverity (cid #819). We dereference p_slot
earlier in the function, and i found no way it could become NULL
anywhere.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that system will panic if multiple power
on/off operations are issued to the same slot in parallel. This
problem can be easily reproduced by commands below.
# while true; do echo 1 > power; echo 0 > power; done &
# while true; do echo 1 > power; echo 0 > power; done &
The cause is lack of locking for enable/disable operations. This patch
fixes this problem.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The slot number displayed in info messages would cause a confusion
because those are displayed in several ways (decimal and hex).
Furthermore, those slot number is not same as slot name (directory
name). This patch fixes those improper info messages.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that issuing SHPC command in poll mode
always fails with the following message.
shpchp: Command not completed in 2000 msec
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a typo to make kernel compilable when floppy driver
for Sparc is build.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds profiling support to the sparc architecture. It is a
copy of the sparc64 implementation.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be calling kernel_execve() directly and this
causes module build failures because kernel_execve() is not
exported to modules.
Signed-off-by: David S. Miller <davem@davemloft.net>
For Hummingbird PCI controllers, we should create the root
PCI memory space resource as the full 4GB area, and then
allocate the IOMMU DMA translation window out of there.
The old code just assumed that the IOMMU DMA translation base
to the top of the 4GB area was unusable. This is not true on
many systems such as SB100 and SB150, where the IOMMU DMA
translation window sits at 0xc0000000->0xdfffffff.
So what would happen is that any device mapped by the firmware
at the top section 0xe0000000->0xffffffff would get remapped
by Linux somewhere else leading to all kinds of problems and
boot failures.
While we're here, report more cases of OBP resource assignment
conflicts. The only truly valid ones are ROM resource conflicts.
Signed-off-by: David S. Miller <davem@davemloft.net>
Unused, but still allow the '-s' boot option to be passed
down to init.
Based upon patches by Martin Habets.
Signed-off-by: David S. Miller <davem@davemloft.net>
It would fail the compile due to the newly added error checking testing
a bad macro for a "return value" unless USB_GADGET_DEBUG_FILES was
enabled.
Pointed out by Stephen Hemminger.
Acked-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (47 commits)
USB: Add device id for Sierra Wireless MC8755
USB: cleanup sierra wireless driver a bit
USB: Sierra Wireless driver update
USB: ftdi_sio whitespace fixes
USB-SERIAL:cp2101 Add new device ID
USB/gadget/net2280: handle sysfs errors
usbtouchscreen: fix data reading for ITM touchscreens
UEAGLE: fix ueagle-atm Oops
USB: xpad: dance pad support
USB: input: extract() and implement() are bit field manipulation routines
USB: Memory leak in drivers/usb/serial/airprime.c
USB Storage: unusual_devs.h entry for Sony Ericsson P990i
USB: fix usbatm tiny race
USB: unusual_devs entry for Nokia 6234
USB: mos7840.c: fix a check-after-dereference
USB: ftdi-elan.c: remove dead code
USB: Mitsumi USB FDD 061M: UNUSUAL_DEV multilun fix
USB: fix dereference in drivers/usb/misc/adutux.c
USB: add USB serial mos7720 driver
USB: move trancevibrator.c to the proper usb directory
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Use mmiowb after doorbell ring
IB/ipath: Initialize diagpkt file on device init only
RDMA/amso1100: Fix a NULL dereference in error path
RDMA/amso1100: pci_module_init() conversion
Adds the device id used by the UMTS cards in Lenovo X60s notebooks sold
in Europe.
Signed-off-by: Jan Luebbe <jluebbe@lasnet.de>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This saves over 30 lines and fixes a warning from sparse and allows
debugging to work dynamically like all other usb-serial drivers.
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The largest feature in this patch is that it adds significant throughput
increase to the Sierra driver and adds support for modem status line
control (e.g. the DTR line). This patch also updates the current sierra.c
driver so that it supports both 3-port Sierra devices and 1-port legacy
devices and removes Sierra's references in other related files (Kconfig and
airprime.c).
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds device ID 0xEA61. This is another factory default ID
used by SILabs.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ITM devices seem to report only garbage when not touched. update usbtouchscreen
to do data reading like itmtouch. also fix wrong mask on pressure bits.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The array of attribute passed to sysfs_create_group() must be
NULL-terminated.
The sysfs entries are created before the start of the modem state machine
to avoid to stop it in case of errors in sysfs creation. Also
{destroy,create}_fs_entries are removed as they do nothing.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for dance pads to the xpad driver. Dance pads require the
d-pad to be mapped to four buttons instead of two axes, so that
combinations of up/down and left/right can be hit simultaneously.
