1
0
mirror of https://github.com/torvalds/linux.git synced 2024-12-24 03:42:52 +00:00
Commit Graph

10966 Commits

Author SHA1 Message Date
George Cherian
07f3cb7c28 usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.

Note from Sarah:

The xHCI 1.0 spec changed how hardware handles short packets.  The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set).  On the second successful status, that warning will be
triggered in the driver.

Software is now supposed to not assume the TD is not completed until it
gets that last successful status.  That means we have a slight race
condition, although it should have little practical impact.  This patch
papers over that issue.

It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable.  This
patch is needed for stable to avoid serious log spam.

This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333d8 "Intel xhci:
Ignore spurious successful event."

The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.

Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
2013-07-25 08:10:02 -07:00
Randy Dunlap
c4d949b76f usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
Fix warning when CONFIG_PCI is not enabled
(from commit 2963657819).

drivers/usb/host/pci-quirks.h: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2013-07-25 08:09:55 -07:00
Olof Johansson
d5c82feb5c usb: xhci: Mark two functions __maybe_unused
Resolves the following build warnings:
drivers/usb/host/xhci.c:332:13: warning: 'xhci_msix_sync_irqs' defined but not used [-Wunused-function]
drivers/usb/host/xhci.c:3901:12: warning: 'xhci_change_max_exit_latency' defined but not used [-Wunused-function]

These functions are not always used, and since they're marked static
they will produce build warnings:
- xhci_msix_sync_irqs is only used with CONFIG_PCI.
- xhci_change_max_exit_latency is a little more complicated with
  dependencies on CONFIG_PM and CONFIG_PM_RUNTIME.

Instead of building a bigger maze of ifdefs in this code, I've just
marked both with __maybe_unused.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2013-07-25 08:09:48 -07:00
Sarah Sharp
203a86613f xhci: Avoid NULL pointer deref when host dies.
When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().

The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL.  The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.

However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory.  xhci_free_dev checks the return value from the generic
xhci_check_args function.  If the return value is -ENODEV, it carries on
trying to free the virtual device.

The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer.  It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.

The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.

See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details.  This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.

This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b4017 "xhci: Don't
submit commands or URBs to halted hosts."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Vincent Thiele <vincentthiele@gmail.com>
Cc: stable@vger.kernel.org
2013-07-25 08:09:23 -07:00
Bjørn Mork
94190301ff usb: option: add TP-LINK MA260
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-23 16:07:51 -07:00
Alexandr \"Sky\" Ivanov
ca24763588 USB: option: add D-Link DWM-152/C1 and DWM-156/C1
Adding support for D-Link DWM-152/C1 and DWM-156/C1 devices.

DWM-152/C1:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=07d1 ProdID=3e01 Rev= 0.00
S:  Product=USB Configuration
S:  SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

DWM-156/C1:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  8 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=07d1 ProdID=3e02 Rev= 0.00
S:  Product=DataCard Device
S:  SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-23 10:59:39 -07:00
Roger Quadros
47a64a13d5 USB: EHCI: Fix resume signalling on remote wakeup
Set the ehci->resuming flag for the port we receive a remote
wakeup on so that resume signalling can be completed.

Without this, the root hub timer will not fire again to check
if the resume was completed and there will be a never-ending wait on
on the port.

This effect is only observed if the HUB IRQ IN does not come after we
have initiated the port resume.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-22 11:35:34 -07:00
Sami Rahman
7681156982 USB: cp210x: add MMB and PI ZigBee USB Device Support
Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB
devices using customized Silicon Labs' CP210x.c USB to UART bridge
drivers with PIDs: 88A4, 88A5.

Signed-off-by: Sami Rahman <sami.rahman@mmbresearch.com>
Tested-by: Sami Rahman <sami.rahman@mmbresearch.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-22 11:34:16 -07:00
Barry Grussling
b579fa52f6 usb: cp210x support SEL C662 Vendor/Device
This patch adds support for the Schweitzer Engineering Laboratories
C662 USB cable based off the CP210x driver.

Signed-off-by: Barry Grussling <barry@grussling.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-22 11:29:26 -07:00
Daniil Bolsun
c38e83b6cc USB: option: append Petatel NP10T device to GSM modems list
This patch was tested on 3.10.1 kernel.

Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.

Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-22 11:29:26 -07:00
Jóhann B. Guðmundsson
58fc90db82 USB: misc: Add Manhattan Hi-Speed USB DVI Converter to sisusbvga
Signed-off-by: Jóhann B. Guðmundsson <johannbg@fedoraproject.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-22 11:29:26 -07:00
Ren Bigcren
e7a6121f49 USB: storage: Add MicroVault Flash Drive to unusual_devs
The device report an error capacity when read_capacity_16().
Using read_capacity_10() can get the correct capacity.

Signed-off-by: Ren Bigcren <bigcren.ren@sonymobile.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-22 11:29:26 -07:00
Luiz Angelo Daros de Luca
90625070c4 usb: serial: cp210x: Add USB ID for Netgear Switches embedded serial adapter
This adds NetGear Managed Switch M4100 series, M5300 series, M7100 series
USB ID (0846:0110) to the cp210x driver. Without this, the serial
adapter is not recognized in Linux. Description was obtained from
an Netgear Eng.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-22 11:29:26 -07:00
Alan Stern
e583d9db99 USB: global suspend and remote wakeup don't mix
The hub driver was recently changed to use "global" suspend for system
suspend transitions on non-SuperSpeed buses.  This means that we don't
suspend devices individually by setting the suspend feature on the
upstream hub port; instead devices all go into suspend automatically
when the root hub stops transmitting packets.  The idea was to save
time and to avoid certain kinds of wakeup races.

Now it turns out that many hubs are buggy; they don't relay wakeup
requests from a downstream port to their upstream port if the
downstream port's suspend feature is not set (depending on the speed
of the downstream port, whether or not the hub is enabled for remote
wakeup, and possibly other factors).

We can't have hubs dropping wakeup requests.  Therefore this patch
goes partway back to the old policy: It sets the suspend feature for a
port if the device attached to that port or any of its descendants is
enabled for wakeup.  People will still be able to benefit from the
time savings if they don't care about wakeup and leave it disabled on
all their devices.

In order to accomplish this, the patch adds a new field to the usb_hub
structure: wakeup_enabled_descendants is a count of how many devices
below a suspended hub are enabled for remote wakeup.  A corresponding
new subroutine determines the number of wakeup-enabled devices at or
below an arbitrary suspended USB device.

This should be applied to the 3.10 stable kernel.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-07-16 15:33:02 -07:00
Ruchika Kharwar
690c70bab1 usb: phy: omap-usb3: fix dpll clock index
Correction of the omap_usb3_dpll_params array when the sys_clk_rate is
20MHz.

Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:05:30 +03:00
Sachin Kamat
24e6bfd9d9 usb: phy: samsung: Fix an error message typo
The error message is common to both clk_get functions. Update it
accordingly.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:05:29 +03:00
Alan Stern
908b961326 usb: gadget: don't fail when DMA isn't present
When CONFIG_HAS_DMA isn't enabled, the UDC core gets build errors:

drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
drivers/built-in.o: In function `usb_gadget_unmap_request':
drivers/usb/gadget/udc-core.c:91: undefined reference to `dma_unmap_sg'
drivers/usb/gadget/udc-core.c:96: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `usb_gadget_map_request':
drivers/usb/gadget/udc-core.c:62: undefined reference to `dma_map_sg'
drivers/usb/gadget/udc-core.c:71: undefined reference to `dma_map_single'
drivers/usb/gadget/udc-core.c:74: undefined reference to `dma_mapping_error'

Prevent this by protecting the DMA API routines with preprocessor tests.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:05:29 +03:00
Geert Uytterhoeven
91f6b84739 usb: gadget: USB_MV_U3D should depend on HAS_DMA
If NO_DMA=y:

drivers/built-in.o: In function `mv_u3d_done':
drivers/usb/gadget/mv_u3d_core.c:206: undefined reference to `dma_pool_free'
drivers/usb/gadget/mv_u3d_core.c:209: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `mv_u3d_build_trb_one':
drivers/usb/gadget/mv_u3d_core.c:311: undefined reference to `dma_pool_alloc'
drivers/built-in.o: In function `mv_u3d_req_to_trb':
drivers/usb/gadget/mv_u3d_core.c:480: undefined reference to `dma_map_single'
drivers/built-in.o: In function `mv_u3d_remove':
drivers/usb/gadget/mv_u3d_core.c:1770: undefined reference to `dma_pool_destroy'
drivers/usb/gadget/mv_u3d_core.c:1773: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `mv_u3d_probe':
drivers/usb/gadget/mv_u3d_core.c:1880: undefined reference to `dma_alloc_coherent'
drivers/usb/gadget/mv_u3d_core.c:1890: undefined reference to `dma_pool_create'
drivers/usb/gadget/mv_u3d_core.c:1984: undefined reference to `dma_pool_destroy'
drivers/usb/gadget/mv_u3d_core.c:1986: undefined reference to `dma_free_coherent'

