A bridge topology with three systems:
+------+ +------+
| A(2) |--| B(1) |
+------+ +------+
\ /
+------+
| C(3) |
+------+
What is supposed to happen:
* bridge with the lowest ID is elected root (for example: B)
* C detects that A->C is higher cost path and puts in blocking state
What happens. Bridge with lowest id (B) is elected correctly as
root and things start out fine initially. But then config BPDU
doesn't get transmitted from A -> C. Because of that
the link from A-C is transistioned to the forwarding state.
The root cause of this is that the configuration messages
is generated with bogus message age, and dropped before
sending.
In the standardmessage_age is supposed to be:
the time since the generation of the Configuration BPDU by
the Root that instigated the generation of this Configuration BPDU.
Reimplement this by recording the timestamp (age + jiffies) when
recording config information. The old code incorrectly used the time
elapsed on the ageing timer which was incorrect.
See also:
https://bugzilla.vyatta.com/show_bug.cgi?id=7164
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver reads PCI subsystem ID from the PCI configuration register while it's
already stored by the PCI subsystem in the 'subsystem_device' field of 'struct
pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
* 'for-linus-core' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (38 commits)
target: Bump version to v4.1.0-rc1-ml
target: remove custom hex2bin() implementation
target: fix typo Assoication -> Association
target: Update QUEUE ALGORITHM MODIFIER control page default
target: ->map_task_SG conversion to ->map_control_SG and ->map_data_SG
target: Follow up core updates from AGrover and HCH (round 4)
target: Eliminate usage of struct se_mem
target: Pass 2nd param of transport_split_cdb by value
target: Enforce 1 page max for control cdb buffer sizes
target: Make all control CDBs scatter-gather
target: Implement Block Device Characteristics VPD page
target: Fix reporting of supported VPD pages
target: Allow for built-in target modules
tcm_fc: Convert to wake_up_process and schedule_timeout_interruptible
tcm_fc: Makefile cleanups
loopback: Fix memory leak in tcm_loop_make_scsi_hba()
loopback: Remove duplicate scsi/scsi_tcq.h include
loopback: off by one in tcm_loop_make_naa_tpg()
target/iblock: Remove unused iblock_dev members
target/iblock: Use request_queue->nr_request for se_device defaults
...
* 'for-3.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: separate out drain_workqueue() from destroy_workqueue()
workqueue: remove cancel_rearming_delayed_work[queue]()
* 'ptrace' of git://git.kernel.org/pub/scm/linux/kernel/git/oleg/misc: (39 commits)
ptrace: do_wait(traced_leader_killed_by_mt_exec) can block forever
ptrace: fix ptrace_signal() && STOP_DEQUEUED interaction
connector: add an event for monitoring process tracers
ptrace: dont send SIGSTOP on auto-attach if PT_SEIZED
ptrace: mv send-SIGSTOP from do_fork() to ptrace_init_task()
ptrace_init_task: initialize child->jobctl explicitly
has_stopped_jobs: s/task_is_stopped/SIGNAL_STOP_STOPPED/
ptrace: make former thread ID available via PTRACE_GETEVENTMSG after PTRACE_EVENT_EXEC stop
ptrace: wait_consider_task: s/same_thread_group/ptrace_reparented/
ptrace: kill real_parent_is_ptracer() in in favor of ptrace_reparented()
ptrace: ptrace_reparented() should check same_thread_group()
redefine thread_group_leader() as exit_signal >= 0
do not change dead_task->exit_signal
kill task_detached()
reparent_leader: check EXIT_DEAD instead of task_detached()
make do_notify_parent() __must_check, update the callers
__ptrace_detach: avoid task_detached(), check do_notify_parent()
kill tracehook_notify_death()
make do_notify_parent() return bool
ptrace: s/tracehook_tracer_task()/ptrace_parent()/
...
