Mali DP hardware has a 'go' bit (config_valid) for making the new scene
parameters active at the next page flip. The problem with the current
code is that the driver first sets this bit and then proceeds to wait
for confirmation from the hardware that the configuration has been
updated before arming the vblank event. As config_valid is actually
asserted by the hardware after the vblank event, during the prefetch
phase, when we get to arming the vblank event we are going to send it
at the next vblank, in effect halving the vblank rate from the userspace
perspective.
Fix it by sending the userspace event from the IRQ handler, when we
handle the config_valid interrupt, which syncs with the time when the
hardware is active with the new parameters.
Reported-by: Alexandru-Cosmin Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali dp needs to disable pixel alpha blending (use layer alpha blending) to
display color formats that do not contain alpha bits per pixel
This patch depends on:
"[PATCH v2 01/19] drm/fourcc: Add a alpha field to drm_format_info"
Signed-off-by: Ayan Kumar Halder <ayan.halder@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
In the case, when the user wants to scale and rotate a layer by 90/270
degrees, the scaling engine input dimensions' parameters ie width and
height needs to be swapped with respect to the layer's input dimensions.
This means scaling engine input height should be set to layer's input
width and scaling engine input width should be set to
layer's input height.
Signed-off-by: Ayan Halder <ayan.halder@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Currently the scaling engine gets enabled for a plane where the input
size differs from the composition size. As rotation is done natively
by the plane's hardware layer, we don't need the scaling engine to be
enabled.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP hardware needs pitch line sizes aligned to the bus burst
size for reads, so take that into consideration when allocating dumb
buffers. If the layer is rotated then the stride size requirement is
even larger for some hardware versions, so allocate for the worst case
scenario. Update the ->dumb_create() hook to a driver specific function
that sets the correct pitch size.
Reported-by: Ayan Halder <ayan.halder@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Rotated planes need a pitch size that is aligned to 8 bytes
for older DP500 and DP550 and at least 64 bytes for DP650. Replace
the malidp_hw_pitch_valid() function with one that calculates
the correct pitch alignment to take into account rotation.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Like many other panel drivers, this one fails to build when backlight
support is disabled:
drivers/gpu/drm/panel/panel-raydium-rm68200.o: In function `rm68200_probe':
panel-raydium-rm68200.c:(.text+0x14a): undefined reference to `devm_of_find_backlight'
This adds the appropriate dependency.
Note that while include/linux/backlight.h provides a stub inline when
backlight support is not enabled, this isn't enough to deal with the
case where backlight support is built as a module but the panel driver
is built-in, in which case linking will still fail as above.
One way to avoid this is to add a dependency such as this:
depends on BACKLIGHT_CLASS_DEVICE || BACKLIGHT_CLASS_DEVICE=n
but that is rather complex and misses the point that the panel support
is mostly useless without backlight support.
Fixes: 2b7ed18bed ("drm/panel: Add support for Raydium RM68200 panel driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[treding@nvidia.com: clarify the need for the dependency]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313210015.3344380-1-arnd@arndb.de
When CONFIG_OMAP2_DSS_DPI is disabled, compilation fails due to:
drivers/gpu/drm/omapdrm/dss/dss.h:388:25: error: conflicting types for ‘port’
struct device_node *port,
^~~~
Fix this by renaming the first parameter correctly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When compiling with CONFIG_OMAP2_DSS_DEBUGFS disabled, build fails due
to:
drivers/gpu/drm/omapdrm/dss/dss.c:1474:10: error: ‘dss_debug_dump_clocks’ undeclared (first use in this function); did you mean ‘dispc_dump_clocks’?
dss_debug_dump_clocks, dss);
^~~~~~~~~~~~~~~~~~~~~
dispc_dump_clocks
Fix this by moving the required functions outside #if
defined(CONFIG_OMAP2_DSS_DEBUGFS).
In the long term, we perhaps want to try to get all the debugfs support
left out if debugfs is not enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Handle both positive and negative dclk polarity,
according to bus_flags, taking care of this:
On A20 and similar SoCs, the only way to achieve Positive Edge
(Rising Edge), is setting dclk clock phase to 2/3(240°).
By default TCON works in Negative Edge(Falling Edge), this is why phase
is set to 0 in that case.
Unfortunately there's no way to logically invert dclk through IO_POL
register.