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:05:28 +03:00
Geert Uytterhoeven
bfcbd02039 usb: gadget: USB_FOTG210_UDC should depend on HAS_DMA
If NO_DMA=y:

drivers/built-in.o: In function `fotg210_start_dma':
drivers/usb/gadget/fotg210-udc.c:354: undefined reference to `dma_map_single'
drivers/usb/gadget/fotg210-udc.c:357: undefined reference to `dma_mapping_error'
drivers/usb/gadget/fotg210-udc.c:362: undefined reference to `dma_sync_single_for_cpu'
drivers/usb/gadget/fotg210-udc.c:376: undefined reference to `dma_unmap_single'

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:05:28 +03:00
Geert Uytterhoeven
4713aec180 usb: gadget: USB_MV_UDC should depend on HAS_DMA
If NO_DMA=y:

drivers/built-in.o: In function `done':
drivers/usb/gadget/mv_udc_core.c:239: undefined reference to `dma_pool_free'
drivers/built-in.o: In function `build_dtd':
drivers/usb/gadget/mv_udc_core.c:371: undefined reference to `dma_pool_alloc'
drivers/built-in.o: In function `udc_prime_status':
drivers/usb/gadget/mv_udc_core.c:1465: undefined reference to `dma_map_single'
drivers/built-in.o: In function `mv_udc_remove':
drivers/usb/gadget/mv_udc_core.c:2087: undefined reference to `dma_pool_destroy'
drivers/usb/gadget/mv_udc_core.c:2090: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `mv_udc_probe':
drivers/usb/gadget/mv_udc_core.c:2190: undefined reference to `dma_alloc_coherent'
drivers/usb/gadget/mv_udc_core.c:2201: undefined reference to `dma_pool_create'
drivers/usb/gadget/mv_udc_core.c:2315: undefined reference to `dma_pool_destroy'
drivers/usb/gadget/mv_udc_core.c:2317: undefined reference to `dma_free_coherent'

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:05:27 +03:00
Geert Uytterhoeven
8744303eef usb: dwc3: USB_DWC3 should depend on HAS_DMA
If NO_DMA=y:

drivers/built-in.o: In function `dwc3_free_one_event_buffer':
drivers/usb/dwc3/core.c:132: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `dwc3_alloc_one_event_buffer':
drivers/usb/dwc3/core.c:154: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
drivers/built-in.o: In function `dwc3_free_trb_pool':
drivers/usb/dwc3/gadget.c:407: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `dwc3_gadget_exit':
drivers/usb/dwc3/gadget.c:2693: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `dwc3_alloc_trb_pool':
drivers/usb/dwc3/gadget.c:391: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `dwc3_gadget_init':
drivers/usb/dwc3/gadget.c:2598: undefined reference to `dma_alloc_coherent'
drivers/usb/dwc3/gadget.c:2667: undefined reference to `dma_free_coherent'
drivers/usb/dwc3/gadget.c:2674: undefined reference to `dma_free_coherent'
drivers/usb/dwc3/gadget.c:2678: undefined reference to `dma_free_coherent'

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:05:27 +03:00
Andrzej Pietrasiewicz
9d140f796f usb: gadget: Kconfig: Fix configfs-based RNDIS function build
USB_CONFIGFS_RNDIS depends on USB_U_RNDIS. Select it.

Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:04:46 +03:00
Kuninori Morimoto
8047806e64 usb: renesas_usbhs: gadget: remove extra check on udc_stop
usb_gadget_ops :: udc_stop might be called with driver = NULL since
511f3c5326
(usb: gadget: udc-core: fix a regression during gadget driver unbinding)

Because of that, 2nd times insmod goes fail.
This patch fixes it up.

Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:01:24 +03:00
Wei Yongjun
5257a6332e usb: gadget: mv_u3d_core: fix to pass correct device identity to free_irq()
free_irq() expects the same device identity that was passed to
corresponding request_irq(), otherwise the IRQ is not freed.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:01:06 +03:00
Ruchika Kharwar
315955d707 usb: dwc3: fix the error returned with usb3_phy failure
When there is an error with the usb3_phy probe or absence, the error returned
is erroneously for usb2_phy.

Cc: <stable@vger.kernel.org>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 13:00:24 +03:00
Huang Rui
1974d494de usb: dwc3: fix wrong bit mask in dwc3_event_type
Per dwc3 2.50a spec, the is_devspec bit is used to distinguish the
Device Endpoint-Specific Event or Device-Specific Event (DEVT). If the
bit is 1, the event is represented Device-Specific Event, then use
[7:1] bits as Device Specific Event to marked the type. It has 7 bits,
and we can see the reserved8_31 variable name which means from 8 to 31
bits marked reserved, actually there are 24 bits not 25 bits between
that. And 1 + 7 + 24 = 32, the event size is 4 byes.

So in dwc3_event_type, the bit mask should be:
is_devspec	[0]		1  bit
type		[7:1]		7  bits
reserved8_31	[31:8]		24 bits

This patch should be backported to kernels as old as 3.2, that contain
the commit 72246da40f "usb: Introduce
DesignWare USB3 DRD Driver".

Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 12:59:56 +03:00
Boris BREZILLON
7628083227 usb: gadget: at91_udc: prepare clk before calling enable
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 12:59:40 +03:00
Yuan-Hsin Chen
88ae742347 usb: gadget: fotg210-udc: remove __init and __exit
Remove __init and __exit from probe() and remove() and
would also fix the section mismatch issue.

Signed-off-by: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 12:59:17 +03:00
Arnd Bergmann
ae40d64b1f usb: gadget: at91_udc: call at91udc_of_init only when needed
This avoids a build error in at91sam9261_9g10_defconfig:

drivers/usb/gadget/at91_udc.c: In function 'at91udc_probe':
drivers/usb/gadget/at91_udc.c:1685:34: warning: 'flags' may be used uninitialized in this
function [-Wmaybe-uninitialized]
  board->vbus_active_low = (flags & OF_GPIO_ACTIVE_LOW) ? 1 : 0;
                                  ^
drivers/usb/gadget/at91_udc.c:1678:21: note: 'flags' was declared here
  enum of_gpio_flags flags;
                     ^

Making the call to at91udc_of_init conditinal also reduces
the object code size without sacrificing build coverage.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 12:58:11 +03:00
Felipe Balbi
cdcedd6981 usb: dwc3: gadget: don't prevent gadget from being probed if we fail
In case we fail our ->udc_start() callback, we
should be ready to accept another modprobe following
the failed one.

We had forgotten to clear dwc->gadget_driver back
to NULL and, because of that, we were preventing
gadget driver modprobe from being retried.

Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-07-15 12:36:35 +03:00
Linus Torvalds
d144746478 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "MIPS updates:

   - All the things that didn't make 3.10.
   - Removes the Windriver PPMC platform.  Nobody will miss it.
   - Remove a workaround from kernel/irq/irqdomain.c which was there
     exclusivly for MIPS.  Patch by Grant Likely.
   - More small improvments for the SEAD 3 platform
   - Improvments on the BMIPS / SMP support for the BCM63xx series.
   - Various cleanups of dead leftovers.
   - Platform support for the Cavium Octeon-based EdgeRouter Lite.

