Account for operational state when determining port linkup state,
as per Documentation/networking/operstates.txt.
Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for specifying system controller that configures
phy-mode setting.
According to the DT property "phy-mode", it's necessary to configure the
controller, which is used to choose the settings of the MAC suitable,
for example, mdio pin connections, internal clocks, and so on.
Supported phy-modes are SoC-dependent. The driver allows phy-mode to set
"internal" if the SoC has a built-in PHY, and {"mii", "rmii", "rgmii"}
if the SoC supports each mode. So we have to check whether the phy-mode
is valid or not.
This adds the following features for each SoC:
- check whether the SoC supports the specified phy-mode
- configure the controller accroding to phy-mode
The DT property accepts one argument to distinguish them for multiple MAC
instances.
ethernet@65000000 {
...
socionext,syscon-phy-mode = <&soc_glue 0>;
};
ethernet@65200000 {
...
socionext,syscon-phy-mode = <&soc_glue 1>;
};
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link is becoming up for Pro4 SoC, the kernel is stalled
due to some missing clocks and resets.
The AVE block for Pro4 is connected to the GIO bus in the SoC.
Without its clock/reset, the access to the AVE register makes the
system stall.
In the same way, another MAC clock for Giga-bit Connection and
the PHY clock are also required for Pro4 to activate the Giga-bit feature
and to recognize the PHY.
To satisfy these requirements, this patch adds support for multiple clocks
and resets, and adds the clock-names and reset-names to the binding because
we need to distinguish clock/reset for the AVE main block and the others.
Also, make the resets a required property. Currently, "reset is
optional" relies on that the bootloader or firmware has deasserted
the reset before booting the kernel. Drivers should work without
such expectation.
Fixes: 4c270b55a5 ("net: ethernet: socionext: add AVE ethernet driver")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register will search for any mdiobus board info registered for
the bus being registered. If found, it will probe devices on the bus.
That device, if for example it is an ethernet switch, may then try to
register an mdio bus. Thus we need to allow recursive calls to
mdiobus_register.
Holding the mdio_board_lock will cause a deadlock during this
recursion. Release the lock and use list_for_each_entry_safe.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to open aggregations on 22000 HW before
traffic had actually passed, the driver will discover
it is missing a queue to aggregate on. In such a case -
allocate a queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's already an opmode common file for nvm iwl-nvm-parse.c
Move the content of fw/nvm.c to iwl-nvm-parse.c and delete fw/nvm.c.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The sku_capa_band_24GHz_enable and sku_capa_band_52GHz_enable symbols
cause checkpatch to complain whenever we use them. To prevent this,
convert them to all lower case.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of having a boolean for each modifier we need to handle in the
channel maps, create a bitmask with flags that denote each
modification.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update rs-fw API to match changes in FW. Specifically, the
TLC_MNG_NOTIF_REQ_CMD command and TLC_MNG_AMSDU_ENABLE_NOTIF
notification are removed, the A-MSDU related info is received from FW
via the TLC_MNG_UPDATE_NOTIF, and the TLC_MNG_CONFIG_CMD uses version
2 of its data structure.
Additionally, constify some arguments in a couple of functions.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22000 devices rely on this flag to install the key to the right
queues. For earlier devices we didn't have a key / queue mapping and
the key was sent along with the Tx command for each Tx hence the
problem didn't arise.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid a race where two (or more) commands get the
same index:
1. T1 calls enqueue_hcmd and the local TFD index is assigned to
txq->write_ptr;
2. Context switch 'before incrementing txq->write_ptr';
3. T2 calls enqueue_hcmd and the local TFD index is assigned to
txq->write_ptr;
4. Now the index is set to the same value for both commands of T1 and
T2.
To prevent this from happening, set the local TFD index inside the
critical section (the index is set by global txq write pointer).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move all the NVM file handling code to iwl-nvm-parse.c where all this
stuff belongs. This cleans up the MVM specific code and allows easier
reuse by other opmodes if needed.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22000 devices, aka gen2, the TFS is 256 bytes.
In order to save memory, use shorter TX queue for aux and
mgmt queues, since there isn't much traffic on them.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Op mode will begin tp use varying size of TX queue.
All the infra is in place, allow it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for dynamic queue sizing, add a parameter
of the TX queue size to the dynamic queue allocation op
mode API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit dd05f9aab4.
Shorter TX queues support was added eventually without the
need for the parameters this patch added.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When support for shorter TX queues was introduced, it
didn't include the actual allocation of shorter queue,
which is the main motive for the change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These functions are not debugfs functions so they should be in dbg.h
instad in debugfs.h.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we enable TSO, we can have a lot of packets in the
operation mode that will be pushed to the transport
no matter what is the queue's fullness state.
To cope with that the transport can buffer those packets
and add them to the ring later when there is more room.
