RT715 and RT714 are essentially the same chips but with different
SoundWire Dev_ID registers, make sure we can probe the same driver if
RT714 is used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Jack Yu <jack.yu@realtek.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201002211902.287692-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A deadlock is identified when there are three contexts running at the
same time:
- a HDMI jack work which is calling snd_soc_dapm_sync().
- user space is calling snd_pcm_release() to close pcm device.
- pm is calling runtime suspend function of HDMI codec driver.
By removing the clear_dapm_works() invocation in the
hdac_hdmi_runtime_suspend() function, the snd_pcm_release() could
always returns from dapm_power_widgets() function call without
blocking the hdac_hdmi_jack_dapm_work() work thread or being blocked
by the hdac_hdmi_runtime_suspend() function. The purpose of the jack
work is to enable/disable the dapm jack pin so it's not necessary to
cancel the work in runtime suspend function which is usually called
when pcm device is closed.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Link: https://lore.kernel.org/r/1594818110-786-1-git-send-email-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS4234 is a highly versatile CODEC that combines 4 channels of
high performance analog to digital conversion, 4 channels of high
performance digital to analog conversion for audio, and 1 channel of
digital to analog conversion to provide a nondelayed audio reference
signal to an external Class H tracking power supply.
DAC5 is only supported as a 5th audio channel. Tracking Power Supply
mode is not currently supported by the driver.
In DSP_A mode the slots for DAC1-4 and optionally DAC5 can be set.
The codec always claims 4 slots for DAC1-4 and these must be in the
same nibble of the mask. The codec has a fixed mapping for ADC slots.
In I2S/LJ modes the codec has a fixed mapping for DAC1-4 and ADC1-4.
DAC5 is not available in these modes.
The MCLK source must be preset to a valid frequency before probe()
because it must be running all the time the codec is out of reset.
The VA_SEL bit will be set automatically to 3.3v or 5v during probe()
based on the reported voltage of the regulator supplying VA.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200928111821.26967-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 400ms power-up delay recommended to fix pop noise on capture.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200925210509.83353-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unused variables in the private struct and the code as these
variables are initially set and then there is no additional code
utilizing these variables.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-6-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the code to support the asi-format binding property. The code
does nothing except read the property and set a variable. No additional
action is taken except to reset the variable. The property is supposed
to set the rising or falling RX edge detection of the SBCLK but this
edge detection is done by checking the DAI_FMT_INV_MASK.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-5-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the regcache to cache data and mark cache as dirty when the device
is shutdown when suspend is called. When the device is woken up then
sync the cache and set to not caching the data.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200923132600.10652-3-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When SND_SOC_CROS_EC_CODEC is enabled and CRYPTO is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for CRYPTO_LIB_SHA256
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- SND_SOC_CROS_EC_CODEC [=y] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && CROS_EC [=y]
The reason is that SND_SOC_CROS_EC_CODEC selects CRYPTO_LIB_SHA256 without
depending on or selecting CRYPTO while CRYPTO_LIB_SHA256 is subordinate to
CRYPTO.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Fixes: 93fa0af479 ("ASoC: cros_ec_codec: switch to library API for SHA-256")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Link: https://lore.kernel.org/r/20200917141803.92889-1-fazilyildiran@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove duplicate code for programming the I/V sense the call to update
the register was duplicated in commit 09ed395b05 ("ASoC: tas2562:
Add voltage sense slot configuration").
