Internal functions for registers and HW access were not prefixed.
This introduce noise in global kernel symbols. Here we add explicit prefix
'hw_atl' to all the HW access layer functions.
Alignment and styling were fixed as well.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original driver code had internal registers and masks declarations
in low case and without any prefix.
Here we make all these uppercase and add already used HW_ATL prefix
to recognize these.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aq_nic_s was hidden in aq_nic_internal.h, that made it difficult to access
nic fields and structures from other modules.
This change moves aq_nic_s struct into aq_nic.h and thus makes it available
to other driver modules, mainly pci module and hw related module.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate useless passing of net_device_ops and ethtools_ops through
deep chain of calls.
Move all pci related code into aq_pci_func module.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware operations and capabilities tables are constants and
never changed. Declare these as constants.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use direct aq_hw_s *self reference where possible
Eliminate useless abstraction PHAL, duplicated structures definitions,
Simplify nic config structure creation and management.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of aq_obj_s structure is noop, here we remove it
replacing access to flags filed directly.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds timestamping support for both receive and transmit
paths. On the receive side no filters are supported i.e either
all pkts will get a timestamp appended infront of the packet or none.
On the transmit side HW doesn't support timestamp insertion but
only generates a separate CQE with transmitted packet's timestamp.
Also HW supports only one packet at a time for timestamping on the
transmit side.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Precision Time Protocol
Clocks and Timestamping hardware found on Cavium ThunderX
processors.
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
More fixes:
* hwsim:
- properly flush deletion works at module unload
- validate # of channels passed from userspace
* cfg80211:
- fix RCU locking regression
- initialize on-stack channel data for nl80211 event
- check dev_set_name() return value
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/mellanox/mlxsw/spectrum_qdisc.c:464:1: warning:
symbol 'mlxsw_sp_qdisc_prio_unoffload' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For legacy chips without CLM blob files, kernel with user helper function
returns -EAGAIN when we request_firmware(), and then driver got failed
when bringing up legacy chips. We expect the CLM blob file for legacy chip
is not existence in firmware path, but the -ENOENT error is transferred to
-EAGAIN in firmware_class.c with user helper.
Because of that, we continue with CLM data currently present in firmware
if getting error from doing request_firmware().
Cc: stable@vger.kernel.org # v4.15.y
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for hot reload. First, all the driver/core resources are
released but the PCI and devlink instances, then reset is performed
through the PCI interface. Finally the driver performs initialization.
In case of reload failure the driver is left in a partially initialized
state. Special care is taken during the driver removal in order to
properly handle this state.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the KVD partition was static. This patch introduces the
ability to get the resource sizes via devlink. In case the resource is not
available the default configuration is used.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for getting the kvdl occupancy through the resource interface.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Connect current dpipe tables to resources. The tables are connected
in the following fashion:
1. IPv4 host -> KVD hash single
2. IPv6 host -> KVD hash double
3. Adjacency -> KVD linear
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register the KVD resources with devlink. The KVD is a memory resource
which is subdivided into three partitions which are the linear, hash
single and hash double.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation stage before introducing hot reload. During the
reload process the ASIC should be resetted by accessing the PCI BAR due
to unavailability of the mailbox/emad interfaces.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new helpers for paged register access.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helpers phy_set_bits / phy_clear_bits in phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to architecture limitations, the IBM VNIC client driver is unable
to perform MAC address changes unless the device has "logged in" to
its backing device. Currently, pending MAC changes are handled before
login, resulting in an error and failure to change the MAC address.
Moving that chunk to the end of the ibmvnic_login function, when we are
sure that it was successful, fixes that.
The MAC address can be changed when the device is up or down, so
only check if the device is in a "PROBED" state before setting the
MAC address.
Fixes: c26eba03e4 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify()
usage with device_lock()") resolves races between driver reset and
removal, but it introduces some new deadlock problems. If we see a
timeout while we've already started suspending, removing, or shutting
down the driver, we might see:
(a) a worker thread, running mwifiex_pcie_work() ->
mwifiex_pcie_card_reset_work() -> pci_reset_function()
(b) a removal thread, running mwifiex_pcie_remove() ->
mwifiex_free_adapter() -> mwifiex_unregister() ->
mwifiex_cleanup_pcie() -> cancel_work_sync(&card->work)
Unfortunately, mwifiex_pcie_remove() already holds the device lock that
pci_reset_function() is now requesting, and so we see a deadlock.
