The ice_get_pfa_module_tlv() function iterates over the Type-Length-Value
structures in the Preserved Fields Area (PFA) of the NVM. This is used by
the driver to access data such as the Part Board Assembly identifier.
The function uses simple logic to iterate over the PFA. First, the pointer
to the PFA in the NVM is read. Then the total length of the PFA is read
from the first word.
A pointer to the first TLV is initialized, and a simple loop iterates over
each TLV. The pointer is moved forward through the NVM until it exceeds the
PFA area.
The logic seems sound, but it is missing a key detail. The Preserved
Fields Area length includes one additional final word. This is documented
in the device data sheet as a dummy word which contains 0xFFFF. All NVMs
have this extra word.
If the driver tries to scan for a TLV that is not in the PFA, it will read
past the size of the PFA. It reads and interprets the last dummy word of
the PFA as a TLV with type 0xFFFF. It then reads the word following the PFA
as a length.
The PFA resides within the Shadow RAM portion of the NVM, which is
relatively small. All of its offsets are within a 16-bit size. The PFA
pointer and TLV pointer are stored by the driver as 16-bit values.
In almost all cases, the word following the PFA will be such that
interpreting it as a length will result in 16-bit arithmetic overflow. Once
overflowed, the new next_tlv value is now below the maximum offset of the
PFA. Thus, the driver will continue to iterate the data as TLVs. In the
worst case, the driver hits on a sequence of reads which loop back to
reading the same offsets in an endless loop.
To fix this, we need to correct the loop iteration check to account for
this extra word at the end of the PFA. This alone is sufficient to resolve
the known cases of this issue in the field. However, it is plausible that
an NVM could be misconfigured or have corrupt data which results in the
same kind of overflow. Protect against this by using check_add_overflow
when calculating both the maximum offset of the TLVs, and when calculating
the next_tlv offset at the end of each loop iteration. This ensures that
the driver will not get stuck in an infinite loop when scanning the PFA.
Fixes: e961b679fb ("ice: add board identifier info to devlink .info_get")
Co-developed-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240603-net-2024-05-30-intel-net-fixes-v2-1-e3563aa89b0c@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZmAYPgAKCRDbK58LschI
g2XdAP9M8zYLRw4IG8DUFug7F+oqRPqgbs+Gvsf9YNl5/PSiTQEA6WKa/ObaG/W9
vre9VxhMWKgcMfzqZyztNHAiDm8R+QI=
=l7gV
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-06-05
We've added 8 non-merge commits during the last 6 day(s) which contain
a total of 9 files changed, 34 insertions(+), 35 deletions(-).
The main changes are:
1) Fix a potential use-after-free in bpf_link_free when the link uses
dealloc_deferred to free the link object but later still tests for
presence of link->ops->dealloc, from Cong Wang.
2) Fix BPF test infra to set the run context for rawtp test_run callback
where syzbot reported a crash, from Jiri Olsa.
3) Fix bpf_session_cookie BTF_ID in the special_kfunc_set list to exclude
it for the case of !CONFIG_FPROBE, also from Jiri Olsa.
4) Fix a Coverity static analysis report to not close() a link_fd of -1
in the multi-uprobe feature detector, from Andrii Nakryiko.
5) Revert support for redirect to any xsk socket bound to the same umem
as it can result in corrupted ring state which can lead to a crash when
flushing rings. A different approach will be pursued for bpf-next to
address it safely, from Magnus Karlsson.
6) Fix inet_csk_accept prototype in test_sk_storage_tracing.c which caused
BPF CI failure after the last tree fast forwarding, from Andrii Nakryiko.
7) Fix a coccicheck warning in BPF devmap that iterator variable cannot
be NULL, from Thorsten Blum.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
Revert "xsk: Document ability to redirect to any socket bound to the same umem"
Revert "xsk: Support redirect to any socket bound to the same umem"
bpf: Set run context for rawtp test_run callback
bpf: Fix a potential use-after-free in bpf_link_free()
bpf, devmap: Remove unnecessary if check in for loop
libbpf: don't close(-1) in multi-uprobe feature detector
bpf: Fix bpf_session_cookie BTF_ID in special_kfunc_set list
selftests/bpf: fix inet_csk_accept prototype in test_sk_storage_tracing.c
====================
Link: https://lore.kernel.org/r/20240605091525.22628-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On failed verification of PTP clock pin, error message prints channel
number instead of pin index after "pin", which is incorrect.