The only acceptable way to work, triple checked with scope,
is using clock phase set to 0° for Negative Edge and set to 240° for
Positive Edge.
On A33 and similar SoCs there would be a 90° phase option, but it divides
also dclk by 2.
This patch is a way to avoid quirks all around TCON and DOTCLOCK drivers
for using A33 90° phase divided by 2 and consequently increase code
complexity.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520963677-124239-1-git-send-email-giulio.benetti@micronovasrl.com
UAPI Changes:
- Query uAPI interface (used for GPU topology information currently)
* Mesa: https://patchwork.freedesktop.org/series/38795/
Driver Changes:
- Increase PSR2 size for CNL (DK)
- Avoid retraining LSPCON link unnecessarily (Ville)
- Decrease request signaling latency (Chris)
- GuC error capture fix (Daniele)
* tag 'drm-intel-next-2018-03-08' of git://anongit.freedesktop.org/drm/drm-intel: (127 commits)
drm/i915: Update DRIVER_DATE to 20180308
drm/i915: add schedule out notification of preempted but completed request
drm/i915: expose rcs topology through query uAPI
drm/i915: add query uAPI
drm/i915: add rcs topology to error state
drm/i915/debugfs: add rcs topology entry
drm/i915/debugfs: reuse max slice/subslices already stored in sseu
drm/i915: store all subslice masks
drm/i915/guc: work around gcc-4.4.4 union initializer issue
drm/i915/cnl: Add Wa_2201832410
drm/i915/icl: Gen11 forcewake support
drm/i915/icl: Add Indirect Context Offset for Gen11
drm/i915/icl: Enhanced execution list support
drm/i915/icl: new context descriptor support
drm/i915/icl: Correctly initialize the Gen11 engines
drm/i915: Assert that the request is indeed complete when signaled from irq
drm/i915: Handle changing enable_fbc parameter at runtime better.
drm/i915: Track whether the DP link is trained or not
drm/i915: Nuke intel_dp->channel_eq_status
drm/i915: Move SST DP link retraining into the ->post_hotplug() hook
...
Major points for this pull request:
- Add dGPU support for amdkfd initialization code and queue handling. It's
not complete support since the GPUVM part is missing (the under debate stuff).
- Enable PCIe atomics for dGPU if present
- Various adjustments to the amdgpu<-->amdkfd interface for dGPUs
- Refactor IOMMUv2 code to allow loading amdkfd without IOMMUv2 in the system
- Add HSA process eviction code in case of system memory pressure
- Various fixes and small changes
* tag 'drm-amdkfd-next-2018-03-11' of git://people.freedesktop.org/~gabbayo/linux: (24 commits)
uapi: Fix type used in ioctl parameter structures
drm/amdkfd: Implement KFD process eviction/restore
drm/amdkfd: Add GPUVM virtual address space to PDD
drm/amdkfd: Remove unaligned memory access
drm/amdkfd: Centralize IOMMUv2 code and make it conditional
drm/amdgpu: Add submit IB function for KFD
drm/amdgpu: Add GPUVM memory management functions for KFD
drm/amdgpu: add amdgpu_sync_clone
drm/amdgpu: Update kgd2kfd_shared_resources for dGPU support
drm/amdgpu: Add KFD eviction fence
drm/amdgpu: Remove unused kfd2kgd interface
drm/amdgpu: Fix wrong mask in get_atc_vmid_pasid_mapping_pasid
drm/amdgpu: Fix header file dependencies
drm/amdgpu: Replace kgd_mem with amdgpu_bo for kernel pinned gtt mem
drm/amdgpu: remove useless BUG_ONs
drm/amdgpu: Enable KFD initialization on dGPUs
drm/amdkfd: Add dGPU device IDs and device info
drm/amdkfd: Add dGPU support to kernel_queue_init
drm/amdkfd: Add dGPU support to the MQD manager
drm/amdkfd: Add dGPU support to the device queue manager
...