It's necessary to cancel and synchronize our outstanding work before
tearing down the driver, so we can't have this work wait indefinitely
for the lock.
It's reasonable to only "try" to reset here, since this will mostly
happen for cases where it's already difficult to reset the firmware
anyway (e.g., while we're suspending or powering off the system). And if
reset *really* needs to happen, we can always try again later.
Fixes: b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()")
Cc: <stable@vger.kernel.org>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit b713bbf147.
The "fix" in question does not actually fix all related problems, and it
also introduces new deadlock possibilities. Since commit b014e96d1a
("PCI: Protect pci_error_handlers->reset_notify() usage with
device_lock()"), the race in question is actually resolved (PCIe reset
cannot happen at the same time as remove()). Instead, this "fix" just
introduces a deadlock where mwifiex_pcie_card_reset_work() is waiting on
device_lock, which is held by PCIe device remove(), which is waiting
on...mwifiex_pcie_card_reset_work().
The proper thing to do is just to fix the deadlock. Patch for this will
come separately.
Cc: Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable fw_ps_state is assigned a value but it is never read, hence
it is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:736:2:
warning: Value stored to 'fw_ps_state' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add an expansion slot attribute to allow drivers to properly handle
cards like Comm Slot cards and PDS cards without declaration ROMs.
This clarifies the logic for the Centris 610 model which has no
Comm Slot but has an optional on-board SONIC device.
Cc: "David S. Miller" <davem@davemloft.net>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
It is misleading to call a functional resource a "device". In adopting
the Linux Driver Model, the struct device will be embedded in struct
nubus_board. That will compound the terminlogy problem because drivers
will bind with boards, not with functional resources. Avoid this by
renaming struct nubus_dev as struct nubus_rsrc. "Functional resource"
is the vendor's terminology so this helps avoid confusion.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Checkpatch found these issues:
drivers/net/wireless/ath/ath10k/ce.h:324: Please use a blank line after function/struct/union/enum declarations
drivers/net/wireless/ath/ath10k/core.c:1321: Please don't use multiple blank lines
drivers/net/wireless/ath/ath10k/htt.h:1859: Please use a blank line after function/struct/union/enum declarations
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable section_table.size is a u32 and so cannot be less than
zero, hence the less than zero check is redundant and can be
removed.
Detected by CoverityScan, CID#1463855 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some rare conditions when running one PEAK USB-FD interface over
a non high-speed USB controller, one useless USB fragment might be sent.
This patch fixes the way a USB command is fragmented when its length is
greater than 64 bytes and when the underlying USB controller is not a
high-speed one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Validate ie_len after the alignment padding before access the buffer
to avoid potential overflow.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some platform(BIOS) blocks legacy interrupts (INTx), and only allows MSI
for WLAN device. So adding a quirk to list those machines and set
use_msi automatically.
Adding the following platforms to the quirk.
Dell Inspiron 24-3460
Dell Inspiron 3472
Dell Inspiron 14-3473
Dell Vostro 3262
Dell Vostro 15-3572
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On new Intel platforms like ApolloLake, legacy interrupt mechanism
(INTx) is not supported, so WLAN modules are not working because
interrupts are missing, therefore this patch is to add MSI support to
ath9k. With module paremeter "use_msi=1", ath9k driver would try to
use MSI instead of INTx.
Signed-off-by: Russell Hu <rhu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add call to new generic functions that provides support via a binding
to limit the arbitration rate and/or data rate imposed by the physical
transceiver connected to the MCAN peripheral.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for CONFIG_PM which is the new way to handle managing clocks.
Move the clock management to pm_runtime_resume() and pm_runtime_suspend()
callbacks for the driver.
CONFIG_PM is required by OMAP based devices to handle clock management.
Therefore, this allows future Texas Instruments SoCs that have the MCAN IP
to work with this driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As the previous patch removed alloc_m_can_dev(), let's get rid of the
corresponding free_m_can_dev() and call free_candev() directly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With the version no longer required to allocate the net device, it can
be moved to probe and the alloc_m_can_dev() function can be simplified.