  Two large KVM patchsets didn't make it for this pull request because
  their respective authors are vacationing"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
  MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
  MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
  MIPS: SEAD3: Disable L2 cache on SEAD-3.
  MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
  MIPS: BCM63xx: Add SMP support to prom.c
  MIPS: define write{b,w,l,q}_relaxed
  MIPS: Expose missing pci_io{map,unmap} declarations
  MIPS: Malta: Update GCMP detection.
  Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
  MIPS: APSP: Remove <asm/kspd.h>
  SSB: Kconfig: Amend SSB_EMBEDDED dependencies
  MIPS: microMIPS: Fix improper definition of ISA exception bit.
  MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
  MIPS: Declare emulate_load_store_microMIPS as a static function.
  MIPS: Fix typos and cleanup comment
  MIPS: Cleanup indentation and whitespace
  MIPS: BMIPS: support booting from physical CPU other than 0
  MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
  MIPS: GIC: Fix gic_set_affinity infinite loop
  MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
  ...
2013-07-13 14:52:21 -07:00
Linus Torvalds
858655116b Merge branch 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
 "This series contain:
   - new i2c video drivers: ml86v7667 (video decoder),
                            ths8200 (video encoder)
   - a new video driver for EasyCap cards based on Fushicai USBTV007
   - Improved support for OF and embedded systems, with V4L2 async
     initialization and a better support for clocks
   - API cleanups on the ioctls used by the v4l2 debug tool
   - Lots of cleanups
   - As usual, several driver improvements and new cards additions
   - Revert two changesets that change the minimal symbol rate for
     stv0399, as request by Manu
   - Update MAINTAINERS and other files to point to my new e-mail"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
  MAINTAINERS & ABI: Update to point to my new email
  [media] stb0899: restore minimal rate to 5Mbauds
  [media] exynos4-is: Correct colorspace handling at FIMC-LITE
  [media] exynos4-is: Set valid initial format on FIMC.n subdevs
  [media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
  [media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
  [media] exynos4-is: Set valid initial format at FIMC-LITE
  [media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
  [media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
  [media] Documentation: Update driver's directory in video4linux/fimc.txt
  [media] exynos4-is: Change fimc-is firmware file names
  [media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
  [media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
  [media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
  [media] media: i2c: tvp514x: remove manual setting of subdev name
  [media] media: i2c: tvp7002: remove manual setting of subdev name
  [media] mem2mem: set missing v4l2_dev pointer
  [media] wl128x: add missing struct v4l2_device
  [media] tvp514x: Fix init seqeunce
  [media] saa7134: Fix sparse warnings by adding __user annotation
  ...
2013-07-13 12:09:57 -07:00
Linus Torvalds
6d2fa9e141 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
 "Lots of activity this round on performance improvements in target-core
  while benchmarking the prototype scsi-mq initiator code with
  vhost-scsi fabric ports, along with a number of iscsi/iser-target
  improvements and hardening fixes for exception path cases post v3.10
  merge.

  The highlights include:

   - Make persistent reservations APTPL buffer allocated on-demand, and
     drop per t10_reservation buffer.  (grover)
   - Make virtual LUN=0 a NULLIO device, and skip allocation of NULLIO
     device pages (grover)
   - Add transport_cmd_check_stop write_pending bit to avoid extra
     access of ->t_state_lock is WRITE I/O submission fast-path.  (nab)
   - Drop unnecessary CMD_T_DEV_ACTIVE check from
     transport_lun_remove_cmd to avoid extra access of ->t_state_lock in
     release fast-path.  (nab)
   - Avoid extra t_state_lock access in __target_execute_cmd fast-path
     (nab)
   - Drop unnecessary vhost-scsi wait_for_tasks=true usage +
     ->t_state_lock access in release fast-path.  (nab)
   - Convert vhost-scsi to use modern se_cmd->cmd_kref
     TARGET_SCF_ACK_KREF usage (nab)
   - Add tracepoints for SCSI commands being processed (roland)
   - Refactoring of iscsi-target handling of ISCSI_OP_NOOP +
     ISCSI_OP_TEXT to be transport independent (nab)
   - Add iscsi-target SendTargets=$IQN support for in-band discovery
     (nab)
   - Add iser-target support for in-band discovery (nab + Or)
   - Add iscsi-target demo-mode TPG authentication context support (nab)
   - Fix isert_put_reject payload buffer post (nab)
   - Fix iscsit_add_reject* usage for iser (nab)
   - Fix iscsit_sequence_cmd reject handling for iser (nab)
   - Fix ISCSI_OP_SCSI_TMFUNC handling for iser (nab)
   - Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED (nab)

  The last five iscsi/iser-target items are CC'ed to stable, as they do
  address issues present in v3.10 code.  They are certainly larger than
  I'd like for stable patch set, but are important to ensure proper
  REJECT exception handling in iser-target for 3.10.y"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
  iser-target: Ignore non TEXT + LOGOUT opcodes for discovery
  target: make queue_tm_rsp() return void
  target: remove unused codes from enum tcm_tmrsp_table
  iscsi-target: kstrtou* configfs attribute parameter cleanups
  iscsi-target: Fix tfc_tpg_auth_cit configfs length overflow
  iscsi-target: Fix tfc_tpg_nacl_auth_cit configfs length overflow
  iser-target: Add support for ISCSI_OP_TEXT opcode + payload handling
  iser-target: Rename sense_buf_[dma,len] to pdu_[dma,len]
  iser-target: Add vendor_err debug output
  target: Add (obsolete) checking for PMI/LBA fields in READ CAPACITY(10)
  target: Return correct sense data for IO past the end of a device
  target: Add tracepoints for SCSI commands being processed
  iser-target: Fix session reset bug with RDMA_CM_EVENT_DISCONNECTED
  iscsi-target: Fix ISCSI_OP_SCSI_TMFUNC handling for iser
  iscsi-target: Fix iscsit_sequence_cmd reject handling for iser
  iscsi-target: Fix iscsit_add_reject* usage for iser
  iser-target: Fix isert_put_reject payload buffer post
  iscsi-target: missing kfree() on error path
  iscsi-target: Drop left-over iscsi_conn->bad_hdr
  target: Make core_scsi3_update_and_write_aptpl return sense_reason_t
  ...
2013-07-11 12:57:19 -07:00
Linus Torvalds
3aa78e0cb5 For the 3.11 merge we only have one new MFD driver for the Kontron PLD.
But we also have:
 
 - Support for the TPS659038 PMIC from the palmas driver.
 
 - Intel's Coleto Creek and Avoton SoCs support from the lpc_ich driver.
 
 - RTL8411B support from the rtsx driver.
 
 - More DT support for the Arizona, max8998, twl4030-power and the
   ti_am335x_tsadc drivers.
 
 - The SSBI driver move under MFD.
 
 - A conversion to the devm_* API for most of the MFD drivers.
 
 - The twl4030-power got split from twl-core into its own module.
 
 - A major ti_am335x_adc cleanup, leading to a proper DT support.
 
 - Our regular arizona and wm* updates and cleanups from the Wolfson
   folks.
 
 - A better error handling and initialization, and a regulator subdevice
   addition for the 88pm80x driver.
 
 - A bulk platform_set_drvdata() call removal that's no longer need since
   commit 0998d063.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJR2zCaAAoJEIqAPN1PVmxK29EP/ieZf7Z7z7bg/0lEOvtOzACy
 WoCdSGFu5XcHOnlv0Fl1Rr/1AJFQoh4KugkGnVyrlztYVOFymj5VDdd8B43cxMLt
 7ymK/3crIH7uJuOoeDoDr3glLuo0TGB9f5Kv4ITdVD3/+AuqY4VIAisEDb0aWghW
 +v0I3fYeGdwRv+IqO5wacvddSoLa4rmOhnpbVMB2O1Y/LCm/yHI6tAFx1+AfH7y8
 zMHbGFc+gHg1xupJBCnRel0v8J+KNc02G/B1zNom/avL8b/mNXNI8JFxs3bMA0r8
 NpTHJ49OVPbhBQTA4U+BPoG4nzOiAOj0czf9dkGa5cyR8t4C9mmK+s8QHwepzrSG
 qbhCgTqp4bomB1m0RAO+z4F6BHTpmoChpho2btrwN9ZmhMHQeTWnGjjhEwZngpBq
 F22DC6k5ipV0k4962ZHfZ76v2Vot1gfd6zQ5r+2oHMMfWaKgS4L5efP2/wsU9H58
 BxMm84C7OWbgcTRmNn9jl4L9phBD31wvNANfUeMhLMyshnwPK5ZuUdX/+K2rq6h9
 w26Hg62HtKZFv/TEsCBQqpB6zSZa4u/KZzvwEahllQSQGKxIHaNYGtLGzJj9sCM+
 baT/82DFKuEvKfJpUKSBMznImp4WNGEz+8s2w4m/Ssuf30GN2GHjM9Q4gcHJu2mk
 7fTrsSHWYN+EHVzh1Zb8
 =RqMp
 -----END PGP SIGNATURE-----

Merge tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next

Pull MFD update from Samuel Ortiz:
 "For the 3.11 merge we only have one new MFD driver for the Kontron
  PLD.

