Add support for adaptive TX moderation. This greatly reduces TX interrupt
rate and increases bandwidth, mostly for TCP bandwidth over ARM
architecture (below). There is a slight single stream TCP with very large
message sizes degradation (x86). In this case if there's any moderation on
transmitted packets the bandwidth would reduce due to hitting TCP output limit.
Since this is a synthetic case, this is still worth doing.
Performance improvement (ConnectX-4Lx 40GbE, ARM)
TCP 64B bandwidth with 1-50 streams increased 6-35%.
TCP 64B bandwidth with 100-500 streams increased 20-70%.
Performance improvement (ConnectX-5 100GbE, x86)
Bandwidth: increased up to 40% (1024B with 10s of streams).
Interrupt rate: reduced up to 50% (1024B with 1000s of streams).
Performance degradation (ConnectX-5 100GbE, x86)
Bandwidth: up to 10% decrease single stream TCP (1MB message size from
51Gb/s to 47Gb/s).
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix in Commit dbe173079a ("bridge: fix netconsole
setup over bridge") is also needed for team driver.
While at it, remove the unnecessary parameter *team from
team_port_enable_netpoll().
v1->v2:
- fix it in a better way, as does bridge.
Fixes: 0fb52a27a0 ("team: cleanup netpoll clode")
Reported-by: João Avelino Bellomo Filho <jbellomo@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HP laptops have only a single wifi antenna. This would not be a
problem except that they were shipped with an incorrectly encoded
EFUSE. It should have been possible to open the computer and transfer
the antenna connection to the other terminal except that such action
might void the warranty, and moving the antenna broke the Windows
driver. The fix was to add a module option that would override the
EFUSE encoding. That was done with commit c18d8f5095 ("rtlwifi:
rtl8723be: Add antenna select module parameter"). There was still a
problem with Bluetooth coexistence, which was addressed with commit
baa1702290 ("rtlwifi: btcoexist: Implement antenna selection").
There were still problems, thus there were commit 0ff78adeef
("rtlwifi: rtl8723be: fix ant_sel code") and commit 6d62269283
("rtlwifi: btcoexist: Fix antenna selection code"). Despite all these
attempts at fixing the problem, the code is not yet right. A proper
fix is important as there are now instances of laptops having
RTL8723DE chips with the same problem.
The module parameter ant_sel is used to control antenna number and path.
At present enum ANT_{X2,X1} is used to define the antenna number, but
this choice is not intuitive, thus change to a new enum ANT_{MAIN,AUX}
to make it more readable. This change showed examples where incorrect
values were used. It was also possible to remove a workaround in
halbtcoutsrc.c.
The experimental results with single antenna connected to specific path
are now as follows:
ant_sel ANT_MAIN(#1) ANT_AUX(#2)
0 -8 -62
1 -62 -10
2 -6 -60
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Fixes: c18d8f5095 ("rtlwifi: rtl8723be: Add antenna select module parameter")
Fixes: baa1702290 ("rtlwifi: btcoexist: Implement antenna selection")
Fixes: 0ff78adeef ("rtlwifi: rtl8723be: fix ant_sel code")
Fixes: 6d62269283 ("rtlwifi: btcoexist: Fix antenna selection code")
Cc: Stable <stable@vger.kernel.org> # 4.7+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When version 8 of the scan command API was introduced, only the size
of version 7 was updated, causing older versions of the firmware to
throw BAD_COMMAND errors.
Calculating the old version based on the size of the latest version
got too complicated and the size of the older versions will never
change anyway, so it's better to just hardcoded the sizes.
Fixes: 66fa2424df ("iwlwifi: fw api: support the new scan request FW API version")
Reported-by: Scott Register <sreg@sreg.io>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iwlwifi patches for 4.18
* implement Traffic Condition Monitor;
* use TCM for scan and BT coex;
* use TCM to detect when the AP doesn't support UAPSD properly;
* some more work for the 22000 family of devices;
* introduce AMSDU rate control offload;
* a couple of clean-ups and bugfixes.