Fixes: 09ed395b05 ("ASoC: tas2562: Add voltage sense slot configuration")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200922142411.10364-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use set_jack ops to set jack so machine drivers do not need to include
hdmi-codec.h explicitly.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200922062316.1172935-1-cychiang@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor the tas2770_set_samplerate to simplify the code and access the
I2C bus only once per rate request. The ramp rate and sample rate bits
are contained in the same register so a single call to the
snd_soc_update_bits function is all that is needed
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-9-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix up the spacing for argument alignment and add new lines to separate
code. Eliminate unneccessary goto statements when the error code could
just be returned.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-8-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the hardcoded masks with the GENMASK macro. Also update some of
the hardcoded bits with the BIT macro
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-6-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the unbalanced call to the pm_runtime_disable when removing the
module. pm_runtime_enable is not called nor is the pm_runtime setup in
the code. Remove the i2c_remove function and the pm_runtime_disable.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-5-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the TAS2110 amplifier to the TAS2562 driver. The TAS2110 is register
and bitmap compatible. The chips differ in that the TAS2110 does not
have the I/V Sense feedback path. Since these features do not exist the
device needs to be registered without these controls.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200921153820.18357-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
At power-up the analog circuits may take up to one full second before
being charged with the default configuration. Using the analog blocks
before they are ready generates a *very* crappy sound.
Enable the fast charge feature, which will require a bit more power
than normal charge but will definitely speed up the starting operation
by shrinking this delay to up to 40 ms.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20200911173140.29984-4-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code expects a single channel to be always used. Fix this
situation by forwarding the number of channels used. Then fix the
derivation of the bdiv clock rate.
Fixes: 96c3bb0023 ("ASoC: tlv320aic32x4: Dynamically Determine Clocking")
Suggested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20200911173140.29984-3-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As indicated in the datasheet, a 10ms delay must be observed after
programming the divisors.
The lack of delay prevents the codec to work properly and the playback
appears extremely slow and totally un-audible on a custom sama5 based
board.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20200911173140.29984-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid the IO error, we need to cancel the delayed work and wait for it to finish.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200921094308.31921-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_update_bits returns a 1 when the bit was successfully updated,
returns a 0 is no update was needed and a negative if the call failed.
The code is currently failing the case of a successful update by just
checking for a non-zero number. Modify these checks and return the error
code only if there is a negative.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-7-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devicetree binding indicates that the ti,asi-format, ti,imon-slot-no
and ti,vmon-slot-no are not required but the driver requires them or it
fails to probe. Honor the binding and allow these entries to be optional
and set the corresponding values to the default values for each as defined
in the data sheet.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-4-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the BIAS_STANDBY and BIAS_PREPARE to the set_bias_level or else the
driver will return -EINVAL which is not correct as they are valid
states.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
tas2770_reset is called during i2c probe. The reset calls the
snd_soc_component_write which depends on the tas2770->component being
available. The component pointer is not set until codec_probe so move
the reset to the codec_probe after the pointer is set.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918190548.12598-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid the IO error, we need to cancel the delayed work and wait for it to finish.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200921094244.31869-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the TAS2564 as a supported amplifier. This amplifier is register,
bitmap and feature compatible to the TAS2562.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200918150130.21015-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to configure the GPIO pin to the specific configuration.
The GPIO pin can be configured as GPO, IRQ, SDOUT2, PDMCLK, MICBASE_EN,
GPI, MCLK, SDIN, PDMDIN1, PDMDIN2, PDMDIN3 or PDMDIN4 and the output
drive can be configured with various configuration.
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20200918114025.18205-2-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ak4458 can't support DSD512 format, but ak4497 can, so add
a new enum variable (enum ak4458_type) in ak4458_drvdata to
distinguish these two platforms.
Ak4497 has two kinds of DSD input pin, it can be selected by
the dsd-path property from DT.
In hw_params(), bit clock is calculated according to different
DSD format (DSD64, DSD128, DSD256, DSD512), then registers
are configured.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1600178220-28973-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code to allow the ASI Tx output to be placed into High-z mode
during unused ASI cycles. This allows for other devices that may be on
the bus to drive the ASI out. By default the 320adcx140 sends 0's for
unused cycles.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-4-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid the actual PLL settings to differ from the state expected by
the clock driver, the codec should only be fully reset before the clocks
are registered. But we also need to ensure that the software reset
happens at all before clock registration, as not all boards have a reset
GPIO.
Move the software reset from aic32x4_component_probe() to
aic32x4_probe() and reorder the reset and registration sequence:
1. Reset via GPIO (if available)
2. Reset via software
3. Register component
4. Register clocks
Note that aic32x4_component_probe() is only called after aic32x4_probe()
has finished, so the reset in aic32x4_component_probe() was happening too
late.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200902133043.19504-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators need to be disabled in the aic32x4_register_clocks()
failure case as well.