  But we also have:
   - Support for the TPS659038 PMIC from the palmas driver.
   - Intel's Coleto Creek and Avoton SoCs support from the lpc_ich
     driver.
   - RTL8411B support from the rtsx driver.
   - More DT support for the Arizona, max8998, twl4030-power and the
     ti_am335x_tsadc drivers.
   - The SSBI driver move under MFD.
   - A conversion to the devm_* API for most of the MFD drivers.
   - The twl4030-power got split from twl-core into its own module.
   - A major ti_am335x_adc cleanup, leading to a proper DT support.
   - Our regular arizona and wm* updates and cleanups from the Wolfson
     folks.
   - A better error handling and initialization, and a regulator
     subdevice addition for the 88pm80x driver.
   - A bulk platform_set_drvdata() call removal that's no longer need
     since commit 0998d06310 ("device-core: Ensure drvdata = NULL when
     no driver is bound")

* tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (102 commits)
  mfd: sec: Provide max_register to regmap
  mfd: wm8994: Remove duplicate check for active JACKDET
  MAINTAINERS: Add include directory to MFD file patterns
  mfd: sec: Remove fields not used since regmap conversion
  watchdog: Kontron PLD watchdog timer driver
  mfd: max8998: Add support for Device Tree
  regulator: max8998: Use arrays for specifying voltages in platform data
  mfd: max8998: Add irq domain support
  regulator: palmas: Add TPS659038 support
  mfd: Kontron PLD mfd driver
  mfd: palmas: Add TPS659038 PMIC support
  mfd: palmas: Add SMPS10_BOOST feature
  mfd: palmas: Check if irq is valid
  mfd: lpc_ich: iTCO_wdt patch for Intel Coleto Creek DeviceIDs
  mfd: twl-core: Change TWL6025 references to TWL6032
  mfd: davinci_voicecodec: Fix build breakage
  mfd: vexpress: Make the driver optional for arm and arm64
  mfd: htc-egpio: Use devm_ioremap_nocache() instead of ioremap_nocache()
  mfd: davinci_voicecodec: Convert to use devm_* APIs
  mfd: twl4030-power: Fix relocking on error
  ...
2013-07-10 11:10:27 -07:00
Joern Engel
b79fafac70 target: make queue_tm_rsp() return void
The return value wasn't checked by any of the callers.  Assuming this is
correct behaviour, we can simplify some code by not bothering to
generate it.

nab: Add srpt_queue_data_in() + srpt_queue_tm_rsp() nops around
     srpt_queue_response() void return

Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2013-07-07 18:36:53 -07:00
Linus Torvalds
74b9272bbe Device tree updates for v3.11
This branch contains the following changes:
 - Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
 - Remove #ifdef from linux/of_platform.h to increase compiler syntax
   coverage
 - Bug fix for address decoding on Bimini and js2x powerpc platforms.
 - miscellaneous binding changes
 
 One note on the above. The binding changes going in from all kinds of
 different trees has gotten rather out of hand. I picked up some during
 this cycle, but even going though my tree isn't a great fit. Ian
 Campbell has prototyped splitting the bindings and .dtb files into a
 separate repository. The plan is to migrate to using that sometime in
 the next few kernel releases which should get rid of a lot of the churn
 on binding docs and .dts files.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJR1fP3AAoJEEFnBt12D9kB3IIP/0Q5ctMespiJ50+ThjGsaR3m
 sUbQkMK46uL/oupXaJT2ybX2PxLN5LpgvO9rPt77hblOoL0+wZt+j9G0pLy1qZQZ
 aHprH9SrpGJv6F0SFbHp/+D/m9vESPv+zwYzL9TvrOALvCD7OSZ7tHLaoF7Y1ADM
 QnZa7pta3Owpu5NsGXaTXLpaZzfXzfWzf4PDzv2FsAIDbtuVJZGJZ7sJVO7Z0r+K
 KCY85uKJ4VOHY0onBVlM6uoCnopOi2XMMkyxYvR28lL2Kiv2b3np46jG3zX1EZH5
 Qxdu85QZn2oio9iaTeYKK8bG9aRIRsXnzCnF2s68n2rQlEtPpWKN9Lj2AS/KJ+Ig
 obFTOFDHmxt1F4GIA0/HIPkDvRd7GTIwgwYYubEMi44E3Mae0N+xzkIRE41vYP7s
 8zaNHbjAjsYjplsvN5gTPxxiU/ta24a5bl7Ont2zmOjAbXCsDajm4NCKZRJ3lb2f
 FHNsS1zHGmqgJ9zt13GQabo/Tp4t3KwTzBirPQsDokRO4eoL6klcS3GCRv82VWC0
 dLnzu92hXcyXgh7mX2sj6sRBSwNygxMn4ZsZJklle38/LynvtrzT72BOZjghS+Vh
 l553uDInjSJ3IBrXnClPoyObcu50cmsBBgsK39FzU+MF9mcCHmkHQiT52zM6ZW3M
 wwY1OfcZk3XaT7akcVu6
 =CndB
 -----END PGP SIGNATURE-----

Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux

Pull device tree updates from Grant Likely:
 "This branch contains the following changes:
   - Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
   - Remove #ifdef from linux/of_platform.h to increase compiler syntax
     coverage
   - Bug fix for address decoding on Bimini and js2x powerpc platforms.
   - miscellaneous binding changes

  One note on the above.  The binding changes going in from all kinds of
  different trees has gotten rather out of hand.  I picked up some
  during this cycle, but even going though my tree isn't a great fit.

  Ian Campbell has prototyped splitting the bindings and .dtb files into
  a separate repository.  The plan is to migrate to using that sometime
  in the next few kernel releases which should get rid of a lot of the
  churn on binding docs and .dts files"

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
  of: Fix address decoding on Bimini and js2x machines
  of: remove CONFIG_OF_DEVICE
  usb: chipidea: depend on CONFIG_OF instead of CONFIG_OF_DEVICE
  of: remove of_platform_driver
  ibmebus: convert of_platform_driver to platform_driver
  driver core: move to_platform_driver to platform_device.h
  mfd: DT bindings for the palmas family MFD
  ARM: dts: omap3-devkit8000: fix NAND memory binding
  of/base: fix typos
  of: remove #ifdef from linux/of_platform.h
2013-07-04 15:51:45 -07:00
Linus Torvalds
80cc38b163 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
 "The usual stuff from trivial tree"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
  treewide: relase -> release
  Documentation/cgroups/memory.txt: fix stat file documentation
  sysctl/net.txt: delete reference to obsolete 2.4.x kernel
  spinlock_api_smp.h: fix preprocessor comments
  treewide: Fix typo in printk
  doc: device tree: clarify stuff in usage-model.txt.
  open firmware: "/aliasas" -> "/aliases"
  md: bcache: Fixed a typo with the word 'arithmetic'
  irq/generic-chip: fix a few kernel-doc entries
  frv: Convert use of typedef ctl_table to struct ctl_table
  sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
  doc: clk: Fix incorrect wording
  Documentation/arm/IXP4xx fix a typo
  Documentation/networking/ieee802154 fix a typo
  Documentation/DocBook/media/v4l fix a typo
  Documentation/video4linux/si476x.txt fix a typo
  Documentation/virtual/kvm/api.txt fix a typo
  Documentation/early-userspace/README fix a typo
  Documentation/video4linux/soc-camera.txt fix a typo
  lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
  ...
2013-07-04 11:40:58 -07:00
Linus Torvalds
7f0ef0267e Merge branch 'akpm' (updates from Andrew Morton)
Merge first patch-bomb from Andrew Morton:
 - various misc bits
 - I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
   distracted.  There has been quite a bit of activity.
 - About half the MM queue
 - Some backlight bits
 - Various lib/ updates
 - checkpatch updates
 - zillions more little rtc patches
 - ptrace
 - signals
 - exec
 - procfs
 - rapidio
 - nbd
 - aoe
 - pps
 - memstick
 - tools/testing/selftests updates

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
  tools/testing/selftests: don't assume the x bit is set on scripts
  selftests: add .gitignore for kcmp
  selftests: fix clean target in kcmp Makefile
  selftests: add .gitignore for vm
  selftests: add hugetlbfstest
  self-test: fix make clean
  selftests: exit 1 on failure
  kernel/resource.c: remove the unneeded assignment in function __find_resource
  aio: fix wrong comment in aio_complete()
  drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
  drivers/memstick/host/r592.c: convert to module_pci_driver
  drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
  pps-gpio: add device-tree binding and support
  drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
  drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
  drivers/parport/share.c: use kzalloc
  Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
  aoe: update internal version number to v83
  aoe: update copyright date
  aoe: perform I/O completions in parallel
  ...
2013-07-03 17:12:13 -07:00
Kees Cook
f170168b9a drivers: avoid parsing names as kthread_run() format strings
Calling kthread_run with a single name parameter causes it to be handled
as a format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:07:41 -07:00
Linus Torvalds
f991fae5c6 Power management and ACPI updates for 3.11-rc1
- Hotplug changes allowing device hot-removal operations to fail
   gracefully (instead of crashing the kernel) if they cannot be
   carried out completely.  From Rafael J Wysocki and Toshi Kani.
 
 - Freezer update from Colin Cross and Mandeep Singh Baines targeted
   at making the freezing of tasks a bit less heavy weight operation.
 
 - cpufreq resume fix from Srivatsa S Bhat for a regression introduced
   during the 3.10 cycle causing some cpufreq sysfs attributes to
   return wrong values to user space after resume.
 
