To avoid configuration override, timestamp set call will
be moved from the netdevice open flow to the init flow.
By this, a close-open procedure will not override the timestamp
configuration.
In addition, the change will rename mlx5e_timestamp_set function
to be mlx5e_timestamp_init.
Fixes: ef9814deaf ("net/mlx5e: Add HW timestamping (TS) support")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PPS event did not update ptp_clock_event fields, therefore,
timestamp value was not updated correctly. This fix updates the
event source and the timestamp value for each PPS event.
Fixes: 7c39afb394 ("net/mlx5: PTP code migration to driver core section")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set features function sets dev->features in order to keep track of which
features were successfully changed and which weren't (in case the user
asks for more than one change in a single command).
This breaks the logic in __netdev_update_features which assumes that
dev->features is not changed on success and checks for diffs between
features and dev->features (diffs that might not exist at this point
because of the driver override).
The solution is to keep track of successful/failed feature changes and
assign them to dev->features in case of failure only.
Fixes: 0e405443e8 ("net/mlx5e: Improve set features ndo resiliency")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Should not do the following swap between TCs 0 and 1
when max num of TCs is 1:
tclass[prio=0]=1, tclass[prio=1]=0, tclass[prio=i]=i (for i>1)
Fixes: 08fb1dacdd ("net/mlx5e: Support DCBNL IEEE ETS")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
ethtool statistics should be updated even when the interface is down
since it shows more than just netdev counters, which might change while
the logical link is down.
One useful use case, for example, is when running RoCE traffic over the
interface (while the logical link is down, but physical link is up) and
examining rx_prioX_bytes.
Fixes: f62b8bb8f2 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We didn't store the result of mlx5_init_once, due to that
mlx5_load_one returned success on error. Fix that.
Fixes: 59211bd3b6 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change mlx5_get_uars_page to return ERR_PTR in case of
allocation failure. Change all callers accordingly to
check the IS_ERR(ptr) instead of NULL.
Fixes: 59211bd3b6 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix a memory leak where in case that pci_alloc_irq_vectors failed,
priv->irq_info was not released.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There are systems platform information management interfaces (such as
HOST2BMC) for which we cannot disable local loopback multicast traffic.
Separate disable_local_lb_mc and disable_local_lb_uc capability bits so
driver will not disable multicast loopback traffic if not supported.
(It is expected that Firmware will not set disable_local_lb_mc if
HOST2BMC is running for example.)
Function mlx5_nic_vport_update_local_lb will do best effort to
disable/enable UC/MC loopback traffic and return success only in case it
succeeded to changed all allowed by Firmware.
Adapt mlx5_ib and mlx5e to support the new cap bits.
Fixes: 2c43c5a036 ("net/mlx5e: Enable local loopback in loopback selftest")
Fixes: c85023e153 ("IB/mlx5: Add raw ethernet local loopback support")
Fixes: bded747bb4 ("net/mlx5: Add raw ethernet local loopback firmware command")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
b43_radio_2057_init_post is not called in an interrupt handler
nor holding a spinlock.
The function mdelay in it can be replaced with usleep_range,
to reduce busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dma_zalloc_coherent for allocating zeroed
memory and remove unnecessary memset function.
Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-01-11
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various BPF related improvements and fixes to nfp driver: i) do
not register XDP RXQ structure to control queues, ii) round up
program stack size to word size for nfp, iii) restrict MTU changes
when BPF offload is active, iv) add more fully featured relocation
support to JIT, v) add support for signed compare instructions to
the nfp JIT, vi) export and reuse verfier log routine for nfp, and
many more, from Jakub, Quentin and Nic.
2) Fix a syzkaller reported GPF in BPF's copy_verifier_state() when
we hit kmalloc failure path, from Alexei.
3) Add two follow-up fixes for the recent XDP RXQ series: i) kvzalloc()
allocated memory was only kfree()'ed, and ii) fix a memory leak where
RX queue was not freed in netif_free_rx_queues(), from Jakub.