When the wifi driver core passes IE elements in the scan request, append
them to the firmware message. The driver currently tells the core that
it is capable of attaching up to WCN36XX_MAX_SCAN_IE_LEN octets, but
doesn't actually pass them to the the hardware.
Note that this patch doesn't fix a bug that was observed. The change is
merely done for the sake of completeness as the hardware supports
appending IEs in scans. Tests show that network scans work fine with
this patch applied.
Some defines were moved around to avoid cyclic include dependencies.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pass the bss_type of the currently configured BSS in the message for the
scan request. Therefore, that setting needs to be kept in struct
wcn36xx_vif.
This seems to be only interesting when scanning for a specific SSID
and doesn't matter for regular wildcard scans.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For firmwares that don't have the SCAN_OFFLOAD feature bit set, do
not call into wcn36xx_smd_stop_hw_scan(). Instead, stop the asynchronous
work and call into ieee80211_scan_completed() immediately.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the network interface goes down while a scan request is still
pending that can't be stopped due to firmware hickups, wcn->scan_req
remains set, even though the hardware is deinitialized. This results
in -EBUSY for all scan requests after the interface was brought up
again.
Fix this by explicitly completing pending scan requests in
wcn36xx_stop().
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware sends a WCN36XX_HAL_SCAN_IND_DEQUEUED indication,
the request is apparently no longer valid. Attempts to stop the hardware
scan request subsequently will lead to the following error message, and
the hardware is no longer able to communicate with any AP:
[ 57.917186] wcn36xx: ERROR hal_stop_scan_offload response failed err=5
Interpreting this indicator message as scan abortion fixes this.
While at it, add a newline to a debug print.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable sta power save in fw for the targets that
supports idle power save. The idle ps enable command
will be ignored by the firmware which does not support
this feature.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SRRI/DRRI are not mapped in the HW Shadow block and can lead
to un-clocked access if common subsystem in the target is
powered down due to idle mode.
To mitigate this problem SRRI/DRRI can be read from
DDR instead of doing an actual hardware read.
Host allocates non cached memory on ddr and configures
the physical address of this memory to the CE hardware.
The hardware updates the RRI on this particular location.
Read SRRI/DRRI from DDR location instead of
direct target read.
Enable retention restore on ddr using hw params to enable
in specific targets.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 needs shadow register write operation support
for copy engine for regular operation in powersave mode.
Add support for copy engine shadow register write in
datapath tx for WCN3990
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3990 supports shadow register for ce write.
Add a hw param for shadow register support.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default ath10k driver enables the support for HW_CHECKSUM
(NETIF_F_HW_CSUM). Since the TCP/UDP checksum calculation is not enabled
in the wcn3990 firmware the checksum is incorrect in the TCP/UDP packets
and all patckets are dropped. But due note that wcn3990 support in
ath10k is still incomplete so this isn't a critical fix (yet).
Enable hw checksum calculations in wcn3990 hardware by
setting the proper flags in msdu descriptor tso flags.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware message to delete BSS keys expects a BSS index to be passed.
This field is currently hard-coded to 0. Fix this by passing in the index
we received from the firmware when the BSS was configured.
The encryption type in that message also needs to be set to what was used
when the key was set, so the assignment of vif_priv->encrypt_type is now
done after the firmware command was sent. This reportedly fixes the
following error in AP mode:
wcn36xx: ERROR hal_remove_bsskey response failed err=6
Also, AFAIU, when a BSS is deleted, the firmware apparently drops all the
keys associated with it. Trying to remove the key explicitly afterwards
will hence lead to the following message:
wcn36xx: ERROR hal_remove_bsskey response failed err=16
This is now suppressed with an extra check for the BSS index validity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When trying to set wow wakeup patterns it fails with this command:
iw phyxx wowlan enable patterns offset xx+ IP address xx.xx.xx.xx
The reason is that the wow pattern from upper layer is in 802.3 format
for this case, it need to convert it to 802.11 format. The input
offset parameter is used for 802.3, but the actual offset firmware
need depends on rx_decap_mode, so that it needs to be recalculated.