drm-misc-next for 4.17:
UAPI Changes:
plane: Add color encoding/range properties (Jyri)
nouveau: Replace iturbt_709 property with color_encoding property (Ville)
Core Changes:
atomic: Move plane clipping into plane check helper (Ville)
property: Multiple new property checks/verification (Ville)
Driver Changes:
rockchip: Fixes & improvements for rk3399/chromebook plus (various)
sun4i: Add H3/H5 HDMI support (Jernej)
i915: Add support for limited/full-range ycbcr toggling (Ville)
pl111: Add bandwidth checking/limiting (Linus)
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
* tag 'drm-misc-next-2018-03-09-3' of git://anongit.freedesktop.org/drm/drm-misc: (85 commits)
drm/rockchip: Don't use atomic constructs for psr
drm/rockchip: analogix_dp: set psr activate/deactivate when enable/disable bridge
drm/rockchip: dw_hdmi: Move HDMI vpll clock enable to bind()
drm/rockchip: inno_hdmi: reorder clk_disable_unprepare call in unbind
drm/rockchip: inno_hdmi: Fix error handling path.
drm/rockchip: dw-mipi-dsi: Fix connector and encoder cleanup.
drm/nouveau: Replace the iturbt_709 prop with the standard COLOR_ENCODING prop
drm/pl111: Use max memory bandwidth for resolution
drm/bridge: sii902x: Retry status read after DDI I2C
drm/pl111: Handle the RealView variant separately
drm/pl111: Make the default BPP a per-variant variable
drm: simple_kms_helper: Fix .mode_valid() documentation
bridge: Elaborate a bit on dumb VGA bridges in Kconfig
drm/atomic: Add new reverse iterator over all plane state (V2)
drm: Reject bad property flag combinations
drm: Make property flags u32
drm/uapi: Deprecate DRM_MODE_PROP_PENDING
drm: WARN when trying to add enum value > 63 to a bitmask property
drm: WARN when trying add enum values to non-enum/bitmask properties
drm: Reject replacing property enum values
...
Back in 2013, runtime PM for GPUs with integrated HDA controller was
introduced with commits 0d69704ae3 ("gpu/vga_switcheroo: add driver
control power feature. (v3)") and 246efa4a07 ("snd/hda: add runtime
suspend/resume on optimus support (v4)").
Briefly, the idea was that the HDA controller is forced on and off in
unison with the GPU.
The original code is mostly still in place even though it was never a
100% perfect solution: E.g. on access to the HDA controller, the GPU
is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there
are no provisions to keep it resumed until access to the HDA controller
has ceased: The GPU autosuspends after 5 seconds, rendering the HDA
controller inaccessible.
Additionally, a kludge is required when hda_intel.c probes: It has to
check whether the GPU is powered down (check_hdmi_disabled()) and defer
probing if so.
However in the meantime (in v4.10) the driver core has gained a feature
called device links which promises to solve such issues in a clean way:
It allows us to declare a dependency from the HDA controller (consumer)
to the GPU (supplier). The PM core then automagically ensures that the
GPU is runtime resumed as long as the HDA controller's ->probe hook is
executed and whenever the HDA controller is accessed.
By default, the HDA controller has a dependency on its parent, a PCIe
Root Port. Adding a device link creates another dependency on its
sibling:
PCIe Root Port
^ ^
| |
| |
HDA ===> GPU
The device link is not only used for runtime PM, it also guarantees that
on system sleep, the HDA controller suspends before the GPU and resumes
after the GPU, and on system shutdown the HDA controller's ->shutdown
hook is executed before the one of the GPU. It is a complete solution.
Using this functionality is as simple as calling device_link_add(),
which results in a dmesg entry like this:
pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
The code for the GPU-governed audio power management can thus be removed
(except where it's still needed for legacy manual power control).
The device link is added in a PCI quirk rather than in hda_intel.c.
It is therefore legal for the GPU to runtime suspend to D3cold even if
the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL
is not enabled, for accesses to the HDA controller will cause the GPU to
wake up regardless if they're occurring outside of hda_intel.c (think
config space readout via sysfs).
Contrary to the previous implementation, the HDA controller's power
state is now self-governed, rather than GPU-governed, whereas the GPU's
power state is no longer fully self-governed. (The HDA controller needs
to runtime suspend before the GPU can.)
It is thus crucial that runtime PM is always activated on the HDA
controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which
is the default), lest the GPU stays awake. This is achieved by setting
the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME
flag on the HDA controller.
A side effect is that power consumption might be reduced if the GPU is
in use but the HDA controller is not, because the HDA controller is now
allowed to go to D3hot. Before, it was forced to stay in D0 as long as
the GPU was in use. (There is no reduction in power consumption on my
Nvidia GK107, but there might be on other chips.)