This implementation was missing in the Gen2 devices'
code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support the new APIs and activate AMSDU based on the
offloaded TLC decisions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code that sets the correct out-of-channel priority depending on
the scan type was accidentally removed during a rebase. Add it back.
Fixes: c1a7515393 ("iwlwifi: mvm: add adaptive dwell support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Introduce and use iwl_mvm_cdb_scan_api(), which checks the family.
Most of this will go away once the 22000 firmware supports adaptive
dwell, after which the V6 scan API won't be used, but the V3 scan
*config* API will still need to be distinguished.
In any case, this gets rid of the completely bogus has_new_tx_api()
checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Detect low latency and traffic load per band. Add support for
deciding on scan type and timings per band.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Try to detect that the AP is not using aggregation even when there's
enough traffic to make it worthwhile; if this is the case and U-APSD
is enabled then assume the AP is broken (like so many) and doesn't
enable aggregation when U-APSD is used. In this case, disconnect from
the AP and blacklist U-APSD for a potential new connection to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The primary channel is the channel that will be untouched by BT. The
secondary channel might be touched by BT. Hence, we want the primary
to be the most active channel. To do so, use the TCM infrastructure.
Since the BT keeps sending notifications, we can rely on them to
trigger the check. Every 10 seconds, we will check what is the most
active context and chose the right primary.
We need to wait 10 seconds before we modify the settings because
frequent changes in these settings can confuse BT.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code for changing the scan priority is already implemented, but
isn't yet in use. Now that TCM data is available, we can base the
scan priority decision on the traffic load.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Traffic condition monitor gathers data about the traffic load and
other conditions and can be used to make decisions regarding latency,
throughput etc. This patch introduces the code and data structures to
collect this data for future use.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver. This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.
Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096. Move the kzalloc() call
into the bnxt_get_pkgver() function.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
offloads is a buffer in virtio format, should use
the __virtio64 tag.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programming vids (adding or removing them) still passes
guest-endian values in the DMA buffer. That's wrong
if guest is big-endian and when virtio 1 is enabled.
Note: this is on top of a previous patch:
virtio_net: split out ctrl buffer
Fixes: 9465a7a6f ("virtio_net: enable v1.0 support")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending control commands, virtio net sets up several buffers for
DMA. The buffers are all part of the net device which means it's
actually allocated by kvmalloc so it's in theory (on extreme memory
pressure) possible to get a vmalloc'ed buffer which on some platforms
means we can't DMA there.
Fix up by moving the DMA buffers into a separate structure.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:
ubuntu@d05-3:~$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
enahisic2i0-tx1
Increase the max ring name length to allow for an interface name
of IFNAMSIZE. After this change, I now see:
$ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
enahisic2i0-tx0
enahisic2i0-tx1
enahisic2i0-tx2
[...]
enahisic2i0-tx8
enahisic2i0-tx9
enahisic2i0-tx10
enahisic2i0-tx11
enahisic2i0-tx12
enahisic2i0-tx13
enahisic2i0-tx14
enahisic2i0-tx15
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add platform device driver to populate the ax88796 platform data from
information provided by the XSurf100 zorro device driver. The ax88796
module will be loaded through this module's probe function.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net device struct pointer is stored as platform device drvdata on
module probe - clear the drvdata entry on probe fail there, as well as
when unloading the module.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Amiga X-Surf100, the network card interrupt is shared with many
other interrupt sources, so requires the IRQF_SHARED flag to register.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to tell the ax88796 driver whether it is sensible to enter
the 8390 interrupt handler, an "is this interrupt caused by the 88796"
callback has been added to the ax_plat_data structure (with NULL being
compatible to the previous behaviour).
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add platform specific hooks for block transfer reads/writes of packet
buffer data, superseding the default provided ax_block_input/output.
Currently used for m68k Amiga XSurf100.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This complements the fix in 82533ad9a1 ("net: ethernet: ax88796:
don't call free_irq without request_irq first") that removed the
free_irq call in the error path of probe, to also not call free_irq
when remove is called to revert the effects of probe.
Fixes: 82533ad9a1 (net: ethernet: ax88796: don't call free_irq without request_irq first)
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call ax_mii_init in ax_open(), and unregister/remove mdiobus resources
in ax_close().
This is needed to be able to unload the module, as the module is busy
while the MII bus is attached.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To read the MAC address from the (virtual) SAprom, the remote DMA
unit needs to be set up like for every other process access to card-local
memory.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Asix Electronics PHY found on the X-Surf 100 Amiga Zorro network
card by Individual Computers is buggy, and needs the reset bit toggled
as workaround to make a PHY soft reset succeed.
Add workaround driver just for this special case.
Suggested in xsurf100 patch series review by Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform data header file is now unused. Remove it, but add
an extra include which it brought in.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the allocation of this structure to the probe function is a
step towards making it the core data structure of the driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the code, removing the need to handle active low
flags, etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
