The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In an RFC patch, Sven Eckelmann and Simon Wunderlich reported:
"QCA 802.11n chips (especially AR9330/AR9340) sometimes end up in a
state in which a read of AR_CFG always returns 0xdeadbeef.
This should not happen when when the power_mode of the device is
ATH9K_PM_AWAKE."
Include the check for the default register state in the existing MAC
hang check.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Also include common MAC alive check. This should make the hang checks
more reliable for modes where beacons are not sent and is used as a
starting point for further hang check improvements
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the even that the wcn36xx interface is brought down while a hw_scan
is active we must abort and wait for the ongoing scan to signal
completion to mac80211.
Reported-by: Mart Raudsepp <leio@gentoo.org>
Fixes: 886039036c ("wcn36xx: Implement firmware assisted scan")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch provides support to get per peer tids log.
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/
XX:XX/peer_debug_trigger
These logs will be the part of FWLOGS which we collect the logs
via tracing interface. Here we will get the peer tigd logs only
once(not repeatedly) when we write 1 to the debugfs file.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:1593: Statements should start on a tabstop
drivers/net/wireless/ath/ath10k/ce.c:962: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name
drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1639: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/net/wireless/ath/ath10k/htt.h:1660: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kernels built with CONFIG_KASAN=y report the following BUG for rtl8192cu
and rtl8192c-common:
==================================================================
BUG: KASAN: slab-out-of-bounds in rtl92c_dm_bt_coexist+0x858/0x1e40
[rtl8192c_common] at addr ffff8801c90edb08
Read of size 1 by task kworker/0:1/38
page:ffffea0007243800 count:1 mapcount:0 mapping: (null)
index:0x0 compound_mapcount: 0
flags: 0x8000000000004000(head)
page dumped because: kasan: bad access detected
CPU: 0 PID: 38 Comm: kworker/0:1 Not tainted 4.9.7-gentoo #3
Hardware name: Gigabyte Technology Co., Ltd. To be filled by
O.E.M./Z77-DS3H, BIOS F11a 11/13/2013
Workqueue: rtl92c_usb rtl_watchdog_wq_callback [rtlwifi]
0000000000000000 ffffffff829eea33 ffff8801d7f0fa30 ffff8801c90edb08
ffffffff824c0f09 ffff8801d4abee80 0000000000000004 0000000000000297
ffffffffc070b57c ffff8801c7aa7c48 ffff880100000004 ffffffff000003e8
Call Trace:
[<ffffffff829eea33>] ? dump_stack+0x5c/0x79
[<ffffffff824c0f09>] ? kasan_report_error+0x4b9/0x4e0
[<ffffffffc070b57c>] ? _usb_read_sync+0x15c/0x280 [rtl_usb]
[<ffffffff824c0f75>] ? __asan_report_load1_noabort+0x45/0x50
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d0cbe>] ? rtl92c_dm_rf_saving+0x96e/0x1330 [rtl8192c_common]
...
The problem is due to rtl8192ce and rtl8192cu sharing routines, and having
different layouts of struct rtl_pci_priv, which is used by rtl8192ce, and
struct rtl_usb_priv, which is used by rtl8192cu. The problem was resolved
by placing the struct bt_coexist_info at the head of each of those private
areas.
Reported-and-tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Cc: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtcoutsrc.c to use the
standard routines. It also deletes the definitions of the now-unused
debugging macros, and turns on compilation of all the routines in
btcoexist.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8821a2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8821a1ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8723b2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8723b1ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8192e2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the issue specific to AP. AP is started with WEP
security and external station is connected to it. Data path works
in this case. Now if AP is restarted with WPA/WPA2 security,
station is able to connect but ping fails.
Driver skips the deletion of WEP keys if interface type is AP.
Removing that redundant check resolves the issue.