The code paths for legacy manual power control are adjusted such that
runtime PM is disabled during power off, thereby preventing the PM core
from resuming the HDA controller.
Note that the device link is not only added on vga_switcheroo capable
systems, but for *any* GPU with integrated HDA controller. The idea is
that the HDA controller streams audio via connectors located on the GPU,
so the GPU needs to be on for the HDA controller to do anything useful.
This commit implicitly fixes an unbalanced runtime PM ref upon unbind of
hda_intel.c: On ->probe, a runtime PM ref was previously released under
the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but
on ->remove a runtime PM ref was only acquired under the first of those
conditions. Thus, binding and unbinding the driver twice on a
vga_switcheroo capable system caused the runtime PM refcount to drop
below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag
is now always set if use_vga_switcheroo is true.
For more information on device links please refer to:
https://www.kernel.org/doc/html/latest/driver-api/device_link.html
Documentation/driver-api/device_link.rst
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/51bd38360ff502a8c42b1ebf4405ee1d3f27118d.1520068884.git.lukas@wunner.de
If DRM drivers use runtime PM, they currently notify vga_switcheroo
whenever they ->runtime_suspend or ->runtime_resume to update
vga_switcheroo's internal power state tracking.
That's essentially a duplication of a functionality performed by the
PM core as it already tracks the GPU's power state and vga_switcheroo
can always query it.
Introduce a new internal helper vga_switcheroo_pwr_state() which does
just that if runtime PM is used, or falls back to vga_switcheroo's
internal power state tracking if manual power control is used.
Drop a redundant power state check in set_audio_state() while at it.
This removes one of the two purposes of the notification mechanism
implemented by vga_switcheroo_set_dynamic_switch(). The other one is
power management of the audio device and we'll remove that next.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/0aa49d735b988aa04524a8dc339582ace33f0f94.1520068884.git.lukas@wunner.de
When cutting power to a GPU and its integrated HDA controller, their
cached current_state should be updated to D3cold to reflect reality.
We currently rely on the DRM and HDA drivers to do that, however:
- The HDA driver updates the current_state in azx_vs_set_state(), which
will no longer be called with driver power control once we migrate to
device links. (It will still be called with manual power control.)
- If the HDA device is not bound, its current_state remains at D0 even
though the GPU driver may decide to go to D3cold.
- The DRM drivers update the current_state using pci_set_power_state()
which can't put the device into a deeper power state than D3hot if the
GPU is not deemed power-manageable by the platform (even though it
*is* power-manageable by some nonstandard means, such as a _DSM).
Centralize updating the current_state of the GPU and HDA controller in
vga_switcheroo's ->runtime_suspend hook to overcome these deficiencies.
The GPU and HDA controller are two functions of the same PCI device
(VGA class device on function 0 and audio device on function 1) and
no other PCI devices reside on the same bus since this is a PCIe
point-to-point link, so we can just walk the bus and update the
current_state of all devices.
On ->runtime_resume, the HDA controller is in D0uninitialized state.
Resume to D0active and then let it autosuspend as it sees fit.
Note that vga_switcheroo_init_domain_pm_ops() is not supposed to be
called by hybrid graphics laptops which power down the GPU via its root
port's _PR3 resources and consequently vga_switcheroo_runtime_suspend()
is not used. On those laptops, the root port is power-manageable by the
platform (instead of by a nonstandard means) and the current_state is
therefore updated by the PCI core through the following call chain:
pci_set_power_state()
__pci_complete_power_transition()
pci_bus_set_current_state()
Resuming to D0active happens through:
pci_set_power_state()
__pci_start_power_transition()
pci_wakeup_bus()
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/8416958482c8c42d6f311ea5c1e5a65ccf21f5db.1520068884.git.lukas@wunner.de
So far we are using frontbuffer tracking for everything
and ignoring that PSR has a HW capable HW tracking for many
modern usages of GPU on Core platforms and newer Atom ones.
One reason for that is that we were trying to keep same
infrastructure in place for VLV/CHV than the rest of platforms.
But also because when this infrastructure was created
the front-buffer-tracking origin wasn't that good and stable
how it is today after Paulo reworked it to attend FBC cases.
However this PSR implementation without HW tracking died
on gen8LP. And newer platforms are starting to demand more HW
tracking specially with PSR2 cases in mind.
