Otherwise each driver would need to keep the information inside
their own framebuffer object structure. Also add offsets[]. BOs
on the other hand are driver specific, so those can be kept in
driver specific structures.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My EFI BIOS starts the graphics card up in my projector's preferred EDID
mode, 1080@60i. The Intel driver does not clear all the interlaced bits.
This patch introduces a new PIPECONF_INTERLACE_MASK define and uses it
to restore progressive mode.
Signed-of-by: Christian Schmidt <schmidt@digadd.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Name the formats as DRM_FORMAT_X instead of DRM_FOURCC_X. Use consistent
names, especially for the RGB formats. Component order and byte order are
now strictly specified for each format.
The RGB format naming follows a convention where the components names
and sizes are listed from left to right, matching the order within a
single pixel from most significant bit to least significant bit.
The YUV format names vary more. For the 4:2:2 packed formats and 2
plane formats use the fourcc. For the three plane formats the
name includes the plane order and subsampling information using the
standard subsampling notation. Some of those also happen to match
the official fourcc definition.
The fourccs for for all the RGB formats and some of the YUV formats
I invented myself. The idea was that looking at just the fourcc you
get some idea what the format is about without having to decode it
using some external reference.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To properly support the various plane formats supported by different
hardware, the kernel must know the pixel format of a framebuffer object.
So add a new ioctl taking a format argument corresponding to a fourcc
name from the new drm_fourcc.h header file. Implement the fb creation
hooks in terms of the new mode_fb_cmd2 using helpers where the old
bpp/depth values are needed.
v2: create DRM specific fourcc header file for sharing with libdrm etc
v3: fix rebase failure and use DRM fourcc codes in intel_display.c and
update commit message
v4: make fb_cmd2 handle field into an array for multi-object formats
pull in Ville's fix for the memcpy in drm_plane_init
apply Ville's cleanup to zero out fb_cmd2 arg in drm_mode_addfb
v5: add 'flags' field for interlaced support (from Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Belongs in PCH enable instead. The duplication is worrying and the
specs explicitly list transcoder select *after* actual PLL enable, which
doesn't occur until later.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The watermark reg for the third pipe is in an unusual offset; add
support for it and set watermarks for 3 pipe configs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
At the point where we check, we can't do much about the failure, but it
can aid debugging. Note that the auto-train override bit will be reset
as part of normal mode setting with this patch if a pipe ever does get
stuck, but that's consistent with the workaround for CPT provided by the
hardware team. This patch helped catch the fact that the pipe wasn't
running in the !composite sync FDI case on my IVB SDV, so has already
shown to be useful.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Transcoder A will always use PLL A and transcoder B will use PLL B. But
transcoder C could use either, so always mask the select bits off before
or'ing in a new value.
Reported-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The cursor regs have moved around, add the offsets and new macros for
getting at them.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We can have more than just A and B these days.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add two new fields to the intel_crtc struct for 3 pipe support: no_pll
and use_pll_a. The no_pll field is only set on the 3rd pipe to indicate
that it doesn't have a PLL of its own and so shouldn't try to write the
main PLL regs. The use_pll_a field controls which PLL pipe 3 will
share, A or B. The core code will try to share PLLs with whichever pipe
has the same timings, rejecting the mode set if none is found. This
means that pipe 3 must always be set after one of the other pipes has
been configured with real PLL settings.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add a couple of checks now that we're using the 3rd transcoder:
1) make sure the transcoder PLL enable bit is set for the transcoder
in question
2) when checking actual PLL enable, use the selected PLL number rather
than the transcoder number (they could be different now)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Just a cleanup to make the mode_set function more manageable.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Well almost anyway. IVB has 3 planes, pipes, transcoders, and FDI
interfaces, but only 2 pipe PLLs. So two of the pipes must use the same
pipe timings (e.g. 2 DP plus one other, or two HDMI with the same mode
and one other, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add a macro for accessing the two pipe PLLs and add a check to make sure
we don't access a non-existent one in the enable/disable functions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-By: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
It's needed for 3 pipe support as well as just regular functionality
(e.g. DisplayPort).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Adam Jackson <ajax@redhat.com>
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The rps disabling code wasn't properly cancelling outstanding work
items. Also add a comment that explains why we're not racing with
the work item that could unmask interrupts - that piece of code
confused me quite a bit.
v2: Ben Widawsky pointed out that the first patch would deadlock
(and a few lesser problems). All corrected.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
The reference clock configuration must be done before any mode setting
can occur as all outputs must be disabled to change
anything. Initialize the clocks after turning everything off during
the initialization process.