* 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
pci/of: Consolidate pci_bus_to_OF_node()
pci/of: Consolidate pci_device_to_OF_node()
x86/devicetree: Use generic PCI <-> OF matching
microblaze/pci: Move the remains of pci_32.c to pci-common.c
microblaze/pci: Remove powermac originated cruft
pci/of: Match PCI devices to OF nodes dynamically
* 'devicetree/next' of git://git.secretlab.ca/git/linux-2.6:
dt: include linux/errno.h in linux/of_address.h
of/address: Add of_find_matching_node_by_address helper
dt: remove extra xsysace platform_driver registration
tty/serial: Add devicetree support for nVidia Tegra serial ports
dt: add empty of_property_read_u32[_array] for non-dt
dt: bindings: move SEC node under new crypto/
dt: add helper function to read u32 arrays
tty/serial: change of_serial to use new of_property_read_u32() api
dt: add 'const' for of_property_read_string parameter **out_string
dt: add helper functions to read u32 and string property values
tty: of_serial: support for 32 bit accesses
dt: document the of_serial bindings
dt/platform: allow device name to be overridden
drivers/amba: create devices from device tree
dt: add of_platform_populate() for creating device from the device tree
dt: Add default match table for bus ids
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/imx: add device tree probe support
spi/imx: copy gpio number passed by platform data into driver private data
spi/imx: use soc name in spi device type naming scheme
spi/imx: merge type SPI_IMX_VER_0_7 into SPI_IMX_VER_0_4
spi/imx: do not use spi_imx2_3 to name SPI_IMX_VER_2_3 function and macro
spi/imx: use mx21 to name SPI_IMX_VER_0_0 function and macro
spi/imx: do not make copy of spi_imx_devtype_data
spi/dw: Add spi number into spi irq desc
spi/tegra: Use engineering names in DT compatible property
spi/fsl_spi: fix CPM spi driver
mach-s3c2410: remove unused spi-gpio.h file
spi: remove obsolete spi-s3c24xx-gpio driver
mach-gta2: remove unused spi-gpio.h include
mach-qt2410: convert to spi_gpio
mach-jive: convert to spi_gpio
spi/pxa2xx: Remove unavailable ssp_type from documentation
spi/bfin_spi: uninline fat queue funcs
spi/bfin_spi: constify pin array
spi/bfin_spi: use structs for accessing hardware regs
spi/topcliff-pch: Support new device ML7223 IOH
...
Fix up trivial conflict in arch/arm/mach-ep93xx/Makefile
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
IB/qib: Defer HCA error events to tasklet
mlx4_core: Bump the driver version to 1.0
RDMA/cxgb4: Use printk_ratelimited() instead of printk_ratelimit()
IB/mlx4: Support PMA counters for IBoE
IB/mlx4: Use flow counters on IBoE ports
IB/pma: Add include file for IBA performance counters definitions
mlx4_core: Add network flow counters
mlx4_core: Fix location of counter index in QP context struct
mlx4_core: Read extended capabilities into the flags field
mlx4_core: Extend capability flags to 64 bits
IB/mlx4: Generate GID change events in IBoE code
IB/core: Add GID change event
RDMA/cma: Don't allow IPoIB port space for IBoE
RDMA: Allow for NULL .modify_device() and .modify_port() methods
IB/qib: Update active link width
IB/qib: Fix potential deadlock with link down interrupt
IB/qib: Add sysfs interface to read free contexts
IB/mthca: Remove unnecessary read of PCI_CAP_ID_EXP
IB/qib: Remove double define
IB/qib: Remove unnecessary read of PCI_CAP_ID_EXP
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1287 commits)
icmp: Fix regression in nexthop resolution during replies.
net: Fix ppc64 BPF JIT dependencies.
acenic: include NET_SKB_PAD headroom to incoming skbs
ixgbe: convert to ndo_fix_features
ixgbe: only enable WoL for magic packet by default
ixgbe: remove ifdef check for non-existent define
ixgbe: Pass staterr instead of re-reading status and error bits from descriptor
ixgbe: Move interrupt related values out of ring and into q_vector
ixgbe: add structure for containing RX/TX rings to q_vector
ixgbe: inline the ixgbe_maybe_stop_tx function
ixgbe: Update ATR to use recorded TX queues instead of CPU for routing
igb: Fix for DH89xxCC near end loopback test
e1000: always call e1000_check_for_link() on e1000_ce4100 MACs.