Therefore, move the allocation of net device to probe and change
alloc_m_can_dev() to setup_m_can_dev().
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently the m_can version is used to set the tx_fifo_count to 1 when
allocating the net device. However, this is redundant as a value of 1
for the tx_fifo_count needs to be provided in the bosch,mram-cfg
property of the device tree node anyway.
Therefore, remove check for version when allocating the net device.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During test transmitting using CAN-FD at high bitrates (> 2 Mbps)
would fail. Scoping the signals I noticed that only a single bit
was being transmitted and with a bit more investigation realized the
actual MCAN IP would go back to initialization mode automatically.
It appears this issue is due to the MCAN needing to use the Transmitter
Delay Compensation Mode with the correct value for the transmitter delay
compensation offset (tdco). What impacts the tdco value isn't 100% clear
but to calculate it you use an equation defined in the MCAN User's Guide.
The user guide mentions that this register needs to be set based on clock
values, secondary sample point and the data bitrate. One of the key
variables that can't automatically be determined is the secondary
sample point (ssp). This ssp is similar to the sp but is specific to this
transmitter delay compensation mode. The guidelines for configuring
ssp is rather vague but via some CAN test it appears for DRA76x that
putting the value same as data sampling point works.
The CAN-CIA's "Bit Time Requirements for CAN FD" paper presented at
the International CAN Conference 2013 indicates that this TDC mode is
only needed for data bit rates above 2.5 Mbps. Therefore, only enable
this mode when the data bit rate is above 2.5 Mbps.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Various CAN or CAN-FD IP may be able to run at a faster rate than
what the transceiver the CAN node is connected to. This can lead to
unexpected errors. However, CAN transceivers typically have fixed
limitations and provide no means to discover these limitations at
runtime. Therefore, add support for a can-transceiver node that
can be reused by other CAN peripheral drivers to determine for both
CAN and CAN-FD what the max bitrate that can be used. If the user
tries to configure CAN to pass these maximum bitrates it will throw
an error.
Also add support for reading bitrate_max via the netlink interface.
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[nsekhar@ti.com: fix build error with !CONFIG_OF]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Allocating steerable UD QPs depends on having at least one IB port,
while releasing those QPs does not.
As a result, when there are only ETH ports, the IB (RoCE) driver
requests releasing a qp range whose base qp is zero, with
qp count zero.
When SR-IOV is enabled, and the VF driver is running on a VM over
a hypervisor which treats such qp release calls as errors
(rather than NOPs), we see lines in the VM message log like:
mlx4_core 0002:00:02.0: Failed to release qp range base:0 cnt:0
Fix this by adding a check for a zero count in mlx4_release_qp_range()
(which thus treats releasing 0 qps as a nop), and eliminating the
check for device managed flow steering when releasing steerable UD QPs.
(Freeing ib_uc_qpns_bitmap unconditionally is also OK, since it
remains NULL when steerable UD QPs are not allocated).
Cc: <stable@vger.kernel.org>
Fixes: 4196670be7 ("IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-12-01,Re: pull-request: can-next
this is a pull request of 7 patches for net-next/master.
All patches are by me. Patch 6 is for the "can_raw" protocol and add
error checking to the bind() function. All other patches clean up the
coding style and remove unused parameters in various CAN drivers and
infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The dual-port Ether configurations always have a shared TSU to e.g. pass
the packets between those ports. With the TSU init. code gathered under
the single *if*, we now can only get the port # from 'platform_device::id'
only when we actually need it (and not recalculate it each time)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth_cpu_data::chip_reset() method always resets using ARSTR and
this register is always located at the start of the TSU register region.
Therefore, we can only call this method if we know TSU is there and thus
simplify the probing code a bit...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARSTR is always located at the start of the TSU register region, thus
using add_reg() instead of add_tsu_reg() in __sh_eth_get_regs() to dump it
causes EDMR or EDSR (depending on the register layout) to be dumped instead
of ARSTR. Use the correct condition/macro there...
Fixes: 6b4b4fead3 ("sh_eth: Implement ethtool register dump operations")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