 - New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
   provide information previously available via related_cpus from
   Lan Tianyu.
 
 - cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
   Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
   Tang Yuantian.
 
 - Fix for an ACPICA regression causing suspend/resume issues to
   appear on some systems introduced during the 3.4 development cycle
   from Lv Zheng.
 
 - ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
   Chao Guan, and Zhang Rui.
 
 - New cupidle driver for Xilinx Zynq processors from Michal Simek.
 
 - cpuidle fixes and cleanups from Daniel Lezcano.
 
 - Changes to make suspend/resume work correctly in Xen guests from
   Konrad Rzeszutek Wilk.
 
 - ACPI device power management fixes and cleanups from Fengguang Wu
   and Rafael J Wysocki.
 
 - ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
 
 - Fix for the IA-64 issue that was the reason for reverting commit
   9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
 
 - Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
   (to allow some EC-related breakage to be fixed on some systems).
 
 - Spec-compliant implementation of acpi_os_get_timer() from
   Mika Westerberg.
 
 - Modification of do_acpi_find_child() to execute _STA in order to
   to avoid situations in which a pointer to a disabled device object
   is returned instead of an enabled one with the same _ADR value.
   From Jeff Wu.
 
 - Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
   Intel Low-Power Subsystems (LPSS) driver and modificaions of that
   driver to work around a couple of known BIOS issues from
   Mika Westerberg and Heikki Krogerus.
 
 - EC driver fix from Vasiliy Kulikov to make it use get_user() and
   put_user() instead of dereferencing user space pointers blindly.
 
 - Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
   Toshi Kani.
 
 - Modification of the "runtime idle" helper routine to take the return
   values of the callbacks executed by it into account and to call
   rpm_suspend() if they return 0, which allows some code bloat
   reduction to be done, from Rafael J Wysocki and Alan Stern.
 
 - New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
 
 - PM QoS documentation update from Lan Tianyu.
 
 - Assorted core PM code cleanups and changes from Bernie Thompson,
   Bjorn Helgaas, Julius Werner, and Shuah Khan.
 
 - New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
 
 - Minor devfreq cleanups, fixes and MAINTAINERS update from
   MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
   Wei Yongjun.
 
 - OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
   driver updates from Andrii Tseglytskyi and Nishanth Menon.
 
 /
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJR0ZNOAAoJEKhOf7ml8uNsDLYP/0EU4rmvw0TWTITfp6RS1KDE
 9GwBn96ZR4Q5bJd9gBCTPSqhHOYMqxWEUp99sn/M2wehG1pk/jw5LO56+2IhM3UZ
 g1HDcJ7te2nVT/iXsKiAGTVhU9Rk0aYwoVSknwk27qpIBGxW9w/s5tLX8pY3Q3Zq
 wL/7aTPjyL+PFFFEaxgH7qLqsl3DhbtYW5AriUBTkXout/tJ4eO1b7MNBncLDh8X
 VQ/0DNCKE95VEJfkO4rk9RKUyVp9GDn0i+HXCD/FS4IA5oYzePdVdNDmXf7g+swe
 CGlTZq8pB+oBpDiHl4lxzbNrKQjRNbGnDUkoRcWqn0nAw56xK+vmYnWJhW99gQ/I
 fKnvxeLca5po1aiqmC4VSJxZIatFZqLrZAI4dzoCLWY+bGeTnCKmj0/F8ytFnZA2
 8IuLLs7/dFOaHXV/pKmpg6FAlFa9CPxoqRFoyqb4M0GjEarADyalXUWsPtG+6xCp
 R/p0CISpwk+guKZR/qPhL7M654S7SHrPwd2DPF0KgGsvk+G2GhoB8EzvD8BVp98Z
 9siCGCdgKQfJQVI6R0k9aFmn/4gRQIAgyPhkhv9tqULUUkiaXki+/t8kPfnb8O/d
 zep+CA57E2G8MYLkDJfpFeKS7GpPD6TIdgFdGmOUC0Y6sl9iTdiw4yTx8O2JM37z
 rHBZfYGkJBrbGRu+Q1gs
 =VBBq
 -----END PGP SIGNATURE-----

Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management and ACPI updates from Rafael Wysocki:
 "This time the total number of ACPI commits is slightly greater than
  the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
  remains the most active patch submitter.

  To me, the most significant change is the addition of offline/online
  device operations to the driver core (with the Greg's blessing) and
  the related modifications of the ACPI core hotplug code.  Next are the
  freezer updates from Colin Cross that should make the freezing of
  tasks a bit less heavy weight.

  We also have a couple of regression fixes, a number of fixes for
  issues that have not been identified as regressions, two new drivers
  and a bunch of cleanups all over.

  Highlights:

   - Hotplug changes to support graceful hot-removal failures.

     It sometimes is necessary to fail device hot-removal operations
     gracefully if they cannot be carried out completely.  For example,
     if memory from a memory module being hot-removed has been allocated
     for the kernel's own use and cannot be moved elsewhere, it's
     desirable to fail the hot-removal operation in a graceful way
     rather than to crash the kernel, but currenty a success or a kernel
     crash are the only possible outcomes of an attempted memory
     hot-removal.  Needless to say, that is not a very attractive
     alternative and it had to be addressed.

     However, in order to make it work for memory, I first had to make
     it work for CPUs and for this purpose I needed to modify the ACPI
     processor driver.  It's been split into two parts, a resident one
     handling the low-level initialization/cleanup and a modular one
     playing the actual driver's role (but it binds to the CPU system
     device objects rather than to the ACPI device objects representing
     processors).  That's been sort of like a live brain surgery on a
     patient who's riding a bike.

     So this is a little scary, but since we found and fixed a couple of
     regressions it caused to happen during the early linux-next testing
     (a month ago), nobody has complained.

     As a bonus we remove some duplicated ACPI hotplug code, because the
     ACPI-based CPU hotplug is now going to use the common ACPI hotplug
     code.

   - Lighter weight freezing of tasks.

     These changes from Colin Cross and Mandeep Singh Baines are
     targeted at making the freezing of tasks a bit less heavy weight
     operation.  They reduce the number of tasks woken up every time
     during the freezing, by using the observation that the freezer
     simply doesn't need to wake up some of them and wait for them all
     to call refrigerator().  The time needed for the freezer to decide
     to report a failure is reduced too.

     Also reintroduced is the check causing a lockdep warining to
     trigger when try_to_freeze() is called with locks held (which is
     generally unsafe and shouldn't happen).

   - cpufreq updates

     First off, a commit from Srivatsa S Bhat fixes a resume regression
     introduced during the 3.10 cycle causing some cpufreq sysfs
     attributes to return wrong values to user space after resume.  The
     fix is kind of fresh, but also it's pretty obvious once Srivatsa
     has identified the root cause.

     Second, we have a new freqdomain_cpus sysfs attribute for the
     acpi-cpufreq driver to provide information previously available via
     related_cpus.  From Lan Tianyu.

     Finally, we fix a number of issues, mostly related to the
     CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
     up some code.  The majority of changes from Viresh Kumar with bits
     from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
     Arnd Bergmann, and Tang Yuantian.

   - ACPICA update

     A usual bunch of updates from the ACPICA upstream.

     During the 3.4 cycle we introduced support for ACPI 5 extended
     sleep registers, but they are only supposed to be used if the
     HW-reduced mode bit is set in the FADT flags and the code attempted
     to use them without checking that bit.  That caused suspend/resume
     regressions to happen on some systems.  Fix from Lv Zheng causes
     those registers to be used only if the HW-reduced mode bit is set.

     Apart from this some other ACPICA bugs are fixed and code cleanups
     are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
     Zhang Rui.

   - cpuidle updates

     New driver for Xilinx Zynq processors is added by Michal Simek.

     Multidriver support simplification, addition of some missing
     kerneldoc comments and Kconfig-related fixes come from Daniel
     Lezcano.

   - ACPI power management updates

     Changes to make suspend/resume work correctly in Xen guests from
     Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
     cleanups and fixes of the ACPI device power state selection
     routine.

   - ACPI documentation updates

     Some previously missing pieces of ACPI documentation are added by
     Lv Zheng and Aaron Lu (hopefully, that will help people to
     uderstand how the ACPI subsystem works) and one outdated doc is
     updated by Hanjun Guo.

   - Assorted ACPI updates

     We finally nailed down the IA-64 issue that was the reason for
     reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
     against objects having scan handlers"), so we can fix it and move
     the ACPI scan handler check added to the ACPI video driver back to
     the core.

     A mechanism for adding CMOS RTC address space handlers is
     introduced by Lan Tianyu to allow some EC-related breakage to be
     fixed on some systems.