By disabling and re-enabling PSR totally every time we believe
someone is going to change the front buffer content we don't
allow PSR HW tracking to do this job and specially compromising
the whole idea of PSR2 case where the HW tracking detect only
the damaged area and do a partial screen update.
So, from now on, on the platforms that has hw_tracking let's
rely more on HW tracking.
This also is the case in used by other drivers and more validated
by SV teams. So I hope that this will lead us to less misterious
bugs.
v2: Only do this for platform that actually has hw tracking.
v3 from DK
Do this only for flips, small gradual changes are better.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307033420.3086-3-dhinakaran.pandiyan@intel.com
DRM_IOCTL_MODE_CURSOR results in frontbuffer flush before the cursor
plane MMIOs are written to. But this flush should not be necessary for
PSR as hardware tracking triggers PSR exit when MMIOs are written. As
for FBC, the spec says "Flips or changes to plane size and panning" cause
FBC to be nuked. Use origin == ORIGIN_FLIP so that features can ignore
cursor updates in their frontbuffer_flush implementations.
/sys/kernel/debug/dri/0/i915_fbc_status shows
"Compressing: yes" when I move the cursor around.
v3: Use ORIGIN_FLIP now that pin_to_display does not flush frontbuffer.
v2: Update comment in i915_gem_object_pin_to_display_plane. (Chris)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307033420.3086-2-dhinakaran.pandiyan@intel.com
This patch adds support for DMT display modes over HDMI.
The modes timings configurations are from the Amlogic Vendor linux tree
and tested over multiples monitors.
Previously only a selected number of CEA modes were supported.
Only these following modes are supported with these changes:
- 640x480@60Hz
- 800x600@60Hz
- 1024x768@60Hz
- 1152x864@75Hz
- 1280x1024@60Hz
- 1600x1200@60Hz
- 1920x1080@60Hz
The associated code to handle the clock rates is also added.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520935670-14187-1-git-send-email-narmstrong@baylibre.com
WA 0884:bxt:all,cnl:*:A - "When FBC is enabled with eDP PSR,
the CPU host modify writes may not get updated on the Display
as expected.
WA: Write 0x00000000 to CUR_SURFLIVE_A with every CPU
host modify write to trigger PSR exit."
We can also find on spec other cases where they describe
bogus writes to cursor registers to force PSR exit with
HW tracking. And it was confirmed by HW engineers that
this Wa can be safely applied for any frontbuffer activity.
So let's use this more and more here instead of forcibly
disable and re-enable PSR everytime that we have a simple
reliable flush case.
Other commits improve the fbcon/fbdev use a lot, but this
approach is the only when where we can get a fully reliable
console with no slowness or missed frames and PSR still
enabled and active.
v2: - Rebase on drm-tip
- (DK) Add a comment to explain that WA
tells about writing 0 to CUR_SURFLIVE_A but we write to
CUR_SURFLIVE(pipe).
v3: Wa doesn't work on PSR2.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309005218.26772-1-rodrigo.vivi@intel.com
Currently, we only allow ourselves to prune the fences so long as
all the waits completed (i.e. all the fences we checked were signaled),
and that the reservation snapshot did not change across the wait.
However, if we only waited for a subset of the reservation object, i.e.
just waiting for the last writer to complete as opposed to all readers
as well, then we would erroneously conclude we could prune the fences as
indeed although all of our waits were successful, they did not represent
the totality of the reservation object.
v2: We only need to check the shared fences due to construction (i.e.
all of the shared fences will be later than the exclusive fence, if
any).
Fixes: e54ca97747 ("drm/i915: Remove completed fences after a wait")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307171303.29466-1-chris@chris-wilson.co.uk
(cherry picked from commit fa73055b84)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently, BXT_PP is hardcoded with value '0'.
It practically disabled eDP backlight on MRB (BXT) platform.
This patch will tell which BXT_PP registers (there are two set of
PP_CONTROL in the spec) to be used as defined in VBT (Video Bios Timing
table) and this will enabled eDP backlight controller on MRB (BXT)
platform.
v2:
- Remove unnecessary information in commit message.
- Assign vbt.backlight.controller to a backlight_controller variable and
return the variable value.
v3:
- Rebased to latest code base.
- updated commit title.
Signed-off-by: Mustamin B Mustaffa <mustamin.b.mustaffa@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227030734.37901-1-mustamin.b.mustaffa@intel.com
(cherry picked from commit 73c0fcac97)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