Known dance pads are detected, and there is a module parameter added
to default unknown xpad devices to map the d-pad to buttons if this is
desired. (dpad_to_buttons). Minor modifications were made to port the
changes in the original patch to a newer kernel version.
This patch was originally from Dominic Cerquetti originally written
for kernel 2.6.11.4, with minor modifications (API changes for USB,
spelling fixes to the documentation added in the original patch) made
to apply to the current kernel. I have modified Dominic's original
patch per some suggestions from Dmitry Torokhov. (There was nothing
in the patch format description about multiple From: lines, so I
haven't added myself.)
[akpm@osdl.org: cleanups]
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
extract() and implement() have brain damaged attempts to handle 32-bit wide
"fields".
The problem is the index math in the original code didn't clear all the
relevant bits. (offset >> 5) only compensated for 32-bit index. We need
(offset >> 6) if we want to use 64-bit loads.
But it was also wrong in that it tried to use quasi-aligned loads. Ie
"report" was only incremented in multiples of 4 bytes and then the offset
was masked off for values greater than 4 bytes. The right way is to
pretend "report" points at a byte array. And offset is then only minor
adjustment for < 8 bits of offset. "n" (field width) can then be as big as
24 (assuming 32-bit loads) since "offset" will never be bigger than 7.
If someone needs either function to handle more than 24-bits, please
document why - point at a specification or specific USB hid device - in
comments in the code.
extract/implement() are also an eyesore to read. Please banish whoever
wrote it to read CodingStyle 3 times in a row to a classroom full of 1st
graders armed with rubberbands. Or just flame them. Whatever. Globbing
all the code together on two lines does NOT make it faster and is Just
Wrong.
I've tested this patch on j6000 (dual 750Mhz PA-RISC, 32-bit 2.6.12-rc5).
Kyle McMartin tested on c3000 (up 400Mhz PA-RISC, same kernel). "p2-mate"
(Peter De Schrijver?) tested on sb1250 (dual core Mips, broadcom "swarm"
eval board).
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Storage: this patch adds support for Sony Ericsson P990i
Signed-off-by: Jan Mate <mate@fiit.stuba.sk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ia64:
drivers/usb/atm/usbatm.c: In function `usbatm_do_heavy_init':
drivers/usb/atm/usbatm.c:1004: warning: implicit declaration of function `get_current'
drivers/usb/atm/usbatm.c:1004: error: invalid type argument of `->'
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as803) adds an unusual_devs entry for the Nokia 6234
mobile phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an obvious check-after-dereference spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in two of the error cases, dev is still NULL,
and we dereference it. Spotted by coverity (cid#1428, 1429)
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for Moschip 7720 USB dual port usb to serial device.
This driver is originally based on the drivers/usb/io_edgeport.c driver.
Cleaned up and forward ported by me.
Cc: VijayaKumar <vijaykumar@aspirecom.net>
Cc: AjayKumar <ajay@aspirecom.net>
Cc: Gurudeva <gurudev@aspirecom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not a input driver, so it doesn't belong in the input directory.
Cc: Sam Hocevar <sam@zoy.org>
Cc: Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When working on the mcs7830, I noticed the need for a mutex in its
mdio_read/mdio_write functions. A related problem seems to be present
in the asix driver in the respective functions.
This introduces a mutex in the common usbnet driver and uses it
from the two hardware specific drivers.
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds generic support for the ethtool commands get_settings,
set_settings, get_link and nway_reset to usbnet. These are now
implemented using mii functions when a low-level driver supports
mdio_read/mdio_write and does not override the usbnet ethtool
commands with its own.
Currently, this applies to the asix and the mcs7830 drivers.
I have tested it on mcs7830.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver adds support for the DeLOCK USB ethernet adapter
and potentially others based on the MosChip MCS7830 chip.
It is based on the usbnet and asix drivers as well as the
original device driver provided by MosChip, which in turn
was based on the usbnet driver.
It has been tested successfully on an OHCI, but interestingly
there seems to be a problem with the mcs7830 when connected to
the ICH6/EHCI in my thinkpad: it keeps receiving lots of
broken packets in the RX interrupt. The problem goes away when
I'm using an active USB hub, so I assume it's not related to
the device driver, but rather to the hardware.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds missing class_device_create() error check,
and makes notifier return NOTIFY_BAD.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