netxen: add fw version compatibility check
be2net: request native mode each time the card is reset
ipv4: Constrain UFO fragment sizes to multiples of 8 bytes
virtio_net: Fix panic in virtnet_remove
ipv6: make fragment identifications less predictable
ipv6: unshare inetpeers
can: make function can_get_bittiming static
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: Fix in/out emulation
lguest: Fix translation count about wikipedia's cpuid page
lguest: Fix three simple typos in comments
lguest: update comments
lguest: Simplify device initialization.
lguest: don't rewrite vmcall instructions
lguest: remove remaining vmcall
lguest: use a special 1:1 linear pagetable mode until first switch.
lguest: Do not exit on non-fatal errors
* 'stable/drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Have 'passthrough' option instead of XEN_PCIDEV_BACKEND_PASS and XEN_PCIDEV_BACKEND_VPCI
xen/pciback: Remove the DEBUG option.
xen/pciback: Drop two backends, squash and cleanup some code.
xen/pciback: Print out the MSI/MSI-X (PIRQ) values
xen/pciback: Don't setup an fake IRQ handler for SR-IOV devices.
xen: rename pciback module to xen-pciback.
xen/pciback: Fine-grain the spinlocks and fix BUG: scheduling while atomic cases.
xen/pciback: Allocate IRQ handler for device that is shared with guest.
xen/pciback: Disable MSI/MSI-X when reseting a device
xen/pciback: guest SR-IOV support for PV guest
xen/pciback: Register the owner (domain) of the PCI device.
xen/pciback: Cleanup the driver based on checkpatch warnings and errors.
xen/pciback: xen pci backend driver.
xen: tmem: self-ballooning and frontswap-selfshrinking
xen: Add module alias to autoload backend drivers
xen: Populate xenbus device attributes
xen: Add __attribute__((format(printf... where appropriate
xen: prepare tmem shim to handle frontswap
xen: allow enable use of VGA console on dom0
* 'stable/pci.cleanups.v1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Use 'acpi_gsi_to_irq' value unconditionally.
xen/pci: Remove 'xen_allocate_pirq_gsi'.
xen/pci: Retire unnecessary #ifdef CONFIG_ACPI
xen/pci: Move the allocation of IRQs when there are no IOAPIC's to the end
xen/pci: Squash pci_xen_initial_domain and xen_setup_pirqs together.
xen/pci: Use the xen_register_pirq for HVM and initial domain users
xen/pci: In xen_register_pirq bind the GSI to the IRQ after the hypercall.
xen/pci: Provide #ifdef CONFIG_ACPI to easy code squashing.
xen/pci: Update comments and fix empty spaces.
xen/pci: Shuffle code around.
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (49 commits)
xfs: add size update tracepoint to IO completion
xfs: convert AIL cursors to use struct list_head
xfs: remove confusing ail cursor wrapper
xfs: use a cursor for bulk AIL insertion
xfs: failure mapping nfs fh to inode should return ESTALE
xfs: Remove the second parameter to xfs_sb_count()
xfs: remove the dead XFS_DABUF_DEBUG code
xfs: remove leftovers of the old btree tracing code
xfs: remove the dead QUOTADEBUG code
xfs: remove the unused xfs_buf_delwri_sort function
xfs: remove wrappers around b_iodone
xfs: remove wrappers around b_fspriv
xfs: add a proper transaction pointer to struct xfs_buf
xfs: factor out xfs_da_grow_inode_int
xfs: factor out xfs_dir2_leaf_find_stale
xfs: cleanup struct xfs_dir2_free
xfs: reshuffle dir2 headers
xfs: start periodic workers later
Revert "xfs: fix filesystsem freeze race in xfs_trans_alloc"
xfs: remove variables that serve no purpose in xfs_alloc_ag_vextent_exact()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: don't limit active work items
dlm: use workqueue for callbacks
dlm: remove deadlock debug print
dlm: improve rsb searches
dlm: keep lkbs in idr
dlm: fix kmalloc args
dlm: don't do pointless NULL check, use kzalloc and fix order of arguments
dlm: dump address of unknown node
dlm: use vmalloc for hash tables
dlm: show addresses in configfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/hfsplus:
hfsplus: ensure bio requests are not smaller than the hardware sectors
hfsplus: Add additional range check to handle on-disk corruptions
hfsplus: Add error propagation for hfsplus_ext_write_extent_locked
hfsplus: add error checking for hfs_find_init()
hfsplus: lift the 2TB size limit
hfsplus: fix overflow in hfsplus_read_wrapper
hfsplus: fix overflow in hfsplus_get_block
hfsplus: assignments inside `if' condition clean-up
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw:
GFS2: combine duplicated block freeing routines
GFS2: Add S_NOSEC support
GFS2: Automatically adjust glock min hold time
GFS2: Cache dir hash table in a contiguous buffer
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: clarify the volume notification types' doc
UBI: remove dead code
UBI: dump stack when switching to R/O mode
UBI: fix oops in error path
UBI: switch debugging tests knobs to debugfs
UBI: make it possible to use struct ubi_device in debug.h
UBI: prepare debugging stuff to further debugfs conversion
UBI: use debugfs for the extra checks knobs
UBI: change the interface of a debugging check function
* 'linux-next' of git://git.infradead.org/ubifs-2.6: (32 commits)
MAINTAINERS: change e-mail of Adrian Hunter
UBIFS: fix master node recovery
UBIFS: improve power cut emulation testing
UBIFS: rename recovery testing variables
UBIFS: remove custom list of superblocks
UBIFS: stop re-defining UBI operations
UBIFS: switch to I/O helpers
UBIFS: switch to ubifs_leb_write
UBIFS: switch to ubifs_leb_read
UBIFS: introduce more I/O helpers
UBIFS: always print stacktrace when switching to R/O mode
UBIFS: remove unused and unneeded debugging function
UBIFS: add global debugfs knobs
UBIFS: introduce debugfs helpers
UBIFS: re-arrange debugging code a bit
UBIFS: be more informative in failure mode
UBIFS: switch self-check knobs to debugfs
UBIFS: lessen amount of debugging check types
UBIFS: introduce helper functions for debugging checks and tests
UBIFS: amend debugging inode size check function prototype
...
With ib_qib options:
options ib_qib krcvqs=1 pcie_caps=0x51 rcvhdrcnt=4096 singleport=1 ibmtu=4
a run of ib_write_bw -a yields the following:
------------------------------------------------------------------
#bytes #iterations BW peak[MB/sec] BW average[MB/sec]
1048576 5000 2910.64 229.80
------------------------------------------------------------------
The top cpu use in a profile is:
CPU: Intel Architectural Perfmon, speed 2400.15 MHz (estimated)
Counted CPU_CLK_UNHALTED events (Clock cycles when not halted) with a unit mask
of 0x00 (No unit mask) count 1002300
Counted LLC_MISSES events (Last level cache demand requests from this core that
missed the LLC) with a unit mask of 0x41 (No unit mask) count 10000
samples % samples % app name symbol name
15237 29.2642 964 17.1195 ib_qib.ko qib_7322intr
12320 23.6618 1040 18.4692 ib_qib.ko handle_7322_errors
4106 7.8860 0 0 vmlinux vsnprintf
Analysis of the stats, profile, the code, and the annotated profile indicate:
- All of the overflow interrupts (one per packet overflow) are
serviced on CPU0 with no mitigation on the frequency.
- All of the receive interrupts are being serviced by CPU0. (That is
the way truescale.cmds statically allocates the kctx IRQs to CPU)
- The code is spending all of its time servicing QIB_I_C_ERROR
RcvEgrFullErr interrupts on CPU0, starving the packet receive
processing.
- The decode_err routine is very inefficient, using a printf variant
to format a "%s" and continues to loop when the errs mask has been
cleared.
- Both qib_7322intr and handle_7322_errors read pci registers, which
is very inefficient.
The fix does the following:
- Adds a tasklet to service QIB_I_C_ERROR
- Replaces the very inefficient scnprintf() with a memcpy(). A field
is added to qib_hwerror_msgs to save the sizeof("string") at
compile time so that a strlen is not needed during err_decode().