Pattern of 802.3 packet is not same with 802.11 packet. If the
rx_decap_mode is ATH10K_HW_TXRX_NATIVE_WIFI, then firmware will
receive data packet with 802.11 format from hardware.
Tested with QCA6174 hw3.0 with firmware
WLAN.RM.4.4.1-00099-QCARMSWPZ-1, but this will also affect QCA9377.
This has always failed, so it's not a regression with new firmware
releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.
Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already allocated the device and platform data at this
point. Instead of simply return from the probe function we
need to cleanup the resources first.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Xue Liu <liuxuenetmail@gmail.com>
atusb_probe() is never called in atomic context.
This function is only set as ".probe" in struct usb_driver.
Despite never getting called from atomic context,
atusb_probe() calls usb_alloc_urb() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Configuration information is added to the debug data collection, in
addition to register dump.
Added qed_dbg_nvm_image() that receives an image type, allocates a
buffer and reads the image. The images are saved in the buffers and the
dump size is updated.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nvm images attributes are cached during driver load, acquiring ptt
is not needed when calling qed_mcp_get_nvm_image().
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the core version detection to a common place ("hwif.c") and
implement a table which can be used to lookup the correct callbacks for
each IP version.
This simplifies the initialization flow of each IP version and eases
future implementation of new IP versions.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no benefit in using netif_info et al before the net_device has
been registered. We get messages like
r8169 0000:03:00.0 (unnamed net_device) (uninitialized): [message]
Therefore use dev_info/dev_err instead.
As a side effect we don't need parameter dev for function
rtl8169_get_mac_version() any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Commit 8a8efa22f5 ("bonding: sync netpoll code with bridge"), it
would set slave_dev npinfo in slave_enable_netpoll when enslaving a dev
if bond->dev->npinfo was set.
However now slave_dev npinfo is set with bond->dev->npinfo before calling
slave_enable_netpoll. With slave_dev npinfo set, __netpoll_setup called
in slave_enable_netpoll will not call slave dev's .ndo_netpoll_setup().
It causes that the lower dev of this slave dev can't set its npinfo.
One way to reproduce it:
# modprobe bonding
# brctl addbr br0
# brctl addif br0 eth1
# ifconfig bond0 192.168.122.1/24 up
# ifenslave bond0 eth2
# systemctl restart netconsole
# ifenslave bond0 br0
# ifconfig eth2 down
# systemctl restart netconsole
The netpoll won't really work.
This patch is to remove that slave_dev npinfo setting in bond_enslave().
Fixes: 8a8efa22f5 ("bonding: sync netpoll code with bridge")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6870de435b ("bpf: make virtio compatible w/
bpf_xdp_adjust_tail") i didn't account for vi->hdr_len during new
packet's length calculation after bpf_prog_run in receive_mergeable.
because of this all packets, if they were passed to the kernel,
were truncated by 12 bytes.
Fixes:6870de435b90 ("bpf: make virtio compatible w/ bpf_xdp_adjust_tail")
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion of rndis friendly name to utf8 uses a standard
kernel routine which is optional in config. Therefore build
would fail for some configurations. Resolve by selecting needed
library.
Fixes: 0fe554a46a ("hv_netvsc: propogate Hyper-V friendly name into interface alias")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-04-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Initial work on BPF Type Format (BTF) is added, which is a meta
data format which describes the data types of BPF programs / maps.
BTF has its roots from CTF (Compact C-Type format) with a number
of changes to it. First use case is to provide a generic pretty
print capability for BPF maps inspection, later work will also
add BTF to bpftool. pahole support to convert dwarf to BTF will
be upstreamed as well (https://github.com/iamkafai/pahole/tree/btf),
from Martin.