4) Add a sample for transferring XDP meta data into the skb, here it
is used for setting skb->mark with the buffer from XDP, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENODEV from the of_phy_connect() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I ran into a randconfig build failure:
drivers/net/ethernet/socionext/netsec.c: In function 'netsec_probe':
drivers/net/ethernet/socionext/netsec.c:1583:17: error: implicit declaration of function 'devm_ioremap'; did you mean 'ioremap'? [-Werror=implicit-function-declaration]
Including linux/io.h directly fixes this.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename functions to brcmf_sdio_skbuff_{read,write}() as we pass an
skbuff to this function.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_sdio_buscore_read() there is some special handling upon
register access to chipid register of the chipcommon core. Add
comment explaining why it is done here.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-01-10
This series contains updates to i40e and i40evf only.
Alice adds the displaying of priority xon/xoff packet stats, since we
were already keeping track of them. Based on the recent changes, bump
the driver versions.
Jake changes how the driver determines whether or not the device is
currently up to resolve the possible issue of freeing data structures
and other memory before they have been fully allocated. Refactored
the driver to simplify the locking behavior and to consistently use
spinlocks instead of an overloaded bit lock to protect MAC and filter
lists. Created a helper function which can convert the AdminQ link
speed definition into a virtchnl definition.
Colin Ian King cleans up a redundant variable initialization.
Alex cleans up the driver to stop clearing the pending bit array for
each vector manually, since it is prone to dropping an interrupt and
based on the hardware specs, the pending bit array will be cleared
automatically in MSI-X mode. Cleaned up flags for promiscuous mode to
resolve an issue where enabling & disabling promiscuous mode on a VF
would leave us in a high polling rate for the adminq task. Cleaned up
code that was prone to race issues.
Jingjing renames pipeline personalization profile (ppp) to dynamic
device personalization (ddp) because it was being confused with the
well known point to point protocol. Also removed checks for "track_id"
being zero, since it is valid for it to be zero for profiles that do
not have any 'write' commands.
v2: cleaned up commit message for patch 12 based on feedback from Sergei
Shtylyov and Alex Duyck
v3: dropped patch 15 from the original series while Mariusz Stachura
works on the changes that Jakub Kicinski has suggested
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Initiating a kdump via the command line can cause a pending interrupt
to be handled by the ibmvnic driver when initializing the sub-CRQ
irqs during driver initialization.
NIP [d000000000ca34f0] ibmvnic_interrupt_rx+0x40/0xd0 [ibmvnic]
LR [c000000008132ef0] __handle_irq_event_percpu+0xa0/0x2f0
Call Trace:
[c000000047fcfde0] [c000000008132ef0] __handle_irq_event_percpu+0xa0/0x2f0
[c000000047fcfea0] [c00000000813317c] handle_irq_event_percpu+0x3c/0x90
[c000000047fcfee0] [c00000000813323c] handle_irq_event+0x6c/0xd0
[c000000047fcff10] [c0000000081385e0] handle_fasteoi_irq+0xf0/0x250
[c000000047fcff40] [c0000000081320a0] generic_handle_irq+0x50/0x80
[c000000047fcff60] [c000000008014984] __do_irq+0x84/0x1d0
[c000000047fcff90] [c000000008027564] call_do_irq+0x14/0x24
[c00000003c92af00] [c000000008014b70] do_IRQ+0xa0/0x120
[c00000003c92af50] [c000000008002594] hardware_interrupt_common+0x114/0x180
Signed-off-by: David S. Miller <davem@davemloft.net>
Third batch of updates for v4.16
* Small cleanups in the new rate-scaling code;
* Some improvements in debugging;
* New FW API changes;
* Fix a bug where we got a false-positive warning;
* Fix forced quota debugfs functionality;
ath.git patches for 4.16. Major changes:
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
add changes to t4_eth_xmit to enable vxlan segmentation
offload support.
Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_udp_tunnel_add and ndo_udp_tunnel_del
to support vxlan tunnelling.
Original work by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store and handle ethtool link mode masks within the driver instead of
just a single u32. However, quite a significant amount of existing code
wants to manipulate the masks directly, and thus now uses the first
unsigned long (i.e. mask[0]) as though it were a legacy u32 mask. This
is ok because all the bits that code is interested in are in the first
32 bits of the mask; but it might be a good idea to change them in
future to use the proper bitmap API.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only handles direct speed setting, not autoneg, because the driver is
still trying to pretend it uses the legacy ethtool API which doesn't
have advertised/supported bits for 25/50/100G.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a qdisc is being replaced by another qdisc of the same type, it can
simply override over its configuration.