Fix error message by adding channel number to the message and printing
pin number instead of channel number.
Fixes: 6092315dfd ("ptp: introduce programmable pins.")
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20240604120555.16643-1-karol.kolacinski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If one TCA_TAPRIO_ATTR_PRIOMAP attribute has been provided,
taprio_parse_mqprio_opt() must validate it, or userspace
can inject arbitrary data to the kernel, the second time
taprio_change() is called.
First call (with valid attributes) sets dev->num_tc
to a non zero value.
Second call (with arbitrary mqprio attributes)
returns early from taprio_parse_mqprio_opt()
and bad things can happen.
Fixes: a3d43c0d56 ("taprio: Add support adding an admin schedule")
Reported-by: Noam Rathaus <noamr@ssd-disclosure.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20240604181511.769870-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of flow rule creation fail in mlx5_lag_create_port_sel_table(),
instead of previously created rules, the tainted pointer is deleted
deveral times.
Fix this bug by using correct flow rules pointers.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 352899f384 ("net/mlx5: Lag, use buckets in hash mode")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240604100552.25201-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan says:
====================
mlx5 core fixes 20240603
This small patchset provides two bug fixes from the team to the mlx5 core driver.
Series generated against:
commit 33700a0c9b ("net/tcp: Don't consider TCP_CLOSE in TCP_AO_ESTABLISHED")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case pci channel becomes offline the driver should not wait for PCI
reads during health dump and recovery flow. The driver has timeout for
each of these loops trying to read PCI, so it would fail anyway.
However, in case of recovery waiting till timeout may cause the pci
error_detected() callback fail to meet pci_dpc_recovered() wait timeout.
Fixes: b3bd076f75 ("net/mlx5: Report devlink health on FW fatal issues")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mainline MTK ethernet driver suffers long time from rarly but
annoying tx queue timeouts. We think that this is caused by fixed
dma sizes hardcoded for all SoCs.
We suspect this problem arises from a low level of free TX DMADs,
the TX Ring alomost full.
The transmit timeout is caused by the Tx queue not waking up. The
Tx queue stops when the free counter is less than ring->thres, and
it will wake up once the free counter is greater than ring->thres.
If the CPU is too late to wake up the Tx queues, it may cause a
transmit timeout.
Therefore, we increased the TX and RX DMADs to improve this error
situation.
Use the dma-size implementation from SDK in a per SoC manner. In
difference to SDK we have no RSS feature yet, so all RX/TX sizes
should be raised from 512 to 2048 byte except fqdma on mt7988 to
avoid the tx timeout issue.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaroslav reports Dell's OMSA Systems Management Data Engine
expects NLM_DONE in a separate recvmsg(), both for rtnl_dump_ifinfo()
and inet_dump_ifaddr(). We already added a similar fix previously in
commit 460b0d33cf ("inet: bring NLM_DONE out to a separate recv() again")
Instead of modifying all the dump handlers, and making them look
different than modern for_each_netdev_dump()-based dump handlers -
put the workaround in rtnetlink code. This will also help us move
the custom rtnl-locking from af_netlink in the future (in net-next).
Note that this change is not touching rtnl_dump_all(). rtnl_dump_all()
is different kettle of fish and a potential problem. We now mix families
in a single recvmsg(), but NLM_DONE is not coalesced.
Tested:
./cli.py --dbg-small-recv 4096 --spec netlink/specs/rt_addr.yaml \
--dump getaddr --json '{"ifa-family": 2}'
./cli.py --dbg-small-recv 4096 --spec netlink/specs/rt_route.yaml \
--dump getroute --json '{"rtm-family": 2}'
./cli.py --dbg-small-recv 4096 --spec netlink/specs/rt_link.yaml \
--dump getlink
Fixes: 3e41af9076 ("rtnetlink: use xarray iterator to implement rtnl_dump_ifinfo()")
Fixes: cdb2f80f1c ("inet: use xa_array iterator to implement inet_dump_ifaddr()")
Reported-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Link: https://lore.kernel.org/all/CAK8fFZ7MKoFSEzMBDAOjoUt+vTZRRQgLDNXEOfdCCXSoXXKE0g@mail.gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like previous patch does in TCP, we need to adhere to RFC 1213:
"tcpCurrEstab OBJECT-TYPE
...