- The most frequent errors (Overflows) are serviced first to exit the
loop as early as possible.
- The loop now exits as soon as the errs mask is clear rather than
fruitlessly looping through the msp array.
With this fix the performance changes to:
------------------------------------------------------------------
#bytes #iterations BW peak[MB/sec] BW average[MB/sec]
1048576 5000 2990.64 2941.35
------------------------------------------------------------------
During testing of the error handling overflow patch, it was determined
that some CPU's were slower when servicing both overflow and receive
interrupts on CPU0 with different MSI interrupt vectors.
This patch adds an option (krcvq01_no_msi) to not use a dedicated MSI
interrupt for kctx's < 2 and to service them on the default interrupt.
For some CPUs, the cost of the interrupt enter/exit is more costly
than then the additional PCI read in the default handler.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently all bio requests are 512 bytes, which may fail for media
whose physical sector size is larger than this. Ensure these
requests are not smaller than the block device logical block size.
BugLink: http://bugs.launchpad.net/bugs/734883
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
'recoff' is read from disk and used for an argument to memcpy, so if
the value read from disk is larger than the page size, it result to
"general protection fault". This patch add additional range check for
the value, so that disk fuzz won't cause such fault.
Signed-off-by: Naohiro Aota <naota@elisp.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
icmp_route_lookup() uses the wrong flow parameters if the reverse
session route lookup isn't used.
So do not commit to the re-decoded flow until we actually make a
final decision to use a real route saved in 'rt2'.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test-case:
void *tfunc(void *arg)
{
execvp("true", NULL);
return NULL;
}
int main(void)
{
int pid;
if (fork()) {
pthread_t t;
kill(getpid(), SIGSTOP);
pthread_create(&t, NULL, tfunc, NULL);
for (;;)
pause();
}
pid = getppid();
assert(ptrace(PTRACE_ATTACH, pid, 0,0) == 0);
while (wait(NULL) > 0)
ptrace(PTRACE_CONT, pid, 0,0);
return 0;
}
It is racy, exit_notify() does __wake_up_parent() too. But in the
likely case it triggers the problem: de_thread() does release_task()
and the old leader goes away without the notification, the tracer
sleeps in do_wait() without children/tracees.
Change de_thread() to do __wake_up_parent(traced_leader->parent).
Since it is already EXIT_DEAD we can do this without ptrace_unlink(),
EXIT_DEAD threads do not exist from do_wait's pov.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
This patch bumps the target core version to v4.1.0-rc1 now that we are
in sync with upstream lio-core-2.6.git/master
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops transport_asciihex_to_binaryhex() in favor of proper
hex2bin usage from include/linux/kernel.h:hex2bin()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Additionally this patch brings proper apply of the designator type.
However, the original code luckily has no bug, because the association
equals to 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the default 'Unrestricted reordering allowed' for SCSI
control mode page QUEUE ALGORITHM MODIFIER on a per se_device basis in
target_modesense_control() following spc4r23. This includes a new
emuluate_rest_reord configfs attribute that currently (only) accepts
zero to signal 'Unrestricted reordering allowed' in control mode page
usage by the backend target device.
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch breaks up the ->map_task_SG() backend call into two seperate
->map_control_SG() and ->map_data_SG() in order to better address
IBLOCK and pSCSI. IBLOCK only allocates bios for ->map_data_SG(), and
pSCSI will allocate a struct request for both cases.
This patch fixes incorrect usage of ->map_task_SG() for all se_cmd descriptors
in transport_generic_new_cmd() by moving the call into it's proper location
directly inside of transport_allocate_data_tasks()
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch contains the squashed version of forth round series cleanups
from Andy and Christoph following the post heavy lifting in the preceeding:
'Eliminate usage of struct se_mem' and 'Make all control CDBs scatter-gather'
changes. This also includes a conversion of target core and the v3.0
mainline fabric modules (loopback and tcm_fc) to use pr_debug and the
CONFIG_DYNAMIC_DEBUG infrastructure!