Fixes: e57f1734d8 ("mwifiex: add key material v2 support")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As reported by Felix:
Though protected by an ifdef, introducing an usb symbol dependency in
the rt2x00lib module is a major inconvenience for distributions that
package kernel modules split into individual packages.
Get rid of this unnecessary dependency by calling the usb related
function from a more suitable place.
Cc: Vishal Thanki <vishalthanki@gmail.com>
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This new helper reads extra frequency limits specified in DT and
disables unavailable chanels. This is useful for devices (like home
routers) with chipsets limited e.g. by board design.
In order to respect info read from DT we simply need to check for
IEEE80211_CHAN_DISABLED bit when constructing channel info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver doesn't use mac80211, so it shouldn't include mac80211.h,
include only the necessary cfg80211.h instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Second batch of improvements and fixes for v4.11.
* A bunch of bugfixes for the DQA code;
* Work on support for new A000 devices continues;
* Some clean-ups and general improvements
Some devices with RTL8732BE wifi/Bluetooth adapters are shipped with only
a single antenna. On a subset of these, the EEPROM is incorectly coded
to indicate the wrong connection. The resulting problems have been fixed
for wifi. This change handles them for BT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This routine uses its own debugging macros These are changed to use the
the recently rewritten RT_TRACE macro. There are also some renamed
variables that were missed in the previous step.
The only functional change is that some debugging statements have been
dropped based on the final code supplied by Realtek.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a potential race condition when the control byte of a CAM
entry is written first. Write in reverse order to correct the condition.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support new version of beacon template command which deprecates
the use of the tx command inside.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When resuming, it's possible for the following scenario to occur:
* iwl_pci_resume() enables the RF-kill interrupt
* iwl_pci_resume() reads the RF-kill state (e.g. to 'radio enabled')
* RF_KILL interrupt triggers, and iwl_pcie_irq_handler() reads the
state, now 'radio disabled', and acquires the &trans_pcie->mutex.
* iwl_pcie_irq_handler() further calls iwl_trans_pcie_rf_kill() to
indicate to the higher layers that the radio is now disabled (and
stops the device while at it)
* iwl_pcie_irq_handler() drops the mutex
* iwl_pci_resume() continues, acquires the mutex and calls the higher
layers to indicate that the radio is enabled.
At this point, the device is stopped but the higher layers think it's
available, and can call deeply into the driver to try to enable it.
However, this will fail since the device is actually disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support differentiating between two phys for a000 devices
in order to load the correct firmware.
Eventually when moving completely to the new phy we will be
able to remove this.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_drv structure contains trans which already contains cfg, so
storing cfg separately in iwl_drv is redundant. Remove it and access
trans->cfg instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When iwl_drv_start() is called, trans->cfg must already be set, so
there's no need to pass cfg separately, since it can be accessed
directly from trans->cfg.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3 ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.
As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.
To make this possible we need to move the memcpy() of the TX
command until after it was updated.
This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.
This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware will soon actually look at the AID field, and
when it does that it'll try to ensure that the AID is never
changing. Due to the way the station is added, it may start
with an invalid AID before it's associated, so to ensure a
constant AID (once it becomes non-zero), track the station
state and set the AID only when the station is associated
and when it disassociates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a long-standing bug that was introduced when this code
was introduced: cfg80211 passes a pointer, but we treat it as if
it was passing a value. The result is that we pass the pointer to
the firmware, instead of the value. It's not clear how this could
ever have worked, unless the firmware is ignoring this value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When driver needs to access the contents of a streaming DMA buffer
without unmapping it it should call dma_sync_single_for_cpu().
Once the call has been made, the CPU "owns" the DMA buffer and can
work with it as needed.
Before the device accesses the buffer, however, ownership should be
transferred back to it with dma_sync_single_for_device().
Both calls weren't performed by the driver, resulting with odd paging
errors on some platforms. Fix it.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support getting alive from two LMACs and dumping debug
data from both.
Deprecate older alive notifications no one is using.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