The number of TCP connections for which the current state
is either ESTABLISHED or CLOSE- WAIT."
So let's consider CLOSE-WAIT sockets.
The logic of counting
When we increment the counter?
a) Only if we change the state to ESTABLISHED.
When we decrement the counter?
a) if the socket leaves ESTABLISHED and will never go into CLOSE-WAIT,
say, on the client side, changing from ESTABLISHED to FIN-WAIT-1.
b) if the socket leaves CLOSE-WAIT, say, on the server side, changing
from CLOSE-WAIT to LAST-ACK.
Fixes: d9cd27b8cd ("mptcp: add CurrEstab MIB counter support")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC 1213, we should also take CLOSE-WAIT sockets into
consideration:
"tcpCurrEstab OBJECT-TYPE
...
The number of TCP connections for which the current state
is either ESTABLISHED or CLOSE- WAIT."
After this, CurrEstab counter will display the total number of
ESTABLISHED and CLOSE-WAIT sockets.
The logic of counting
When we increment the counter?
a) if we change the state to ESTABLISHED.
b) if we change the state from SYN-RECEIVED to CLOSE-WAIT.
When we decrement the counter?
a) if the socket leaves ESTABLISHED and will never go into CLOSE-WAIT,
say, on the client side, changing from ESTABLISHED to FIN-WAIT-1.
b) if the socket leaves CLOSE-WAIT, say, on the server side, changing
from CLOSE-WAIT to LAST-ACK.
Please note: there are two chances that old state of socket can be changed
to CLOSE-WAIT in tcp_fin(). One is SYN-RECV, the other is ESTABLISHED.
So we have to take care of the former case.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_redbox.sh test need to create bridge for testing. Add the missing
config CONFIG_BRIDGE in config file.
Fixes: eafbf0574e ("test: hsr: Extend the hsr_redbox.sh to have more SAN devices connected")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f58f45c1e5 ("vxlan: drop packets from invalid src-address")
has recently been added to vxlan mainly in the context of source
address snooping/learning so that when it is enabled, an entry in the
FDB is not being created for an invalid address for the corresponding
tunnel endpoint.
Before commit f58f45c1e5 vxlan was similarly behaving as geneve in
that it passed through whichever macs were set in the L2 header. It
turns out that this change in behavior breaks setups, for example,
Cilium with netkit in L3 mode for Pods as well as tunnel mode has been
passing before the change in f58f45c1e5 for both vxlan and geneve.
After mentioned change it is only passing for geneve as in case of
vxlan packets are dropped due to vxlan_set_mac() returning false as
source and destination macs are zero which for E/W traffic via tunnel
is totally fine.
Fix it by only opting into the is_valid_ether_addr() check in
vxlan_set_mac() when in fact source address snooping/learning is
actually enabled in vxlan. This is done by moving the check into
vxlan_snoop(). With this change, the Cilium connectivity test suite
passes again for both tunnel flavors.
Fixes: f58f45c1e5 ("vxlan: drop packets from invalid src-address")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Bauer <mail@david-bauer.net>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
q->bands will be assigned to qopt->bands to execute subsequent code logic
after kmalloc. So the old q->bands should not be used in kmalloc.
Otherwise, an out-of-bounds write will occur.
Fixes: c2999f7fb0 ("net: sched: multiq: don't call qdisc_put() while holding tree lock")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8061 needs to write to a MMD register at driver initialization to fix
an errata. This worked in 5.0 kernel but not in newer kernels. The
issue is the main phylib code no longer resets PHY at the very beginning.
Calling phy resuming code later will reset the chip if it is already
powered down at the beginning. This wipes out the MMD register write.
Solution is to implement a phy resume function for KSZ8061 to take care
of this problem.
Fixes: 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When copying smc settings to clcsock, avoid setting clcsock's sk_sndbuf
to sysctl_tcp_wmem[1], since this may overwrite the value set by
tcp_sndbuf_expand() in TCP connection establishment.
And the other setting sk_{snd|rcv}buf to sysctl value in
smc_adjust_sock_bufsizes() can also be omitted since the initialization
of smc sock and clcsock has set sk_{snd|rcv}buf to smc.sysctl_{w|r}mem
or ipv4_sysctl_tcp_{w|r}mem[1].