Also, re-initialize the refclk at resume time.
Signed-off-by: Keith Packard <keithp@keithp.com>
I can't find any reference clocks which run at 96MHz as seems to be
indicated from the comments in this code.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
When trying to use SSC on Ibex Peak without CK505, any non-SSC outputs
(like VGA or TV) get broken. So, do not use SSC on Ibex Peak unless
there is a CK505 available (as specified by the VBT).
On Cougar Point, all clocking is internal, so SSC can always be used,
and there will never be a CK505 available.
This eliminates VGA shimmer on some Ironlake machines which have a
CK505 clock source.
References: https://bugzilla.kernel.org/show_bug.cgi?id=21742
References: https://bugs.freedesktop.org/show_bug.cgi?id=38750
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The PCH refclk settings are global, so we need to look at all of the
encoders, not just the current encoder when deciding how to configure
it. Also, handle systems with more than one panel (any combination of
PCH/non-PCH eDP and LVDS).
Disable SSC clocks when no panels are connected.
Signed-off-by: Keith Packard <keithp@keithp.com>
Allow SSC to be enabled even when the BIOS disables it for testing SSC paths.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Make the default FBC behaviour chipset specific, allowing us to turn
it on by default for Ironlake and older where it has been seen to
cause trouble with screen updates.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Francis Moreau <francis.moro@gmail.com>
Add ELD support for Intel Eaglelake, IbexPeak/Ironlake,
SandyBridge/CougarPoint and IvyBridge/PantherPoint chips.
ELD (EDID-Like Data) describes to the HDMI/DP audio driver the audio
capabilities of the plugged monitor. It's built and passed to audio
driver in 2 steps:
(1) at get_modes time, parse EDID and save ELD to drm_connector.eld[]
(2) at mode_set time, write drm_connector.eld[] to the Transcoder's hw
ELD buffer and set the ELD_valid bit to inform HDMI/DP audio driver
This patch is tested OK on G45/HDMI, IbexPeak/HDMI and IvyBridge/HDMI+DP.
Test scheme: plug in the HDMI/DP monitor, and run
cat /proc/asound/card0/eld*
to check if the monitor name, HDMI/DP type, etc. show up correctly.
Minor imperfection: the GEN5_AUD_CNTL_ST/DIP_Port_Select field always
reads 0 (reserved). Without knowing the port number, I worked it around
by setting the ELD_valid bit for ALL the three ports. It's tested to not
be a problem, because the audio driver will find invalid ELD data and
hence rightfully abort, even when it sees the ELD_valid indicator.
Thanks to Zhenyu and Pierre-Louis for a lot of valuable help and testing.
CC: Zhao Yakui <yakui.zhao@intel.com>
CC: Wang Zhenyu <zhenyu.z.wang@intel.com>
CC: Jeremy Bush <contractfrombelow@gmail.com>
CC: Christopher White <c.white@pulseforce.com>
CC: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
CC: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We want to enable dithering on any pipe where the frame buffer has
more color resolution than the output device.
The previous code was incorrectly clamping the frame buffer bpc to the
display bpc, effectively disabling dithering all of the time as the
computed frame buffer bpc would never be larger than the display bpc.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
We want to enable dithering on any pipe where the frame buffer has
more color resolution than the output device.
The previous code was incorrectly clamping the frame buffer bpc to the
display bpc, effectively disabling dithering all of the time as the
computed frame buffer bpc would never be larger than the display bpc.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Otherwise it just contains random memory.