Fixes: 9d4befff5a ("ASoC: codec: tlv3204: Moving GPIO reset and add ADC reset")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200902133043.19504-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the BCLK inversion for DSP modes
This is how it is defined by ASoC:
* BCLK:
* - "normal" polarity means signal is available at rising edge of BCLK
* - "inverted" polarity means signal is available at falling edge of BCLK
The adcx140 defines the BCLK edge based on coding type.
The PCM (DSP_A/B) should drive on rising and sample on falling edge, so
from ASoC pov, it is IB_NF. But from the codec pov if it is configured in
DSP mode, then the BCLK should not be inverted, defaults to the coding
standard.
For i2s, it is NB_NF from ASoC pov (drive on falling, sample on rising).
>From the codec's pov BCLK should not invert either, as this is the default
for the coding.
So, inversion must take the format into account:
IB_NF + DSP_A/B == the codec bclk inversion should be disabled
NB_NF + DSP_A/B == the codec bclk inversion should be enabled
NB_NF + I2S == the codec bclk inversion should be disabled
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It was observed that if the device was active and register writes were
performed there were some unwanted behaviors particularly when writing
the word length and some filter options. So when writing to the device
the device should be placed in sleep mode and then exit sleep mode once
the register update is complete.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to its datasheet, the digital gain should be -100 dB when
CHx_DVOL is 1 and 27 dB when CHx_DVOL is 255. But with the current
dig_vol_tlv, "Digital CHx Out Volume" shows 27.5 dB if CHx_DVOL is 255
and -95.5 dB if CHx_DVOL is 1. This commit fixes this bug.
Fixes: 689c7655b5 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20200908090417.16695-1-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds rt1015p codec driver.
Rt1015p is a rt1015 variant.
- It doesn't support I2C.
- It only supports S24, 48kHz, 64FS.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200910042949.3795682-2-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to its datasheet, after reset this codec goes into sleep
mode. In this mode, any register accessing should be avoided except for
exiting sleep mode. Hence this commit moves SLEEP_CFG access before any
register accessing.
Signed-off-by: Camel Guo <camelg@axis.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200908083521.14105-2-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mt6359 platform device is instantiated by mfd_add_devices(). In the
case, dev->of_node is NULL so that mt6359_parse_dt() always fails to
parse the desired DT properties.
Gets the DT properties via dev->parent->of_node.
Fixes: 8061734ab6 ("ASoC: mediatek: mt6359: add codec driver")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200908070044.1142644-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In adcx140_i2c_probe, adcx140->dev is accessed before its
initialization. This commit fixes this bug.
Fixes: 689c7655b5 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Camel Guo <camel.guo@axis.com>
Link: https://lore.kernel.org/r/20200901135736.32036-1-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe of rt5682 is pretty slow. A quick measurement shows that it
takes ~650 ms on at least one board. There's no reason to block all
other drivers waiting for this probe to finish. Set the flag to allow
other drivers to probe while we're probing.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200828162005.1.I4f67f494c4f759b0e5c7f487e040dfdcf16e0876@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
When the wm8958_mic_detect, wm8994_mic_detect functions get called from
the machine driver, e.g. from the card's late_probe() callback, the CODEC
device may be PM runtime suspended and any regmap writes have no effect.
Add PM runtime calls to these functions to ensure the device registers
are updated as expected.
This suppresses an error during boot
"wm8994-codec: ASoC: error at snd_soc_component_update_bits on wm8994-codec"
caused by the regmap access error due to the cache_only flag being set.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200827173357.31891-2-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8994_MICBIAS register is not available in the WM1811 CODEC so skip
initialization of that register for that device.
This suppresses an error during boot:
"wm8994-codec: ASoC: error at snd_soc_component_update_bits on wm8994-codec"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200827173357.31891-1-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the audio routing map to enable the digital mic paths when the
analog mic paths are not enabled.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200828112855.10112-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