Fixes: 30c3c4a449 ("net/smc: Use correct buffer sizes when switching between TCP and SMC")
Link: https://lore.kernel.org/r/5eaf3858-e7fd-4db8-83e8-3d7a3e0e9ae2@linux.alibaba.com
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>, too.
Signed-off-by: David S. Miller <davem@davemloft.net>
PF mcam entries has to be at low priority always so that VF
can install longest prefix match rules at higher priority.
This was taken care currently but when priority allocation
wrt reference entry is requested then entries are allocated
from mid-zone instead of low priority zone. Fix this and
always allocate entries from low priority zone for PFs.
Fixes: 7df5b4b260 ("octeontx2-af: Allocate low priority entries for PF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2863d665ea.
This patch introduced a potential kernel crash when multiple napi instances
redirect to the same AF_XDP socket. By removing the queue_index check, it is
possible for multiple napi instances to access the Rx ring at the same time,
which will result in a corrupted ring state which can lead to a crash when
flushing the rings in __xsk_flush(). This can happen when the linked list of
sockets to flush gets corrupted by concurrent accesses. A quick and small fix
is not possible, so let us revert this for now.
Reported-by: Yuval El-Hanany <YuvalE@radware.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/xdp-newbies/8100DBDC-0B7C-49DB-9995-6027F6E63147@radware.com
Link: https://lore.kernel.org/bpf/20240604122927.29080-2-magnus.karlsson@gmail.com
For TLS offload we mark packets with skb->decrypted to make sure
they don't escape the host without getting encrypted first.
The crypto state lives in the socket, so it may get detached
by a call to skb_orphan(). As a safety check - the egress path
drops all packets with skb->decrypted and no "crypto-safe" socket.
The skb marking was added to sendpage only (and not sendmsg),
because tls_device injected data into the TCP stack using sendpage.
This special case was missed when sendpage got folded into sendmsg.
Fixes: c5c37af6ec ("tcp: Convert do_tcp_sendpages() to use MSG_SPLICE_PAGES")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240530232607.82686-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The first fixes for v6.10. And we have a big one, I suspect the
biggest wireless pull request we ever had. There are fixes all over,
both in stack and drivers. Likely the most important here are mt76 not
working on mt7615 devices, ath11k not being able to connect to 6 GHz
networks and rtlwifi suffering from packet loss. But of course there's
much more.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZdrSMRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuYnAgAqZMvSQKbhkYRfIua9Ygmdk8pDetEhaJg
HAUiW8ymLkWG1Md1V3tjY9Es66YeSr03Tx8xz/8pDWSaiUCdCs+u0zonhRK0sb3/
HAfyUpRIGDq/9kTM9lfL+yOTKwtRti+NmTXqeJr1CrpBejuXydRT+YYcIEmwQQxw
pm5xwLmrq74pMRE3VCTRbj2mfv/leFoDQasTeimUi6PgRrCeXSmUDy14k1zyAsI5
/uchvyvhgN54U2vIvO0RzW5zfS84cNEG+mW/+PpiuMftH2sYS1/UqT8BCQdrfzBz
PuiocUBXU68NzB4iLZhzPSDirOsYVaYpgKPfLPF1jNoj+iEQh1HhCA==
=5my7
-----END PGP SIGNATURE-----
Merge tag 'wireless-2024-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.10-rc3
The first fixes for v6.10. And we have a big one, I suspect the
biggest wireless pull request we ever had. There are fixes all over,
both in stack and drivers. Likely the most important here are mt76 not
working on mt7615 devices, ath11k not being able to connect to 6 GHz
networks and rtlwifi suffering from packet loss. But of course there's
much more.