2) Add a new xdp_bpf_adjust_tail() BPF helper for XDP that allows
for changing the data_end pointer. Only shrinking is currently
supported which helps for crafting ICMP control messages. Minor
changes in drivers have been added where needed so they recalc
the packet's length also when data_end was adjusted, from Nikita.
3) Improve bpftool to make it easier to feed hex bytes via cmdline
for map operations, from Quentin.
4) Add support for various missing BPF prog types and attach types
that have been added to kernel recently but neither to bpftool
nor libbpf yet. Doc and bash completion updates have been added
as well for bpftool, from Andrey.
5) Proper fix for avoiding to leak info stored in frame data on page
reuse for the two bpf_xdp_adjust_{head,meta} helpers by disallowing
to move the pointers into struct xdp_frame area, from Jesper.
6) Follow-up compile fix from BTF in order to include stdbool.h in
libbpf, from Björn.
7) Few fixes in BPF sample code, that is, a typo on the netdevice
in a comment and fixup proper dump of XDP action code in the
tracepoint exception, from Wang and Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tun driver, in absence of an eBPF steering program,
always compute the rxhash in its rx path, even when such value
is later unused due to additional checks (
This changeset moves the all the related checks just before the
__skb_get_hash_symmetric(), so that the latter is no more computed
when unneeded.
Also replace an unneeded RCU section with rcu_access_pointer().
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:
0=link/activity 1=link1000/activity
2=link100/activity 3=link10/activity
4=link100/1000/activity 5=link10/1000/activity
6=link10/100/activity 14=off 15=on
These values are given symbolic constants in a dt-bindings header.
Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a standard mechanism for locating and using a MAC address from
the Device Tree. Use this facility in the lan78xx driver to support
applications without programmed EEPROM or OTP. At the same time,
regularise the handling of the different address sources.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpumask_local_spread to provide interrupt affinity hints
for each queue. This will spread interrupts across NUMA local
CPUs first, extending to remote nodes if needed.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be a need for VF driver to request PF to explicitly update its
bulletin with a MAC address.
e.g. When user assigns a MAC address to VF while VF is still down,
and PF's bulletin board contains different MAC address, in this case,
when VF's interface is brought up, it gets loaded with MAC address from
bulletin board which is not desirable.
To handle this corner case, we need a new TLV to request PF to update
its bulletin board with suggested MAC.
This request will be honored only for trusted VFs.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per existing behavior, when PF sets a MAC address for a VF
(also called as forced MAC), VF is not allowed to change its
MAC address afterwards.
This puts the limitation on few use cases such as bonding of VFs,
where bonding driver asks VF to change its MAC address.
This patch uses a VF trust mode to allow VF to change its MAC address
in spite PF has set a forced MAC for that VF.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, on a new link creation or when 'remote' address parameter
is updated, an MTU is not changed and always equals 1500. When a lower
device has a larger MTU, it might not be efficient, e.g. for UDP, and
requires the manual MTU adjustments to match the MTU of the lower
device.
This patch tries to automate this process, finds a lower device using
the 'remote' address parameter, then uses its MTU to tune GENEVE's MTU:
* on a new link creation
* when 'remote' parameter is changed
Also with this patch, the MTU from a user, on a new link creation, is
passed to geneve_change_mtu() where it is verified, and MTU adjustments
with a lower device is skipped in that case. Prior that change, it was
possible to set the invalid MTU values on a new link creation.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_change_mtu() will be used not only as ndo_change_mtu() callback,
but also to verify a user specified MTU on a new link creation in the
next patch.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ETH_HLEN instead and introduce two new macros: GENEVE_IPV4_HLEN
and GENEVE_IPV6_HLEN that include Ethernet header length, corresponded
IP header length and GENEVE_BASE_HLEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