     A spec-compliant implementation of acpi_os_get_timer() is added by
     Mika Westerberg.

     The evaluation of _STA is added to do_acpi_find_child() to avoid
     situations in which a pointer to a disabled device object is
     returned instead of an enabled one with the same _ADR value.  From
     Jeff Wu.

     Intel BayTrail PCH (Platform Controller Hub) support is added to
     the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
     driver is modified to work around a couple of known BIOS issues.
     Changes from Mika Westerberg and Heikki Krogerus.

     The EC driver is fixed by Vasiliy Kulikov to use get_user() and
     put_user() instead of dereferencing user space pointers blindly.

     Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
     Kani.

   - Assorted power management updates

     The "runtime idle" helper routine is changed to take the return
     values of the callbacks executed by it into account and to call
     rpm_suspend() if they return 0, which allows us to reduce the
     overall code bloat a bit (by dropping some code that's not
     necessary any more after that modification).

     The runtime PM documentation is updated by Alan Stern (to reflect
     the "runtime idle" behavior change).

     New trace points for PM QoS are added by Sahara
     (<keun-o.park@windriver.com>).

     PM QoS documentation is updated by Lan Tianyu.

     Code cleanups are made and minor issues are addressed by Bernie
     Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.

   - devfreq updates

     New driver for the Exynos5-bus device from Abhilash Kesavan.

     Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
     Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.

   - OMAP power management updates

     Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
     updates from Andrii Tseglytskyi and Nishanth Menon."

* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
  cpufreq: Fix cpufreq regression after suspend/resume
  ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
  PM / Sleep: Warn about system time after resume with pm_trace
  cpufreq: don't leave stale policy pointer in cdbs->cur_policy
  acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
  cpufreq: make sure frequency transitions are serialized
  ACPI: implement acpi_os_get_timer() according the spec
  ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
  ACPI: Add CMOS RTC Operation Region handler support
  ACPI / processor: Drop unused variable from processor_perflib.c
  cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
  cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
  cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
  cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
  cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
  cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
  cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
  cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
  cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
  cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
  ...
2013-07-03 14:35:40 -07:00
Linus Torvalds
ab53485739 Merge branch 'exotic-arch-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull "exotic" arch fixes from Geert Uytterhoeven:
 "This is a collection of several exotic architecture fixes, and a few
  other fixes for issues that were detected while doing the former"

* 'exotic-arch-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (35 commits)
  lib: Move fonts from drivers/video/console/ to lib/fonts/
  console/font: Refactor font support code selection logic
  Revert "staging/solo6x10: depend on CONFIG_FONTS"
  input: cros_ec_keyb_clear_keyboard() depends on CONFIG_PM_SLEEP
  score: Wire up asm-generic/xor.h
  score: Remove unneeded <asm/dma-mapping.h>
  openrisc: Wire up asm-generic/xor.h
  h8300/boot: Use POSIX "$((..))" instead of bashism "$[...]"
  h8300: Mark H83002 and H83048 CPU support broken
  h8300: Switch h8300 to drivers/Kconfig
  h8300: Limit timer channel ranges in Kconfig
  h8300: Wire up asm-generic/xor.h
  h8300: Fill the system call table using a CALL() macro
  h8300: Fix <asm/tlb.h>
  h8300: Hardcode symbol prefixes in asm sources
  h8300: add missing definition for read_barries_depends()
  frv: head.S - Remove commented-out initialization code
  cris: Wire up asm-generic/vga.h
  parport: disable PC-style parallel port support on cris
  console: Disable VGA text console support on cris
  ...
2013-07-03 11:12:08 -07:00
Linus Torvalds
42daabf62b ARM SoC late changes
These are changes that arrived a little late before the merge
 window or that have multiple dependencies on previous branches
 so they did not fit into one of the earlier ones. There
 are 10 branches merged here, a total of 39 non-merge commits.
 Contents are a mixed bag for the above reasons:
 
 * Two new SoC platforms: ST microelectronics stixxxx and
   the TI 'Nspire' graphing calculator. These should have
   been in the 'soc' branch but were a little late
 * Support for the Exynos 5420 variant in mach-exynos,
   which is based on the other exynos branches to avoid
   conflicts.
 * Various small changes for sh-mobile, ux500 and davinci
 * Common clk support for MSM
 
 Conflicts:
 * In Kconfig.debug, various additions trivially conflict,
   the list should be kept in alphabetical order when
   resolving.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAUdLnl2CrR//JCVInAQIrKhAAwvtsGNe6j9nDuLEitWtQAmhHYZQyUJ8k
 o9j/1j1CqhE8C0bLRud8D4m1GxfxbGeRm2d0HoNbxda3FmntUufqBDi6neMiQiLO
 VltC5rOYL8Mday0Asc3SBfjBj8SZC2bypicKy5zUfzsObCBt343g1WvYffMDNmwH
 FveOQK6q2BKmO67cazc9tk5xmxjVwP/LB8r5mQtiXmMguw0R+ZIDDIP6xaURFkxX
 SAElleD2wtvpVHP1d6AKHpXN99u3xV3uoJjKljECEXdBzW/ZX8m7FG2tKY5xy368
 ta0Nhh2MSRnBhUYOH9uah4PQWYEsbZ+M/W+3J9tKRu6q9D/c/AAxILyXUY2tcHNC
 o1UwcUn1druirx3X1AW8HYAGNwW7BD3HANzIiUkQZG7ByfM4qCtUEo2SAFNIGBoR
 v1FMLhMPgMWotZnKrDQQd0anxkKIOFaSMRVgpQLW2jQt/B7sHLmEH2yDffkbSD76
 PQDThnW/dfm9dgeK+X4fPrveIMKbjQlbFz0okN+LPsUf8e1045HBgCi2A0lTIGWM
 kVVgXHKKXi8G8HBa4VyDlORVHXk1bJEheF+zlDvdk4fHkcf+H/OfvFG2O9TdIdpb
 ITXRyyteaRM4YIZpnJbzeeZDZXT89c2ah7xq36iM+L1ScidyntPquViXeasSc8r6
 pKu9ZDc0Mow=
 =cRu2
 -----END PGP SIGNATURE-----

Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC late changes from Arnd Bergmann:
 "These are changes that arrived a little late before the merge window
  or that have multiple dependencies on previous branches so they did
  not fit into one of the earlier ones.  There are 10 branches merged
  here, a total of 39 non-merge commits.  Contents are a mixed bag for
  the above reasons:

   * Two new SoC platforms: ST microelectronics stixxxx and the TI
     'Nspire' graphing calculator.  These should have been in the 'soc'
     branch but were a little late
   * Support for the Exynos 5420 variant in mach-exynos, which is based
     on the other exynos branches to avoid conflicts.
   * Various small changes for sh-mobile, ux500 and davinci
   * Common clk support for MSM"

* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
  ARM: ux500: bail out on alien cpus
  ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
  serial: sh-sci: Initialise variables before access in sci_set_termios()
  ARM: stih41x: Add B2020 board support
  ARM: stih41x: Add B2000 board support
  ARM: sti: Add DEBUG_LL console support
  ARM: sti: Add STiH416 SOC support
  ARM: sti: Add STiH415 SOC support
  ARM: msm: Migrate to common clock framework
  ARM: msm: Make proc_comm clock control into a platform driver
  ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
  ARM: msm: Remove clock-7x30.h include file
  ARM: msm: Remove custom clk_set_{max,min}_rate() API
  ARM: msm: Remove custom clk_set_flags() API
  msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
  msm: iommu: Convert to clk_prepare/unprepare
  msm_sdcc: Convert to clk_prepare/unprepare
  usb: otg: msm: Convert to clk_prepare/unprepare
  msm_serial: Use devm_clk_get() and properly return errors
  msm_serial: Convert to clk_prepare/unprepare
  ...
2013-07-02 14:42:51 -07:00
Linus Torvalds
0bf6a210a4 ARM SoC driver specific changes
These changes are all driver specific and cross over between arm-soc
 contents and some other subsystem, in these cases cpufreq, crypto,
 dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
 have these changes merged through arm-soc. As we proceed to untangle
 the dependencies between platform code and driver code, the amount of
 changes in this category is fortunately shrinking, for 3.11 we have
 16 branches here and 101 non-merge changesets, the majority of which
 are for the stedma40 dma engine driver used in the ux500 platform.
 Cleaning up that code touches multiple subsystems, but gets rid
 of the dependency in the end.
 
 The mailbox code moved out from mach-omap2 to drivers/mailbox
 is an intermediate step and is still omap specific at the moment.
 Patches exist to generalize the subsystem and add other drivers
 with the same API, but those did not make it for 3.11.
 
 Conflicts:
 * In cpu-db8500.c results from the removal of the u8500_of_init_devices
   function in combination with the split of u8500_auxdata_lookup.
 