* tag 'wireless-2024-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (37 commits)
wifi: rtlwifi: Ignore IEEE80211_CONF_CHANGE_RETRY_LIMITS
wifi: mt76: mt7615: add missing chanctx ops
wifi: wilc1000: document SRCU usage instead of SRCU
Revert "wifi: wilc1000: set atomic flag on kmemdup in srcu critical section"
Revert "wifi: wilc1000: convert list management to RCU"
wifi: mac80211: fix UBSAN noise in ieee80211_prep_hw_scan()
wifi: mac80211: correctly parse Spatial Reuse Parameter Set element
wifi: mac80211: fix Spatial Reuse element size check
wifi: iwlwifi: mvm: don't read past the mfuart notifcation
wifi: iwlwifi: mvm: Fix scan abort handling with HW rfkill
wifi: iwlwifi: mvm: check n_ssids before accessing the ssids
wifi: iwlwifi: mvm: properly set 6 GHz channel direct probe option
wifi: iwlwifi: mvm: handle BA session teardown in RF-kill
wifi: iwlwifi: mvm: Handle BIGTK cipher in kek_kck cmd
wifi: iwlwifi: mvm: remove stale STA link data during restart
wifi: iwlwifi: dbg_ini: move iwl_dbg_tlv_free outside of debugfs ifdef
wifi: iwlwifi: mvm: set properly mac header
wifi: iwlwifi: mvm: revert gen2 TX A-MPDU size to 64
wifi: iwlwifi: mvm: d3: fix WoWLAN command version lookup
wifi: iwlwifi: mvm: fix a crash on 7265
...
====================
Link: https://lore.kernel.org/r/20240603115129.9494CC2BD10@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in lib/test_rhashtable.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240531-md-lib-test_rhashtable-v1-1-cd6d4138f1b6@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
dst_cache: fix possible races
This series is inspired by various undisclosed syzbot
reports hinting at corruptions in dst_cache structures.
It seems at least four users of dst_cache are racy against
BH reentrancy.
Last patch is adding a DEBUG_NET check to catch future misuses.
====================
Link: https://lore.kernel.org/r/20240531132636.2637995-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After fixing four different bugs involving dst_cache
users, it might be worth adding a check about BH being
blocked by dst_cache callers.
DEBUG_NET_WARN_ON_ONCE(!in_softirq());
It is not fatal, if we missed valid case where no
BH deadlock is to be feared, we might change this.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
ila_output() is called from lwtunnel_output()
possibly from process context, and under rcu_read_lock().
We might be interrupted by a softirq, re-enter ila_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in seg6_output_core() is not good enough,
because seg6_output_core() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter seg6_output_core()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Apply a similar change in seg6_input_core().
Fixes: fa79581ea6 ("ipv6: sr: fix several BUGs when preemption is enabled")
Fixes: 6c8702c60b ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Lebrun <dlebrun@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in rpl_output() is not good enough,
because rpl_output() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter rpl_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Apply a similar change in rpl_input().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Aring <aahringo@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in ioam6_output() is not good enough,
because ioam6_output() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter ioam6_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Fixes: 8cb3bf8bff ("ipv6: ioam: Add support for the ip6ip6 encapsulation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Justin Iurman <justin.iurman@uliege.be>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 1a80dbcb2d, bpf_link can be freed by
link->ops->dealloc_deferred, but the code still tests and uses
link->ops->dealloc afterward, which leads to a use-after-free as
reported by syzbot. Actually, one of them should be sufficient, so
just call one of them instead of both. Also add a WARN_ON() in case
of any problematic implementation.
Fixes: 1a80dbcb2d ("bpf: support deferring bpf_link dealloc to after RCU grace period")
Reported-by: syzbot+1989ee16d94720836244@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20240602182703.207276-1-xiyou.wangcong@gmail.com
The iterator variable dst cannot be NULL and the if check can be removed.
Remove it and fix the following Coccinelle/coccicheck warning reported
by itnull.cocci:
ERROR: iterator variable bound on line 762 cannot be NULL
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20240529101900.103913-2-thorsten.blum@toblux.com
When the PHY is powered up after powered down most of the registers are
reset, so the PHY setup code needs to be done again. In addition the
interrupt register will need to be setup again so that link status
indication works again.
Fixes: 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata fixes to PHY driver")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_CLOSE may or may not have current/rnext keys and should not be
considered "established". The fast-path for TCP_CLOSE is
SKB_DROP_REASON_TCP_CLOSE. This is what tcp_rcv_state_process() does
anyways. Add an early drop path to not spend any time verifying
segment signatures for sockets in TCP_CLOSE state.
Cc: stable@vger.kernel.org # v6.7
Fixes: 0a3a809089 ("net/tcp: Verify inbound TCP-AO signed segments")
Signed-off-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20240529-tcp_ao-sk_state-v1-1-d69b5d323c52@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently NCSI driver will send several NCSI commands back to back without
waiting the response of previous NCSI command or timeout in some state
when NIC have multi channel. This operation against the single thread
manner defined by NCSI SPEC(section 6.3.2.3 in DSP0222_1.1.1)
According to NCSI SPEC(section 6.2.13.1 in DSP0222_1.1.1), we should probe
one channel at a time by sending NCSI commands (Clear initial state, Get
version ID, Get capabilities...), than repeat this steps until the max
number of channels which we got from NCSI command (Get capabilities) has
been probed.