Issue detected by cppcheck.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The commit "Not all systems expose a firmware or platform mechanism for
changing the backlight intensity on i915, so add native driver support"
adds calls to intel_panel_setup_backlight() from intel_{lvds,dp}_init
so do not call it again from intel_setup_outputs().
BugLink: http://bugs.launchpad.net/bugs/831542
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
ACKed-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We ought to be calling this from our DPMS routines as well as global
state may change and we need to enable/disable clocks. So split out the
code in preparation for further changes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Just an extra parameter which isn't actually needed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CPT pipe select is different from previous generations (using two bits
instead of one). All of the paths from intel_disable_pch_ports were
not making this distinction.
Mode setting with pipe A turned off would then also force all outputs
on pipe B to get turned off as the disable code would mistakenly
decide that all of these outputs were on pipe A and turn them off.
This is an extension of the CPT DP disable fix (why didn't I fix this then?)
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The EDID parser will zero out the bpc value, and the driver needs to handle
that case. In our picker, we'll just ignore 0 values as far as bpp
picking goes.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=39323.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
These bits moved around on SNB and above.
v2: again with the git send-email fail
v3: add macros for getting per-pipe override & enable bits
v4: enable phase sync pointer on SNB and IVB configs as well
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Using the new quirk added to support disabling SSC on Lenovo U160
(#36656, commit 435793dfb8), also register
the Vaio as a special case and disable SSC for it.
This patch fixes#34437 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=34437
Signed-off-by: Michel Alexandre Salim <salimma@fedoraproject.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
If a mode set fails we may get a message from drm_crtc_helper if we're lucky,
but it won't tell us anything about *why* we failed to set a mode. So
add a few DRM_ERRORs for the cases that shouldn't happen so we can debug
things more easily.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
CB tuning is needed to handle potential process variations that might
cause clock jitter for certain PLL settings. However, we were setting
it incorrectly since we were using the wrong M value as a check (M1 when
we needed to use the whole M value). Fix it up, making my HDMI
attached display a little prettier (used to have occasional dots crawl
across the display).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Writes to the plane control register are buffered in the chip until a
write to the DSPADDR (pre-965) or DSPSURF (post-965) register occurs.
This patch adds flushes in:
intel_enable_plane
gen6_init_clock_gating
ivybridge_init_clock_gating
Signed-off-by: Keith Packard <keithp@keithp.com>
After writing to the plane control reg we need to write to the surface
reg to trigger the double buffered register latch. On previous
chipsets, writing to DSPADDR was enough, but on ILK+ DSPSURF is the reg
that triggers the double buffer latch.
v2: write DSPADDR too to cover pre-965 chipsets
v3: use flush_display_plane instead, that's what it's for
v4: send the right patch
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On CougarPoint and PantherPoint PCH chips, the timing generator may fail
to start after DP training completes. This is due to a bug in the
FDI autotraining detect logic (which will stall the timing generator and
re-enable it once training completes), so disable it to avoid silent DP
mode setting failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This corrects the DPMS mode tracking so that the DPMS code will
actually turn the CRTC off the next time the screen saves.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Display port pipe selection on CPT is not done with a bit in the
output register, rather it is controlled by a couple of bits in the
separate transcoder register which indicate which display port output
is connected to the transcoder.
This patch replaces the simplistic macro DP_PIPE_ENABLED with the
rather more complicated function dp_pipe_enabled which checks the
output register to see if that is enabled, and then goes on to either
check the output register pipe selection bit (on non-CPT) or the
transcoder DP selection bits (on CPT).
Before this patch, any time the mode of pipe A was changed, any
display port outputs on pipe B would get disabled as
intel_disable_pch_ports would ensure that the mode setting operation
could occur on pipe A without interference from other outputs
connected to that pch port
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
If a mode set fails we may get a message from drm_crtc_helper if we're lucky,
but it won't tell us anything about *why* we failed to set a mode. So
add a few DRM_ERRORs for the cases that shouldn't happen so we can debug
things more easily.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