 * In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
   we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAUdLnomCrR//JCVInAQJI/A/9FydsQa9sdnzLFgcdX5BeRRwkXLfDifCM
 zDTfUBo+LriKOs7QHblmDg1MnY1UMB2IfrdHD0FsjK7WbZ/91EMAGDPYcI7Fu4+u
 pGStxwWi2v+oCT1jjeOkCPT7hdCqogsSpybYq8itSb+zdvdOi6U35dWEKz8xGqz4
 vTL9gTZbJP0kowkjIcaryk7FIj7BTIvMCW8n55JZEkDe0BuSJGYn5c3Mntut12ZK
 5xM2PeNe2sd3dIdA6XbM2ye/XmYa8xY8Qu4/ijxfH1gnJLvz9Unp96nRXpEbIeMb
 BH2Sro8dxsMCaweIQhSRKGnUWMYO/Rh7/+5EqzJ163Ezthx9nvHXJY2ndWuD7uM1
 IcGrMxLtqP22TEMtZAVEATDp/5ymxEo5GM+eayUojQDn213wOJjRs5xz5IBsH4KM
 8CM/gpadWmLjWku72yEV4lryLcdS0NVQzpTnEbILEGOU4u7qJtxRAp7x7tWBtFg8
 4m/eWcSVk/U2SYbXmQHsfukuWgKY0cnZbctPcdnaqXwTP7toJEAK3gxoMtWh49Jq
 2M2PVFyFejaaq5b/71wAJ7ePYw56H0N/F3RsGpPE55AY15++gSoQ+3t2Si68hDw8
 NtyJMkQYpTvtqJbHXWpQQ3Zfs7pDBe01WDV7i+m4JTNggxUDaO/t1Fqp+fEksm4J
 r+luEf5Gcgk=
 =mJsI
 -----END PGP SIGNATURE-----

Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver specific changes from Arnd Bergmann:
 "These changes are all driver specific and cross over between arm-soc
  contents and some other subsystem, in these cases cpufreq, crypto,
  dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
  these changes merged through arm-soc.

  As we proceed to untangle the dependencies between platform code and
  driver code, the amount of changes in this category is fortunately
  shrinking, for 3.11 we have 16 branches here and 101 non-merge
  changesets, the majority of which are for the stedma40 dma engine
  driver used in the ux500 platform.  Cleaning up that code touches
  multiple subsystems, but gets rid of the dependency in the end.

  The mailbox code moved out from mach-omap2 to drivers/mailbox is an
  intermediate step and is still omap specific at the moment.  Patches
  exist to generalize the subsystem and add other drivers with the same
  API, but those did not make it for 3.11."

* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
  crypto: ux500: use dmaengine_submit API
  crypto: ux500: use dmaengine_prep_slave_sg API
  crypto: ux500: use dmaengine_device_control API
  crypto: ux500/crypt: add missing __iomem qualifiers
  crypto: ux500/hash: add missing static qualifiers
  crypto: ux500/hash: use readl on iomem addresses
  dmaengine: ste_dma40: Declare memcpy config as static
  ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
  ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
  ARM: ux500: Provide a AB8500 GPIO Device Tree node
  gpio: rcar: fix gpio_rcar_of_table
  gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
  gpio-rcar: Reference core gpio documentation in the DT bindings
  clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
  ARM: dts: Update Samsung I2S documentation
  ARM: dts: add clock provider information for i2s controllers in Exynos5250
  ARM: dts: add Exynos audio subsystem clock controller node
  clk: samsung: register audio subsystem clocks using common clock framework
  ARM: dts: use #include for all device trees for Samsung
  pinctrl: s3c24xx: use correct header for chained_irq functions
  ...
2013-07-02 14:33:21 -07:00
Linus Torvalds
3883cbb6c1 ARM SoC specific changes
These changes are all to SoC-specific code, a total of 33 branches on
 17 platforms were pulled into this. Like last time, Renesas sh-mobile
 is now the platform with the most changes, followed by OMAP and EXYNOS.
 
 Two new platforms, TI Keystone and Rockchips RK3xxx are added in
 this branch, both containing almost no platform specific code at all,
 since they are using generic subsystem interfaces for clocks, pinctrl,
 interrupts etc. The device drivers are getting merged through the
 respective subsystem maintainer trees.
 
 One more SoC (u300) is now multiplatform capable and several others
 (shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
 towards that goal with this series but need more work.
 
 Also noteworthy is the work on PCI here, which is traditionally part of
 the SoC specific code. With the changes done by Thomas Petazzoni, we can
 now more easily have PCI host controller drivers as loadable modules and
 keep them separate from the platform code in drivers/pci/host. This has
 already led to the discovery that three platforms (exynos, spear and imx)
 are actually using an identical PCIe host controller and will be able
 to share a driver once support for spear and imx is added.
 
 Conflicts:
 * asm/glue-proc.h has one CPU type getting added that conflicts
   with another addition in 3.10-rc7
 * Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAUdLnpmCrR//JCVInAQLoFRAAyatR+MhVFwc91cO7yDw/mz81RO1V9jEd
 QMufoWi0BRfBsubqxnGlb510EEMTz7gxdrlYPILYNr8TqR+lNGhjKt2FQAjN3q2O
 IBvu4x8C+xcxnMNbkCnTQRxP/ziK6yCI6e7enQhwuMuJwvsnJtGbsqKi5ODMw6x0
 o5EQmIdj5NhhSJqJZPCmWsKbx100TH1UwaEnhNl0DSaFj51n3bVRrK6Nxce10GWZ
 HsS1/a63lq/YZLkwfUEvgin/PU9Jx5jMmqhlp3bZjG+f1ItdzJF+9IgS248vCIi2
 ystzWCH88Kh69UFcYFfCjeZe8H45XcP+Zykd8WC0DvF/a7Hwk5KTKE/ciT6RPRxb
 rkWW5EwjqZL9w9cU3rUHWtSVenayQMMEmCfksadr1AExyCrhPqfs9RINyBs2lK5a
 q2bdSFbXZsNzSyL+3yQAfChvRo1/2FdlFVQy+oVUCActV7L77Y7y6jl+b2qzFsSu
 xMKwvC/1vDXTvOnGk6A/qJu7yrHpqJrvw1eI+wnMswNBl7lCTgyyHnr5y8S092jI
 KU4hmSxsYP+y13HmKy4ewPy9DYJYBTSdReKfEFo79Dx8eqySAWjHFL/OPRqhCUYS
 kBq0eZpVZO7tJnHRaRz8n93wIYzb1UOhhgVwxdjPZF9L4d/jzh1BCv0OBWv8IXCu
 uWLAi92lL24=
 =0r9S
 -----END PGP SIGNATURE-----

Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC specific changes from Arnd Bergmann:
 "These changes are all to SoC-specific code, a total of 33 branches on
  17 platforms were pulled into this.  Like last time, Renesas sh-mobile
  is now the platform with the most changes, followed by OMAP and
  EXYNOS.

  Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
  branch, both containing almost no platform specific code at all, since
  they are using generic subsystem interfaces for clocks, pinctrl,
  interrupts etc.  The device drivers are getting merged through the
  respective subsystem maintainer trees.

  One more SoC (u300) is now multiplatform capable and several others
  (shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
  towards that goal with this series but need more work.

  Also noteworthy is the work on PCI here, which is traditionally part
  of the SoC specific code.  With the changes done by Thomas Petazzoni,
  we can now more easily have PCI host controller drivers as loadable
  modules and keep them separate from the platform code in
  drivers/pci/host.  This has already led to the discovery that three
  platforms (exynos, spear and imx) are actually using an identical PCIe
  host controller and will be able to share a driver once support for
  spear and imx is added."

* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
  ARM: integrator: let pciv3 use mem/premem from device tree
  ARM: integrator: set local side PCI addresses right
  ARM: dts: Add pcie controller node for exynos5440-ssdk5440
  ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
  ARM: EXYNOS: Enable PCIe support for Exynos5440
  pci: Add PCIe driver for Samsung Exynos
  ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
  ARM: keystone: Move CPU bringup code to dedicated asm file
  ARM: multiplatform: always pick one CPU type
  ARM: imx: select syscon for IMX6SL
  ARM: keystone: select ARM_ERRATA_798181 only for SMP
  ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
  ARM: OMAP2+: AM43x: resolve SMP related build error
  dmaengine: edma: enable build for AM33XX
  ARM: edma: Add EDMA crossbar event mux support
  ARM: edma: Add DT and runtime PM support to the private EDMA API
  dmaengine: edma: Add TI EDMA device tree binding
  arm: add basic support for Rockchip RK3066a boards
  arm: add debug uarts for rockchip rk29xx and rk3xxx series
  arm: Add basic clocks for Rockchip rk3066a SoCs
  ...
2013-07-02 13:43:38 -07:00
Linus Torvalds
0de10f9ea6 TTY/Serial merge for 3.11-rc1
Here is the big TTY / Serial driver merge for 3.11-rc1.
 