Fixes: e6f44ed6d0 ("net/ncsi: Package and channel management")
Signed-off-by: DelphineCCChiu <delphine_cc_chiu@wiwynn.com>
Link: https://lore.kernel.org/r/20240529065856.825241-1-delphine_cc_chiu@wiwynn.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The object "ax25_dev" is managed by reference counting. Thus it should
not be directly released by kfree(), replace with ax25_dev_put().
Fixes: d01ffb9eee ("ax25: add refcount in ax25_dev to avoid UAF bugs")
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240530051733.11416-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When releasing a socket in ax25_release(), we call netdev_put() to
decrease the refcount on the associated ax.25 device. However, the
execution path for accepting an incoming connection never calls
netdev_hold(). This imbalance leads to refcount errors, and ultimately
to kernel crashes.
A typical call trace for the above situation will start with one of the
following errors:
refcount_t: decrement hit 0; leaking memory.
refcount_t: underflow; use-after-free.
And will then have a trace like:
Call Trace:
<TASK>
? show_regs+0x64/0x70
? __warn+0x83/0x120
? refcount_warn_saturate+0xb2/0x100
? report_bug+0x158/0x190
? prb_read_valid+0x20/0x30
? handle_bug+0x3e/0x70
? exc_invalid_op+0x1c/0x70
? asm_exc_invalid_op+0x1f/0x30
? refcount_warn_saturate+0xb2/0x100
? refcount_warn_saturate+0xb2/0x100
ax25_release+0x2ad/0x360
__sock_release+0x35/0xa0
sock_close+0x19/0x20
[...]
On reboot (or any attempt to remove the interface), the kernel gets
stuck in an infinite loop:
unregister_netdevice: waiting for ax0 to become free. Usage count = 0
This patch corrects these issues by ensuring that we call netdev_hold()
and ax25_dev_hold() for new connections in ax25_accept(). This makes the
logic leading to ax25_accept() match the logic for ax25_bind(): in both
cases we increment the refcount, which is ultimately decremented in
ax25_release().
Fixes: 9fd75b66b8 ("ax25: Fix refcount leaks caused by ax25_cb_del()")
Signed-off-by: Lars Kellogg-Stedman <lars@oddbit.com>
Tested-by: Duoming Zhou <duoming@zju.edu.cn>
Tested-by: Dan Cross <crossd@gmail.com>
Tested-by: Chris Maness <christopher.maness@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/20240529210242.3346844-2-lars@oddbit.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heng Qi says:
====================
virtio_net: fix lock warning and unrecoverable state
Patch 1 describes and fixes an issue where dim cannot return to
normal state in certain scenarios.
Patch 2 attempts to resolve lockdep's complaints that holding many
nested locks.
====================
Link: https://lore.kernel.org/r/20240528134116.117426-1-hengqi@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the following snippet is run, lockdep will report a deadlock[1].
/* Acquire all queues dim_locks */
for (i = 0; i < vi->max_queue_pairs; i++)
mutex_lock(&vi->rq[i].dim_lock);
There's no deadlock here because the vq locks are always taken
in the same order, but lockdep can not figure it out. So refactoring
the code to alleviate the problem.