These have been squashed into this third and final round for v3.1.
target: Remove ifdeffed code in t_g_process_write
target: Remove direct ramdisk code
target: Rename task_sg_num to task_sg_nents
target: Remove custom debug macros for pr_debug. Use pr_err().
target: Remove custom debug macros in mainline fabrics
target: Set WSNZ=1 in block limits VPD. Abort if WRITE_SAME sectors = 0
target: Remove transport do_se_mem_map callback
target: Further simplify transport_free_pages
target: Redo task allocation return value handling
target: Remove extra parentheses
target: change alloc_task call to take *cdb, not *cmd
(nab: Fix bogus struct file assignments in fd_do_readv and fd_do_writev)
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Both backstores and fabrics use arrays of struct scatterlist to describe
data buffers. However TCM used struct se_mems, basically a linked list
of scatterlist entries. We are able to simplify the code by eliminating
this intermediate data structure and just using struct scatterlist[]
throughout.
Also, moved attachment of task to cmd out of transport_generic_get_task
and into allocate_control_task and allocate_data_tasks. The reasoning
is that it's nonintuitive that get_task should automatically add it to
the cmd's task list -- it should just return an allocated, initialized
task. That's all it should do, based on the function's name, so either the
function shouldn't do it, or the name should change to encapsulate the
entire essence of what it does.
(nab: Fix compile warnings in tcm_fc, and make transport_kmap_first_data_page
honor sg->offset for SGLs from contigious memory with TCM_Loop, and
fix control se_cmd descriptor memory leak)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since sectors is not modified, it's more straightforward to do this.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Due to all cdbs' data buffers being referenced by scatterlists, buffers
of more than a page are not contiguous. Instead of handling this in all
control command handlers, we may be able to get away with just limiting
control cdb data buffers to one page. The only control CDBs we handle that
have potentially large data buffers are REPORT LUNS and UNMAP, so if we
didn't want to live with this limitation, they would need to be modified
to walk the pages in the data buffer's sgl.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Previously, some control CDBs did not allocate memory in pages for their
data buffer, but just did a kmalloc. This patch makes all cdbs allocate
pages.
This has the benefit of streamlining some paths that had to behave
differently when we used two allocation methods. The downside is that
all accesses to the data buffer need to kmap it before use, and need to
handle data in page-sized chunks if more than a page is needed for a given
command's data buffer.
Finally, note that cdbs with no data buffers are handled a little
differently. Before, SCSI_NON_DATA_CDBs would not call get_mem at all
(they'd be in the final else in transport_allocate_resources) but now
these will make it into generic_get_mem, but just not allocate any
buffers.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Implement page B1h, Block Device Characteristics, so that we can report
a medium rotation rate of 1 (non-rotating / solid state) if the
is_nonrot device attribute is set; we update the iblock backend to set
this attribute if the underlying Linux block device has its nonrot
flag set.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The current handling of VPD page 00h (Supported VPD Pages) for INQUIRY
commands has a couple of problems:
- The page length field is incorrectly set to 3, so the entry for 86h
(Extended INQUIRY Data) is ignored since it is in the fourth slot.
- Even though the code handles pages B0h and B2h, those pages aren't
mentioned in the Supported VPD Pages list, so eg the Linux SCSI stack
won't actually try to use them.
Fix these problems and make things more robust to avoid future problems
by moving to a table of supported VPD pages, which means that any added
VPD page support will automatically get reported on page 0.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In target_fabric_configfs_init(), we should allow fabric_mod to be NULL,
since THIS_MODULE is NULL for built-in modules. The main method of
using the target code may be as modules, but having everything built-in
is useful eg to be able to do quick testing with "qemu -kernel".
In any case, we shouldn't bomb out fabric registration for a perfectly
valid configuration, so simply drop the check of fabric_mod.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts ft_queue_cmd() to use wake_up_process() and
ft_thread() to use schedule_timeout_interruptible(MAX_SCHEDULE_TIMEOUT)
instead of wait_event_interruptible(). This fixes a potential race with
the wait_event_interruptible() conditional with qobj->queue_cnt in
ft_thread().
This patch also drops the unnecessary set_user_nice(current, -20) in
ft_thread(), and drops extra () around two if (!(acl)) conditionals in
tfc_conf.c.
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