However, if it replaces a qdisc of another type, it needs to be removed
before setting the new qdisc.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a generic qdisc replace function.
For that goal, add three functions to the qdisc ops struct:
* check_params: Checks if the given parameters are offloadable.
* replace: Offload the given parameters.
* clean_stats: clean the qdisc stats for the offloaded qdisc.
integrate RED offloading into using the new internal replace API.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a destroy function to the qdiscs ops struct.
Create a generic qdisc destroy function, that clears the qdisc metadata as
well as calling the specific qdisc destroy function.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qdisc struct have the Qdisc_class_ops struct.
This patch introduces the similar ops struct for the mlxsw_sp_qdisc_ops
struct. It allows better readability as well as code reusability for the
common parts of some functions like destroy.
The first operations to be added are the statistics getters.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every qdisc op gets the qdisc handle ID as well as its location. Each one
of them, beside replace, checks if the handle doesn't match the qdisc in
the given location, and if so, it returns without running the actual op.
Unite these checks to one comparison function and avoid sending the handle
id to these ops.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tclass number is needed for most of the operations related to the qdisc in
the driver. Create a field for it in the mlxsw_sp_qdisc instead of passing
it to every function as parameter.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve readability by changing the clean stats function to handle only
RED. Qdiscs that will be offloaded in the future will have a clean stats
function of their own.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean RED offloaded stats and make them more generic by breaking the
generic qdisc stats to a struct of their own.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the value of the xstats requested from the driver for offloaded RED
to be incremental, like the normal stats.
It increases consistency - if a qdisc stops being offloaded its xstats
don't change.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of the stats struct to be generic, so it could be used for
other qdisc offload, that will be added in the next patches.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the qdisc related data from the spectrum.h to spectrum_qdisc.c.
Create an init and fini functions for the qdiscs.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve the sparse warning:
"sparse: Variable length array is used."
Use 2 arrays for 2 PRM register accesses.
Fixes: 96f17e0776 ("mlxsw: spectrum: Support RED qdisc offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After performing reset driver polls on HW indication until learning
that the reset is done, but immediately after reset the device becomes
unresponsive which might lead to completion timeout on the first read.
Wait for 100ms before starting the polling.
Fixes: 233fa44bd6 ("mlxsw: pci: Implement reset done check")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the xdp_rxq_info_reg() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 0ddf543226 ("xdp/mlx5: setup xdp_rxq_info")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'd come in with SGE_FL_BUFFER_SIZE[0] and [1] both equal to 64KB and
the extant logic would flag that as an error. This was already fixed in
cxgb4 driver with "92ddcc7 cxgb4: Fix some small bugs in
t4_sge_init_soft() when our Page Size is 64KB".
Original Work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link state and exception interrupts may be masked when we probe.
The firmware should in theory prevent sending (and automasking) those
interrupts if the device is disabled, but if my reading of the FW code
is correct there are firmwares out there with race conditions in this
area. The interrupt may also be masked if previous driver which used
the device was malfunctioning and we didn't load the FW (there is no
other good way to comprehensively reset the PF).
Note that FW unmasks the data interrupts by itself when vNIC is
enabled, such helpful operation is not performed for LSC/EXN interrupts.
Always unmask the auxiliary interrupts after request_irq(). On the
remove path add missing PCI write flush before free_irq().
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP name was going to be confusing since PPP already means point
to point protocol. It is decided to change pipeline personalization
profile(ppp) to dynamic device personalization(ddp).
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Having the interrupts firing while we are polling causes extra overhead and
isn't needed for most systems out there. If an interrupt is lost us
experiencing a 2s latency spike before recovering is still not acceptable
and masks the issue. We are better off just identifying systems that lose
interrupts and instead enable workarounds for those systems.
To that end I am dropping the code that was strobing the interrupts as
there is a narrow window where having them enabled can actually cause
race issues anyway where a few stray packets might get misses if the
interrupt is re-enabled and fires before we call napi_complete.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