[1]
========================================================
WARNING: possible recursive locking detected
6.9.0-rc7+ #319 Not tainted
--------------------------------------------
ethtool/962 is trying to acquire lock:
but task is already holding lock:
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&vi->rq[i].dim_lock);
lock(&vi->rq[i].dim_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by ethtool/962:
#0: ffffffff82dbaab0 (cb_lock){++++}-{3:3}, at: genl_rcv+0x19/0x40
#1: ffffffff82dad0a8 (rtnl_mutex){+.+.}-{3:3}, at:
ethnl_default_set_doit+0xbe/0x1e0
stack backtrace:
CPU: 6 PID: 962 Comm: ethtool Not tainted 6.9.0-rc7+ #319
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x79/0xb0
check_deadlock+0x130/0x220
__lock_acquire+0x861/0x990
lock_acquire.part.0+0x72/0x1d0
? lock_acquire+0xf8/0x130
__mutex_lock+0x71/0xd50
virtnet_set_coalesce+0x151/0x190
__ethnl_set_coalesce.isra.0+0x3f8/0x4d0
ethnl_set_coalesce+0x34/0x90
ethnl_default_set_doit+0xdd/0x1e0
genl_family_rcv_msg_doit+0xdc/0x130
genl_family_rcv_msg+0x154/0x230
? __pfx_ethnl_default_set_doit+0x10/0x10
genl_rcv_msg+0x4b/0xa0
? __pfx_genl_rcv_msg+0x10/0x10
netlink_rcv_skb+0x5a/0x110
genl_rcv+0x28/0x40
netlink_unicast+0x1af/0x280
netlink_sendmsg+0x20e/0x460
__sys_sendto+0x1fe/0x210
? find_held_lock+0x2b/0x80
? do_user_addr_fault+0x3a2/0x8a0
? __lock_release+0x5e/0x160
? do_user_addr_fault+0x3a2/0x8a0
? lock_release+0x72/0x140
? do_user_addr_fault+0x3a7/0x8a0
__x64_sys_sendto+0x29/0x30
do_syscall_64+0x78/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fixes: 4d4ac2ecec ("virtio_net: Add a lock for per queue RX coalesce")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20240528134116.117426-3-hengqi@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the dim worker is scheduled, if it no longer needs to issue
commands, dim may not be able to return to the working state later.
For example, the following single queue scenario:
1. The dim worker of rxq0 is scheduled, and the dim status is
changed to DIM_APPLY_NEW_PROFILE;
2. dim is disabled or parameters have not been modified;
3. virtnet_rx_dim_work exits directly;
Then, even if net_dim is invoked again, it cannot work because the
state is not restored to DIM_START_MEASURE.
Fixes: 6208799553 ("virtio-net: support rx netdim")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240528134116.117426-2-hengqi@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Statistic values should be set to ETHTOOL_STAT_NOT_SET even if the
device doesn't support statistics. Otherwise zeros will be returned as
if they are proper values:
host# ethtool -I -T lo
Time stamping parameters for lo:
Capabilities:
software-transmit
software-receive
software-system-clock
PTP Hardware Clock: none
Hardware Transmit Timestamp Modes: none
Hardware Receive Filter Modes: none
Statistics:
tx_pkts: 0
tx_lost: 0
tx_err: 0
Fixes: 0e9c127729 ("ethtool: add interface to read Tx hardware timestamping statistics")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Link: https://lore.kernel.org/r/20240530040814.1014446-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Motorcomm PHY driver is now maintained by the OEM. The driver has
expanded far beyond my original purpose, and I do not have the hardware
to test against the new portions of it. Therefore I am removing myself as
a maintainer of the driver.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20240529185635.538072-1-pgwipeout@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactored the handling of control_buf to be within the cvq_lock
critical section, mitigating race conditions between reading device
responses and new command submissions.
Fixes: 6f45ab3e04 ("virtio_net: Add a lock for the command VQ.")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240530034143.19579-1-hengqi@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 0a44dfc070 ("wifi: mac80211: simplify non-chanctx
drivers") ieee80211_hw_config() is no longer called with changed = ~0.
rtlwifi relied on ~0 in order to ignore the default retry limits of
4/7, preferring 48/48 in station mode and 7/7 in AP/IBSS.
RTL8192DU has a lot of packet loss with the default limits from
mac80211. Fix it by ignoring IEEE80211_CONF_CHANGE_RETRY_LIMITS
completely, because it's the simplest solution.
Link: https://lore.kernel.org/linux-wireless/cedd13d7691f4692b2a2fa5a24d44a22@realtek.com/
Cc: stable@vger.kernel.org # 6.9.x
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/1fabb8e4-adf3-47ae-8462-8aea963bc2a5@gmail.com
Commit f236464f1d ("wifi: wilc1000: convert list management to RCU")
attempted to convert SRCU to RCU usage, assuming it was not really needed.
The runtime issues that arose after merging it showed that there are code
paths involving sleeping functions, and removing those would need some
heavier driver rework.
Add some documentation about SRCU need to make sure that any future
developer do not miss some use cases if tempted to convert back again to
RCU.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240528-wilc_revert_srcu_to_rcu-v1-3-bce096e0798c@bootlin.com