 It's not all that big, nothing major changed in the tty api, which is a
 nice change, just a number of serial driver fixes and updates and new
 drivers, along with some n_tty fixes to help resolve some reported
 issues.
 
 All of these have been in the linux-next releases for a while, with the
 exception of the last revert patch, which was reported this past weekend
 by two different people as being needed.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEYEABECAAYFAlHRtNIACgkQMUfUDdst+ymYgwCeKdyv9wRJ5cIWZt7Jz8ou3P/C
 76YAoIvMv+fwoFBpyud/sC8eAKGTQ6KB
 =Sjk6
 -----END PGP SIGNATURE-----

Merge tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial updates from Greg KH:
 "Here is the big TTY / Serial driver merge for 3.11-rc1.

  It's not all that big, nothing major changed in the tty api, which is
  a nice change, just a number of serial driver fixes and updates and
  new drivers, along with some n_tty fixes to help resolve some reported
  issues.

  All of these have been in the linux-next releases for a while, with
  the exception of the last revert patch, which was reported this past
  weekend by two different people as being needed."

* tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (51 commits)
  Revert "serial: 8250_pci: add support for another kind of NetMos Technology PCI 9835 Multi-I/O Controller"
  pch_uart: Add uart_clk selection for the MinnowBoard
  tty: atmel_serial: prepare clk before calling enable
  tty: Reset itty for other pty
  n_tty: Buffer work should not reschedule itself
  n_tty: Fix unsafe update of available buffer space
  n_tty: Untangle read completion variables
  n_tty: Encapsulate minimum_to_wake within N_TTY
  serial: omap: Fix device tree based PM runtime
  serial: imx: Fix serial clock unbalance
  serial/mpc52xx_uart: fix kernel panic when system reboot
  serial: mfd: Add sysrq support
  serial: imx: enable the clocks for console
  tty: serial: add Freescale lpuart driver support
  serial: imx: Improve Kconfig text
  serial: imx: Allow module build
  serial: imx: Fix warning when !CONFIG_SERIAL_IMX_CONSOLE
  tty/serial/sirf: fix error propagation in sirfsoc_uart_probe()
  serial: omap: fix potential NULL pointer dereference in serial_omap_runtime_suspend()
  tty: serial: Enable uartlite for ARM zynq
  ...
2013-07-02 11:32:06 -07:00
Rafael J. Wysocki
e52cff8bdd Merge branch 'pm-assorted'
* pm-assorted:
  PM / QoS: Add pm_qos and dev_pm_qos to events-power.txt
  PM / QoS: Add dev_pm_qos_request tracepoints
  PM / QoS: Add pm_qos_request tracepoints
  PM / QoS: Add pm_qos_update_target/flags tracepoints
  PM / QoS: Update Documentation/power/pm_qos_interface.txt
  PM / Sleep: Print last wakeup source on failed wakeup_count write
  PM / QoS: correct the valid range of pm_qos_class
  PM / wakeup: Adjust messaging for wake events during suspend
  PM / Runtime: Update .runtime_idle() callback documentation
  PM / Runtime: Rework the "runtime idle" helper routine
  PM / Hibernate: print physical addresses consistently with other parts of kernel
2013-06-28 13:01:40 +02:00
Olof Johansson
8c3d913888 MSM clock updates for 3.11.
Per Stephen Boyd's coverletter:
 
 Resending to collect higher level maintainer acks per Olof's request.
 The plan is to push this patchset through MSM to the arm-soc tree.
 
 This patchset moves the existing MSM clock code and affected drivers
 to the common clock framework. A prerequisite of moving to the common
 clock framework is to use clk_prepare() and clk_enable() so the first
 few patches migrate drivers to that call (clk_prepare() is a no-op on
 MSM right now). It also removes some custom clock APIs that MSM
 provides and finally moves the proc_comm clock code to the common
 struct clk.
 
 This patch series will be used as the foundation of the MSM 8660/8960
 clock code that I plan to send out after this series.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJRyK/7AAoJEOa6n1xeVN+Cu1UQALf7pzve7+JMbpHp9HtQPTCk
 GxGBBZ5ay0yWYYSSDRNqMbxNAHxhTuz26AW1CSSAHNpxotMB9t1y4AGkbSqxl3H8
 gZZ+9PwSBGN6kABSjfrae1kPxnU6Mg/9J56E5iXFLst0qIvgDejUGG8BXLHDuzjM
 weQZJf6p6t9SZIHc/80RUsiVmRkqKM9Mp6NvyO4irQOKwfvQ76mjWNqiUrQS7wwA
 +glbwR3PMg31bvUXOcWuoBp3zbZYvN65bUSwZMIagynqYqU8g+bwDA2NQKjFzoXM
 ActLyurznSytcER+/+3JbRh32kMI1Bh/jnH2VbqS4TNQbtIuJd6VjYP4kE4HsRsZ
 MkK2pEUS4GuMEdLqeJW3d5ch+u45CQVdtDLuSUH0e9j3RqQNHmZWIvp3IhXouKG+
 HMeeo2RQfdn3Y7A+TJ18llVUW/2BTBKjnr1MvR+9JoZmMpkV0tnVnD19MQcKvEXK
 dM7Qp7apAS5KpXPTsWvRXwT4uFHoGiRpyluI2UrqEjOVhYQW4DBzfJ/GQDJ80Wd8
 HFH0ZPjvi2W3jLeFqOwGYzbcMgyGe4pvkkUm1yj/EV3j5GyFSCPxOhqn4t/fJegk
 Vg2AMDeSf+cb504pr8AkfYF0Z0RqGBTgyKOwslgGwaRCppOHW7DZL0R6M3/5a48H
 9C4z3RJ4UcTt1a93ZaV3
 =0OVE
 -----END PGP SIGNATURE-----

Merge tag 'msm-clock-for-3.11b' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/late

From David Brown:
MSM clock updates for 3.11.

Per Stephen Boyd's coverletter:

Resending to collect higher level maintainer acks per Olof's request.
The plan is to push this patchset through MSM to the arm-soc tree.

This patchset moves the existing MSM clock code and affected drivers
to the common clock framework. A prerequisite of moving to the common
clock framework is to use clk_prepare() and clk_enable() so the first
few patches migrate drivers to that call (clk_prepare() is a no-op on
MSM right now). It also removes some custom clock APIs that MSM
provides and finally moves the proc_comm clock code to the common
struct clk.

This patch series will be used as the foundation of the MSM 8660/8960
clock code that I plan to send out after this series.

* tag 'msm-clock-for-3.11b' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
  ARM: msm: Migrate to common clock framework
  ARM: msm: Make proc_comm clock control into a platform driver
  ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
  ARM: msm: Remove clock-7x30.h include file
  ARM: msm: Remove custom clk_set_{max,min}_rate() API
  ARM: msm: Remove custom clk_set_flags() API
  msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
  msm: iommu: Convert to clk_prepare/unprepare
  msm_sdcc: Convert to clk_prepare/unprepare
  usb: otg: msm: Convert to clk_prepare/unprepare
  msm_serial: Use devm_clk_get() and properly return errors
  msm_serial: Convert to clk_prepare/unprepare

Acked-by: Chris Ball <cjb@laptop.org> # for msm_sdcc.c
Signed-off-by: Olof Johansson <olof@lixom.net>
2013-06-27 17:04:27 -07:00
Sebastian Andrzej Siewior
3a0ddc714a usb: musb: omap2430: make it compile again
it does not compile since 09fc7d ("usb: musb: fix incorrect usage of
resource pointer"). What makes me wonder most is if source of the
Tested-by tag :)

Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-25 16:41:07 -07:00
Fabio Estevam
046916de11 usb: chipidea: ci_hdrc_imx: access phy via private data
commit ea1418b5f1 (usb: chipidea: i.MX: use devm_usb_get_phy_by_phandle to get
phy) causes the USB host to miss the disconnect/connect events.

In order to reproduce this problem:

- Insert a USB thumb into the USB host port (connection is detected)
- Remove it (no disconnect event will be reported)
- Insert the USB thumb again (connection is not detected)

Fix this problem by accessing the usb_phy structure using the private data
instead of accessing a local structure.

Tested on a mx28evk board.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-25 16:41:06 -07:00
Emil Goode
1f21569c0f xhci: Add missing unlocks on error paths
This patch adds missing unlocks on error paths in the
xhci_free_streams and xhci_configure_endpoint functions.

Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-06-25 16:41:06 -07:00